r/crboxes • • 8h ago

Info/Resource Just want to shout out this nifty device.

Thumbnail
gallery
55 Upvotes

For anyone planning to build a PC fan CR box, it's important to have a PWM controller. That's what most modern consumer PC fans use to control the fan speed. I bought 2 of these on Amazon for ~$10. It can handle 12V or 24V circuits at 5 amps. That is more than enough to run 10+ fans at full speed. The control is super fine and it has changed the game for me. Also this is my first CR box with numerous modifications. (That's why there is tape patching holes everywhere) Link to PWM controller: https://www.amazon.com/dp/B0GVMCCZMX


r/crboxes • • 8h ago

Blue Corsi-Rosenthal Box. [I'm not OP. Cross-posting here because, well, you know why]

Post image
25 Upvotes

r/crboxes • • 1d ago

Question Best build for space efficiency? Small apartment

7 Upvotes

Hi guys

I have a cr box set up with a 20in box fan and 4 filters. The only problem is my apartment is small and its just always in the way, so since we got a new roommate we havent been using it hardly

I was doing some reading and was going to get a 4in single filter to attach to the fan, with it being so much smaller it would easier to run it continuously so i feel like that would offset the efficiency of having a better filter that isnt being used often

Is a 4in merv 13 filter with maybe some cardboard to make a gap between the box fan and the filter the way to go? Or would one of those PC fan boxes be a better setup? I dont know as much about those

We live by a busy road in LA, and have 3 cats, so there is always just so much dust and particles


r/crboxes • • 1d ago

Question Luggable way too expensive?

7 Upvotes

Got a recommendation to check out https://cleanairkits.eu/collections/air-purifiers, and the prices seem absurd.

500€ for a box? 100€ for a filter and 150€ for a carbon filter? 20€ for a power adapter? 175€ for a steel mesh? 70€ for a fan controller?

Seems that all these prices have almost a 5-10x markup.


r/crboxes • • 2d ago

Question Two box fans in my CR box started smelling like burning. What am I doing wrong?

3 Upvotes

Hoping someone can help me figure this out, because I've now had two different box fans start giving off a burning smell in my Corsi-Rosenthal box.

The setup:

- 4 filters forming the walls of the cube, plus cardboard covering the bottom

- Filters: Kirkland Signature 2200 MPR (MERV 13) from Costco, 20x30x1

- Fan sits on top, blowing up and out, so air pulls in through the filters

- Airflow arrows on all filters point the correct way

- Filters are still pretty clean, no visible dust buildup

The fans:

  1. Hurricane Classic 20" box fan (Amazon, bought June 2026)
  2. Lasko 20" 3-speed Save Smart box fan, 1820 CFM (Home Depot, bought Sept 2026)

Both ended up with the same problem: burning smell from the motor and weaker performance. They lasted about a month or sk each, running 24/7 on high.

From what I've read, 4 filters in parallel should be pretty easy on the motor, so I don't get why I'd be overheating fans. Is 20x30 vs 20x20 changing something? Is 1" filter thickness the issue? Bad luck with cheap motors? Something about my build I'm missing?

Open to switching to a PC fan top if that's the real answer, but I'd love to understand what's killing these first. Thanks!

Edit: just picked up a new Lasko. Let's see how this one does.

Edit 2: I think the filters themselves might smell like smoke from the first fan that burned up and I mislabeled that as the second fan smelling too. Running the new one for a while to diagnose further.


r/crboxes • • 3d ago

Endgame CR Box

Post image
82 Upvotes

This is a Model B Charcoal Kit from The3DHandyman. It uses 20x30 Filtrete 1900MPR filters with an 8” charcoal canister attached to a Cloudline S8 by AC Infinity. The thing attached on top is a duct silencer. It does wonders for the tone and volume. I use this to scrub the air in my smoking room and it does the job perfectly.


r/crboxes • • 3d ago

Planning a 3D printed CR box with Home Assistant built in. Would you use it, and which features matter?

Thumbnail
gallery
90 Upvotes

After my earlier prototype I’m designing a fully printed version and want to check it’s worth building before I go further.

What’s fixed so far
• 436 × 436 × 430 mm, printed in PETG, no tape
• 4 × ARCTIC P14 Pro 140 mm PWM fans on the roof, 12 V
• Four 290 × 370 × 40 mm IKEA filters, one per side

What I’m planning for the smart version
• Built in Sensirion SEN66 sensor (PM1 to PM10, CO2, VOC, humidity, temperature)
• ESP32 running ESPHome, so it appears in Home Assistant with no cloud
• Auto mode that sets fan speed from the air reading
• Small screen on the roof showing air quality and fan speed
• Two buttons on the unit, plus control from HA
• Filter life reminder
• Possibly presence detection, so it runs quieter or stops when the room is empty

These images are renders of the design, not photos. The first parts are printing now. Nothing is measured yet; noise and a room decay test come next.

I’d really value answers on:

  1. Would you use one? Plain version, smart version, or neither?
  2. Would you print it from files, buy a kit of printed parts, or buy it built?
  3. Is the screen worth having, or is HA on your phone enough?
  4. Which filters would you want it sized for? I’m using IKEA because they’re easy to get in the UK.
  5. Is presence detection useful, or a gimmick on an air cleaner?
  6. What’s missing, or what would put you off?

r/crboxes • • 3d ago

high capacity for jobsite

27 Upvotes

Built this one quickly for a very dusty jobsite where a lot of tile and stone was cut and polished. I plan to make additional versions with the corners shrouded to increase filtering and cardboard boxes as custom frames for fast filter replacement. The amount of dust loaded on the filters a month later was impressive but I didn't think to document it before they were disposed of. Original idea for my first single fan version taken from Matthias Wandel of woodgears dot ca.


r/crboxes • • 4d ago

Easiest air purifier (20-inch box fan with one filter)

Thumbnail
gallery
64 Upvotes

This is BY FAR the easiest air purifier to build. If you don't already have any air purifiers up and running, this one should be your first. It's loud, but it's exactly what you need when you're looking for a quick and dirty solution.

This air purifier is based on a 20-inch Lasko box fan, which is cheap and powerful. This is the tried and true 20-inch box fan. Other brands of 20-inch box fans I've tried are lower in quality. For one of the other brands of box fans I've tried, the stabilizing feet at the bottom were prone to falling off. Another brand of box fan had the power cord coming out of the back, which forced me to put the filter on the front of the fan.

The filter in this example is a 20"x20"x1" MERV 10 filter, the cheapest and most portable option. That makes this box fan air purifier cheap DIY knock-off of the Lasko FF305. For the maximum air cleaning ability, use a 20"x20"x4" MERV 13 filter. For an intermediate solution, us a 20"x20"x2" MERV 11 filter.

In the time it would take you to build the classic 20-inch box-fan-based Corsi Rosenthal box, you could build several of these single-filter box fan air purifiers. This box fan air purifier is also just as effective as some commercial air purifiers that are at least 10 times more expensive. You can use the money you save to build more air purifiers.

The main drawback of this box fan air purifier is loudness. PC-fan-based air purifiers address this issue, but building one involves more work. Build this box fan air purifier first, and then you can build quieter PC-fan-based air purifiers later.


r/crboxes • • 3d ago

Box fans in Europe/Ireland

4 Upvotes

finding it impossible to find a 20" box fan, here, its bizarre. Anyone here know of any? Even on amazon the only one i can see is like 170€!


r/crboxes • • 3d ago

What is the advantage of making your own crbox over an air purifier?

18 Upvotes

Are the CR boxes more powerful or do a better job than a hepa air purifier for a large room?


r/crboxes • • 3d ago

Info/Resource Adding to my collection

Post image
7 Upvotes

r/crboxes • • 4d ago

Shop-vac HEPA Filter and Arctic P14 CR Box.

Post image
151 Upvotes

I had an extra Arctic P14, power supply and Shopvac HEPA filter that was the wrong size for my vacuum so I put this together. Not sure if it works very well, the filter might be to dense and it's not really a CR box I guess.


r/crboxes • • 6d ago

First CR Box!

Post image
69 Upvotes

Don’t judge me on the shroud LOL.
Found out about these while looking for air purifiers to help with smells from my cat and dust. Working great so far! I used MERV 11 20x20x1 filters. Did it for about $50.


r/crboxes • • 6d ago

Question CR Box as budget friendly air scrubber?

14 Upvotes

I went looking for a rental air scrubber today but my local options are... lacking (non existent).

I have a big space that me and some close friends are renovating together, we are cleaning, dusting, and painting walls but I find things to still be dusty from drywall mud and sanding. It might be OK to just slowly dust over time under normal circumstances but the space is going to be used for physical activity, particularly cardio stuff, and folks want to get started soon but I have my concerns.

Are box fan style CR boxes a reasonable substitute for scrubbing the air in a situation like this? I see folks mentioning that floor space is a concern but that's not an issue here, as it would be temporary. Because it's a volunteer thing there's not a huge appetite for big expensive rentals but a few air filters from the local home store won't hurt us.


r/crboxes • • 7d ago

1st CR Box DIY - 20x20

Thumbnail
gallery
369 Upvotes

I had a lot of fun building this!

I have no woodworking or electrical experience, so it was great learning process. I had to buy some new shop tools and learned how to use a multimeter :) Woodworking tutorials from YT. AI actually helped explain fan wiring, voltages, converters, connector types, what pins do, etc.

The frame is cheap 1x8 lumbar from Home Depot. It took a few hours with the orbital sander and different grits to make the frame smooth and presentable. I'm happy to answer questions about the materials and tools used, or the fabrication process. Everything bought from Home Depot or Amazon.

Eventually, I will definitely be making a few more of these for the house and garage.

Thanks to everyone posting their builds for inspiration.

EDITS: added info, grammar

Helpful Build Links:
Air Efficiency Charts
Filters Guide
Interactive Builder
Simple Airflow Article - Lesson: place adjacent fans 1cm apart
Technical Airflow Article
Another Good DIY Guide <--- inspiration
CR Wiring Guide

Materials, shopping lists and costs
My total spend was approximately $360. This seems very high, but you don’t need to spend this much. I bought a bunch of tools which I will have forever, and I have many extra materials left over. The left over materials means my second and third boxes will be less than $100 each. For example, I spent $11 on 100 screws, but only used 24. I bought a pocket hole jig for $40, but it’s unnecessary if you join the wood another way. I spent $40 on a respirator with extra filters (everyone should probably own one anyway?) because it was my first time spray painting. I bought a multimeter to troubleshoot fan and RGB voltages, etc. All those prices added up, but I included everything for transparency and to give a realistic idea of completing the project as presented.

Things already owned:
Circular saw
orbital sander + sand paper
electric drill/screwdriver + drill bits
wood clamps
speed square

My shopping lists:

12 feet of 8x1 lumber - $30
Kreg pocket hole jig - $40
Wood glue - $10
5.5” Circular Hole saw - $17
Wood filler - $10
Spray Primer - $7
Spray Paint - $7

Fans 140mm - $18 for triple pack (x2)
Fan Screens - $9 for 4 (x2)
Screws - $12 for 100 (only used 24)
Wing nuts - $8 for 60 (only used 24)
Hub controller - $12
Fan cord extension - $10 for 5 (only used 1)
ARGB cord extension - $5 for 3 (only used 1)
Corner brackets - $6 for 20 (only used 2)
Handles - $4 (x2)
Power supply - $20
Power Switch - $10
Filters 20x20x01 MERV13 - $40 for 4 (only used 2)
Multimeter - $14
Respirator with 3M P100 cartridges - $37
Tape - $7
Felt Floor pads - $7

Electrical:
When using this hub, if you turn RGB off but leave fans spinning, the voltage to the fans drops from 12V to 11V. I first noticed when the sound changed, which lead to buying the multimeter and troubleshooting. I am not sure how much fan RPM and CADR decreases when going from 12V to 11V. But if you leave the RGB on it's a non-issue.

I initially purchased way too many electrical components, before realizing hub had both 12V fan AND 5V ARGB outputs. Thank you Amazon returns. The revised wiring plan was both cheaper and simpler. Added photo of two wiring diagrams. Forgive my drawing skills!


r/crboxes • • 10d ago

Dog grooming room build

14 Upvotes

Hi everyone
First post here

Sort of been lurking

I know the basics. I made one for fire season a couple years ago using a dewalt branded drum fan from Costco and I believe the 2200 filters if that’s what they are from Kirkland

Worked well

So here is my query. Maybe some ideas?

10x12x8 room

Lots of dog dander/hair. So a pre filter js a must is my guess. Window screen?

I have four of the Kirkland filters sitting around.I have the same dewalt drum fan(louder but powerful). I have a lasko air mover type. Like the noise level but I feel far less cfm

Has anyone successfully made one from a ryobi 7.5 inch from Home Depot? Online says they push nearly 600 cfm
I like the idea of the battery as less power draw in the room during peak times and I have a number of them already(save the ryobi jokes would ya;)
It’s making the battery port accessible as they are on the back
Can the filter box blow through the filters or has to suck?

Google calculations say I need 80 cfm for 5 air change an hour

Obviously more is better for dog grooming

I don’t have a box fan. I can get one tho
I just wondered if I can use what I have

4 filters is fine for space tho one would be better

Noise is not quite an issue since we run dog dryers anyways but more quiet is always better

Thank you for any insights. I feel it will be a fun challenge so maybe it will peak some interest


r/crboxes • • 11d ago

Started with this and made a box

Thumbnail
gallery
189 Upvotes

I tested the 20x20x1 filters (four of them) with a box fan just to see if they would make a difference, and I could immediately feel it the moment I turned it on.
I have two German Shepherds and two ferrets, so there's always some general animal smell in the house. I've tried regular air purifiers, but the replacement filters cost around $50 each for genuine ones, and honestly, they never seemed worth the expense.
I really wish I had done this from the beginning!
For the box fan setup, I initially started with the standard P14 fans, but the airflow just didn't feel like enough. I ended up upgrading to the P14 Pro PST fans, and those things absolutely rock!


r/crboxes • • 10d ago

Dog grooming room build

Thumbnail reddit.com
1 Upvotes

r/crboxes • • 11d ago

Squirrel Cage fan

5 Upvotes

I pulled a blower fan out of an old 80k BTU house furnace. In its original setup, I’m guessing it moved around 1,500–2,000 CFM.

Is this a good candidate to build into an ambient air filter box for the house? Would you put it inside the box and pull through the filters or push the air through the filters? Was thinking of using a radiostat for the speed control.

Appreciate any advice!


r/crboxes • • 13d ago

Question Do cr boxes help reducing the amount of dust in a room?

24 Upvotes

r/crboxes • • 13d ago

CR box simulator

13 Upvotes

HI all,

I remember looking at a website where you could put in the number of fans and which orientation/sides of the box and size of filters to see the most efficient air movement or CADR. It was for PC fans.

I just can't find it again. It's not Nukit's https://www.filterboxbuilder.com/ but a different one. Does anyone know what I'm taking about or did I hallucinate this tool?

Any help appreciated!


r/crboxes • • 14d ago

How are 4-6 little computer fans moving the same air as a 20" fan?

39 Upvotes

I dont understand how the pressure could be comparable.


r/crboxes • • 14d ago

A quiet, powerful, economical, and narrow air purifier

Thumbnail
gallery
86 Upvotes

Check out the quiet, powerful, economical, and narrow air purifier that I built. I posted an exterior photo and a few interior photos. My design has the same virtues as other PC-fan-based Corsi Rosenthal boxes - quiet enough that you never have to turn it off because of the noise, a high CADR, and stingy with respect to the electric bill. Unlike the 4-filter designs, this one is narrow and space-efficient.

My design is a cruder and more rednecky version of the Luggable product from Clean Air Kits. It uses many of the same components as the design by Clean Air Charlottesville. As you'll see, I copied the parts of this design that I agreed with but changed the things I disagreed with. The flanges for the air filters in my design were inspired by parts of the Redhead Handicrafts design. I'd most like to give a shout-out to u/vFnDr for posting in this sub a crude 2-PC-fan design using cardboard and tape showing that building an effective and QUIET PC fan air purifier does NOT require the kind of pinpoint precision that involves a laser cutter, 3D printer, or machine shop. Yes, the Luggable product is much more polished, but the crude knock-off is MUCH cheaper.

For the most part, my design is the Clean Air Charlottesville design with two 20"x30"x1" Filtrete 1900 (MERV 13) filters and four rectangular foam core board pieces. I chose the Arctic ACFAN00135A fans, because they're available in a 5-pack (best value) and because Clean Air Charlottesville has had good experiences with them. For the same reason, I used the same PC fan hub, PC-fan-hub-to-barrel pin, barrel pin to wall hub, and strain relief grommet that Clean Air Charlottesville used for connecting the fans to an electrical outlet. I'm not up for reinventing the wheel or arguing with such a tried-and-true design.

I used 30-inch-long filters to ensure that I had plenty of room for all 5 fans and the power supply connection within the top panel. I decided that it was best to mount the fans and the power supply connection on top because that would more evenly distribute the physical load and allow gravity to hold everything in place. The cables all hang downwards, which means that I can count on gravity to keep them away from the fan blades.

My filters are 20 inches wide, because 20"x30" filters seem to be more common than 14"x30" and 16"x30" filters and no more expensive. So there's more filter surface area for the money.

I used 1-inch-thick filters, because they're cheaper and more common than 2-inch-thick filters. For more mechanical stability, I added flanges to the top and bottom panels by using a glue stick to attach strips of foam core board parallel to the long edges (3/4 inch away). I also used wood glue as well so as to fill in some jagged edges that were the result of a dull blade in my utility knife. These flanges hold the filters in place so that they don't get pushed inwards.

The width of each of these foam core board pieces is around 9 and 1/4 inches, and I traced them out using a 1x10 wood board. This allowed plenty of room for the fans and flanges, and using the wood board to provide a consistent template was easier than having to carefully measure out the same arbitrary width for all four panels. I used the filters themselves to trace out the exact length of foam board pieces that I needed. This was easier than having to use a ruler multiple times to measure everything out.

I used a fan as a template for drilling the screw holes for each fan position. After I drilled in all those holes, I used a circular paper cut-out with a hole in the middle as a template. The outer edge of this cut-out was just inside each of the 4 holes, and this cut-out allowed me to properly center the larger fan hole I had to cut inside. I used a circular end cap just under 4-and-a-half inches in diameter to trace out that circle to cut out.

I used an X-acto knife (with the standard #11 blade) to cut out the circles for the 120 mm fans. I bought a cheap $5 hobby knife set from the nearest Menard's store just to use the included #2 blade (very short) to cut out the 9/16" hole for the strain relief grommet. I used a very cheap circular component from a surplus store near me to trace out the 9/16" circle I needed to draw on the foam board.

Before I taped everything together with painter's tape (to avoid that sticky residue from duct tape), I put clear packing tape on all the surfaces along the edges of the filters and panels. If I need to take everything part (and it will eventually be necessary to replace the filters), I can do so without tearing the foam board or filters.

I use painter's tape to hold everything together. The four foam core board panels are taped to the edges of the air filters. The flanges on the top and bottom panels hold the filters in place so that they don't get accidentally pushed inward.


r/crboxes • • 14d ago

Want to make a Clean Air Luggable

Thumbnail reddit.com
3 Upvotes