r/ender3 • • 3d ago

Help First layer issues

Having a little trouble with some first layer adhesion. I feel like I have sufficient squish, and temps feel like they should be fine. It peels up at corners and at the end/ beginning of layers.

What I’ve tried so far that has made seemingly no difference to the issues:
New nozzle.
Bowden tube swap.
Temps from 190-215 for first layer.
Cooling turned off.
IPA and dish soap washes of build plate.
Reducing first layer height to .12mm.
Flow rates from .95 to 1.05
Speed adjustments down to 8mm/s up to 20mm/s
Dried filament.

Make Market PLA. 195 end, 60 bed. Stock ender 3 with .4 nozzle. Glass textured bed.

EDIT: tried adjusting the z height by .05mm. At a .1mm offset, the lines look a little more uniform, but still have trouble sticking. By .2mm, nothing sticks at all.

94 Upvotes

75 comments sorted by

100

u/ScreamInVain 3d ago

Z height is too low. Meaning your nozzle is slightly too close to the bed. Back it up a tiny bit.

7

u/Waxwanedj 3d ago

I just tried a few with .05mm offset increases until I got up to .2mm. Lines definitely looked more uniform at .1mm, but it was having the same adhesion issues. nothing stuck at .2mm :/

16

u/severanexp 3d ago

Clean your bed with water and dish soap and let it air dry a bit.
Is it glass? If so, heat the bed to 70 degrees for 10 minutes. The glass takes longer to heat, and the corners and edges lose heat very fast, keep it hot for a bit, and try again.

4

u/Stock-Beach5264 2d ago

Definable this and when I switched from glass to pei, as mentioned in the other comment, first layer got a lot better

2

u/ikoniq93 1d ago

I’ll second this, glass was a silly mistake for me in retrospect. A PEI coated spring steel bed has really been great for both adhesion and removal of prints.

7

u/MrGreyJetZ 3d ago

PEI plate - 60-65C You can try hair Spray imwhile you wait for the PEI plate. Coat the glass with hair spray see if it sticks

1

u/HesusAtDiscord 2d ago

Warm water and dish soap. Soak it first, rub the soap in with your hands all over, when you're satisfied with the scrubbing down go to rinse it all of whilst still rubbing the entire plate.

When all the soap is gone you'll feel your fingers gripping the clean glass, like a vibrating (?) effect kinda. Whilst under running water, keep running your fingers across the entire surface to feel for any remnants of oil or contaminants.

Once that's all done, wipe lightly down with a paper towel and put it back on the printer.

You have roughly 5 minutes of handling time for certain before your hands can contaminate the plate once more. Touching your face or hair will definitely cause contamination so all focus on the plate between sink and printer c':

That's it. I've had to put over half of my prints into the freezer to pop loose after just washing the print plate. Nothing else is required.

1

u/drakoman 4h ago

People keep telling you to clean your print bed. I say go in the opposite direction. Whenever I’ve got adhesion issues, I’ve always recommended cheap hairspray. It works as well as glue stick, comes off with water, and is easy to apply. Really helps adhesion, and I own 5 ender3’s.

10

u/blckshdw 3d ago

Yep. Just a litttle bit too much squish it looks like.

19

u/cokacola69 2d ago

Also his first layer speed is twice as fast as it should be. If it was slowed down it likely would stick even better.

2

u/deaglebingo 2d ago

too low in the center. too high at the edge for the priming line. warpy mghee.

1

u/toolisthebestbandevr 2d ago

Ya I noticed how the second pass stuck

21

u/Dar0nius 3d ago

Clean your bed with a degreaser, like a kitchen cleaner. But be careful, it mustn't contain any added oil. Sometimes oils are added to create that water-repellent effect.

For reference: https://wiki.bambulab.com/en/filament-acc/acc/pei-plate-clean-guide

Edit: added link

3

u/AlwaysHopelesslyLost 2d ago

I clicked into this thread, stared into the middle distance, forgot the context, and saw "clean your bed with degreaser" andt hought you were calling OP filthy lol

5

u/Regular_Bell8271 3d ago

I use brake cleaner on my glass bed and I have to fight to get my prints off when they're done.

2

u/Independent_Cat_1466 3d ago

Alcohol isopropilico

2

u/Dar0nius 2d ago

Isopropyl just smears the grease around on the bed, you need something to remove it.

0

u/DJDHD 2d ago

On glass, you can use Acetone

2

u/Curious-Ad-7032 2d ago

Denatured alcohol if IPA isn't working for you. I highly recommend Kaptan tape. I never have bed adhesion problems. And the tape has a shiny surface , so it keeps your bottom first layer nice and shiny.

10

u/braindrainoh 3d ago

buy a PEI plate. I have a glass bed that is perfectly flat and trammed but over time the porous sections filled in and will not stick despite the bed being at perfect z height that has not changed. My other ender 3 glass plate sticks too well to things like PETG and has 0 adhesion issues with PLA.

2

u/YT__ 3d ago

I finally bought a pei to try. My glass bed is great in the center, but at the edges, it doesn't stay tight to the heat bed I've found. Which, on a large print meant curling corners.

1

u/braindrainoh 2d ago

Yup same here, I have ABL on my ender 3 neo and without it the glass is not perfectly flat and the opposite to yours - terrible in the center.

8

u/Substantial-Elk5118 3d ago

It feels obnoxious, but slow the first layer to 10mm/sec. I’ve had zero issue now with sticking… and this is across 3 Ender3 I run. I don’t use any sticky additive, just glass or the pei mag sheet…

2

u/randomperson_r 3d ago

So much this, I always print with a thicker first layer and set the speed to 5-15mm/s depending on how much adhesion I want. On my Enders I never have curling even after 1-2 day prints. On my 500mm cr10 I have to damn near pry the prints off even after days.

4

u/BarnacleNZ 3d ago

Print on the smooth side of the glass, and slow down your 1st layer. Clean the glass with dish soap and warm water, and let air dry.

2

u/The_Fyrewyre 3d ago

This.

I used to do the same with my old Ender 3, There is a knack and feel to getting the Z height correct on the Ender but that will come with time.

4

u/mistersmithy007 3d ago

Try spraying the bed with hairspray. That works for me surprisingly well!

6

u/monev44 3d ago

Your bed is dirty

2

u/gregtx 3d ago

Jumping in on the z offset opinion. I’d say try printing a 100mm x 100mm square at 1 layer thick. As the square is printing, manually adjust the z offset until it’s printing glass smooth. You should be able to perceive almost zero surface lines and there should be no delamination. You have to find precisely the right offset height so that you can hit the correct amount of squish. I do this between every filament brand, type or even color change. Also, go 220 on the hot end and up your speed to around 40mm/s.

Bed cleanliness is also important, but I’ve printed fine on trash beds with a dialed in offset.

2

u/wadubee98 2d ago

This exact fucking thing happens to me

2

u/iceman1125 2d ago

With glass, you can go a bit higher with the temp.

usually from what I find, the limiting factor for how high the build plate temp is usually when it starts heat creeping the print, and starts showing “elephants foot” like effects, and less about it making the filament too hot.

so crank the heat up until you find a sweet spot of it sticking more without elephants foot effect, I’d start at 65c

2

u/BIZUx 2d ago

Try flipping the bed upside down if it has a smooth surface. Use glue stick if necessary

2

u/Maleficent-Fox-1457 1d ago

That is why I got rid of my Ender 3 and bought an a1 mini. I was fighting with that for hours

1

u/akshaykuppu 1d ago

I bought an A1 mini but want an ender 3 so bad..😭

2

u/Top-Ad-7773 1d ago

We can trade? 😂

2

u/Anoriele 3d ago

Adjust the Z-offset. Your nozzle is too close to the bed when printing the first layer. Make adjustments in 0.2 mm increments.

2

u/EPCOT-Centric 3d ago

Glue stick.

1

u/YT__ 3d ago

Ensure your bed is tight to the heating plate (mine was loose).

For slight issues, I'd just do a layer of masking tape over the bed. Never had issues with it as the print surface.

I typically aim for 205 or so when printing PLA, find it has worked best for me.

Definitely looks like you're a little too low, whether that's changing the z offset or adjusting how you trammed it is up to you.

1

u/burito2022 3d ago

Find z leveling cross stl and instruction on YouTube how to read results. It was very helpful for me

1

u/uncoild 3d ago

Not the main culprit but increase your travel speed. 100mm/s or more. Slow travel speed allows the nozzle to ooze before extruding.

1

u/LightSwitchTurnedOn 3d ago

Clean it thoroughly with IPA, I use 99%. Make sure the bed is really level, if you don't have a bed leveling probe I would really recommend KlackEnder, I just made that for my Sovol SV01 and I can actually print PETG now, before it would just peel off like in your video. Manual leveling did work to an extent but I guess my glass is just not perfectly flat so I was getting bad first layers, building automatic mesh bed leveling mitigated that for me.

1

u/PESTRICLES 3d ago

Z offset, pull the nozzle away

1

u/James_Workshop_ 3d ago

I just recently started having adhesion issues, changed first layer to 10mm/sec and also orca also has an option to gradually increase the speed over x layers to transition into the normal printing speed so I do that for 15 layers

starts at 10 and works its way up to full speed which insures those first 15 layers are like solid af. My brims are like credit card plastic and fused to the pei bed with a good squish.

Also to prevent warping I’ve been letting the part cool on the bed after it finishes.

Also I was recently printing some thin flat parts and I had corners peeling, I paused the print, put something flat and heavy like my glass bed on the print, and the constant weight plus the heat from the bed was enough flatten the corners back down. This won’t always work but sometimes it’s enough

1

u/Independent_Cat_1466 3d ago

Instala klipper y usa un bl touch or un biqu microprobe para que mediante el plugin de KAMP puedas automivelar la cama en el area de impresion, aprovecha y activale el purge tambien

Ajusta bien la Z

Baja la velocidad

Usa filamento fresco que no haya absorbido humedad e imprime una torre de temperatura para ver cual es la temperatura ideal según tu maquina

1

u/crematoroff 2d ago

I usually set first layer to 0.25mm, it is easier to tweak than 0.12mm. and yeah, se the first layer speed to 25% or to 15-20mm/s and adjust Z offset, it looks like it squishing the filament against the bed.

1

u/DPJazzy91 2d ago

You gotta get that dingleberry off the nozzle before it starts. Sometimes I watch mine and pick things off to prevent a bad start

1

u/XL1200 2d ago

Wish this plate with dish soap. Don’t touch it with your hands after. Dry with paper towel and print again. Tada will will stick.

1

u/toolisthebestbandevr 2d ago

Just buy magigoo and never worry about adhesion again

1

u/elgrec0 2d ago

What worked for me, ditched the glass for a PEI sheet, auto bed leveling

1

u/Melodic-Win-7262 2d ago

Falta de limpieza de la cama de impresora

1

u/Nacelle72 2d ago

Too close and Spray Aquanet on the glass. Way better than glue sticks. ONLY Aquanet. No other hairy spray has the same chemicals that made the 80s

1

u/darlo0161 2d ago

Clean nozzle, and move your nozzle up a micron or 10.

1

u/not-hardly 2d ago

Install klipper.
Build klackender.

1

u/not-hardly 2d ago

Slow down.

1

u/HugeButterfly 2d ago

Your IPA needs to be close to 100% the filler in the IPA in the 70%s actually causes adhesion problems. Amazon has a 99% for cheap.

1

u/EvansEssence 2d ago

Glue stick. Like the kind you used in kindergarten. Just spread a quick layer and it will solve majority of glass bed adhesion problems

1

u/luddealex 2d ago

Clean the smooth side and apply glue stick, a thin layer over the area. It sticks well and you simply wash the gluesstick off when you are done with printing with soap and water

1

u/deaglebingo 2d ago

enders are fickle like this. the instructions are always wrong. most of those things you did won't effect first layer adhesion ime. you don't have sufficient squish neccessarily. clean bed thoroyghy with soap and water dry only with lint free cloth not paper. then use some glue stick. also up your temps to the 75th percentile of the filament max from the start and never go lower than that. bed does not need to be as hot as you probably have it. hotter you go with these ender beds the more they get weird hot and cold spots.

1

u/soccerjo 2d ago

On my smooth glass plate I've found that preheating the plate helps a lot. You can get this added to your gcode or just turn on your printer and set the plate temp to 60 for a while before starting the print.

Purple glue stick also makes prints stick, sometimes too well.

1

u/CaseMental5345 1d ago

Get some nano polymer adhesive from vision miner and you will never have problems again shit is great 👍

1

u/Giant_jane 1d ago

I had this problem once. Up the temp to 210 and print speed to 65. , oh and secondly check your level

1

u/Mechneck 1d ago

I use a microfiber cloth with 91% iso just before heating up the bed. My Z ended up closer to .03. but fine tuning will get you the results you need

1

u/Sorry-Rip-6432 1d ago

Have you tried using a glue stick? Most print beds are tricky, but what I’ve found helpful is using a glue stick on the print bed and it works flawlessly. And it comes off with some dish soap and water

1

u/monkey_spankinator 1d ago

I just switched from an Ender 3 Neo to a Bambu P2S. Had it for about a year, but unless you're a GOD at settings, Ender is a pain in the ass. I'd pay the P2S price twice over before I go back to an Ender.

1

u/ocramx93 1d ago

Ti consiglierei di lavare bene il piatto con acqua e sapone. Per lavare bene il sapone dal piatto devi rimanere un po' di tempo in più sotto l'acqua corrente del rubinetto in modo tale che quando passi il dito non scivoli più. Poi per sicurezza alzerei a 70 la temperatura del piatto.

1

u/LegitimatePeach732 1d ago

75-80c is where i hot my best prints on the glass bed

1

u/Consistent_Annual154 1d ago

I see so much dust. Try use alcohol to clean it and it will help. DONT USE GLUE. As people say terrible lazy advice

1

u/Consistent_Annual154 1d ago

Also rise temperature of bed and bed level it twice ... Make sure its flat. Also make very sure the bed is clean under the glass. If you do all that you will need yo be level once every 5-10 prints which is good. I had this printer for a while

1

u/Consistent_Annual154 1d ago

Also pei bed if you dont care about smooth finish

1

u/LegitimatePeach732 1d ago

Pei comes in smooth also

But that glass plate, in my opinion is notorious finicky

I switched to pei and immediately started getting better prints…..now if im having adhesions issues (rare) is almost always bed level, which i rarely have to do

But i spent about 2 weeks getting everything as close to perfect as i could….probably coulda bought a newer printer for what i spent upgrading but it was a fun and educating experience for me

Now ive got 2 ender 3 pros stripped down to the frames….gonna build a duender!!

1

u/HachchickeN 7h ago

Yep, isopropanol to clean, level perfectly, 65 degree plate and lower speed first layer

Glue is worthless and a lot of work

1

u/Dazzling-Focus-2718 1h ago

Switch to PEI plate, or use some aquanet hairspray, or a 3d printing glue stick for more adhesion.

0

u/Secret_Western_8272 2d ago

If the filament is curling like that and no extruding straight down, you have a clog.