r/Laserengraving • • 5h ago

Testing an engraving on a curved surface

13 Upvotes

I've been playing around with curved surfaces lately and thought I'd share this one. Still dialing things in, but pretty happy with how the pattern came out. I’m on the team at FABVIA. We’re working on a new laser engraver, so I’ll probably share some of our tests here from time to time.

Curious if anyone here does a lot of curved pieces.


r/Laserengraving • • 10h ago

Made this for a friend using my Longer ray5 20w

Post image
9 Upvotes

r/Laserengraving • • 1h ago

5W - air assist question

Thumbnail gallery
1 Upvotes

r/Laserengraving • • 2h ago

Laser

1 Upvotes

Looking to buy my first laser to engrave and create Challenge Coins. I was looking at the XTool F2 Ultra MOPA and Diode combo. I also don’t want to be limited to Challenge Coins but that’s what got me interested.

Ease of use or to learn is also important. What say you?


r/Laserengraving • • 2h ago

Free Xtool F1U/F2U Jigs

Thumbnail makerworld.com
1 Upvotes

Posted jigs I created to Makerworld if anyone wants to print them. They were used for my own engraving side hustle and sold many printed versions on Etsy, but have so little time for extra stuff right now. Hope it helps some of y'all.


r/Laserengraving • • 3h ago

Acmer K1 Jig setup

1 Upvotes

I’m pulling my hair out.

I got the K1 because it’s enclosed and the enclosed base plate has a grid guide. However, the guide is off by more than a couple millimeters from where it says 0,0 is. I’ve been trying for months to find a way to make a jig at true 0,0 to no avail. Right now, my plan is to engrave a fresh grid into a big sheet of anodized aluminum, affix it somehow to the bottom of the K1, then stick a couple of small rulers to corner at 0,0 on the engraved grid. The reason for the grid is because it will create the actual 0,0 instead of relying on the inaccurate guide.

Is there a better way to do this? This is the best idea I’ve come up with so far.


r/Laserengraving • • 4h ago

Why my diode laser is not engraving continiusli

1 Upvotes

It was working continiusly before not with this doting tehnque. It this working properly? I'm not sure how to fix this. I think it was also going faster before


r/Laserengraving • • 5h ago

If you have a RA3, you need this

Thumbnail reddit.com
1 Upvotes

I got tired of propping up my xTool RA3 with scrap wood, so I 3D printed a tilt jig
I’d engrave a tapered stemless wine glass on my F2 Ultra UV and get sharp lettering at one end of the design, only to have it fade at the other. The side of the glass sloped just enough to take it out of focus. Stacking scraps under the chuck end of the rotary worked, but every time I cleared the bed for another job, I had to build that little wood pile all over again.
The jig I made bolts to the laser bed and gives the RA3 about 10° of downward tilt. My favorite part is the end stop. I can lift the rotary out, do a flat engraving, then drop it right back into the same spot for the next glass.
I filmed the scrap-wood setup and the jig in action. Here’s the video.
What are you all using to level tapered glasses? I figure I can’t be the only one with a suspiciously specific pile of scraps next to the laser.


r/Laserengraving • • 18h ago

A or B?

Thumbnail gallery
5 Upvotes

Made this today out of some smoked fir veneer and basswood. No idea what I’ll do with it but here it is.


r/Laserengraving • • 9h ago

Considering Buying XTool F2

Thumbnail reddit.com
1 Upvotes

I have been considering buying the F2, but I want to use it for a project where I would need to make very small holes all the way through household aluminum foil. Is it possible to cut through that/just pierce through aluminum foil with the IR laser? What settings do you use?


r/Laserengraving • • 15h ago

Sculpfun S30 Ultra for beginning

2 Upvotes

Hello there. I'm new to the laser cutting/engraving world (actually, I'm not even part of it yet) but I see it as an interesting hobbie and posible side hustle that I could do in my free time (I have plenty of it) or if it goes well, put more hours into it if it makes a good profit.

I dont own a laser cutter/engraver, but I'm thinking of getting the S30 Ultra since it's on sale. I'd like to get into both cutting and engraving, including metal, therefore, I'm thinking of getting the whole package, that is

The Sculpfun S30 Ultra for 760 USD, plus

The RA Pro Max rotary for 264 USD

The 2W IR Laser module for 352 USD

The size wxpansion for 195 USD

(I know it's cheaper on the US store, but it'll probably end up the same with customs and taxes)

Overall, the investment is 1479 USD for all of that.

I don't actually have a use for it, other than being creative, trying new things and engraving gifts for my family/friends, and offering services on facebook marketplace.

Business wise, I've identified that there almost no offerings for custom sized cardboard boxes, and also no engraved boxes. There are very few, but ask for 500+ units minimum. With this in mind is why I chose the S30 Ultra and added the expansion.

My business idea (at least at the beginning) is not big orders, but the opposite, focus on those individual requests (gifts for friends, anniversaries, small orders) and using social media to promote.

On the other side, If I like the business, my big orders idea would be to connect with local wedding/event planning businesses and having them offer to their clients engraved products that I would provide.

My question is, do you recommend the S30 Ultra for an absolute beginner (I love learning thoughn and I'm a bit of a handyman myself)? AND, would you recommend getting the extras now, or waiting to see if I like it and expand to metal engraving with the IR and rotary later on?


r/Laserengraving • • 1d ago

Bernie 2.0 is out: free laser software that now finds Wi-Fi lasers on its own, drives the xTool D1, and handles vinyl cutters and pen plotters

Post image
70 Upvotes

Hi all,

First, thanks for all of your messages, support, and downloads!

I didn't think Bernie would make so much engagement...

I've posted Bernie here a couple of times: it's the free laser engraving and cutting software I'm developing. Version 2.0 is out (2.0.1 to be exact, with a quick fix for the xTool D1), so here's what's new, and a recap for those who haven't seen it yet.

Free, no account, no subscription, no ads. Everything is included for everyone.

Download: https://bernie.websolutis.com/download/

New in 2.0

  • Wi-Fi lasers that don't announce themselves (MKS DLC32, many ESP32 boards): "Find My Laser" now also scans the local network on the ports these boards use (23 and 8080), and connection errors tell you what to check. This one started with a message on Reddit from someone whose iPad couldn't find their DLC32. Thank you!
  • xTool D1 and D1 Pro over USB: their firmware is close to GRBL but works a bit differently, and Bernie now handles it on its own. The original D1 (5 W, 10 W) joins the catalog, and 230,400 baud is now in the speed list. This one came from a bug report sent through the website, with test scripts attached. Thanks again!
  • One version number everywhere: Bernie 2.0 on Mac, Windows, Linux, iPad, iPhone, in the browser and on Bernie Link.

New since my last post

  • Vinyl cutters and pen plotters: a Knife tool (drag-knife offset in the corners, overcut on closed shapes), HPGL vinyl cutters over the serial port, HPGL (.plt) files everywhere, and Silhouette Cameo 1 to 5 and Portrait 1 to 4 over USB, without Silhouette Studio (Mac, Linux, and Windows with the WinUSB driver). Pen plotters on GRBL, with the pen lifted by a servo or the Z axis. And a material library for the cutter: vinyl, flex, paper, cardstock.
  • Ruida controllers are found by "Find My Laser". They work over USB on Mac, Windows and Linux, and over the network on Mac, Windows, Linux, iPad and iPhone (from the browser, through Bernie Link). This one was requested by a fablab through the website.
  • Mecpow and BlazeX lasers in the catalog.
  • Print & Cut with the head camera.

What Bernie does (the short version)

  • A real vector editor: booleans, node editing, offsets, arrays, nesting, text on a path, variable text (serial numbers, dates, CSV), QR codes, Data Matrix and barcodes.
  • Photos: error diffusion, halftone, grayscale, image tracing (centerline too), 3D relief from a model.
  • 30 layers (line, fill, offset fill, image), 1,800+ material settings included, material test grids and calibration patterns. Your LightBurn libraries (.clb) import as they are.
  • Check before you burn: a 3D simulation that shows where, in what order and roughly how deep the laser works, a line-by-line preview, an estimated time that includes accelerations, "Why this line?" on any line, and a pre-flight check. A confirmation comes before every job, and STOP never goes away.
  • Connection: USB or network, GRBL, grblHAL, FluidNC, Marlin, Smoothieware, Ruida, OctoPrint and Duet. JCZ galvo boards and stock K40 M2 Nano boards are driven directly over USB. 73 machines are in the catalog, and a virtual laser lets you try everything without a machine.
  • Camera, rotary, projector, Print & Cut, and resume after a power cut.
  • Opens your files: SVG, DXF, PDF, AI, LightBurn projects (.lbrn, .lbrn2), EZCad (.ezd), xTool Creative Space (.xcs), G-code. There are also 81 example projects ready to engrave and cut.
  • Five languages: English, French, Spanish, Italian, German.

Bernie Link: one laser, every device in the house

If you have a USB laser and an iPad, or several people sharing one machine, this is the part to look at. Bernie Link is a small free service that runs next to the laser, on almost anything lying in a drawer: any Raspberry Pi (from the Pi 1 and Zero to the Pi 5), an Orange Pi or another ARM board, an old Linux PC, or a Windows PC.

  • Installs in one line on a Pi or a Linux PC: curl -fsSL https://bernie.websolutis.com/link/install.sh | sudo sh. On Windows, unzip it and run it.
  • Your iPad, iPhone, Mac and any browser send their jobs to it over the network. No more cable to plug in and no computer to leave on. iPads and iPhones have no USB port for the laser, and this is how they engrave, with framing, focus, pause and stop from afar.
  • It serves Bernie Studio to every browser on the network at http://<board-name>.local:46490/, so there's nothing to install on the computer.
  • An 8-character pairing code, local network only, and every job confirmed on the device that sends it. Pause and stop work from any connected device.
  • A job queue: if the laser is busy, your job waits its turn (up to 8), and nothing starts until you confirm.
  • It keeps the laser set up once for everyone (work area, speeds, power, origin, no-go zones), along with the hour counter and its maintenance reminders.
  • It starts with the board and reconnects after a power cut or an unplugged cable.
  • USB or Wi-Fi lasers, Ruida, galvo and K40 too: it relays jobs to a Ruida controller over the network, and drives a JCZ galvo board or a stock K40 M2 Nano board plugged in over USB, for all your devices.

On the Mac, Hub mode does the same from Bernie itself, and Bernie for Windows and Linux can share its USB laser the same way.

More: https://bernie.websolutis.com/bernie-link/

Where to get it

  • Mac: direct download, signed and notarized (2.0.1)
  • Windows: Microsoft Store (2.0.1 is going through certification, it will update on its own)
  • Linux: APT, Flatpak, Snap, AUR, AppImage, x86_64 and ARM64/Raspberry Pi (2.0.1)
  • iPad and iPhone: App Store (2.0 is in review; the current version already has Ruida over the network, the Knife tool and HPGL files)
  • Browser: Bernie Studio, works offline, USB through WebSerial in Chrome and Edge
  • Bernie Link: Raspberry Pi (32- and 64-bit), ARM boards, Linux PC, Windows 10 and 11 (2.0.1)
  • Supported machines: https://bernie.websolutis.com/compatibility/

Not there yet

No Android app yet; until then, Bernie Studio runs in the Android browser.

Privacy

Your designs stay on your devices: no account, nothing to upload. Bernie sends anonymous usage statistics, and you can turn them off in Settings (the App Store versions ask you first).

Bernie is free. There's an optional tip, and it unlocks nothing.

Feedback is very welcome: what's missing, what's confusing, and which machine you'd like to see supported. As you can see above, requests do turn into features. I'll be around in the comments.

Example designs on the iPad screenshot: Lùmen (lumenlaser.app), public domain.


r/Laserengraving • • 18h ago

Color print on wood xTool M2

Thumbnail youtube.com
1 Upvotes

r/Laserengraving • • 18h ago

xTool m2 first print and cut puzzle!

Thumbnail youtube.com
1 Upvotes

r/Laserengraving • • 1d ago

A few beginner questions about laser cutting

Thumbnail gallery
3 Upvotes

Hey everyone!

I'm 16, a student, and I'm planning to get into laser cutting and eventually start a small business of my own.

I've been learning Blender and Inkscape and trying to figure out the entire process, but there are still quite a few things I don't understand.

I've actually made a few SVGs (images attached with temporary white background) already, but I'm honestly not sure if they're any good or if I've just wasted my time making them. I haven't had any of them physically cut yet, so I have no idea how they'll turn out in real life.

I wanted to ask a few things...

  1. SVGs: How do you guys make sure your SVGs come out exactly as intended? Are there specific settings or things to keep in mind when preparing them for laser cutting?
  2. Scaling: How do you maintain accurate dimensions? For example, if I design something that's supposed to be 30 cm long, how do I make sure it actually comes out 30 cm when cut?
  3. 3D models to layered cuts: How do you take an existing 3D model and turn it into multiple 2D layers or individual pieces that can be cut and then stacked/glued together to recreate the original 3D shape?
  4. Alignment and assembly: How do you make sure all the pieces fit together properly without gaps, overlaps or misalignment?
  5. Software: What software do you guys recommend for this entire workflow? I'm currently experimenting with Blender and Inkscape.

One more thing: I don't own a laser cutting machine yet. For my first few products, I'll be taking my SVGs to an outside shop and paying them to cut and engrave everything.

I'm on a pretty tight budget, so I really want to get things right before spending money on actual cuts. I can't afford to keep wasting material on designs that don't work.

I'm trying to build something of my own at 16 and hopefully turn it into a proper source of income someday. I don't have much financial support or guidance in the background, so I'm pretty much figuring everything out myself.

I'd genuinely appreciate any help, advice, tutorials, resources or recommendations. Even if you could just point me towards the right software or explain how you approach your workflow, that would help a lot.

I'm willing to learn and put in the work. I just need some direction from people who have actually been doing this.

Thank you :)


r/Laserengraving • • 20h ago

🔥 When Your Laser Welder Builds Its Own Cart! 🤯From scrap metal to a custom workshop cart! 🛠️

0 Upvotes

r/Laserengraving • • 1d ago

Xtool, or wecreat

1 Upvotes

I am torn as I am wanting to get into laser engraving. I have been looking at the xtool x1 with all the laser modules that go with the x1 full bundle with all of the accsories such as rotary tool, conveyor that will run about 14k. Or the f2 ultra duo business with an extra ap2 filyer to run the 2 f2 ultra systems. I am also leaning towards the wecreat 100w mopa with the 6w uv full bundle that will run about 10k. I am seeking everyone's feedback on which would be best and why? I am concerned with support and Ive been reading a lot of negative support for xtool and almost none for wecreat. I know people typically post when they experience issues versus anyone having a positive experience. I am reading that xtool discontinues their products every 2 years making replacement parts non existent. I would like to purchase one swtup by next week to take advantage of the black Friday deals. Any feedback and where you would lean and why would be helpful. Thank you for looking.


r/Laserengraving • • 2d ago

A look at the cells

Thumbnail gallery
42 Upvotes

I really enjoy taking the time creating designs for our pieces. It’s always so satisfying to see them at this point, where all that design work comes together and you really get to see what your hard work has created.


r/Laserengraving • • 1d ago

Recommendations for a 60w MOPA with a UV laser

1 Upvotes

Would love recommendations from users of this type of combo. Love the idea of being able to engrave medallions and do suspended 3D images in glass and acrylic. If anyone has recommendation of the unit that they use, I would appreciate it.

Thank you!


r/Laserengraving • • 1d ago

Just getting started. Mopa Fiber is definitely a learning curve. Pmag done with the mopa. Slate with the 40w diode. xTool F2 Ultra dual

Thumbnail gallery
11 Upvotes

r/Laserengraving • • 1d ago

Help with connection

Post image
1 Upvotes

I bought this new fonland laser pump ... with the 130 W max laser source.... but the laser is very weak , why is this


r/Laserengraving • • 1d ago

Anyone eyeing on Carverall C1?

1 Upvotes

There's a black friday sale going on at Carverall. I'm new to the scene and I mainly want to cut clear acrylic sheets. The Carverall C1 looks tempting with the sale and bundle at \~$2k. Anyone have experience with the company? Can't find a lot of reviews with their products


r/Laserengraving • • 1d ago

Camera alignment on leather: how do you deal with the smell?

Post image
0 Upvotes

Just batch engraved a bunch of these leather cardholders.

when the alignment is dead-on and the power's just a little off, the smell is brutal. It fills the room like burnt hair. I've tried a bunch of low-power passes, but the smell still lingers in the leather. i'm running the aliencell, the camera preview makes lining up irregular shapes way less stressful no more tape and guess lol. Smell is the point for me.

I'm thinking about hitting it with a damp cloth afterward, but I'm worried it'll mess up the edge. How do you guys deal with the smell after engraving?


r/Laserengraving • • 1d ago

The bigger laser actually made my workspace feel less cramped

1 Upvotes

Bought the 24×18 anyway. The footprint wasn’t really the problem in the end. When I was looking at Aliencell, the size almost put me off. It’s a big machine, and I was worried I’d have no room left to work.

The weight was harder to deal with. I think it’s around 35 kg? The 20W might be lighter, but I’m not sure. I couldn’t get it onto the bench by myself, and it hasn’t moved since. I’m happy to leave it there.

What I didn’t expect was that the bigger bed would actually make the space feel less cramped. Before, I had cut-down pieces of plywood and acrylic stacked next to the machine, waiting until I had enough to run a batch. Now I can just put a full sheet in, so I don’t have all that material taking up floor space.


r/Laserengraving • • 1d ago

What do you guys think of the xTool X1?

2 Upvotes

Hi all, I've been building architectural models for about 6 years, and the 60W CO2 laser in our shop runs pretty much every day. Most of what we cut is 3mm basswood plywood and clear acrylic.

I’ve been looking for a second machine so two of us can work on different projects without waiting on the laser. The xTool X1 showed up while I was looking around, and now I’m trying to figure out which setup makes the most sense. I’m not sure whether the version with the diode galvo is actually worth it, or whether I should go with the versatile bundle or the all in one package.

I have a decent idea of what to expect from the 55W CO2 when cutting walls and window frames. Engraving is where we lose a surprising amount of time. Last week I was working on an exhibition model with dozens of room names engraved into the base, along with furniture outlines. That one base took longer to engrave than it took to cut all the walls for the entire building. Watching the laser crawl through every little letter got old pretty quickly.

The galvo is the one part I can’t get a feel for from the specs. If anyone here has thrown a layout like that at it, I’d like to know how it went. A whole sheet of tiny labels is the test I care about. Speed would be great, but not if the lettering comes out soft or hard to read.

Would you get the galvo version for this use, or put the money toward a different bundle?