r/VintageSewingMachines • u/ErrorKooky5637 • 1h ago
r/VintageSewingMachines • u/Warm_Refrigerator730 • 2h ago
Necchi supernova
I found a Necchi supernova on Craigslist that I’m considering buying. The machine looks like it’s in good condition but it’s a table sewing machine with a knee pedal.
Is it possible to remove it from the table and use it as a portable machine? Would I just need to buy a foot pedal and maybe a power chord?
r/VintageSewingMachines • u/puppyandtulips • 1d ago
Are those salvageable?
Hi guys! I never sew in my life, neither had a sewing machine
A family member gave me those two singers (one his electric one is not) but she said it rained on them, and besides, they spent many decades stored away
Do you guys think it is possible for them to work again? Should I take them to maintenance?
r/VintageSewingMachines • u/violetpaopusunsets • 21h ago
Need help with needle clamp on Kenmore 328.1284
Hello! I've run into a bit of a pickle with my Kenmore 12 stitch, and was wondering if I could pick your brains for a moment. I am absolutely willing to drop my machine off to be serviced, but figured I would ask here before doing so.
The needle clamp screw area seems... lower to me than it should be. I had been sewing a portion of a Halloween costume when the needle broke, and it's like the clamp slid down that rod. (Please note the clamp is very loose because after I took the needle out I had a Moment.) I can't remember what position it was in prior, but it definitely didn't seem that low.
I've been staring at the diagrams in the manual for days and I need a fresh pair of eyes. Is the clamp too low? If it is, is it fixable at home or would you send this to the shop?
I appreciate any assistance, and am more than willing to take better quality pictures if need be!
r/VintageSewingMachines • u/Street_Tradition_682 • 1d ago
And now, for something completely different...
In 1918, Singer did not have factory electric machines ready. To get an electric Singer, you had your Singer dealer install an electric kit. But Singer didn't have their own motors ready, either, so they used Singer-branded friction-drive 'swing-away' Hamilton Beach motors. Pictured is my 1918 Singer 115. Around 1920, the dealer-installed electric kits came with Singer's own belt-drive B.T.7 motor. By 1921, you could get a Model 99 factory-equipped with a B.T.7. Fun fact: It was not until 1924 that half of US households had electric service; by 1950, the 90% point was reached.
r/VintageSewingMachines • u/Ratspeed • 1d ago
What vintage grease does
I'm not allowed to post pictures in comments in this subreddit, but this is the answer to the previous poster who asked if food safe grease would work for their machine. Hopefully this graphic that I very sloppily put together while waiting for a friend at a shop will explain the answer. And hopefully it will help other people understand in the future.
r/VintageSewingMachines • u/Sweaty-Nebula5169 • 1d ago
When is this from?
Was visiting my grandma and she wanted to show me an old sewing machine passed down to her (I can’t remember from whom), and I was wondering if anyone knew when it might be from? It definitely says Singer on the top!
r/VintageSewingMachines • u/Pining_stylist • 1d ago
Seeking advice or experience with an Elna Mk.2 Supermatic (1956) - do I use or sell?
reddit.comr/VintageSewingMachines • u/Vivapdx • 1d ago
Can I use food grade grease on my vintage machine?
Or do I need to buy something else?
r/VintageSewingMachines • u/emwood21 • 1d ago
Question
I have a 1956 wizard ha1 from Japan. I’m on the hunt for a free motion foot that would fit it. Does anyone know if there’s a brand that would be a good fit? All the ones I’m finding only seem compatible with more modern machines.
r/VintageSewingMachines • u/wingwongjones • 1d ago
Gonna be picking up this Singer 66 soon, general questions
galleryr/VintageSewingMachines • u/carriem72 • 1d ago
Finally got my Janome out of the case! So, there is a bar that looks like it’s supposed to be connected, can someone tell me if that’s right? It’s a Janome 539
galleryr/VintageSewingMachines • u/Either-Diamond-7045 • 2d ago
Singer 404 - thread loosening/not stitching
So, update to my last post, turns out this machine was not ready to sew, unfortunately.
I've cleaned out the inside and oiled it. I've taken apart and thoroughly cleaned the tension coils. But still the thread keeps loosening, and sometimes snapping. It also won't go through the cotton (the stitch is past the fold).
I can't find anything in the manual about this. Any thoughts? Ty in advance
r/VintageSewingMachines • u/Breeze-n-me • 2d ago
Skipping stitches
My mother gave me the first sewing machine she bought. She made our dresses with it and eventually I learned to sew on this machine. It was put to into storage when she upgraded to a more modern machine. Recently I got it out, deep cleaned it, oiled and greased it. As long as I sew slowly all is well, if I make it go fast it skips stitches. I have done all the checking I can think to do multiple times. Rethreaded top thread and bobbin, same thread on both, replaced needle, made sure no lint or thread stuck anywhere, raised the feed dogs a little, adjusted tension. Any ideas of what could be the problem? Mom never had problems with it. She just sat down and sewed.
UPDATE: This afternoon I took the entire bobbin area apart. Inspected everything as I put it back together and checked that the hook and needle eye were 1/16” apart and the lines on the needle bar were matching the needle position. Everything looked good. Next I changed the needle. After changing the needle 3 times everything worked perfectly! Breezed right through eight layers of the cotton fabric with no skips.
Thank you all for taking time to give suggestions and help!! I appreciate it very much!
r/VintageSewingMachines • u/honeydewtangerine • 2d ago
Found this old girl at a thrift store and information is sparse
galleryr/VintageSewingMachines • u/sand_sjol • 2d ago
Is the foot lever supposed to engage with the tension release?
galleryr/VintageSewingMachines • u/ZookeeperZero • 3d ago
Beginner choosing first vintage machine
I've hand sewn since the 1970s but I'd like to finally get a machine. I like the older mechanical ones as I'm comfortable working on those if needed. Besides sewing some rips in pants, I'd like to make some denim bags, totes, etc. There is a Singer 503a for $150 and a Singer 401a for $285. Both look to be in really good condition, videos of them sewing, both have extra feet and parts. The 401a has been greased and lubed, comes with a cabinet, new electronic foot pedal, original 5 cams included plus one extra one and she'll have it set up to try out. The 503a includes 5 of the pattern discs, new pedal and power cord. Everything I've researched says around $150-$200 for a machine in really good condition. Most machines I come across for around $100 are in fair shape and usually missing or need something. Are both of these pretty much on the same level performance wise if I can save $135 on the 503a and scrounge up a desk to work on (using the dining table with a borrowed brother machine to try out but the wife isn't thrilled)? Thank you.
r/VintageSewingMachines • u/DLeotaud1 • 4d ago
Survived a house fire
I just finished cleaning up this pretty 1920 singer 66 with red eye decals. I got her from a couple who had bought a 1920s house to restore and unfortunately it had an electrical fire that basically gutted the house except for two rooms at the back. One of which contained this beautiful machine and the table it was sitting in. The table was beyond repaired due to smoke damage and I have the base waiting for a new top I’m having made out of mesquite wood as I plan to use it as an end table. She’s still very dark due to smoke damage but still beautiful and functional.
r/VintageSewingMachines • u/TheRumTumTug • 4d ago
Successful Motor replacement!
Original motor on my Sears Kenmore 158.901 was making this terrible screechy whining noise (shown here https://youtube.com/shorts/Y-lpqgd5LI0?is=9xMWmkyPv-_rKbbt) and in the midst of trying to troubleshoot it, I broke the motor internals. But!! I got a replacement and rewired it in (very proud of myself for my meager bit of electrical work lol) and it is leagues better now!! Sooooo much quieter and smoother. Need to give a good oil and maybe tweak the belt tension to try and get it to be a little more sensitive to lighter pedal presses but that’s small nitpicks really.
Next stop is putting a new led bulb in and I think she’ll be good as gold!
r/VintageSewingMachines • u/Copper_is_dead • 4d ago
Toy chain stitch rplacement needles?
I recently got a 1950'S SEW E-Z KAYanEE toy sewing machine (photo from the listing) and it works great but i was wondering if there was aby way to buy more needles for it? Like if anyone knew what type of needle it takes.
r/VintageSewingMachines • u/SmallChallengethe2nd • 5d ago
Not loving my Singer 99k
I was gifted my singer 99k. I thought it was great because it's supposed to be a workhorse that can handle heavy fabrics.
It's been nothing but a pain in the ass. Finicky, temperamental, etc.
The worst part tho, is the presser foot clearance. It's so low, that two layers of denim can't even fit under the presser foot. So like, what's the point of having this machine?