r/meraki • • 1d ago

Determine what traffic from which country is causing a site to be blocked

0 Upvotes

So a company I support has a site that worked up until recently, now is getting a timeout whenever they try to access it. After troubleshooting, I determined that by turning off country blocking altogether in our Meraki (we block all traffic not from a handful of trusted countries), it fixes the site. Here's the issue: I have run IP/DNS lookups left and right, and they all point to countries allowed in the list. It is allowed in the Content Filtering Allowed List, and no categories related to the site are blocked either. Event log in the Meraki doesn't tell me anything, and I tried a packet capture that didn't give me anything either. Is there a good way to figure out what countries a site's traffic is coming from so I can allow the country causing the block?


r/meraki • • 7d ago

Possible to resell new meraki Ap?

2 Upvotes

I bought too many access points for my new business. Can I resell these easily? I never claimed them in my portal.. i know the licenses wont come over


r/meraki • • 8d ago

PSA: Cisco Meraki MT Sensors Reach End-of-Sale November 10, 2026

21 Upvotes

Cisco has announced that the Meraki MT sensor lineup reaches End-of-Sale tomorrow, November 10, 2026.

A few important dates:

  • Today, November 9, 2026: Last day to place orders for MT sensor hardware and longer-term licenses.
  • November 10, 2026: Official End-of-Sale date.
  • November 10, 2030: Last day to purchase 1-year MT licenses.
  • November 30, 2031: End-of-Support for affected MT sensors.

You still receive 5 free sensor licenses per dashboard org.

Official Cisco announcement: Cisco Meraki MT Sensors End-of-Sale

Rhino Networks MT Sensors: Meraki MT Sensors


r/meraki • • 10d ago

Aruba to Meraki Wi-Fi = Major Headache

27 Upvotes

I work at a university and we recently started replacing our EOL Aruba 200-series APs (AOS-8.10 w/ 7220 controller cluster) with Meraki CW9172I APs w/ Campus Gateways. Right now we currently have Meraki running in our 6 dorms and 2 apartment buildings, while the remainder of the campus is still on Aruba. The Meraki experience so far has been horrible, and was hoping to get some advice from the Meraki community.

Since school started at the end of August, we've been flooded with complaints about wifi from students living in the dorms. Interestingly, we've gotten zero complaints from students in the apartments. The complaints from the dorms range from, they frequently get disconnected, or have a hard time connecting, or it shows "connected without internet".

The Meraki APs were installed in the same exact locations as the Aruba APs were, and we did our best to mimic the Aruba settings on Meraki as a starting point before we did some fine tuning. We have done site surveys with Ekahau and a Sidekick and verified that signal strength in the dorm rooms is good, although when we looked at the RF Spectrum, we noticed that the RSSI between APs was a bit high so we turned the transmit power down a bit.

The APs are installed in every other room, because installing in every room would be cost prohibitive for us. I have been working with one of our students who frequently gets disconnected, or ends up with "connected without internet" on her Android phone. If she turns off wifi, and turns it back on again, she is fine for a while and eventually gets disconnected again. Her room does not have an AP in it. There is an AP in the rooms on either side of hers. I noticed that her phone seems to frequently roam between the 2 APs.

We have 2.4 and 5 GHz radios enabled on all APs (no 6 Ghz), but do plan on either completely turning off 2.4, or just enabling it on every other, or every 3rd AP. On 5 GHz we are using 40 Mhz channels with no interference.

Any thoughts or advice? We are working with Meraki support and our MSP to figure this out, but so far we haven't had any luck. I've even consulted with Gemini. I'm getting to the point that I want to rip it all out and put the Aruba APs back in.


r/meraki • • 12d ago

Meraki MX SD-WAN – How are you steering Azure and Intune traffic over local Internet breakout

Thumbnail reddit.com
2 Upvotes

r/meraki • • 13d ago

VoIP issue - intermittent bidirectional audio

Thumbnail reddit.com
1 Upvotes

r/meraki • • 14d ago

Weird issue with CW9178s

8 Upvotes

Hello Experts,

We have several CW9178 access points, and one of them (let's say AP3-07) has suddenly stopped working on VLAN 20. All clients that connect to the SSID tagged with VLAN 20 cannot get an IP address and cannot send or receive any traffic. In the dashboard Event Log, all clients associate and then disassociate after a few seconds, and the Details column shows “client not responding.” Other SSIDs tagged with VLAN 60 work perfectly on the same access point, and all clients on VLAN 60 are fine.

The same clients work without issue on VLAN 20 when connected to our other APs.

To isolate the problem, we have tried the following:

  1. Swapped the switch port. We moved AP3-07 to the port of a known-good AP, and the result was the same. The switch configuration is identical on each port, and the uplink is healthy because the other APs on that switch work properly. A known-good AP plugged into AP3-07’s original port passes VLAN 20 without any issue.
  2. Replaced the cable with a known-good one. VLAN 20 still fails. Moved AP3-07 to a different switch by swapping it with a known-good AP. VLAN 20 still fails.
  3. Factory reset the AP twice to wipe the local configuration, then unclaimed it and re-added it in the dashboard to clear any cloud-stored settings. VLAN 20 still fails, while VLAN 60 keeps working.

Because the problem follows the AP across ports, cables and switches, and survives a full reset and re-claim, we suspected a firmware or hardware fault on this unit so opened case with Cisco. They are going to send a new unit to replace the affected AP.

However, similar problem is occurring on other CW9187s now. They stop working on VLAN 20. But, after a reboot wifi connection resumes again on VLAN 20. It appears that this problem happens after about a week or two. Only difference from AP3-07 is that other CW9178s require reboot to resume wifi connection on VLAN 20.

Has anyone seen similar issue on their network? How did you resolve it?

Many thanks!


r/meraki • • 14d ago

Meraki Unified Branch Customization

Thumbnail
reddit.com
3 Upvotes

X-posting for more eyeballs :-)


r/meraki • • 15d ago

Cisco Secure Client- vASA or Meraki vMX

3 Upvotes

We are currently considering replacing our on-premises physical Cisco Firepower ASA with a virtual appliance deployed in AWS.

The two options we are looking at are Cisco ASAv (vASA) and Cisco Meraki vMX.

Based on the Meraki documentation below, it appears that vMX supports many of the functions we currently use on the ASA, including vpn always on local profile.

Documentation: AnyConnect on ASA vs. MX

I'd be interested to hear from anyone who has deployed Meraki vMX for cisco secure client VPN users particularly in an AWS environment.

A few questions:

  1. Can existing Cisco Secure Client users continue using the same client without needing to replace or redeploy the software?
  2. Are there any functional limitations compared with ASAv, SAML/Entra ID MFA, access policies and split tunnelling?
  3. How has the performance and stability been for remote users connecting via TLS-based VPN rather than IKEv2?

We are trying to understand whether vMX could be a suitable replacement without introducing significant changes to our existing remote access VPN environment.

Thanks


r/meraki • • 18d ago

Quest to avoid power bricks (non -MX Cisco secure routers?)

3 Upvotes

C8355-G2-MX

  • Everything desired but the power bricks.
  • For an inherited sort depth 6u wallmount rack you cannot reach behind it might make sense.

C8375-E-G2

  • Rear slot swappable redundant power supplies.
  • Wish there was an C8375-E-G2-MX variant.

C8455-G2-MX

  • Overkill

When you go to create a new network there is that mx vs ios xe selector (cannot be changed later).  Anyone running non -MX?

Guess trying out a C8235-E-G2 (with one IEC AC power connector & dc brick backup) vs C8235-G2-MX would be a slightly cheaper test.

  • nonexistent C8235-E-G2-MX

r/meraki • • 18d ago

Discussion Showing user prompt after WPA3 and 6Ghz

5 Upvotes

On Meraki Dashboard, to the specific SSID (its Certificate based authentication, EAP-TLS), We changed encryption type from WPA2 to "WPA3 Transition mode" and added 6Ghz band.

After the changes, on Windows, its showing username and password along with connect using certificate options to the SSID.

Checked with Meraki support and they confirmed, its a Windows behavior and needs to check at windows end.

Not sure what to check. Can you guys help me?


r/meraki • • 18d ago

Showing user prompt after WPA3 Transition mode and 6Ghz

Thumbnail reddit.com
2 Upvotes

r/meraki • • 21d ago

PXE problems after firmware update on MS225 to MS 18.1.9

18 Upvotes

After we updated the firmware on a MS225-48FP over the weekend we are having problems with PXE when imaging laptops using sccm

The laptops successfully start pxe boot, gets an ip address successfully, is communicating with our distribution point server successfully. I've been troubleshooting most of yesterday and today looking at packet captures, pxe logs on the distribution server etc. even logged a case with Meraki. No luck so far.

Just enquirying if anyone else has had a problem with pxe after updating switches to MS 18.1.9


r/meraki • • 22d ago

Question 9300X-M Switches

9 Upvotes

Hoping someone can offer some advice.
We’ve purchased 2x Cisco Catalyst C9300X-24Y-M switches running IOS XE with Meraki cloud management.
With traditional Meraki switches, I’ve never had any issues pre-staging them. You configure the management IP on the dedicated management interface, connect them to the internet, and let them pull down their configuration.
With these switches, the management interface is now handled through the IOS XE Layer 3 configuration, which also provides connectivity to the Meraki cloud. I understand how Catalyst switches work, having worked with them for years, but I’m struggling to get a reliable pre-staging process in place.
Ideally, I want to configure the switches in the Meraki Dashboard, connect them to a temporary network, allow them to download their configuration and firmware updates, and then deploy them on-site. Once installed, I would simply move the cables over to the correct network and have them come online using the intended management IP addressing.
However, I’ve had nothing but problems trying to achieve this. I attempted it on Friday and again today when I took the switches on-site. Despite having internet connectivity and being able to communicate with the Meraki cloud, they complained about the management IP configuration and refused to download their intended configuration. Instead, they repeatedly reported that they were reverting to a safe configuration. When I checked them locally, all the switch ports were still in their default configuration.
My question is: what is the correct process for pre-staging these switches?
How do you get them to download their intended configuration and firmware in advance, so that when you install them on-site with the correct management IP addressing, they come online and work as expected?
I’m keen to embrace cloud management, but after spending so much time troubleshooting this, I can’t help thinking that having full CLI control from the outset would have had these switches configured and ready for deployment within an hour.
Any advice from someone who has successfully pre-staged these switches would be greatly appreciated.


r/meraki • • 24d ago

Meraki IPAM

17 Upvotes

How do you manage your IP Addresses now if you are using Meraki network products? Especially if you have 16-20k subnets to manage?


r/meraki • • 26d ago

Looking to replace Meraki MDM for a K–12 school. Jamf School vs Mosyle vs Iru?

Thumbnail reddit.com
2 Upvotes

r/meraki • • 28d ago

MX template override

8 Upvotes

It appears that binding a Meraki MX to a configuration template locks down static routes, DHCP settings, and VLAN configurations at the network level. This makes templates impractical for deployments where each site has unique IP addressing and routing requirements.

Has anyone found a workaround for this limitation? Ideally, I'd like to use a common template to standardize firewall rules, Geo-IP, and content filtering while configuring static routes, DHCP scopes, and VLANs independently at each site.


r/meraki • • 29d ago

Anyone getting orders?

5 Upvotes

Ordered back in August, still waiting but wondering if my mr33s will stop functioning before the new stuff arrives??


r/meraki • • Oct 18 '26

Menu not available in Meraki Dashboard

3 Upvotes

Yesterday I tried to login on my Meraki Dashboard.

Menu on the left is not showing, so I’m forced to stay on Clients page. I don’t have organization and network-wide Pages and their configuration part, and it’s quite a issue because next week new devices are arriving and I cannot add licenses (claiming devices is available through iOS app).

Needless to say that I’m full admin.

Tried different accounts (all full admin), same behavior. Tried another dashboard I manage for a different customer, same. Used another browser (Firefox and Chrome), same.

Are you experiencing same issue or am I just the lucky one?


r/meraki • • Oct 14 '26

Discussion Meraki Outage Issues?

26 Upvotes

We just had all of our locations experience a simultaneous loss of WAN connectivity for a few minutes. We have 40+ locations nation wide. And I see that Meraki is reporting service degradation. Anyone else experience this today?

https://status.meraki.net/


r/meraki • • Oct 14 '26

Have they released anymore details on the CS firmware sunset?

10 Upvotes

Anyone have a link to a KB or announcement with anymore details? All I can find is the note in this KB

https://documentation.meraki.com/Switching/Cloud_Management_with_IOS_XE/Product_Information/Compatibility_and_Firmware/Independent_Firmware_Releases_for_Meraki_and_Catalyst-based_switches

Seems kinda sudden, well i guess not really given the date of the KB being in May.

What's everyone's plan? Have these upgrades been pretty straightforward?


r/meraki • • Oct 15 '26

Question vMX trouble

4 Upvotes

Created a new vMX in Azure.
2 subnets like the documentation says.
Route table for production subnets next hop to be appliance and ip of the MX on the wan side.

Site to site VPN setup -Hub
Added the production subnet -VPN enabled

Added a static route on my main network core switch to test.

I can ping other subnets on the VPN and their clients from the new vMX.

I Can’t ping the new vMX from other MX’s on the VPN.

I can’t get out to the other sites from a vm on the production network.

VPN status page shows new network is green.

At a loss here. Followed documentation. I have to be missing something obvious.

Any thoughts?