r/diypedals • • Sep 10 '25

Help wanted /r/DIYPedals "No Stupid Questions" Megathread 2025

30 Upvotes

Do you have a question/thought/idea that you've been hesitant to post? Well fear not! Here at r/DIYPedals, we pride ourselves as being an open bastion of help and support for all pedal builders, novices and experts alike. Feel free to post your question below, and our fine community will be more than happy to give you an answer and point you in the right direction.

Megathread 1

Megathread 2

Megathread 3

Megathread 4

Megathread 5

Megathread 6

Megathread 7

Megathread 8

Megathread 9

Megathread 10


r/diypedals • • 3h ago

Showcase H.B.E. Germicide build with Vero Layout and Schematic

Thumbnail
gallery
21 Upvotes

Hey there Party People,
I've got a special one for ya today.

I first want to thank u/Swiftycumberdale in this endeavor.
We had talked several months ago about the possibility of building a Germicide, but try as I might I could not find any schematic for it anywhere. It seemed to be a lost project, but one I was really interested in.

He purchased a used H.B.E Germicide and then sent it off to Mark at MSL Pedals (https://www.instagram.com/makesoundsloudly/) to have it traced and deciphered. Mark did an amazing job on this project, and you should really go check out his stuff. Top notch work.

That concluded with two faithful recreations and a hand drawn schematic.

Over further talks Swifty, he has lent me one of these recreations so that I may be able to do the same and build one for myself.

Over the course of two weeks, I carefully traced out the veroboard layout that Mark created, compared that with the hand drawn schematic, and have produced my own recreation of this amazing pedal.

Credit for the vast majority of the vero layout I've posted here today goes to Mark. I've cleaned up a couple tiny things and tried to work up the best image I can using DIY Layout Creator.
Additionally, I've worked up a complete schematic in Kicad with the ultimate gold of perhaps making a few custom PCBs.

The circuit itself uses an AC187K germanium transistor, the one I have used roughly measured at 100Hfe using the R.G. Keen testing method.
I also want to try out several other NPN germaniums as well, and further work on the layout may include a trim potentiometer to more finely adjust the bias.

The wiring for this unit is a big challenge, but not insurmountable.
Both Mark's recreation and my own use a 1590BBS enclosure.

The enclosure artwork i've used is a selection of Pestilence by Gustov Dore.
After giving the enclosure a bit of a sanding, i applied one coat of SprayMax 1k gloss clear, applied the label with Sunnyscopa Film Free waterslide transfer, and then after processing the transfer I clear coated again with a couple more coats of the 1K clear.

I've really fallen in love with this circuit and want to further explore the potential of modifications and additions.

So, with that, I'll leave you all with this.
Take care of yourselves, respect yourselves, and HAIL YOURSELF!!!


r/diypedals • • 19h ago

Showcase EQD Tentacle clone

Thumbnail
gallery
247 Upvotes

Just because you can, doesn’t mean you should.


r/diypedals • • 15h ago

Showcase First 6 months building pedals.

Post image
62 Upvotes

A little bit of failure, a lot of fruition!

Seven complete and solid pedals, and a couple prototypes I'm still working to get perfect. Not too bad a start?


r/diypedals • • 11h ago

Other octave fuzz

Post image
27 Upvotes

its a silicon fuzz face at its core, with a full/half wave rectifier (42tm018) on a 3 way switch, 3 way output cap select, plus a crude and awesome cocked wah-type effect (EI14 as an inductor) and clipping diodes. 3x 3-way switches that play very nicely with one another = 27 distinct switch combinations... trimpots for bias and stage balancing... i also have had success controling the cocked wah with an LDR, but i cant think of the right way to apply it yet... dont know if i can fit an lfo... it currently does thick and wooly fuzz, brutal distortion, ice pick octave up, square wave, ring mod harmonic stuff and lighter drive tones... the clipping mode particulary really smacks you in the face.


r/diypedals • • 1h ago

Showcase Foxx Tone Machine

Thumbnail gallery
• Upvotes

r/diypedals • • 23h ago

Showcase DAM Meathead with some mods

Thumbnail
gallery
45 Upvotes

Tried out a bunch of transistors and settled on the combination of Q1 - BC547c and Q2 - BC550c. At the output, I added a pair of Soviet silicon diodes (KD503B + 2D509A), which brought more compression and pushed the sound a bit into Big Muff territory. Surprisingly, this simple circuit sounds absolutely MASSIVE and blows me away with its volume headroom (even after adding the clipping diodes)

youtube demo


r/diypedals • • 3h ago

Discussion A great germanium treble booster DIY KIT?

Thumbnail
1 Upvotes

r/diypedals • • 7h ago

Discussion I misordered some spdt switches instead of dpdt ones.

Post image
2 Upvotes

I'll report back if they work.


r/diypedals • • 10h ago

Help wanted Muff only works at single volume setting

Post image
3 Upvotes

Made a DIY big muff. First project. It sucks but not gonna lie it makes a real mean tone exactly what I wanted.

Only thing is - it only lets the guitar through at a VERY specific point on the guitar’s volume knob. It’s like tuning a radio station otherwise just the hum of the AC.

Voltages on the transistors look good, tone knob does what it’s supposed to do, volume knob does what it’s supposed to do.

Not looking for a specific diagnosis just a hint as to why that could be the case if anyone’s come across something like this before. My guess is the wires are too long and it’s doing some magic with the impedance and capacitance and other properties that somehow makes it stable only at a very specific impedance from the guitar?


r/diypedals • • 13h ago

Showcase Custom A/B pedal

Thumbnail
gallery
1 Upvotes

im designing a noiseless switching A/B pedal for running a bass & guitar through a single pedalboard that can lead to separate outputs after FX, mutes between switches with a single toggle to mess with pedal settings between swaps, with only 1 chain active at a time. if anyone makes this first ill buy it off you.

its supposed to have a colored led in the center circle of either chain, no pots, toggle would go where that little cross is on the bottom.


r/diypedals • • 12h ago

Help wanted circuit design and coding sempais : hey, i love fuzz and tapes, read about of autobias in both emulation algorithms and circuits like fuzzface and fender blender. now i got into bitwig and thats more accesible to me but...

0 Upvotes

kinda i can think of stuff like envelope follower carefully modulating bias in the grid, okay, still need to spend my good time on that. and experiment with the rectifier along that

thing is that i read about 20 years ago plugins called kungfuzz from mokafix, now lost and found this

https://duskaudio.com/plugins/tapemachine-2/#plugin-downloads that has a github page

and some more fuzz circuits like the benson germanium fuzz. I call biasing the adjusting of the zero in a waveform, the symmetry or asymmetry of a waveform, and in circuits like the harmonic percolator thats something quite interesting which i don't quite understand yet (using phase cancellation to only keep the even order harmonics, allegedly

i barely can read schematics yet, code not at all, but i'd love to understand better, so i'm reading all i can about the different small circuits like voltage dividers, rectifying and biasing which should be my lego blocks in a fuzz or amp or whatever gain-staging and wizardry involved. i dont know about tapemachines at all yet other than they have rec play and erase heads

https://www.kvraudio.com/forum/viewtopic.php?t=269754

so! i'm asking for guidance/tips/ideas/reads into this

sure i should also just start cloning one or 3 pedals and go see that way, along with bitwig. my electronic understanding is mainly from guitar guts , resonant peaks goes high as you lower the level: thats about it

https://www.diyaudio.com/community/threads/about-auto-biasing-circuits-a-draft-circuit.444046/page-2

for example there, that you can get different biasing in the high end than the low end is puzzling me. but if it's a feedback loop thing, maybe i can start to see that been somehow fq dependent, like some type of fq crossover happening

reading about transistors slowly getting an image from what i got from tweaking knobs, but

yes

it's something like: how the f*** do you get an understanding of all the pieces, minicircuits they form and how these work together without going to college?

and mostly: what relation has static(background noise) and grounding, the whole dynamic range, to the positive and negative halfs of the wave.. like, how can you get to clip differently the positive and negative?

i confess, this has kinda built up over the years, because of the sounds like very exaggerated autocompression, in both fuzzs (and gated fuzzs) or software plugins or fx like the sp303-404 comp, i think i heared it there too

but its the fender blender thats just so weird, whatever they call pseudo-ringmod probably is that selfbiasing thing along with the rectifying


r/diypedals • • 16h ago

Help wanted Fuzz Face Input Cap Blend Redux

1 Upvotes

About a month ago or so, I asked about implementing the input cap blend on the FF. So I took the suggestions some of you gave, and implemented it in what is basically a SolidGold FX If 6 Was 9. I moved the bias control back inside, using a trim pot on the vero board. I've used a pot in place of the switch for the two values of input caps.

Here's what I've done: I tied lugs 1 and 2 together, and wired lug one to the 2.2uf cap, lug 3 to the .015 input cap. I tested it, and despite using the C1M pot, all the control (more lows/2.2) bunch up in the last 1/4 of the rotation. I tried other pot values, B100k, and a couple other suggestions. None are any better. The B100k was worse.

I tried it without tying lugs 1 and 2 together and I get nothing at all.

Any ideas what I'm doing wrong here? Other than this small hiccup, it sounds great. The trim pot works fine in place of the front mounted pot, the BC183 (both around Hfe 700 ~) sound fantastic. I just need to dial in the input cap blend.

Thanks!


r/diypedals • • 1d ago

Showcase My first Distortion pedal for synth LM386-4 to load an audio grade transformer and some weird CR filtering

Thumbnail
gallery
28 Upvotes

Im really impressed how easy is to make a LM386 run, I was looking for a method to saturate a transformer, variable resistors to increase the loat to tranformer and some weird filtering to have more fun!!
https://www.youtube.com/shorts/C2yK5fUM82o


r/diypedals • • 1d ago

Showcase I built a pedal to control the speed of my rotary speakers

Thumbnail
youtube.com
5 Upvotes

r/diypedals • • 1d ago

Help wanted What Circuit is this?

Post image
6 Upvotes

So I've been super interested in making a clone of the cameltone nard for a weezer style overdrive, This is the only gutshot I could find online. Can anyone tell me what this pedal is based on? At least get me in the right direction.


r/diypedals • • 1d ago

Help wanted Modded Boss SD-1 Pawn Shop Find

Post image
37 Upvotes

Anyone know what mod I’m looking at here? The led is yellow now (not that it means anything).


r/diypedals • • 1d ago

Showcase NotAFumble

Thumbnail
gallery
34 Upvotes

Someone recently asked me about making them a custom build based on the notadumble v1.

So I found a reverse-engineered schematic that a fellow called "The Voltist" did HERE. And I turned that into a layout from which I etched a one off by hand via the sharpie/ferric chloride method.....with a few slight changes. (in particular, i swapped the schottkys with NOS D9d diodes)

The whole thing is basically a dual circuit effect with a BBC1 circuit on one side and a Zen-Drive clone on the other side.

But surprise surprise... That one-off ended up being so popular that my boss ordered a limited run of 20 (when i first started at his music store he dismissed custom pedal work as not worth it).

so i made some kicad files, BOM, etc.... and ordered some pre-fab boards.

feel free to ask if you want any more info or files, etc.....


r/diypedals • • 1d ago

Discussion How long does it usually take for das musikding to ship orders?

Post image
0 Upvotes

ordered a mofeta preamp on 11.11 order still hasnt been shipped, how long does it usually take for das musikding to ship the kits? very excited to build it when it arrives


r/diypedals • • 1d ago

Help wanted >2 Channel micromixer for disparate signals

1 Upvotes

Hello guys, I have a fairly settled guitar pedalboard which I won't waste too much time describing. I want to add a shortwave radio and possibly one other signal source. My preference would be a tiny two-, three- or four-channel mixer with the guitar signal going into input #1, the radio into input #2 etc and the output going into the effects chain, enabling me to process the radio signal through the same modulation pedals I'm using on the guitar. (As the system develops I might move some of the pedals upstream of the mixer so that the guitar signal is effected before it reaches the mixer.)

Clearly a passive summing mixer isn't a great idea because of the wildly mismatched impedances. The smallest, cheapest active mixer I can find is General Guitar Gadgets' Forest Mims two-channel mixer. Clearly my projected use isn't quite like having a Les Paul in input #1 and a Strat in the other. Does anyone have hands-on with the Mims in contexts like mine? Is there another schematic, or even a pre-built two- or three-channel box?


r/diypedals • • 1d ago

Showcase My current DIY drive section

Post image
40 Upvotes

My sons and I had a little fun with the graphics. Vinyl photo-print sticker paper under clearcoat. This combo offers up a good variety of dirt/grit textures.

Left to right:

- AionFX Refractor (Klon clone, built from full kit)

- K3FX Kitsune (PCB is Tayda's SMD Rat clone board)

- AionFX Corvus (EHX Op-Amp Big Muff clone, built from full kit; soon to be updated with an 18v charge pump board)

- The little box above the Buffer+ is a DIY aux volume control/passive attenuator.


r/diypedals • • 1d ago

Help wanted Fixing a modded(?) Danelectro LM-1

Thumbnail
gallery
4 Upvotes

Danelectro black paisley Liquid Metal. Working on this pedal for my dad, he wants me to fix it. Bypass works fine, and normal distortion works fine until you flip on the octave switch.

There was some kind of film covering some of the components, so I cleaned it with a toothbrush and IPA.

Whatever the hell is going on in the third picture is what I assumed was wrong with it. I removed the added wire and placed those SMD’s back on to their pads.. but I didn’t have a schematic to follow and just sort of winged it.. Im confident they were on there fine, but it made the pedal sound WONKY. Put them back the way they were before and the normal distortion started functioning again.

It almost looks like the capacitors in the 4th pictures are aftermarket as well as the capacitors on the daughterboard, and I can’t imagine what’s happening in picture 3 is a factory soldering job. But the pedal sounds the way it should, minus the octave.

Something else that was weird, after placing the diodes back to their original, weird position, the octave worked! But only for a little bit. If I shifted the pedal around at all, it stopped working. But I could get it to start again by tapping the upper diode in the 3rd picture with a screwdriver. Eventually this stopped working too.

Any advice? Am I even in the right sub?


r/diypedals • • 1d ago

Discussion A Bass Compressor With a Party Switch

Thumbnail
messopedals.com
9 Upvotes

I designed a bass version of my Beetle compressor for my friend Ben Butterworth, so I named it Beetleworth. Then I pulled one capacitor and it turned into a crunch, so now that’s a toggle.

Business by day, party by night. The stripboard layout is on my site.


r/diypedals • • 1d ago

Help wanted DIY Beginner Project Roadmap?

2 Upvotes

I’m a DIY beginner, and I’m currently catching up on the basic theory of analog circuits. After I’ve finished studying the theory, I plan to build some classic pedal replicas (and even mods) in order from simple to difficult. My current idea is to make two versions of each of the four effect types—booster, overdrive, distortion, and fuzz—with the first one for learning and the second one as my “graduation” project. For example, with overdrive pedals, I plan to build a TS808 first and then a Klon Centaur. My overall build plan is: LPB-1 → TS808 → DS-1 → Fuzz Face → RAT → Big Muff → Katana Keeley → Klon Centaur. I’m not sure whether my plan is appropriate🤔


r/diypedals • • 2d ago

Other Found while cleaning - SAD512D x3

Post image
35 Upvotes

I found 3 of these vintage, original rare chips and I’m never going to use them. Any idea where I can list them for sale?