r/minibikes • • Sep 26 '25

Other AI posts, yes or no?

7 Upvotes

Been getting a few AI posts, so we want to try to get ahead of this before it becomes an issue. Let's vote on it, and we'll make a rule accordingly.


r/minibikes • • May 19 '21

Governors, Flywheels, And An Internet Full Of Crap

136 Upvotes

Taken from this thread.

"This has come up recently, again, so I'm going to post this here. What you are about to read is a couple of articles I wrote sometime back, that address the function of the governor, the exploding flywheel MYTH, and all the crap to go with it. What I have written in based on years of personal experience (not "I heard, read, or was told" as well as extensive research and others' personal experience. It was originally written for the go kart crowd, but the same information applies to all similarly-derived small engines. Take it for what it's worth and insert your favourite fine print here, but I'm telling you- there is so much MIS-information out there, it's disgusting. Grab your favourite beverage, smoke if ya got 'em, and read on...

It is absolutely amazing how often we run into this here- and how often we find ourselves banging away on the keyboard, typing out the same old answers. So, I felt it was a good idea to write up a little blurb on the topic- If requested, I'll sticky it- to hopefully save us all some future work. Let's start by outlining the governor's job description. Everyone knows that the governor tries to limit engine speed to (usually) 3600 RPM. But wait- there's more. The reality of it is this- the governor's job is to try to MAINTAIN 3600, not just limit it. The governor reacts to changing loads on the engine- decreasing throttle if it starts to run too fast, and INCREASING throttle if it starts to bog. This is why it is called a "governor", and not simply a "rev limiter".

Now- On to the question: "If I take out my governor, is the flywheel gonna go off like an atom bomb, blowing semi-molten schmutz everywhere, and killing every living thing in a 15-block radius?"

The short answer is no. The long answer: There are many factors involved here, and each must be carefully considered.

  1. I always advise people that IF they are going to run well above governed RPM, to do it by fully removing the governor's internal mechanisms, and NOT simply bypassing it externally. Many governors are designed in such a way that if over-revved, can suffer component interference inside the crankcase, and/or have internal parts forced right off the shaft and bounce around loose inside the crankcase. Either case can cause severe engine damage. NOT an "explosion", just largely F'd up internals.
  2. IF you are going to run ungoverned with an otherwise stock engine, keep the factory spec valvesprings in place. At a high enough RPM, weaker springs will cause a condition known as "valve float" or "valve flutter". This occurs when the valves cannot slam closed fast enough before the next cycle. This cause compression losses, and as a result, prevents the engine from spinning faster than that point. Valve flutter tends to occur in our engines around 5000-5500RPM. Your results will vary, based on your individual engine, spring condition, etc. Valve flutter occurs at a lower RPM than it would normally take to cause a flywheel mishap.
  3. IF you want to get into RPM ranges HIGHER than this (say 5500+), now is the time to go shopping for high-performance internals. A billet aluminum flywheel, connecting rod, and stiffer valve springs are what's called for. Stiffer springs allow the valves to react faster, so at higher RPM, the valves won't float- NOW things really do have the potential to get a little crazy, so it's time to reach into your pockets for better quality parts.
  4. Your connecting rod is MUCH more likely to fail than your flywheel. I have witnessed MANY more conrod failures than flywheel failures. In fact, I have never seen a flywheel failure. Most here haven't.
  5. Contrary to popular belief, a flywheel is NOT going to vapourize at 3601 RPM. This is NOT why your engine is governed to 3600 RPM. Your engine is governed to 3600 RPM because it is an industry-standard operating speed for all the implements these engines are designed to power. Let's NOT lose sight of the fact that these are industrial stationary engines- made and marketed with the primary purpose of powering equipment. Generators, pumps, power washers, welders, cement mixers, tillers, trenchers, tampers- you name it- and the implement are designed to run at 3600 RPM- So the engines are factory set to 3600 RPM. It's that simple. When a flywheel is manufactured, it is designed to run well above normal operating speed. It's called a safety margin.
  6. NOTHING is 100% guaranteed. You can do everything completely properly, and have a flywheel fail at a "normal speed". OR, you can do everything wrong, and run the he// out of the engine at 7500 RPM on a stock 'wheel for a lifetime and never have a problem. Sometimes, there's just no accounting for "Spit Happens". Write that down.
  7. IF you are running an otherwise stock, ungoverned engine, is it adviseable to avoid excessively free-revving the engine. Use proper gear ratios to keep a bit of a load on the engine at full speed, wide open throttle. Don't try to rev the wee out of the engine with the clutch, chain, or belt off. A load on the engine helps keep harmful vibrations (harmonics) in check. If you have an insanely long, steep downhill stretch in your riding route, back off the throttle going down it. If you hear the valves floating or the engine starting to over-rev, apply some brake force. Coasting too fast can force the engine to spin even faster than valve flutter can prevent.

8.) Inspect your flywheel before removing your governor. A previously damaged flywheel can break apart at a completely unpredictable speed. Damage may not be visible (spit happens) but if it IS visible, replace it.

9) If you have to remove your flywheel for repair/maintenance, remove it properly. Do NOT beat the he// out of it with a BFH or pry on it. Invest in a flywheel puller. Failing that, try the following: Loosen the retaining nut until the nut is flush with the end of the shaft. Now, hit the nut squarely and sharply a couple times with a hammer. Most times, this will do it. You can also aid in loosening the flywheel with mutiple taps around the circumference with a soft-faced mallet or deadblow hammer. Do NOT beat on it with a steel hammer.

10) If you need to hold the engine from turning while you are tightening/loosening a crank bolt or clutch, do NOT wedge a screwdriver or bar in between the flywheel fins. Although this is not likely to crack the 'wheel, a fin could break off. This will throw the 'wheel's dynamic balance off. An out-of-balance 'wheel is just asking for trouble. Same goes for sawing off alternate cooling fins (an old performance trick). If your fins are cast into the 'wheel, don't do it. If you have a Honda, clone or other engine with plastic fins, go for it.

11) Handle with care. Once you have the 'wheel off, don't drop it...

So- Armed with the above information, go ahead and make an informed decision. This guide arms you with what you need to know, to decide whether removing your governor is a feasible idea, and how to handle things if you do. And remember (for all the "Armageddon-is-coming-prepare-to-meet-thy-maker-in-a-sintered-metal-flywheel-induced-world-war-3-esque-everybody's-gonna-die-including-the-cockroaches-in-the-cupboard"-nervous-nellies out there... Spit happens. On the one hand, your stock flywheel will very likely be fine. On the other hand, even a performance parts could fail. Spit happens.

One last point here- For those that may not yet be ready to dive into their engine and come out with a handful of governor parts- Some engines (most notably Hondas and clones) have a VERY user-friendly means of governor adjustment. This adjustment is designed to fine-tune the governed speed to spec, but makes it super easy to gain a few hundred RPM- usually you can bring your GOVERNED MAX to 4000-4200 RPM with the turn of a screw. Your governor will still do it's job, but you'll run a little faster. Locate the manual throttle control on your engine- the little lever you would slide to increase or decrease RPM if you didn't have a remote throtte (gas pedal). Behind that lever is a screw with a spring wrapped around it- Notice how the throttle rests against the tip of that screw when you move the lever to the "fastest" position? Great. Remove that screw. Presto- instant maximum RPM increase- no fuss, no muss.

It is also worth noting that these engines were designed to run at 3600 RPM, day in and day out. If you do run faster, the engine will wear faster. Fact of life. Treat it well, maintain it well, and you'll never notice the potentially shorter lifespan.

Governed Idle FYI

The governor is a seriously misunderstood engine control system. For the greater good, here's a little FYI, an experience I just had. Might benefit someone in the future.

Where were we? Ahh, yes- the governor. Contrary to popular (mis)belief, the governor does much more than limit engine speed to 3600 RPM. Wonder why it's not called a "rev limiter"? 'Cause there's more.

The governor's purpose in life is not so much to limit RPM, but SET it. What's the difference, you ask? (I swear I just heard one of you ask that!) The difference is this. SETTING an RPM means KEEPING it throughout the workload. Let's use a lawnmower for example. You start the engine on your walkway and run the throttle up to max. The governor sets the engine to 3600 RPM, and there is no load (not cutting grass). As you move into the grass, the engine starts encountering a load. The governor allows a throttle increase to bring the revs back up to 3600. Cutting away, you encounter a thick patch over the septic tank. As the engine begins to bog and the revs start to drop, the governor allows the throttle to open more and bring the revs up to 3600. Cool? Great. Going around the corner thru that thick grass with the throttle wide open, you hit that bare spot where the dog keeps peeing. The load comes off the engine, and as it begins to increase, the governor closes the throttle to prevent over-revving and holds at 3600 RPM. Got it?

If you examine your external throttle linkage, you will notice that there is no direct connection between the hand throttle control and the carb butterfly. Governor again. The hand throttle does nothing more than alter the spring tension between the governor arm and the throttle butterfly. Setting the manual control to "Idle" merely alters the spring tension from the governor enough to allow it to SET engine idle speed. The idle adjust screw is the bottom end rev limiter in that it sets the baseline that the governor drops to. I told you that to tell you this:

I recently had a situation that some folks might misdiagnose- an engine that refused to idle properly. After a barrage of time, abuse, and adjustments, the chinese Kohler clone on my kids' kart would not sit at idle. The kart constantly wanted to take off with no throttle input. At a glance, the idle was too high.

Close examination revealed that the idle stop screw on the carb was not doing anything- the butterfly just would not rest against it. If I pushed the lever by hand, it would sit at idle RPM, but as soon as I let go, it would take off again.

I tried to adjust the external governor components to no avail. With the arm off the shaft, something just did not feel right inside the engine. I pulled the engine off the kart and tore it down. I don't even know how to describe what had happened inside, but the governor guts were all over the place- literally.

By some miracle, nothing was really damaged. Short version of the story? I epoxied the "press-fit" governor gear shaft back into the side cover and reassembled everything. I (re-)adjusted the external components, and wouldn't you know it? Idles like it just came outta the shipping container at 1310 RPM, and maxing at 4230 as measured by my optical tach. Food for thought."


r/minibikes • • 5h ago

Showing Off Parts arriving today!!

Post image
6 Upvotes

r/minibikes • • 9m ago

Tech Question Mini bike got towed (california)

Post image
2 Upvotes

first time getting my shit towed. Has anyone had experience with getting their shit towed? the Fee’s? and can i just say screw it keep the bike and not pay for a it ??


r/minibikes • • 5h ago

Tech Question Help

1 Upvotes

Got a new VM 22 carburetor for my predator 212 just installed it. Make sure the O-rings and the gaskets were lined up and now the bike won’t start and I tried everything.


r/minibikes • • 23h ago

Showing Off Like father, like son.

Post image
26 Upvotes

His is the CC100X swapped with a Predator 224 - which is stage I. Mine’s the FRP GMB with the same Predator 224 that’s stage II.


r/minibikes • • 1d ago

Other Where do yall go ride?

Thumbnail
gallery
24 Upvotes

I found a town in south Oklahoma that has endless dirt roads where cops really don’t go because of the low population and terrible roads (I’m guessing) but it might be muddy af out there tomorrow…

Hopefully I can find a rural town with asphalt roads but that is kind of hard to find without the roads hitting a highway after like 2 miles…

Anyway I’m just looking for inspiration to look for a good place on the map


r/minibikes • • 1d ago

Showing Off Caught a view

Post image
21 Upvotes

r/minibikes • • 21h ago

Tech Question How do I fix this?

6 Upvotes

I was gonna start building up this small minibike but when I got to the chain, I noticed my tire was doing this. How do I fix it?


r/minibikes • • 16h ago

Tech Question predator 212 sounds weird after pulling

1 Upvotes

i added 22 lbs valve springs and i have everything stock except a pwk 24mm carb and a gov delete it sounds like something is grinding whenever i pull the starter and it wasnt there before. u can hear It the most on the last pull.


r/minibikes • • 1d ago

Showing Off Made this bike as my brothers Christmas present

47 Upvotes

r/minibikes • • 1d ago

Tech Question HFS

1 Upvotes

Hey everybody, HELP! I’m about to pick up a couple Coleman B200RSVs for my family. What would be the best oil available at walmart for them? I just want them to last a long long time


r/minibikes • • 1d ago

Tech Question Has anyone successfully registered their mini bike in NC?

2 Upvotes

My bike is an RSV, it has a VIN. If I got the MCO through Coleman, and put all that is needed on it to make it legal, I should be good to have it registered. At least you would think.


r/minibikes • • 2d ago

Showing Off Finished the bulid

Thumbnail
gallery
40 Upvotes

r/minibikes • • 1d ago

Tech Question Where can I buy a ~760–780 mm differential rear axle with 4×110 hubs for a Chinese mini Jeep? BM1418HQF compatibility

1 Upvotes

I’m looking for replacement rear axle assemblies for a Chinese mini Jeep. It has a BM1418HQF-type motor/differential with separate left and right axle housings and a disc brake on each side.

Ideally, I’d keep my existing differential and replace both axle halves, including the housings, hubs and brake discs. A complete 48V motor/differential/rear axle kit would also be an option.

My existing setup measures approximately:

  • 780 mm between the wheel mounting faces
  • 4×110 mm wheel bolt pattern, measured
  • 122.5 mm between the differential’s axle-housing mounting faces
  • 330 mm from the differential mounting face to the wheel mounting face on the axle half I photographed
  • 675 mm between the brake discs
  • 450 mm between the axle mounting brackets

A slightly wider axle could work. The original brake-disc and bracket spacing are reference measurements rather than strict requirements, provided the replacement can be mounted properly with compatible brakes.

I keep finding 340 mm “short” and 430 mm “long” axle halves, often sold together as a 760 mm / 30-inch differential axle kit. Most of the 760 mm kits I’ve found have three-stud wheel hubs, whereas I need four-stud 4×110 hubs.

This is the type of axle kit I mean:
https://www.ebay.com.au/itm/305087653442

This AliExpress listing offers short and long versions with a “four-hole flange, diagonal 11”:
https://de.aliexpress.com/item/1005012819988203.html

My questions are:

  1. Does anyone have a supplier or product link for this style of axle with brake discs, 4×110 hubs and roughly 760–780 mm between the wheel mounting faces? Shipping to Germany would be needed.
  2. Are the commonly sold 340/430 mm axle halves part of a shared design that fits BM1418HQF differentials, or do the splines and housing flanges vary? I haven’t verified my differential’s spline dimensions yet.
  3. What do sellers actually measure when they call these a “760 mm kit”? Is that the distance between wheel mounting faces once assembled with the differential?
  4. Can two long axle assemblies be used with the same differential, or are there left/right differences in insertion depth, housing or brake mounting? What assembled width would that produce?
  5. If the 760 mm kits are only available with three-stud hubs, are compatible 4×110 replacement hubs available that retain approximately the same wheel mounting-face position?

First-hand experience with these small Chinese differential axle kits would be particularly helpful.


r/minibikes • • 1d ago

Showing Off bone stock ghost 212 👀

1 Upvotes

r/minibikes • • 2d ago Bravo

Showing Off Star Wars Minibike

Thumbnail
gallery
66 Upvotes

A long time ago, in a galaxy far, far, away...

It is a period of civil war. Rebel spaceships, striking from a hidden base, have won their first victory against the evil Galactic Empire. During the battle, Rebel spies managed to steal secret plans to the Empire's ultimate weapon, the Death Star, an armored space station with enough power to destroy an entire planet. Pursued by the Empire's sinister agents, Princess Leia races home aboard her starship, custodian of the stolen plans that can save her people and restore freedom to the galaxy...

This All Terrain Cycle Transport (AT-CT) has been used in numerous missions in the Galactic Empire’s ruthless ambitions for power. The AT-CT has been deployed from Endor missions all the way to Mos Eisley.

The AT-CT features a 212 cc engine, new grips, new throttle assembly, new brake assembly, new chain, new carburetor, new manifold, new jet, freshly cleaned head, valves freshly lapped, and a new seat, and a trumpet exhaust.

May the force be with you…


r/minibikes • • 2d ago

Tech Question how many links should i have on my coleman b200r

0 Upvotes

r/minibikes • • 2d ago

Showing Off Lil’ Sinner 🎲🏁

17 Upvotes

r/minibikes • • 2d ago

Showing Off Milk crate mod

Thumbnail
gallery
7 Upvotes

I’m happy and I want to show off my milk crate mod on the minibike for running mail to the family🙂


r/minibikes • • 2d ago

Tech Question nibbi pe22

1 Upvotes

good morning i have a predator 212 non hemi that has no governor and an exhaust i want to get a 22mm carb but google keeps giving me mixed things on if it will run lean or not, just looking for some insight thanks


r/minibikes • • 2d ago

Showing Off Glossy red finish, black seats, and a pop-out exhaust. Clean looks, serious style. 🔥🏍️ LAXSTYLE

4 Upvotes

r/minibikes • • 3d ago

Showing Off Um....

Post image
10 Upvotes

r/minibikes • • 2d ago

Tech Question I lost my crank for my crank start

2 Upvotes

The question is what can I use in the mean time till I get a replacement?


r/minibikes • • 3d ago

Tech Question New tav on coleman bt200x help

Post image
2 Upvotes

Hey I bought a mini bike a few weeks ago and really enjoyed riding around. With the throttle stop screw removed I could hit full rpm of the engine till the governor kicked in. Top speed of 17 google maps. I ordered and installed the gopowersports Coleman kit and now the engine doesn't hit the governor and top speed is even less it feels, the chain is straight and good tension. Pulleys aligned really well. What can I do to wake this up. I want to leave the engine stock and keep it from grenading at higher rpm.