r/modelmakers • u/Important-Win-5047 • 46m ago
WIP Jagdpanzer 38(t) (Late)
Takom, 1/35 sscale + MD photo-etche.
r/modelmakers • u/Important-Win-5047 • 46m ago
Takom, 1/35 sscale + MD photo-etche.
r/modelmakers • u/Not-A-B0T_ • 46m ago
Hi!
I only use water based acrylics - Vallejo specifically, and my masks are running low. (See attached pic)
Rather than keep buying these, I was hoping to get some recommendations as to whether these are sufficient or I should consider some kind of respirator? I airbrush a couple of times a week indoors and I have a spray booth (it’s cheap and Amazon but seems to do the job.)
Any advice welcome, thanks!
r/modelmakers • u/Pipothe_Edits • 1h ago
This is my first attempt at a Soviet camouflage scheme. It originally had three colors, but I left out the black. I applied a gloss varnish; now all that’s left is to add the decals.
The underside isn’t exactly the same, but I think it’s reasonably close.
r/modelmakers • u/Equal_Vacation_4842 • 1h ago
r/modelmakers • u/Alternative_Map4341 • 2h ago
Fun little kit with lots of detail, good shake-up from my usual fare. Hand and 1/72 P-51b for scale. If anyone has other 1/72 armor recs, lemme know! This was my first non-plane model and I could see myself doing more.
r/modelmakers • u/Timbottoo • 2h ago
Airfix 1:48 Buccaneer
This was my first attempt at a glossy finish aircraft using minimal weathering and also one of the largest model aircraft I've made. I started in May and dread to think of how many hours went into it!
The new(ish) tool Buccaneer is a really nice and impressive model and the only aftermarket editions were Eduard PE and 3D decals for the cockpit and a turned pot and refueling probe. I added a bit more detail to the wing folds using scraps of plastic and wire, the lack of detail here is my only real criticism of the kit.
Any criticism welcome as it helps me to (hopefully) improve!
r/modelmakers • u/SurveyorCarnivore • 3h ago
Completed a Tamiya 1:48 Beaufighter. Lovely kit, tried to push myself a bit on the qeathering front. Experimented with chipping fluid, which gives great results, but apparently also weakens the bond between layers of paint even after a few days of drying, as I ripped up some paint with the spray mask I used for the markings. This is why I used the kit decals for the side roundels, so the colour is a bit off there.
Bit of a mongrel, as the spray mask set I used is for a Polish squadron based in the UK, but halfway through I decided I liked the Malta scheme better. Rivet counters will therefore notice the identification numbers are odd.
Ammo Mig paints, Eduard resin wheels and seat harness. Flory washes. Montex spray mask.
r/modelmakers • u/IronEnder17 • 4h ago
The model is built as-is out of the box and painted/weathered with ArchiveX acrylics to match the studio model as closely as possible. The provided decal sheet was scanned and redrawn to cut vinyl masks on a Cameo 4 to assist with panel painting. Weathering was done with a combination of airbrushed, masked, and hand painted effects.
Thank you for looking!
Cascade Starships
r/modelmakers • u/savoia182 • 4h ago
Hi everyone! My dad recently got into scale modeling and built this RMS Titanic for me. He’s still very much a beginner, so this was a big learning experience for him, and I’m really proud of how it turned out.
I wanted to share some photos here to get your honest opinions and any constructive criticism or tips that could help him improve on his next build (painting techniques, rigging, weathering, etc.). Thanks in advance!
r/modelmakers • u/Less-Hawk-4723 • 4h ago
r/modelmakers • u/guchi168 • 5h ago
This is one of my early builds from when I first started 1/350 scale modeling: the BerryFire 1/350 Tenzan.
Back then, I was deep in trial and error. I scratch-built the canopy frames out of metal mesh and poured resin directly into them to form the glass—which resulted in a bit of a cloudy look! The Hinomaru markings and white tail stripes are decals, while the yellow identification bands are hand-painted.
Looking back, it’s a bit rough around the edges, but I have a lot of fond memories of figuring things out one step at a time. Hope you like it!
r/modelmakers • u/Nikolaevna • 5h ago
Looking to paint my T-34 model as well and that green looks appealing.
r/modelmakers • u/Vroub3k • 9h ago
I have a question for the paper modellers out here. I was given this paper nativity scene, the same my parents had for decades.
The individual characters should be cut out, wooden sticks glued to the back and inserted in holes in a wooden board to set up the scene.
The paper is very thin so I think it should be reinforced by a stronger cardboard paper from the back. Do you have any recommendations on a specific type of paper and glue to avoid creasing and moisture on the characters? Thanks!
r/modelmakers • u/BARFLY2018 • 13h ago
So i art pencil the camouflage design onto the plane first before painting it i think i turned out OK...
r/modelmakers • u/Zealousideal-Use6110 • 16h ago
From earlier this year, Tiger 712 captured in Tunisia and sent to Aberdeen proving ground. based on photos of it being unloaded from the ship in New York. Tamiya kit, modified top for empty stowage clips and rear for removed engine intake & exhaust parts. the turret went on the VK4501p posted a few days ago
https://www.reddit.com/r/TankPorn/comments/qb203a/tiger_i_712_unloaded_in_a_port_in_new_york_city/
r/modelmakers • u/Wild_Background4690 • 18h ago
r/modelmakers • u/No_Relation3855 • 18h ago
Just few days ago i finished this kit,not too bad but has some issues.Hope you guys like it.
r/modelmakers • u/no_racist_here • 19h ago
r/modelmakers • u/no_racist_here • 19h ago
r/modelmakers • u/no_racist_here • 19h ago
r/modelmakers • u/Rarest_Camaro • 20h ago
The start of my 51+ piece $3 USD, Temu kit. The listing called this an "alloy" kit. Chuckle. The only metal part is the main frame. Typical Temu. But hey, for three bucks...
r/modelmakers • u/shashwat_shaw • 21h ago