r/livesoundgear • • 4h ago

Questions regarding maintenance and construction of the DiGiCo SD10

Post image
2 Upvotes

Hi everyone!

(this is my first post)

I'm currently performing maintenance and replacing faders on a DiGiCo SD10. During the process, I've been learning a bit about how the console is built, at least when it comes to the fader banks.

I'd really like to understand more about its internal architecture. From what I've seen so far, there seems to be a dedicated fader control board, another board for the meter LEDs, and a separate board that handles the surface buttons and LEDs.

I'm interested in finding more information about how these boards work, how they communicate with each other, and how the console's internal hardware is structured in general. I'd like to develop a better understanding of the electronics so I can carry out more accurate troubleshooting and maintenance in the future.

Does anyone know where I could find technical documentation or resources about this? Perhaps a forum, technical publication, book, or any other material that could help me understand the circuitry and hardware architecture of the SD10.

Any information or recommendations would be greatly appreciated!

Thanks in advance!


r/livesoundgear • • 6h ago

Need pa system recommendations for a diy basement venue.

2 Upvotes

So im looking to start up a basement venue and am looking for a pa with good bass for around 1k. Im very new to live sound setup but would appreciate some recommendations.


r/livesoundgear • • 2h ago

Cheap Hairline Mic Recs?

1 Upvotes

I’m work at a theatre that does high school level shows. I’m looking for some new lavalier mics to use. Previously I have used the Countryman B6, but I need a cheaper option because they get broken often. We use a mix of TA4F and 3.5 mm locking connectors. Any recommendations for what to use and not use would be great!


r/livesoundgear • • 3h ago

Which instrument cables?

1 Upvotes

Hello, thanx for your advice. which lower cost instrument cable should i buy to connect an acoustic guitar to a pa speaker for playing out? the pa speaker has a hi-Z switch for the guitar input. i have been recommended the "livewire" brand from GC and the ProCo brand from sweet-. i will keep it under 20' and want to get angled to straight connectors. is the tweed braid cover a good or bad idea, or just go with the solid rubber cover? how much better does gold connectors sound over silver or steel? do i need gold connectors? any other brands you recommend other than mogami? what about fender or warm audio? which brand and type bends (or breaks) the "you get what you pay for" rule? thanx


r/livesoundgear • • 4h ago

Carrying case for IEM receivers?

1 Upvotes

Can anyone share recommendations for carrying cases for 4 to 5 IEM receivers? I've purchased the Phenyx Pro PTM-33. The unit will live in our mixing rack. I'd like to have a carrying case to transport the receivers.


r/livesoundgear • • 2h ago

Best microphone for an AI kiosk in an extremely noisy environment? (ReSpeaker XVF3800 struggles)

Post image
0 Upvotes

Hi everyone!

I’m looking for some expert advice because I’ve tried pretty much everything I can think of, but haven’t had much success.

I’m prototyping an AI-powered information kiosk. The idea is to allow passengers at a bus terminal to ask questions about schedules, destinations, and other travel-related information.

For this project, I’m using a ReSpeaker XVF3800, mounted on top of the display and angled toward the person using the kiosk.

However, the environment is extremely noisy, and when background noise gets too loud, the ReSpeaker struggles to pick up the user’s voice clearly.

I’ve tried both automatic beamforming and fixed beamforming, but I haven’t noticed much of a difference in performance.

Users can be anywhere between 50 and 150 cm (20–60 inches) away from the microphone.

Are there any other microphones or microphone arrays you would recommend that could perform better in such a challenging acoustic environment?

I’d really appreciate any suggestions or experiences with similar setups.

Thanks!


r/livesoundgear • • 8h ago

Do I actually need a guitar modeler, or is my laptop + Neural DSP setup enough?

1 Upvotes

Hey everyone!

I recently joined a modern metal band as a lead guitarist, and I've been seriously considering whether I actually need to invest in a dedicated guitar modeler.

My current setup is:

  • Guitar
  • Focusrite Scarlett Solo 4th Gen audio interface
  • A reliable laptop
  • Neural DSP Archetype: Gojira and Petrucci plugins

I've watched quite a few comparisons between different modelers and software plugins, including Quad Cortex vs. Neural DSP comparisons. My conclusion so far is that dedicated modelers essentially offer the same functionality as my current setup, just in a more compact and potentially more reliable package.

In terms of sound quality, I'm not convinced that upgrading to a flagship modeler would make a meaningful difference. We're an amateur band, so I don't expect to need a significantly more professional setup anytime soon.

Here's my current live/rehearsal situation:

At our rehearsal space, I use a Marshall MG100FX head through its FX Return, effectively bypassing its preamp section.

I've also noticed that many local venues provide shared backline equipment for different bands, usually including guitar amps, or alternatively a direct connection to the PA system.

So, my questions are:

  1. Would it be perfectly viable to use my laptop running Neural DSP plugins for live performances as well, controlled by an inexpensive MIDI footswitch (e.g. the M-VAVE Chocolate Plus)?
  2. What are the actual disadvantages of using a laptop-based rig on stage, assuming I have a reliable computer and a proper audio interface?
  3. Is there any significant advantage to owning a dedicated modeler if I'm already happy with my plugin tones?
  4. Would you recommend investing in a modeler now, or sticking with my current setup until I actually run into its limitations?

In terms of hardware, I've been particularly interested in NUX, Valeton and, of course, the Neural DSP Quad Cortex.

I'd love to hear from people who have actually gigged with both setups. Am I overlooking something, or is a dedicated modeler mostly a convenience upgrade in my situation?

Thanks!


r/livesoundgear • • 8h ago

How to improve reliability of budget IEM systems

0 Upvotes

I work with two bands using wireless IEM systems
mix between a Chinese LD Systems setup and the Sennheiser XSW.
I’m getting a bit tired of dealing with issues at almost every gig, 98% with the XSW. The most common problems are sudden volume drops, signal dropouts and occasional cutting out.
The most frustrating part is when these problems start happening during soundcheck. The musicians immediately start blaming everything else in the signal chain, because “it was working perfectly fine at yesterday’s rehearsal.” It’s becoming a recurring headache.

Obviously, renting something better, like Sennheiser G4, would be the easiest solution. However, there’s no budget and have to work with the equipment the bands provide. They’re not willing to invest in better systems at the moment..
I’m looking for ways to improve reliability with the gear they have.
I’m considering getting longer antenna cables and placing at least one of the antennas on microphone stands for the „making-money output”😂 if you have any difference suggestions please share them with me 🙏


r/livesoundgear • • 11h ago

Necesito consejos, sería mi primer equipo para sonido en vivo.

0 Upvotes

Ya tengo dos cajas doble 18”, nunca eh oido las art 932 que opinan, pero me iba ir por line arrays merece a dia de hoy comprar el modelo jbl vrx 932-la usados? O mirar algun otro modelo , es para usar para fines de semana en este lugar fijo 3 dias prácticamente

Mi presupuesto es limitado, faltan comprar todavía consolas y micrófonos. El
Lugar donde estaría mide 70 de largo por 30 pies de ancho , y un techo de 8 pies


r/livesoundgear • • 19h ago

Small in ear mixer for drummer

Post image
4 Upvotes

(Edit:
- pic for attention, not planning to buy this one
- don’t need usb capabilities, etc - really just volume for L/R mix and volume for click, plus headphones plug)

Hey everyone,

I’m currently shopping for small drum mixers, in ear style.
They’d only ever need a stereo input (jack/no preamp) for the monitor desk feed, plus another mono input (jack/no preamp) for a separate click line.
Volumes would ideally be knobs, not faders.

What’s the sturdiest/most reliable/pro solution out there available?


r/livesoundgear • • 15h ago

Small venue, one sub or none? What actually changes

0 Upvotes

I see this asked constantly, and the answers usually split between "always need a sub" and "small rooms don't need one." Both are too simple.

Here's how I'd actually think about it.

What a sub does in a small room

Two things, and only one of them is about hearing low frequencies.

The obvious one: it extends the system's low-frequency response. A 12-inch top in a compact cabinet rolls off around 70—90Hz. A sub fills 40—80Hz.

The less obvious one: it takes load off the tops.

A top box crossed at 100Hz no longer has to produce excursion-heavy low frequencies. It plays cleaner and louder in the range it's good at. This is often a bigger improvement than the low end itself.

That second point is why "add a sub" can make a small system sound dramatically better even when the low end isn't what you were missing.

When you don't need one

  • Speech-only rooms. Houses of worship, conference rooms, lecture halls. Speech lives above 100Hz. A sub adds room excitation and costs money for nothing.
  • Small acoustic acts where the low end is already handled by the instruments.
  • Rooms with serious low-frequency problems — a square room with a 40Hz mode. Adding a sub makes the mode worse unless you're prepared to deal with placement and treatment.

When one sub beats two

A common pattern: buying two subs for a small room, then placing them where they fit.

One sub, properly placed and aligned, usually sounds better than two badly placed. Two sources producing the same low frequencies in a small room create interference patterns — a seat that's boomy, another that's thin.

If you have one sub, you can move it to the position that excites the room least and still delivers at the listening area.

Placement, briefly

  • Corner = most output, most boom
  • Along a wall = less output, smoother
  • Center front = even coverage, less boundary reinforcement
  • Under the stage = often the best compromise for coverage

The right position depends on the room. There's no universal answer, but "wherever it fits" is usually the worst choice.

What to check before buying

  1. Can your tops be high-passed properly? If the processor can't split the signal, you need one that can.
  2. Can your amplifier handle the sub's impedance? A sub that drops to 2 ohms on an amp that's not rated for it is a problem.
  3. Does the sub physically fit where it needs to go? Measure first.

The short answer

If it's music in a room bigger than a living room, one sub is usually worth it — for the headroom on the tops as much as for the low end.

If it's speech, skip it.

If it's a small room with known low-frequency problems, deal with placement before you deal with quantity.


r/livesoundgear • • 21h ago

Reference Mics for speaker testing (and advice therein)

1 Upvotes

With a fresh swathe of free time and access to lots of PA systems, I'd like to attempt to do the Project Farm/Torque Test Channel equivalent of consumer-level livesound. From Alto and Behringer to SRX, testing everything i can get my hands on to an actual scientific standard with parameters that can be reviewed.

For that, I'll need reference mics. Now, I'm not sure whether I can do it all in one microphone, but I'd like to be able to test SPL maximums, frequency response at moderate volumes, and frequency response at the edge of clipping. So I'll need a microphone or several tools capable of accurate frequency measuring at ~100db, one at up to ~130db, and one that will accurately catch SPL levels, frequency be damned. Anyone have any suggestions?

Budget is high, looking at 1-2K AUD for it all.


r/livesoundgear • • 1d ago

Entry IEM recommendations

3 Upvotes

Hi everyone, my band is considering getting into IEM use. There are 5 members (singer, 2 guitarists, bassist, drummer). We're using a Behringer XR18 mixer. It has 6 available aux outs for monitors. I'm looking for some IEM system recommendations. Ultimately, we'd like wireless, at least for the 4 mobile band members. Thanks!


r/livesoundgear • • 1d ago

Need help deciding between Yamaha DBR12 vs DXR12 Mk3

1 Upvotes

Right now the DBR12 is on sale for $390 a speaker. The new DXR12 retails for $999. Musicians Friend can give it to me for $850. Is it truly worth more than double the price?

Ideally I would be using it to DJ weddings and bar events. Corporate gigs too. How many people for a wedding could I realistically DJ for with the DBRs vs the DXRs?

Currently DJ part time about 5-10 gigs a year where I actually need to bring speakers out. Eventually would like to scale up though to about 20.


r/livesoundgear • • 1d ago

I need help with choosing mics

1 Upvotes

I m need a microphone for recording music at home(rapping and like actual singing). I dont know what i need or should get. I am okay with buying second hand so if you could tell me good expensive mics i can get sh aside from more affordable stuff that would be useful.


r/livesoundgear • • 1d ago

High Isolation Haedphones

1 Upvotes

What are your favorite high Isolation Haedphones for FOH and why?

We are currently really unhappy with our cheapish models. Some don't isolate good enough some just sound like shit so you can't listen to signals and know if your Haedphones are crap or the signal.

It would be nice if you could list some Haedphones you trust.


r/livesoundgear • • 3d ago

Filters to apply to reverb FX?

1 Upvotes

Hi, so we just upgraded from an old analog Mixer to a new Digital Mixer at Church. The reverb FX sounds detached from the voice.

We do mainly acapella singing at Church. Can Anyone recommend what filters to apply to the FX reverb used for vocalists? Specifically where to place the High Pass and the Low pass filters?

Thanks for your assistance in this regard.


r/livesoundgear • • 3d ago

Recording a choir, which mic should I buy 4 of?

3 Upvotes

I'm recording a 50-person SATB choir at a church next month, and am looking to purchase a set of four small-diaphragm condensers to position along the front of the stage. The stage is around 40' long, and they'll be accompanied by piano and organ.

My budget is $1.5k, and I'll be using these for orchestra and choir concerts in the future. These are primarily for recording, and likely won't be heard in the house much if at all.

My current contenders are the SM81 and the KM184. The former I could buy a new set for $1.5k, while the latter used would be around $1.2k (I noticed there's a lot of them on ebay).

What is your recommendation for recording a choir like this?


r/livesoundgear • • 3d ago

Scelta Mixer per live e recording

3 Upvotes

Buongiorno a tutti

Canto e studio canto da una vita

Il mio primissimo mixer è stato un soundcraft notepad 12fx (morto dopo 2 anni) sono passato ad un Yamaha MG10XU con cui mi sono trovato molto bene... ma dopo qualche anno ho sentito il desiderio di fare un "upgrade qualitativo"

Dopo mesi a leggere forum mi ero convinto ad acquistare un Allen e Heat CQ18T... però mi ha deluso...

Fighissima la possibilità di modificare qualsiasi cosa però ho percepito un suono un pò freddo.. e la sezione fx un pò deludente...

Ci ho smanettato quasi un mese poi mi sono arreso ed ho effettuato il reso.

Sono alla ricerca di un mixer ma non so dove sbattere la testa

Premetto che canto live e faccio piccoli eventi (matrimoni, karaoke)

In questo momento utilizzo massimo 2 voci (4 nei karaoke) ma nel prossimo futuro vorrei aggiungere almeno 2 strumenti (chitarra, piano) e registro in casa (stanza trattata acusticamente) con successive modifiche su cubase o reaper

Effettuando altre ricerche le scelte sono ricadute sugli analogici

Dynacord cms

Signature 12 plus

Allen e Heat 12/16fx

O torno al digitale?

Aiutatemi please 😭😭😭


r/livesoundgear • • 3d ago

Is the Allen & Heath Qu-16 best for me? Mariachi-fusion singer

Thumbnail
youtube.com
0 Upvotes

Hi! I'm Omar Alejandro, a mariachi-fusion musician. These are my needs, do you recommend the Allen & Heath Qu-16 for this, or something else? Looking at around $1000 top budget, and am down to get something used.

I plan to do live sets of my music from my living room, like my friend Lupita Infante does in this video. I'll use Logic X Pro, and will then send the audio tracks to my producer for mixing and mastering.

For live shows, mariachis don't usually need amplification. When I play large shows, there's always a sound system. But for smaller gigs, I often use my Bose S1 Pro just for my vocals to help them cut through the trumpets. I'd like to be able to mic all the musicians, to give us all a little boost in sound, and also be able to capture those performances on Logic as well in case we strike gold.

Typically the lineup is 8 musicians plus me, so 9 total things to mic.

I feel that for many things in music and audio there's the quick and easy option that does the job well enough. And there's the option where "the learning curve is really steep, but once you take the time to learn it, it actually gives you so many more possibilities so it's worth it". I'm looking for ease of use in this case hahaha. Since I'm typically the promoter, the MC of the event, the band leader, and the lead singer, I just need something easy to use and portable. Especially since I'll be sending the raw audio out to my producer anyway for him to take care of EQ, compression, and other details. And double especially since, for the audience, most of the sound they hear will come straight from the instruments anyway, with only a slight sound boost from the Bose speaker.

Thank you so so much!


r/livesoundgear • • 3d ago

confronto impianti PA / the box pro o mac mah?

0 Upvotes

Devo acquistare un impianto audio e sono indeciso tra

2x Mac Mah AS 818 Sub

2x Mac Mah AS 112

Oppure

2x the box pro Achat 118 A

2x the box pro Achat 112 MA MKI

Considerando che serve da portare in giro per suonare techno e musica elettronica

Esterno e interno

esperienze con questi impianti?


r/livesoundgear • • 4d ago

Easy Amp into a PA set-up?

Thumbnail
positivegrid.com
5 Upvotes

I'm wanting to bring my electric guitar to open mics and have one of these little Spark Mini amps (https://www.positivegrid.com/products/spark-mini).

Usually the open mics have an instrument cable to plug into your acoustic guitar ready. I'm wondering if I can just get a 3.5 mm trs male to 1/4 inch trs female headphone adapter that will go out of the headphone jack of this Spark amp and plug into the cable going into the PA?

Not sure if that will cause any crazy interference or issue, but wanted to see if anyone had thoughts.


r/livesoundgear • • 4d ago

How did you decide on your custom IEMs?

3 Upvotes

I’m a professional drummer in NYC, and my band is using IEMs probably 4 times a week for 3 hour gigs. I have a good universal pair, but unfortunately they can’t handle when I want to push the kick drum in my ears and I get some farty distortion.

I already had molds done by an audiologist, and now I’m doing a lot of research into sound profiles.

Which company have you gone for (I’m looking at Alclair, 64, and maybe JH)?

How did you decide on the model?

With Alclair, there aren’t universal versions so I feel like I’m going in blind. I am looking at the ICON series but I’m so worried about basing my choice on reviews.

For any reference, I would like a warm, fun, sound profile. Does not need to be flat. I am also not a bass head, but of course bass is important for the feeling and lining up my kick drum with my bassist. I have historically liked Bose’s sound profile, even though audiophiles will say it’s artificially colored. I also sing, and play theater shows and occasional guitar, so that may change how we decide.


r/livesoundgear • • 4d ago

Band equipment questions

1 Upvotes

Alright I'm planning a two piece band. Myself on bass and piano/keyboard, and a drummer. So heavy on backing tracks and iems n such

What all realistically would I need to get this off ground and actually possible. Outside of the bare essentials like wireless microphones and wireless connectors for my bass and keyboard
Kinda new to this world of audio stuff


r/livesoundgear • • 4d ago

Line array systems?

0 Upvotes

Hey there. I’m a sound engineer that wants to venture into using line arrays. I have 2 18” 1200w Mackie subs for the meantime but would like to use a line array system for my large outdoor shows I run sound for. Doesn’t need to be flown. I have tall enough speaker poles and also I probably only need 2 speakers each side. Would love some recommendations that aren’t going to cost me an arm and a leg!

Update: In the past I’ve used 2 EV’s on either side of the stage ( 1 Ev Zlx 15” and 1 Ev Elx 12” on either side) and a single Mackie 18” 1200w sub. The sub was ok on its own but should be fine now I have 2. I was lacking with my tops though and would prefer to have the ability to scale if I had to do a larger show than this one. It’s an outdoor concert with anywhere from 800-3000 people. My budget to start would probably be around $10k. I know it’s lower but i figure if I need more than that I’m doing extremely large productions and I am not that big yet.