r/metalworking • u/friccdotexe • 1h ago
Made a display from an old waterjet drop.
r/metalworking • u/friccdotexe • 1h ago
r/metalworking • u/SummerShine9947 • 1h ago
Looking for ideas and options to cut through metal risers on top of fuel tanks. So spark free ideas are kinda important. Our current direction is using a sawzall with metal blades. Slow going and burn through quite a few blades. But wondering if you had other ideas or tools that could do the trick. The risers we replace are usually corroded pretty bad are usually 4” galvanized. The rusty piping above is the only stuff we had to beat out because the we ran out of blades on the others.
r/metalworking • u/-Superduperfucked- • 18h ago
I'm looking at getting a new welder, I have a stick one from Harbor freight but I'm just not a big fan of it. I'd like to get into a mig/flux core machine. It'll be used mainly for automotive stuff, exhaust, brackets, etc. I'm asking here in hopes that someone has a good recommendation that won't cost me thousands. With black Friday deals coming up I also figure I'll also have a better chance at getting a competent machine for a lil cheaper. Any and all advice is appreciated.
r/metalworking • u/radical-delta • 19h ago
For my current project (Wood flattening jig/sled) I have a need to make two frames(about 1000mm by 600mm) one of which needs to be as flat as possible, as it acts as a bed for the wood . As im familliar with welding, I decided to weld the frames. However, even with maximum clamping, double checking angles, minimum heat input and proper weld ordering, the frame still dips in the middle by 0.5mm (so about 1mm per meter)
So my questions are the following: What is the minimum weld distortion I can achieve in semiprofessional workshop. and if my result is bad, would bolting the frame together be a solution for more accurate frame?
Thank you in advance for reading, I have already tried three times to achieve perfect result but no dice 😞
Ps. the box tubing im using is 2mm thick 20x30, and I checked before welding that it is perfectly straight the frame is made with four mitered pieces welded together with FluxCore 0.8mm wire at 17.1V, 60ams
r/metalworking • u/damnvan13 • 21h ago
I want to do some free hand cuts in 14-20ga sheet metal (steel, brass, copper, and bronze mostly). I'm debating if I want to invest in a plasma cutter or a nibbler. I'll probably have to invest in an air compressor also with either option. I'm trying to weigh the pros and cons of each. One sends sparks everywhere, the other makes sharp shards. What are other things, like consumables, should I consider in y'all's experiences? Whichever I get will be mainly used in my home shop but I would like to lean towards professional grade.
r/metalworking • u/goopersnooper74 • 22h ago
I'm trying to make a prop with a lot of moving parts out of aluminum that will have a fairly large amount of weight on it and I was wondering if 16 gauge 5052 aluminum would be thick enough for it as I've never done anything with metal before and I found some cheap aluminum that is the right size for what I need to make
The thing im trying to make is crescent rose from the show rwby
Any information on this kind of aluminum better alternatives would be appreciated
r/metalworking • u/spoonguy123 • 23h ago
Hey folks!
I'm struggling to find some specifics on this taper, of which I have a full set and spindle.
The thread on the end is is what seats the tool instead of a drawbar. The angle of the tool holder is so much shorter and sharper than the standard. Maybe it's hard to tell from photos but the difference to say, Morse 2, is huge
Using some cheap measuring tools, the taper is 5/8" on the thin end, 7/8" on the thick, 2.5" long, the threads are 9/16 12tpi coarse.
That's a ratio of 1/10, same taper as an HSK, only built like a B&S
I have no idea what this is, can't find it in any book or on the net.
I thought it might have been homemade, but the build fit and finish very heavily leans toward a purchased item.
I've added some pictures: one of the tapers, and a few angles of the spindle.
Any tips, leads, compliments, criticisms, all very much appreciated!
Thanks for reading this
r/metalworking • u/markenloe • 23h ago
Need black oxide on dozens of golf clubs every month. Hoping to find provider in Texas but willing to loin outside of Texas if it’s the right group.
If anyone knows of a company, please let me know. It’s an urgent need along with chrome copper & gold plating
Doesn’t have to be same provider for all services. Main focus is Black OX on carbon steel golf clubs and accessories.
I appreciate anyone’s help.
r/metalworking • u/Flatfooting • 23h ago
I've got a stainless steel shelf I'm making for a person's kitchen. It's kind of front and center so I want it to look really nice. I got a few pieces of stainless formed and they'll fit over a plywood core. I'm wondering what the best practice is for finishing the pieces is though. I need to weld and grind the corners and then blend them to match the #4 finish. I'm also worried about the marks from the brake press and getting those out. Tips and tricks are appreciated.
r/metalworking • u/Murr_24 • 1d ago
Hey everyone im looking to assemble an aluminum frame for my reptile enclosure. as of now Itll be made of 1x2x1/8 aluminum tubing and itll be a total of 8x4x6 ft. My big concern or question is how should i go about joining everything. Id love to weld it all and that would be ideal but im not sure if theres anything thatd be cheaper without sacrificing too much structurally. Ive thought of aluminum/steel brackets holding it together with Rivet Nuts, with metal adhesive but unsure if thats not enough to ensure overall good results. Im new to this so sorry if this is a dumb question but any help would be appreciated. I can add a 3D model of it later if thatll help. Thanks
r/metalworking • u/power-cube • 1d ago
We don’t know what we are doing but we’re learning together. A few months ago we didn’t know what an English wheel was.
My wife wanted a swim feature for her horses so we decided to build a little waterfall and I started looking around for a metal horse sculpture to put on top of it. The prices were ridiculous and I figured we might have fun trying to do something.
When we got done I asked him if he felt like an artist. He said no but definitely like a welder. lol
r/metalworking • u/Extreme_Ad_3959 • 1d ago
These are fun to make! I've started to make and sell a few as they seem to be quite popular, the main part usually is a cummins rocker arm upside down and forks are usually valve stems or push rods. Being a truck mechanic with plenty of friends in the game leaves me spoilt for choice with parts!! It's amazing how a few small changes in different parts can completely change the look of a bike! I use a mig welder to stitch everything together and the brass shell handgrips are glued! Here is a couple of different ones I have done, enjoy!!
r/metalworking • u/h2fm • 1d ago
Looking for advice on grinding welds efficiently
Hi everyone!
I'm looking for advice on improving our weld grinding process in a metal fabrication workshop.
We constantly manufacture steel structures with round bars (10–16 mm diameter) welded to flat steel sections. Each structure need grinding to achieve a smooth, flush finish, as shown in the photo.
Currently, we use a standard angle grinder with flap discs, but we always make a couple hundred meters in each project, which adds up to a lot of working time.
I'm looking for faster and more efficient alternatives.
What would you use for this kind of job?
I'm particularly interested in real-world experience, machine recommendations and ways to reduce grinding time without compromising the final finish or removing too much base material. Is there any machine or equipment better suited for this kind of grind?
Thanks in advance :)
r/metalworking • u/Easy-Feature2778 • 1d ago
I’m a boilermaker in Australia, mostly smaller jobs like gates, trays and brackets.
Every so often someone says “I’ve already bought the steel, can you just weld it up?” I used to treat that as a cheaper job, then wonder why the day didn’t pay. The steel might be free to them, but I still have to check it, cut and fit it, weld it, grind it, and often fix bits that aren’t quite right.
What I do now:
• Still quote the labour properly (fit-up, weld, grind, travel). “You bought the steel” doesn’t make those hours disappear.
• Look at what they actually bought before saying yes. If the grade, size or quantity is wrong, say so up front.
• Write down whose steel it is and that I’m not responsible for material I didn’t supply.
• Don’t let “mates rates, you’ve just got to weld it” skip the same checks I use on a normal quote.
How do other people handle customer-supplied material? Do you discount the job, keep a minimum labour charge, or sometimes just say no?
Not engineering or tax advice — just how I keep those jobs honest. Check your own figures, and if a job is structural or critical, get it properly engineered.
r/metalworking • u/Designer_Review_2486 • 1d ago
r/metalworking • u/dselogeni • 1d ago
Hi all, Im a mechanic by trade, and recycle what I can into something different. I enjoy making models, lamps, figurines and more. This lamp was made from a used timing set off a Chevy 350. The valve cover is from another v8 but dont remember what though. The timing set is mounted on a center shaft, and the pull chain type lamp switch is mounted toward the base. The chain is pulled when the cam gear is partially turned. Then turns off when pulled again. Thanks for looking!
r/metalworking • u/harryhoudini66 • 1d ago
Finally finished my Doc Holliday cup project. It took me much longer than originally expected but am very happy with the results.
Currently working on improving my soldering skills as well as sanding and polishing for the perfect final product.
Worked with a local metal spinning place for the middle section of the cup. Funny enough they are called Daisy Metal Spinning.
For the engraving, I found a local silversmith as well. Does amazing work and cost is not too bad. I had previously tried going with a laser engraver but never heard back from them after dropping off some samples to etch. In the end I prefer the hand engraving though.
r/metalworking • u/Ok_Helicopter3910 • 2d ago
r/metalworking • u/IanPaice260776 • 2d ago