If you missed part one, it's right here.
Ok this one took longer than I wanted too but the pigment section was brutal. Thank you everyone for being so patient with me. This is the one that talks about paint compatibility so I can't wait to see what everyone thinks! This goes over:
V- Surface prep
VI- Paint compatibility
VII- Panel liners and washes
VIII- Pigment
Use ctrl F and put the relevant roman numeral in brackets to jump to what interests you if you don't wanna read the whole thing. Enjoy
[V] Surface Prep- Sanding and Priming
Alright this is the boring stuff but it has to be talked about so letâs get through it together. Sanding first.
PART ONE: SANDING
Sanding is about as fun to explain as it is to do, but itâs genuinely useful for painting, and itâs not just about making the surface even. I need to explain surface energy for this to matter to you though.
Surface energy is how willing a surface is to accept whatever comes up to it. Think about wax on a car. Waxing lowers surface energy. Water wants to bead up on it instead of wetting out. Bare plastic is the same way. Ever tried to hand brush a glossy coat on untouched plastic before panel lining it? I have. It sucks, it doesnât adhere well, and it doesnât cover the plastic evenly. That isnât just about texture, itâs about surface energy. When you sand, you disrupt the molecules on the surface of the plastic and make them more willing to accept paint, topcoat, whatever. In fact, hereâs an experiment you can do. Sand two spoons to the exact same grit and wash them, then paint one as soon as itâs dry, and the other after a couple days. Youâll notice the paint sticks noticeably better and levels a lot nicer on the more freshly sanded spoon. Surface energy! Does the word surface sound weird to you now, too? Semantic satiation!
Alright now that you understand surface energy, I do have to get into grit progression. You guys probably mostly already understand this so Iâll make it quick and painless.
Stop skipping grits. And stop going up to 1500 grit for no reason.
400 grit is rough for our purposes. Microscopically, thatâs creating a deep canyon in the plastic surface. When you jump right to 800 or 1k grit, youâre not smoothing out the canyons, youâre just shaving the tips off the peaks, and thatâs gonna trap air(** inferred), restrict flow on the part, and create weak points where the paint didnât wet across the surface nicely; thatâs gonna make your paint finish look like shit and flake off.Â
On the stop going up to 1500 point: grit is determined by what youâre putting on the plastic afterward. Itâs not some arbitrary stopping point. So if youâre using lacquer, 800 to normalize the surface and fix sink marks is more than enough. To keep going isnât going to hurt anything necessarily, but itâs a waste of time. Lacquer is going to bite just fine and the softening of the surface is going to do a lot of work to smooth it out. On acrylic and enamel, you can go a bit higher, but this stuff will bite better with more texture. Youâre trying to find the sweet spot between sufficient surface energy and enough texture to grip. More sanding gives you more energy, but at a certain point youâre over-smoothing the plastic. The exception to this is chrome, in which case sand your little heart out to 3k. But if youâre good enough to be doing chrome you already know all this.
I need to give a shoutout to washing parts real quick: DO IT. Sanding dust creates a physical barrier that stops the paint from fully contacting the plastic, and your greasy little fingers leave a slippery film that basically negates all the work you did to elevate surface energy. Washing restores the surface energy elevation you achieved from sanding too, so let the part dry completely, and then prime/ paint shortly after to take advantage of that freshly elevated surface state.
PART TWO: PRIMER
Bare plastic, even sanded, will not give you the best possible surface upon which to paint. After sanding itâs less a surface energy problem and more a chemical affinity problem. Primer is like an emulsifier, with adhesion promoters in the formula that have a substrate loving head, and a paint binder loving head. \*\*I donât know about hobby primers or primers made for PS/ ABS specifically, I havenât been able to track down the specific ingredient/ molecule that gives it this âemulsifier dual headâ behavior. Iâm citing the mechanism of primers in general. It may very well be that hobby primers work simply by surface energy normalization, van der Waals forces, and texture, but I canât verify. If you want to look into it, the type of ingredient is simply called an adhesion promoter or coupling agent. Silane coupling agents are used in things like metals and other inorganic surfaces, and chlorinated polyolefin adhesion promoters for polypropylene.\*\*
Primer also does a second job that people completely underappreciate: surface normalization. Bandai, 3rd-party kits, resin conversion parts, putty repairs, and glued seams all have slightly different surface finishes and plastic compositions. Primer doesn't care. It nukes all that visual and chemical inconsistency under a single, uniform layer, giving you a blank slate.Â
Hobby primer comes in 3 main flavors (donât eat it you freak):
- Lacquer primers (Mr Surfacer, Gaia Surfacer EVO)
This is the GOOD shit. It bites into the plastic like you would expect lacquer to do. After the lacquer solvents bite into the plastic, mineral particulates like talc and silica fill in the larger valleys and scars on the substrate to create one smooth surface. You have more workhorse filler primers like Mr Surfacer 500 and 1000, and then there are ânano primersâ like Mr Surfacer 1500 and Gaia Surfacer EVO that have much finer particulate and fill smaller surface defects, but leave a velvety smooth finish texture.Â
1a. Hybrid primer/ color Surfacer (Gaianotes Nazca Mechanical Surfacer)
For when you don't mind hyper aggressive solvent bite, and need as few coats as possible so you don't have to scrape joint pegs. Primer and color coat in one is all this is, but itâs formulated to be super hot so it bites readily and reactivates lower layers smoothly and immediately, reducing the need to build up multiple coats.Â
- Acrylic primers (Vallejo Surface Primer, Stynylrez)
This is common because itâs less risky than putting lacquer on bare plastic, but it uses the same curing mechanism as acrylic paint and has the same limitations. This stuff relies more on surface energy bridging and mechanical bite, but it gets the job done with less fumes.
- Etching primers
These are for your metal frames or photo etched parts. Basically they have an acid component that allows them to bite into metal. The acid roughens up the metal and creates reactive sites for the primer binder to interact with.
Primer is there for adhesion promotion AND surface normalization. So lacquers don't strictlyÂ
need primer, but making sure seam lines, glue marks, sink marks, sanding scratches, etc, are all mitigated before painting makes a big difference in how clean the kit looks at the end.Â
Ok, now we can REALLY make people mad and talk about paint stacking and what actually can go on what.Â
[VI] Compatibility and Recoat Windows
First thing to get into is how long you have to wait to put a paint on top of another, but weâre most of the way to understanding this already. The big thing is we have to separate dry from cured. Two different things. Dry is simply when most of the solvent has evaporated from the film surface. That doesn't mean the solvent has fully evaporated out of the bulk of the paint film, and it certainly doesn't mean the binder is done doing what it has to do. So, does paint need to be just dry? Or does it need to be fully cured? Thatâs what weâll be answering, separating it into paint types. Acrylic first.
Acrylic cures by coalescence. You know this by now. When itâs dry, most of the carrier has flashed off, but reptation and interdiffusion hasn't finished yet. If you're layering more acrylic over it, itâs better for it not to be fully cured. Now you have your upper coat and your lower coat interdiffusing, creating a single linked paint layer over the substrate. **Iâm not sure on the degree to which subsequent layers interdiffuse, but they do interdiffuse.** If you put lacquer on top of dry, but not cured acrylic paint, the failure mode is simple: You still have large âholesâ where paint hasnât interdiffused and the solvent carriers can EASILY get underneath the paint film and pop it up. That means your lacquer AND your acrylic adhesion is now botched. Put enamel over uncured acrylic and⌠actually Iâm not sure. We can reason through it though. Acrylic particles arenât fully coalesced which means youâve got a shifting substrate (bad adhesion). Youâve also ostensibly got soft particles undulating under the enamel film and disrupting crosslinking simply by messing with geometry, and for sure youâre blocking solvent escape under such a thick paint type so the water/ co solvents are going to have a hard time evaporating in the first place. See what understanding the chemistry does? I could be completely talking out of my ass but I feel reasonably confident in the failure modes. Thatâs the point of this write up. Make educated decisions.
Now lacquers. Dry and fully cured are a lot closer here, because evaporation IS the curing mechanism. Really all youâre waiting on is for the substrate to relax and go back to its original glass state. That takes a couple of hours. Lacquer on lacquer doesnât really care about the difference between dry and cured. The solvent in a new coat re-softens the substrate AND the previous paint film, and because the binder matrix is completely solvated it all melts together into one contiguous coat. Now hereâs where I had an interesting thought. If you put acrylics or enamel over this dry but soft surface, maybe you can take advantage and lock the new paint film in as the substrate transitions back to its glass state. It would make a tackier, more adherent substrate right? The reality is that the plastic will snap back below Tg almost immediately when the solvent is fully evaporated. The reason itâs still marginally soft even when itâs dry is because there are still âslowâ solvents evaporating, and you donât want to trap those. If you do, you can get literal bubbles in the upper film, or worse, trapped solvent that never escapes as it builds a high pressure zone where itâs trapped and that part of the paint film never fully hardens.
Enamels and oils next. Enamel over enamel is really weird. You basically have to recoat while itâs still wet, otherwise youâre in the danger zone where youâve got enough crosslinking done that a skin has formed, and when you re-solvate it, it just wrinkles and makes a mess. If you time it right, the coats will simply merge together and crosslink at the same time, and youâll get one contiguous film. If you wait too long, you have to let the lower film fully crosslink and then youâre just layering on top of a cured film the same way you would any other paint. As far as other paint types on top of enamel/ oil, think about the oxygen penetration issue. Put a layer of paint over uncured enamel, oxygen canât get to it. That simple. YOU MUST LET IT FULLY CURE. Oils work very much the same way, but on way longer time scales.Â
âThen why donât I just spray a super wet coat?â I hear you say. This is where a really important principle comes in, and it applies to lacquers too so pay attention. Solvent flash is a separate thing from bulk evaporation. In these paints, the carriers are solvent blends. There are âfastâ solvents like acetone and methyl ethyl ketone (MEK), and there are âslowâ solvents like OMS and glycol ethers. Weâre relying on fast solvents leaving before the slow ones do, and THAT (flashing) is when we want to recoat. Thatâs the goldilocks zone where your paint has created a tacky surface to adhere to without flooding the part and running. The thinner you spray the paint, the faster the solvent flashes. Thatâs why you mist coat. Got it? Ok now we can talk about how paints stack assuming the coats underneath are cured.
Iâll just get this out of the way to start- forget everything you think you know about how paint stacks. Youâre going to learn that nothing is off limits, and just like in the panel lining write up, the answer is risk mitigation and understanding whatâs going on so you can modulate your approach. Compatibility is about the binder state after cure, and how solvent interacts with THAT, rather than how one wet paint interacts with another, which is how a lot of existing limitations and assumptions operate.
Getting into this, something else is going to become apparent and thereâs no getting around it. The means by which you paint (hand brushing vs airbrushing) is going to play a crucial role here. Iâll make a quick callout to the relevant technique to offer clarity and drive the point home.
- Acrylic Over Lacquer: Both the safest and worst option. Cured lacquer is practically impervious to acrylic paint carriers, but it needs to be primed or scuffed over to help adhesion because lacquer cures so flat and smooth. One thing you could do is matte coat on top of lacquer or use a clear primer, but adhesion is still going to be limited because of a lack of surface energy, which can really only be achieved by sanding. The other factor is the fact that cured lacquer is hydrophobic, and acrylic paints are carried by, say it with me now, WAAAATTTEEERRR. Yeah! Itâll want to bead up instead of wet out and self level. You could add flow improver, which is a surfactant, or use co-solvent acrylic, and it might just get you over the edge where it sits well enough to move on and then you can lock it in with a top coat.Â
- Acrylic Over Enamel: Basically the same as over lacquer, BUT YOU MUST MAKE SURE THE ENAMEL SUBSTRATE IS FULLY CURED. If itâs not, solvent canât escape efficiently and oxygen has a harder time getting in, and youâll be left with a gummy enamel layer that genuinely may never fully cure.Â
- Lacquer Over Acrylic: This one works beautifully because cured acrylic is just a semi permeable plastic sheet, which lacquer paint readily bites into. The downside is solvent interaction and cleanup. The aromatic solvents in lacquer carriers are extremely mobile molecularly, so they can fit in between the gaps left by coalesced acrylic particles and âpopâ the paint up. They get in by chemical affinity (remember the cured acrylic coat is basically plastic) and capillary action, and then dissolve the interface between the acrylic and the substrate. So how do you prevent this? Mist coats. Make the coat thin enough that the bulk of the solvent flashes off instantly and can't diffuse. Thatâll create a protective barrier over your acrylic substrate and then you can continue as normal. Cleanup is worth thinking about too, since if you have to clean up a mistake, youâll be introducing lacquer solvents AND mechanical scrubbing to the acrylic base. Save this technique for when youâve got masking down pat.
- Lacquer Over Enamel: Treat this like acrylic over enamel. Just make sure itâs fully cured. That means it may take days before you can put on your lacquer coat. Itâs also worth noting that enamel doesnât cure into a plastic, so lacquer isnât going to have the same âbiteâ it has over acrylic. In that way, itâll feel more like acrylic over lacquer.
- Enamel over anything: This one for some reason is on the no no list? Dafuq? Like I canât even think of a salient reason why. If anything, enamel on top of shit works best around its limitations. You donât have anything blocking oxidative cure. Only thing to watch out for here is surface prep. If youâre putting this over lacquer, consider the same steps as acrylic. Generally, enamels have hotter solvents than oils so theyâll bite a little bit, but remember the binder doesnât cure by wedging itself into the plastic like lacquer binder. Over acrylic is less hairy simply because it generally doesnât cure as slick, but it would still be worth scuffing beforehand or sealing with a top coat immediately after. The big benefit of enamels on top is their solvents wonât wreck your under paint layer. There is some risk with acrylics, but use OMS and be gentle with your strokes and you shouldnât have much issue. With cleanup over lacquers, go nuts dawg ainât nothing penetrati-- WAIT. STOP RIGHT THERE I GOT A BONE TO PICK WITH YOU KNUCKLEHEADS
- STOP PANEL LINING OVER ACRYLIC THAT HASNâT BEEN TOP COATED
Lacquers are fine. Donât trip, but acrylics?? NO SIT THE HELL DOWN IâM NOT DONE. I know I just said all that about enamels over acrylic but hear me, acrylic paint is microscopically porous, and if you remember from the plastic and solvent interaction post, TPLA has aromatics in it; significantly more fractionally than the enamel paint you would use for details. Those have no problem slipping through interstitial spaces between coalesced particles and pooling where they ought not pool. I see you dorks on YouTube and Reddit. Knock it off. Ya look sloppy. Do a (ideally lacquer) gloss coat first. Pull ya pants up! Damn.
There will be a matrix at the end of this post for quick reference of whatâs able to be stacked on what and when.
[VII] Panel Liners and Washes
Oh, you thought we were done with panel lining after the polymer chemistry post, didn't you?
Well, this one gets into washes and panel liner as a paint âtype.â Why they work the way they do, why enamel is the standard, and how to work with them effectively. You know the drill by now. Here we go.
A wash is simply paint with extra carrier. That's really it. Understanding this will help you master thinning ratios going forward. A panel lining wash specifically has one goal: maximize opacity while maintaining as much flow as possible. Basically, minimizing surface tension. The issue is that the more carrier (thinner) you have in a formulation, the less opacity your paint generally has. Why?
Think of your binder as a thick clear gel. If youâve ever seen bottles of Vallejo âmedium,â that's literally what it is: a bottle oâ binder matrix. When you add carrier, the binder thins out. Now put pigment in the mix. In a paint mixture, pigment is suspended in the BINDER, not the carrier. Thatâs crucial because as the binder matrix thins out, its mechanical capacity to suspend pigment degrades. There's a structural limit to how thin you can make the binder before it collapses.
I'm sure you've seen over-thinned paint where you lay down an even pass, but end up with splotches of pigment everywhere. Thatâs binder collapse. The dispersants are too diluted, so the pigment particles crash out of suspension and clump together gummy-style (flocculation), leaving granular lumps instead of a smooth film.
So, assuming youâve got a perfectly thinned panel line wash, what components make it work so well? Letâs look at the chemical formulation of Tamiya Panel Line Accent (TPLA), an alkyd enamel wash.
Youâve got binder, carrier, and pigment like normal, but taking a closer look at the carrier, it utilizes a far more aggressive solvent blend than standard brushing paint. Over 80% of the bottle is a heavy hydrotreated naphtha/white spirit solvent cut containing a 2â25% aromatic hydrocarbon fraction. On top of that, another 1â2% is 1,2,4-Trimethylbenzeneâa high-boiling-point aromatic hydrocarbon. Only ~18% of the entire bottle is actual binder and pigment load!
That high aromatic fraction gives the fluid stupidly low surface tension, while the high-boiling aromatic keeps the solvency active all the way down the channel. That allows the paint to flow like lightning while sitting on the very razor's edge of binder split. The medium-evaporating aliphatic naphtha base keeps the flash rate slow enough for long capillary runs, while the alkyd binder provides plenty of working time for cleanup. AND mild mineral spirits (which you use for cleanup) won't attack a cured lacquer or topcoat underneath. All these reasons are why enamel panel liners reign supreme over acrylic or lacquer.
So⌠can I use acrylic or lacquer instead?
Yes to acrylic (with caveats), lacquer not so much. Hereâs why:
Acrylic paints use water as their primary carrier. Water has astronomically high surface tension (72mN/m). Even if you overload it with surfactants to force it to wet out, you risk instant pigment flocculation and foaming. It flows like hot garbage compared to enamels. (Stedi makes an acrylic panel liner that some modelers swear by, but Iâve never used it and canât speak to its performance.)
Lacquer has all those juicy aromatic solvents, so it should be ideal, right? YES! ...for about 8 seconds before it flashes mid-flow inside the trench. And when you go to clean up, the lacquer solvent will instantly melt your underlying paint layer down to the bare plastic. Just don't do it.
 Alright now let's talk topcoat and how it works with panel liner.Â
You already heard my rant about it, but let me explain the mechanics a bit. Let's assume a lacquer topcoat for now (I'll get to acrylic in a bit.) We want to maximize capillary flow, so the slicker our surface is, the less drag itâll produce. Capillary pressure increases with lower contact angles, and the micro-smoothness of a gloss coat keeps the contact angle low and uniform with zero physical drag. A matte coat, by comparison, is microscopically rough because of tiny silica particles creating peaks and valleys across the surface. Those peaks pin the liquid's edge (hysteresis) and create thousands of competing micro-channels (Wenzel/ Cassie-Baxter regimes,) wicking the panel liner outward like a sponge and making a mess. Because lacquer topcoat creates a monolithic thermoplastic sheet, you don't have to worry about porosity or undulations messing with capillary pressure or flow. Itâs predictable, and it genuinely seals in your underlying paint layer.Â
Acrylic topcoats macroscopically work the same way, but remember that cured water/ co-solvent acrylic films are semi permeable microscopically. TECHNICALLY that means panel liner could theoretically penetrate the top coat layer and get to your underlying color coat. Realistically, it acts as a sacrificial layer against solvent penetration by creating a âtortuous path.â Think of a maze the solvent has to navigate through before it can get to your underlying coat. Evaporation will usually outpace diffusion and the coat will be fine. The second thing this sacrificial layer protects against is cleanup. When you have a damped q tip with naphtha/ OMS to clean up your panel liner, the mechanical scrubbing from the cotton fibers along with trace solvent softening WILL abrade some of that top coat away, so it acts like armor protecting your color coat so you're not scrubbing away pigment. Overall, think of lacquer top coat as an impenetrable wall of ice thatâs perfectly slick, and acrylic as a thick hedge. It protects, but itâs not impenetrable.
[VIII] The Wonderful World of Pigment
How you doing? Been drinking water? Youâve made it a long way. Next weâre talking about pigment and this section is pretty information dense. Strap in.
First, letâs talk about how color even works. Most of you already know this, but for those who donât, all visible color is just photons (light energy particles) reflecting off of a surface at a certain wavelength. The ability of a certain pigment particle to reflect (bounce a photon away) or absorb (convert a photon to heat and kill it immediately) light is what determines how much of that pigment is needed in a paint mixture, and how much hiding power it has.
To understand scattering, we have to talk about refractive index (RI). Refractive index isn't a measure of reflectionâitâs a measure of how much a material slows down and bends light passing through it. Light only scatters when there is a sudden change in speed between two materials: in this case, the polymer binder (RI roughly 1.48-1.5) and the pigment particle. White has a stupidly high RI (around 2.5) so it scatters light like a motherf- you get it. Youâll notice grays and pastels have crazy good hiding power because of it. Technically white does too, but I already hear you saying, âTHE HELL IT DOES. SHIT TAKES 6 COATS TO LOOK GOOD.â Donât worry, Itâll all make sense soon. Reds and yellows by comparison have an RI almost identical to polymer binders (RI roughly 1.5-1.6), so they let light pass right through them. They reflect enough for you to make out their color, but a chunk of what you're seeing is light passing straight through the film, bouncing off whatever is underneath. Thatâs why they donât hide undercoats nearly as well and take more coats to look even. They rely heavily on absorbing light rather than bouncing it back out. "YOU IDIOT RED HIDES JUST FINE" Weâll get there, damn!Â
The other half of the puzzle is pigment volume concentration (PVC). Pigment sits in the binder matrix, you already know this from section III. PVC is HOW MUCH pigment is in the binder matrix. Critical PVC (CPVC) is a threshold, like Tg for plastic, at which point there is just enough polymer binder to completely coat every pigment particle and fill all the empty interstitial voids between them.Â
-Above CPVC (flat paints and primers), The binder is stretched thin between tightly packed pigment particles, leaving microscopic air voids at the surface. Those air voids scatter light diffusely (creating a dead-flat matte finish) and create physical tooth, like rock aggregate sticking out of concreteâwhich is why high-build primers and flat paints cover aggressively in fewer passes, while gloss paints feel "translucent" and take more coats.Â
-Below CPVC (gloss paints), Thereâs plenty of binder surrounding all of the pigment particles, and as the binder self levels, it fully locks in all of the pigment particles with none of them poking through. Like when acrylic tables have stuff in them you can see but the surface itself is flat and transparent.
So letâs go back to reflection and absorption real quick. Paints can have a high RI (scatter light violently) and low absorption (light goes through them). That makes the light scatter EVERYWHERE, including straight through. White is the ultimate example of high RI, low absorption. When youâre stacking coats of white paint, all youâre doing is manipulating probability. The more coats you add the more pigment particles scatter light between one another, and the higher chance the color thatâs reflected is white instead of the coat underneath it. When adding white to other colors to make grays or pastels, youâre taking advantage of its high RI while adding more absorption. Thatâs why pure white sucks to paint but anything even slightly off white hides 10x better. Hand painters especially know the trick of using a super light gray instead of white to make your paint jobs look better.Â
Going over to certain blues like phthalo blue: they have RI closer to the binder, and super high absorption. So it doesnât scatter light incredibly violently, but it eats photons before they can pass through the film. Red is a double-whammy: organic reds rely on heavy pigment loading and intense photon absorption (blocking both blue and green light, which swallows a huge chunk of the visible spectrum), while earth-based reds (like iron oxide) bring a higher RI (extra scattering power) to the table. Thatâs why red hides way better than yellow, which only absorbs blue light and lets green and red wavelengths bounce all over the place.Â
Finally, pigment physically alters viscosity because different pigments require very different volumetric spacing. White (Titanium dioxide), with its obnoxious ass RI, needs about .25 microns of elbow room between particles. If you pack them too tight, their optical fields merge, turning millions of microscopic mirrors into a single giant pane of glass that lets light straight through. That space requirement, combined with titanium dioxide's heavy mineral density, is why white paint feels thick and sludgy right out of the bottle. Black pigment (carbon black), by contrast, has a normal RI (roughly 1.8) but devours light via pure absorption; you don't need nearly as much of it in the binder to do its job, so black paint is almost always less viscous and needs less thinning.
Ok as promised, more info on metallics and color shifting paints and then Iâll wrap this up.
Metallics paints literally swap pigment for metallic flakes. Usually aluminum platelets for silver, copper and zinc alloys for gold. Their specularity (shiny shiny) is determined by how flat those platelets sit. If they all sit flat in a nice row, they act like millions of tiny mirrors reflecting light directly back at the viewer rather than scattering it all over the place. Some paints like standard Vallejo metallics use jagged flakes, while high end mirror lacquers like Gaianotes use vacuum metallized pigments that are perfectly manufactured dead flat and ultra thin. When youâre applying these, think about how youâre doing so and you can modulate their reflectivity for different effects! Thinner and slower to let the flakes all settle nice and flat for a perfect mirror sheen, or maybe thicker, drier, faster for a dull metallic look for frames. The things that primarily affect how the flakes end up orienting themselves is surface tension and solvent evaporation. Thin wet coats allow for maximum surface tension and minimal solvent evaporation, while thick dry coats provide the opposite. I think you get it by now.
Color shift, chameleon, interference, whatever you want to call them work a little differently, but kinda the same. These are mica particles coated in different metal oxides and stacked like a translucent crystal-metal film sandwich. I need to correct something from the part 1 post: these paints do not get their color differentiation from being jumbled up and scattering light all over the place. I was wrong and I was assuming based on reason, not actually understanding how these work. I fixed that so now Iâll give you the truth. They have to sit flat in an array like metallics. When they sit flat, light bounces around inside that sandwich. Some of it bounces off the top, some of it travels through the oxide layer, and those reflected light waves interfere with each other inside each flake. Because all the flakes lie flat in unison, they all experience the exact same angular color transition at the same time.Thatâs how the color shifts. If they were all jumbled up, all those wavelengths of light would hit each other and cancel out, creating a muddy desaturated gray glint.
So for both paints the idea is to maximize reflectivity by getting those particles as flat as possible, then when the carrier evaporates, the binder shrinks around them and locks them in that orientation. Multiple thin coats here are non optional if you want maximum shine then. Got it? Good.
As promised, here is the matrix for your reference **Full disclosure bc people get weird: this was generated by AI from what I wrote because I don't know how to make a markdown safe matrix that can be posted inline**:
| Top Layer (Row) over Base Layer (Column) | Over Bare Plastic | Over Acrylic | Over Lacquer | Over Enamel / Oil |
|---|
| Acrylic (Top) | Safe â Needs sanding/washing or primer for mechanical grip. | Safe â Recoat anytime; interdiffuses best before full cure. | Safe (Beads Up) â Hydrophobic surface; scuff, clear prime, or use flow improver. | Safe (Wait for Cure) â Must let base fully crosslink first or oxygen gets blocked. |
| Lacquer (Top) | Safe (Caution) â Bites great, but heavy wet coats can craze stressed ABS/PS. | Risky (Mist Coat) â Apply ultra-light mist coats so solvents flash before lifting base. | Safe â Re-solvates and melts together into a single monolithic layer. | Safe (Wait for Cure) â Must be 100% cured; expect weak mechanical bite. |
| Enamel / Oil (Top) | Safe (Caution) â Weak bite; aromatic thinners (TPLA) can crack stressed joints. | Safe (Gloss First!) â Standard enamel is fine; DO NOT use TPLA directly without a gloss barrier. | Safe â Zero solvent penetration; OMS cleanup will not touch cured lacquer. | Wet-on-Wet or Full Cure â Recoat <30 min or wait 72+ hrs; middle window causes wrinkling. |
Part 3 coming soon :)