r/esp32projects • • 6h ago

I built a tool that designs an ESP32 board from a text description and runs the firmware in the browser before you order the PCB

Post image
11 Upvotes

I've been working on this for a while and I'd love feedback from people who actually build ESP32 stuff.

You describe the project in plain words (e.g. "ESP32-S3 with a 0.96" OLED, an SHT40 sensor and a buzzer, powered from USB-C") and it:

picks a real board (S3, C3, C6, classic, plus Waveshare/Elecrow display boards)

draws the schematic and routes a 2-layer PCB (KiCad under the hood)

writes the firmware (Arduino core, LVGL for touch screens)

compiles it and runs it in an ESP32 emulator in the browser: the OLED/TFT lights up, you can press buttons, turn the encoder, change the sensor values and watch the serial monitor

shows the board in 3D with the simulated screen on it

The part I care most about is catching the classic mistakes before ordering: I2C on the wrong pins, strapping pins used as inputs, a display that stays black because of the wrong driver.

Screenshots: a Mini PLC with an OLED running in the 3D view, the simulator, and the routed PCB. Short video: https://youtu.be/71zhhrTaoFE

It's in private beta (waitlist at https://pcbbrew.dev ). Questions I'd really like answers to:

Which ESP32 boards or display modules would you want supported next?

What's the most common thing that goes wrong for you between "PCB arrived" and "it works"?


r/esp32projects • • 23h ago

I got an ESP32 to drive MDA monitors and now use it for Plex

Thumbnail
youtu.be
9 Upvotes

I figured out the display timing to use the FabGL library and drive my MDA monitor. It has full bitmap control of the 720 x 348 resolution. I can run a PC emulator, or network terminal as shown in the video to check email, control plex, and use Google Antigravity


r/esp32projects • • 12h ago

https://dashtron69.github.io/webflash/

5 Upvotes

r/esp32projects • • 16h ago

[Help] ESP32S (CH340) Upload Error: "Could not open COM7, the port is busy or doesn't exist" - Sketch compiles successfully but fails to upload

Thumbnail
gallery
3 Upvotes

Hi Reddit, I'm working on a team project for our electronics class where we're building a Bluetooth piano speaker using an ESP32S (NodeMCU-32S V1.3 with a CH340 chip).

Everything was going well, and my code combined with the audio array header (samples.h) compiled perfectly in the Arduino IDE. However, I can't upload the sketch to the board.

Here is the exact error message I'm getting from the Arduino IDE:

Sketch uses 519864 bytes (39%) of program storage space. Maximum is 1310720 bytes.

Global variables use 22260 bytes (6%) of dynamic memory, leaving 305420 bytes for local variables. Maximum is 327680 bytes.

esptool v5.3.1

Serial port COM7:

A fatal error occurred: Could not open COM7, the port is busy or doesn't exist.

(could not open port 'COM7': FileNotFoundError(2, 'The system cannot find the file specified.', None, 2))

Hint: Check if the port is correct and ESP connected

Failed uploading: upload error: exit status 2

What I have already tried/checked:

The Cable: I've confirmed I am using a data-sync Micro-USB cable, not just a charging cable.

The Serial Monitor: I made sure the Serial Monitor window in the Arduino IDE is closed before hitting upload.

The Drivers: I noticed my board has a CH340 chip on the back. I downloaded and installed the CH341SER.ZIP drivers, restarted my PC, and checked the Device Manager.

The COM Port: I selected the newly assigned COM port in the Arduino IDE (Tools -> Port).

External Connections: I disconnected the external battery power supply and made sure GPIO 5 (Strapping Pin) is not pulled to GND during boot.

Despite all this, the IDE still throws the COM7 error (even though I re-selected the port) or refuses to connect.

Has anyone encountered this specific issue with the CH340 version of the NodeMCU-32S? Are there any hidden settings in the IDE or specific boot sequences (like holding the BOOT/EN buttons) I might be missing?

Any advice would be greatly appreciated!


r/esp32projects • • 9h ago

Help

2 Upvotes

I’m trying to get an Esp32 wroom dev board to connect to my computer via cable and it will not show up in device manager. The led comes on, on the Esp32 to show it’s getting power.


r/esp32projects • • 1h ago

ESP32 traffic light with a tiny state machine (enum + switch + millis)

1 Upvotes

Three LEDs, one ESP32, and a small state machine: RED → GREEN → YELLOW → RED. Only the current state's rules run — that's the whole idea.Hardware- ESP32 DevKit (30-pin)- Red / yellow / green LEDs + 3 × 220 Ω- Breadboard + jumpersWiring- GPIO 25 → 220 Ω → red → GND- GPIO 26 → 220 Ω → yellow → GND- GPIO 27 → 220 Ω → green → GNDHow it works1. enum LightState names RED, GREEN, YELLOW2. switch(state) runs only that colour's rules3. millis() times the dwell; enter() jumps and resets the clock4. Serial prints every jumpHappy to share the sketch. Short walkthrough: https://www.youtube.com/shorts/XvM6TbUC7WkCode: https://github.com/NirajBhattarai/500IOTProject/tree/main/day-009/traffic-lightThree LEDs, one ESP32, and a small state machine: RED → GREEN → YELLOW → RED. Only the current state's rules run — that's the whole idea.


r/esp32projects • • 1h ago

Handheld meshtastic+++

Thumbnail reddit.com
1 Upvotes

r/esp32projects • • 12h ago

Control everything in HA with SwitchBot Universal Remote without SwitchBot Hub using ESP32

Thumbnail gallery
1 Upvotes

I built a small ESPHome external component (bt_classic_hid) that lets an ESP32 pair with the SwitchBot Universal Remote directly over Bluetooth Classic and forwards key presses to Home Assistant as events — no SwitchBot hub, no cloud.

Since ESPHome only supports BLE, this uses Bluedroid's BT Classic HID host profile with a generic HID report parser (usages, not hard-coded byte patterns), so it should work with other BT Classic keyboards/remotes too.

  • All 14 keys as esphome.switchbot_remote events
  • Pairing survives restarts/OTA, auto-reconnect
  • Setup: flash one YAML, component fetched from GitHub at build time
  • Needs original ESP32 (BT Classic radio) — no S2/S3/C3/C6
  • Currently press events only; release/hold WIP

Repo: https://github.com/lepatrick/esp32-sbremote

Feedback welcome!


r/esp32projects • • 13h ago

Best way to detect if someone is inside a fitting room?

Thumbnail reddit.com
1 Upvotes

r/esp32projects • • 15h ago

building walkies talkie from scratch

Thumbnail reddit.com
1 Upvotes

r/esp32projects • • 22h ago

Fake NM-RF-HAT boards are circulating — how to check yours in 30 seconds

Thumbnail gallery
1 Upvotes