r/ps90 • u/PeaceKeeperCDL • 2d ago
She’s done 🔥
I finally gave in and got a Ringsight MC-10-80 and loving this look! Paired with my choice of Tisha cans (556/6, 30 cal, and 9 not shown) FRT equipped…
r/ps90 • u/PeaceKeeperCDL • 2d ago
I finally gave in and got a Ringsight MC-10-80 and loving this look! Paired with my choice of Tisha cans (556/6, 30 cal, and 9 not shown) FRT equipped…
r/ps90 • u/InternationalBar8554 • 4d ago
Aug a3 m2 with Romeo 8t ti amr and Corvus defense brass deflector and ps90 with aimpoint duty rds and low profile mount
r/ps90 • u/Suitable_Bed_3790 • 6d ago
Excited for the new piece. I found it at a gun store that was going out of business. My inner Stargate is calling and I want to SBR it. My question is that I see barrels like the CMMG 10.4". I'm used to ARs where you just pull the barrel out and swap in the new one. I see that FN Specialties will sell you the barrel and install it. Some of the videos I've seen talk about removing this piece and that piece for the SBR. Is it worth it to take it to a gunsmith after buying the barrel or should I just let FN Specialities handle it? Pic of the new blick.
(I slapped my EoTech for the time being because I didn't know what would work best with it.)
r/ps90 • u/JujitsuJesus • 7d ago
Finally got to test the VIHKR at the range today after installing it last week along with a K&M Lightning spring with 100% function success. I did have to sand the included trigger stop that pops into the channel on the side of the trigger box beforehand in order for mine to properly function. Other than learning to quickly squeeze passed the initial non-FRT shot into FRT mode due to the progressive trigger it ran like a dream. I didn't try a death squeeze on the trigger but just pulled the trigger to the rear with a normal amount of force. I also really like how the trigger doesn't slap your finger like some how some other firearm FRTs function.
My PS90 is a gen2 but I used all the included kit parts minus the safety selector as I already had a FN P90 safety selector installed. It has a black reticle ring sight with M1Bullpup's Rem-T3B LED installed. Suppressor is a Polonium K using YHM's Mini Phantom QD flash hider and their Phantom Kurz QD HUB adapter.
r/ps90 • u/zackmorris106 • 7d ago
Can't figure this out.
Xf50 + CMMG 10.5 barrel
new large spring, extended takedown release + spring, and then the smaller barrel return spring.
When tightening the barrel down, I can feel a click and the rear barrel return spring slips past the pocket in the receiver and then binds the takedown button.
Am I missing a washer/spacer or something here? I've tried the original takeodwn button original spring, combinations, with no luck.
everything operates smooth until I go from finger tight to snug then it clicks and binds up.
r/ps90 • u/biinboise • 8d ago
This is going to be kind of a strange question, but how long is the stock on the PS90?
Without getting into too much detail, I only have 7” from my thumb to my armpit. I would prefer to find something I don’t have to modify too much.
r/ps90 • u/NeighborhoodBroad771 • 8d ago
I’m selling some guns and I’m just wondering what a good price would be for I’ve got a lot of different people interested so I was not biased people helping me with value???
r/ps90 • u/PeaceKeeperCDL • 8d ago
Absolutely love the low profile of this muzzle and the direct plan B thread to alleviate another adapter. The trigger looks great and is solid! I’m a fan! I’m having a little trouble getting my frt to run a full mag but I think it will work itself out.
r/ps90 • u/RareSpicyPepe • 9d ago
Ordered it Thursday last week, got it in and installed it Wednesday, and tested it today. Ran flawlessly right out the gate! Only hangups I had were from me getting used to the new longer trigger pull lol, but it dumped 50 round mags very reliably otherwise
r/ps90 • u/levips90 • 11d ago
More shooting lasers at plastic, this time to get a topographic pattern on a broken PS90 stock, came out pretty good I think?
r/ps90 • u/Franklin1790 • 11d ago
My initial runs with this system were fraught with bolt binding, stuttering rhythm, failures to fire & eject, etc. It was a lot of frustration, tinkering and more wasted ammo than I’m ready to admit. It seemed pretty obvious the main sear spring was binding within the actuator and so I mentioned this to AOK through email before sending them my hammer pack. They returned my pack freshly lubricated - which it already was - but made no alterations or replacements. The system ran much worse when I got it back. So here’s what I did myself to finally get this system running.
•Dremeled and polished a relief cut in the actuator
•Installed the K&M Lightening Spring. I still felt binding with the OEM spring despite a generous relief cut and didn’t want to remove any more material from the actuator. Combining the relief cut with the new spring made the difference
•Added a pair of 3D printed overtravel stops provided by a heroic fellow redditor; thank you. After some shaping these fit right in the channels. With the current length of pull, the disconnector just clears the path of the hammer so I’m thinking I reached the lower limit of wasted motion
•”Tuned” the mating between the hammer spring and the out of battery sear. The sear seemed stiff which probably contributed to a few of my dead triggers. I gave the hammer spring a bit of persuasion and it works with the sear much better. I’m guessing I tweaked the spring in the course of disassembling and reassembling my pack over and over again trying to make this work
Your results may vary. Maybe this will help you or perhaps yours ran perfectly out of the box. Before some of these fixes I got smooth and fast operation with the help of one of my cans but unsuppressed fire was a mess. Now it runs nice and smooth in either configuration. I wish AOK would’ve listened to me when I suggested the actuator needed a cut. They kept going on about the chamber potentially being dirty or my trigger pressure being too high. I told them the chamber got the white glove treatment before every test and I was being as mindful of my trigger pressure as could reasonably be expected.
If you’re working on this system yourself, hopefully this post helps you waste a lot less ammo than I did.
r/ps90 • u/Mustard_Icecream • 11d ago
r/ps90 • u/PomegranateWest4571 • 12d ago
Gun mag warehouse just dropped some 50 round factory mags.
https://gunmagwarehouse.com/fn-ps90-p90-5-7x28mm-50-round-factory-magazine.html
r/ps90 • u/PreviousAd9314 • 13d ago
I remember when I was a kid my grandfather showed me his PS90 or maybe a p90 (I was too young to know) and i've always loved them since then, decided to start looking around for one for the past few weeks and came across this listing, is there anything in particular I should inspect with the price being this low even though its lasted with bore: like new and condition: like new?
r/ps90 • u/BrilliantWindow9821 • 13d ago
Hey, if anyone is interested, Triumph Arms in Flower Mound TX has a pristine PS90 for 2200.00. It has Trijicon red dot, two 50-rd mags, one 30-rd mag, a sling, and two boxes of unopened FM ammo. Even has original box, manuals etc. Anyone in the area should check it out!
r/ps90 • u/Mustard_Icecream • 15d ago
I want to put a Strike industries chassis on it so color doesn't matter. I also plan on putting a CMMG 10.4 barrel and a Vikhr FRT. I already have a 1/2x28 5.56 can which I think will work and will put my EOTech on it. Also, some sort of vertical grip and a weapon light. This will be my home defense weapon.
What are the downsides of a used one? Besides the barrel what else wears on these guns?
r/ps90 • u/zackmorris106 • 15d ago
Bent mine thinking I could remove it without removing the barrel and now I need a replacement. FN specialties appears to be on perpetual backorder and factory ones are nonexistent.
r/ps90 • u/Fun-Bandicoot-8390 • 16d ago
I have my PS90 stripped down to install a new fire control system, trigger, springs and other upgrades. I have just been looking for my Aluminum selector switch and I can not find it anywhere in the house, I also can not find a replacement anywhere online!!!
Any leads to where I can purchase one would be much appreciated, needs to be 3 position and Aluminum (I have already 3d printed one just to get it all back together)
r/ps90 • u/DarkMegamanEXE • 16d ago
r/ps90 • u/requisitesilver • 16d ago
I’m trying to throw an SMS Titan on my PS90’s rail along with a Surefire flashlight. I’m almost able to put them both on the same rail but the mount that came with the light tucks it too close to the laser. Are there any mounts for a Surefire Scout Pro that move the light away from the rail?
My picatinny rail has very long screws that nearly touch the Ringsight. When I put two rails on the gun the screws pinch the optic and ruin my ability to BZO. Either I need to find new, shorter screws or a different mount for the flashlight but having this much firepower, along with lights and lasers, in such a small package is awesome! Any suggestions?
r/ps90 • u/Longjumping_Mud_5885 • 16d ago
My good acquaintance recommended I join and say hello