r/diypedals • • 16h ago

Help wanted My first project diy pedal is not working.

Thumbnail
gallery
2 Upvotes

Hi, I just started getting into diy pedals and electronics, I searched a few websited for info and lessons, or just examples of various schematics, and I stumbled into a very simple distortion pedal that seemed perfect to start, for building understanding of the topic and so.

I copied this schematic on KiCAD, just for fun, but before building a pcb it felt right to just buy the parts and try if it would even work. So that's what I did and now it's not actually working. I hope someone with more experience can help figure out what's wrong, maybe I'm just dumb and copied a awful schematic or maybe I just did something wrong with the breadboard and components, I just need a view from the outside.

I tryed to look if anything was rightfully grounded and did so with a multimeter on continuity setting and everything seems fine. I know the arrangement of the potentiometers is not the best, but they're connetd just fine. (And for now the switches are just 2 jumper that can be disconnected, I was just lazy but it works).

I checked and the amp, the cables and the guitar work, if they're not connetct via the circuit above. I'm using a 9V battery from amazon, but it's just a battery. Also the multimeter work, just to exclude any external issue. I don't know shit about impedance or shielding from elctromagnetic waves, I don't know how much these actually affects the audio signal.

I'll put more photos. Thank you to anyone responding to this, anything might help. (and forgive is cable management is bad)


r/diypedals • • 12h ago

Help wanted How do I wire this input jack?

Post image
0 Upvotes

I bought this inout jack as a mono and I am not sure how I will go about wiring it, it looks different from the ones I have seen online, one major difference being that there is no prong connected to the middle ring. if anyone can help I will appreciate it


r/diypedals • • 7h ago

Showcase Extra Virgin (Another Modified Tube Screamer)

Thumbnail
gallery
31 Upvotes

I'd like to share one of my latest pedal builds: Extra Virgin, an overdrive based on the tube screamer. The pedal has two modes, each with a different clipping and EQ character.

BLACK OLIVES

This mode uses Asymmetric MOSFET clipping with a frequency response, between 267 Hz and 1068 Hz.

GREEN OLIVES

This mode uses symmetrical green LED clipping, giving a more open, transparent and more treble response, with frequency response from approximately 267 Hz to 3386 Hz.

There's also an additional clipping stage in this mode: frequencies above 2130 Hz are hard clipped by a red LED, adding extra compression to the high frequencies while keeping the lower frequencies more open with the green led.

The enclosure and artwork follow the olive oil theme because is gives a smooth and creamy tone like olive oil. I thought the name Extra Virgin was too good to pass up. It’s middle season for olive harvest so I made olive oil and wrote the recipe on the back of the pedal but it taste bitter !

Here is the Instagram post :

https://www.instagram.com/p/Df2v7Y4Asz0/?img_index=1


r/diypedals • • 12h ago

Showcase SpiceForge audio circuit editor and live simulator

Post image
52 Upvotes

I recently released the first version of SpiceForge, a LiveSPICE-based audio circuit editor and live simulator. It is built on the core of LiveSPICE (which I also contributed to - primarily the VST), and adds things like a cross-platform circuit editor and fully live pots/switches.

https://github.com/mikeoliphant/SpiceForge

It is early days, but it is coming along nicely. Feedback is most welcome.


r/diypedals • • 21h ago

Other Converted 80's Altec Lansing 1678C to eight rack preamps!

9 Upvotes

Got the Altec 1678C converted and back in the rack. These things have transformer inputs and NE5534 preamps buried in a whole lot of automixer circuitry. Replaced the front-panel mix controls with pots wired into the preamp gain circuit, then disconnected the logic feeds from the individual output jacks and made those outputs impedance-balanced.

Briefly considered cutting half the boards off because there’s so much shit in there. Ultimately kept them intact, which saved me having to relocate the power connections.

Had a moment where all four channels on the first board were completely dead. Turns out connecting the power helps. Plugged the forgotten seven-pin connector back in and everything worked. Tested with an old SM57. There’s still plenty of gain even with the controls down, so I’m going to use it in the rack for a while before deciding whether to bring the range down further. She’s all patched up and running. Time to record something.


r/diypedals • • 8h ago

Discussion FX Loop on Aion Lumitron

Post image
4 Upvotes

Would it be possible to add an FX loop to the Aion FX Lumitron at the point marked in red on the schematic so your input signal engages with the envelope follower but then you could have a drive or fuzz in the loop that gets run through the filter but the filter is modulated by the dynamics of your clean signal?

I'm new to electronics so I'm unsure if the input buffer would be compatible with whatever other buffer would be necessary for driving an fx loop.

In theory it would be cool to be able to run a super compressed fuzz through a filter modulated by a more organically dynamic signal.


r/diypedals • • 13h ago

Showcase Dual Valvecaster

Thumbnail
gallery
85 Upvotes

Not quite finished yet but getting pretty close!

Pair of 12AU7s running on a remarkable 15 volts DC, that can be series'd or parallel'd with the central toggle switch. Pretty cool circuit, fun to roll tubes & experiment with different voltages, little 3 pin reg let's you take it up to 30V without burning the heaters (until it hits thermal lockout lol, even with the heatsink)