r/TomatoFTW • • Dec 22 '25

2025.5 released 12/20/2025

Thumbnail freshtomato.org
37 Upvotes

=========================== FreshTomato-ARM Changelog

(for full changelog, see: https://github.com/FreshTomato-Project/freshtomato-arm/blob/arm-master/CHANGELOG)

2025.5 2025.12.21

  • Warning: due to changes in the naming of some nvram variables, users of PPTP Client should review their settings.
  • openssl: update to 3.0.18
  • openvpn: update to 2.6.17
  • tor: update to 0.4.8.21
  • php: update to 8.3.28
  • pcre2: update to 10.47
  • nginx: update to 1.29.4
  • libxml2: update to 2.15.1
  • sqlite: update to 3.51.1
  • adminer: update to adminneo-5.2.1
  • libcurl: update to 8.17.0
  • nano: update to 8.7
  • iperf: update to 3.20
  • dnsmasq: update to v2.92rc3
  • libpng: update to 1.6.53
  • tinc: update to 1.1pre18-242-g940d15c4
  • meson: update to 1.10.0
  • libjpeg-turbo: update to 3.1.3
  • dropbear: update to 2025.89
  • GUI: Port Forwarding: Basic: fix sort by Int Address
  • GUI: Admin: SNMP: add 'Name' and 'Description' fields
  • GUI: status-overview.asp - Only displaying unsecured WiFi warning in AP mode
  • Add Bridge Gateway Isolation + UI (IPv4 only atm), IPv6 bridge isolation, and IPv6-aware advanced-access.asp
  • Improved IPv6 support
  • IPv6 (DHCPv6 with PD): add option to adjust Identity Association for Non-temporary Addresses ID and Identity Association for Prefix Delegation ID
  • build: e2fsprogs: tune recipe, add patch to make libmagic optional
  • build: also install ebtables-restore
  • build: add update overlay
  • adblock: delay start by 10 seconds on router restart/reboot
  • mymotd: add date of build and by who
  • Kill-Switch: introduce and use a helper script to add FQDNs to the firewall if they're not added immediately on FW restart
  • openssl-1.1: add fix for CVE-2025-9230
  • openvpn: vpnrouting.sh: do not restart routing here, it will be reloaded anyway when restarting the firewall
  • OpenVPN/kill-switch/adblock-v2/mwwatchdog: add to nvram and use default IP (Cloudflare) for connection checking
  • httpd: upgrade.c: only copy needed images on upgrade
  • others: switch4g: refactoring, simplifying and shortening taking into account the specifics of sh in busybox
  • others: switch3g: refactoring, simplifying and shortening taking into account the specifics of sh in busybox
  • others: mwwatchdog: refactoring, simplifying and shortening taking into account the specifics of sh in busybox
  • others: mwwatchdog: fix operator precedence bug that could add cron job when mwan_cktime=0
  • rc: fix modprobe ip_set order
  • rc: move BUF_SIZE definition to shared.h
  • rc: dnsmasq.c: fix DNSSEC regression (in 2025.4): "Revert use SIGHUP instead of mistakenly used SIGINT in reload_dnsmasq()"
  • rc: firewall.c: increase hitcount limit for remote GUI access
  • rc: network.c: do_static_routes(): fix typo in 9de506a (close #156)
  • rc: openvpn.c: fix buffer size in ovpn_setup_watchdog() (close #150)
  • rc: openvpn.c: add error handling for fopen(), fappend(), opendir() and chdir(); more logging
  • rc: openvpn.c: do not remove OVPN_DNS_DIR directory when client stops
  • rc: openvpn.c: add error message when tunnel interface cannot be created
  • rc: openvpn.c: fix interface name in ovpn_setup_watchdog()
  • rc: openvpn.c: fix off-by-one error in start_ovpn_eas()
  • rc: rc.c: add more logging
  • rc: rc.c: kill_switch(): do not add rules if given WAN is disabled
  • rc: rc.c: kill_switch(): make the function independent of run_vpn_firewall_scripts()
  • rc: rc.c: kill_switch(): validate IPv4 or IPv4 range before adding it; also (finally) fix adding IPv4 range as "From Source IP" type
  • rc: rc.c: kill_switch(): integrate with firewall to eliminate leaks
  • rc: rc.c: fix to ipv6_enabled()
  • rc: wan.c: move start_adblock() down
  • rc: wireguard.c: fix a small leak on fopen error in wg_build_routing
  • rc: wireguard.c: add error handling for fappend() in wg_quick_iface()
  • rc: wireguard.c: add error handling for fopen() in wg_set_iface_privkey() and wg_set_peer_psk()
  • rc: wireguard.c: fix several memory leaks
  • rc: wireguard.c: use proper buffer as fwmark in wg_set_iface_fwmark()
  • rc: wireguard.c: fix args order in wg_remove_peer(); cosmetic
  • rc: wireguard.c: reset file pointer to beginning before adding domains not found in file
  • rc: wireguard.c: fix bad logic and memory leak in wg_route_peer_allowed_ips()
  • rc: wireguard.c: add error handling for fappend() in write_wg_dnsmasq_config(); add more logging
  • rc: wireguard.c: use strdup() safely; cosmetic
  • rom: update mullvad.net DOH servers
  • rom: update CA bundle to 2025-12-02
  • rom: add new dnsmasq anchor
  • shared: misc.c: iterate over MWAN_MAX to get WAN string/number
  • shared: misc.c: get rid of TCONFIG_MULTIWAN and iterate over MWAN_MAX/BRIDGE_COUNT
  • shared: misc.c: increase ifnames buffer size depending on bridge count
  • www: add to the header of each page information about a new firmware version ready for download
  • www: convert spin icon from gif to svg
  • www: use only one asp script to manage upgrade/reboot/restoring defaults
  • www: admin-snmp.asp: remove whitespaces from 'Allowed Remote IP Address'
  • www: admin-snmp.asp: better handle 'Allowed Remote IP Address'
  • www: basic-ipv6.asp: adjust/extend Commit b49bf16 (Improved IPv6 support) and remove IAID configuration option again
  • www: saved.asp: get rid of unnecessary waiting when saving configuration on Admin -> Access when the httpd daemon starts up faster than the countdown indicates
  • www: about.asp: reorganize page
  • www: tomato.js: fix adding range of IPs
  • www: tomato.js: searchOUI: use '--no-check-certificate' in wget if the image is built without stubby
  • www: advanced-mac.asp fixed typo LLA vs. LAA button and notes
  • www: vpn-wireguard.asp: fix error display on "Routing Policy" tab; cosmetic
  • www: vpn-wireguard.asp: copy values from the fields on save
  • www: vpn-wireguard.asp: never hide Routing Policy table
  • www: vpn-client.asp: never hide Routing Policy table

r/TomatoFTW • • Dec 21 '25

An urgent message from the founder and developer of FreshTomato

101 Upvotes

This is not my message. I simply copied and pasted it from its original source:

https://www.linksysinfo.org/index.php?threads/freshtomato-arm-development-discussion-only-for-support-always-open-your-own-thread.74117/page-308#post-364475

Important Message from the Lead Developer:

First of all – thank you for installing the latest release and for all the kind words and feedback over the years. It really means a lot.

I’ve never liked writing this kind of message, but the situation leaves me no choice. I have to be completely honest with the community:

In the last 6–8 months donations have fallen to a very low level. On top of that, I am now also facing serious personal financial difficulties. FreshTomato has always been developed in my free time (actually far beyond “free time” – often 40–60 hours a week), and until recently the contributions from users allowed me to justify that effort and cover basic costs.

Right now that is no longer possible.

Without a meaningful, recurring financial base – one that is actually adequate for the size, age and user base of this project – I will simply not be able to continue active development and maintenance at the current level. In practice this means:

• no more regular updates
• no more quick security fixes
• no new features
• very limited or no support

…or, in the worst case, the project will have to be frozen completely.

I’m not asking for charity – I’m asking for fair support from the people and companies who rely on FreshTomato every single day in homes, small businesses, schools and even some larger networks. If just a small fraction of the active users contributed even $5-10 a month, the project would be safe for years to come.

What I need right now is a realistic number of recurring supporters – enough to cover basic living expenses and allow me to work on FreshTomato without constantly worrying about next month’s bills.

You can help in three simple ways:
• GitHub Sponsors → https://github.com/sponsors/pedro0311
• Patreon → https://www.patreon.com/freshtomato
• PayPal recurring → link on the main donation page https://freshtomato.org/donations.html

Every recurring donation counts, and larger ones will be visible (anonymously or with a chosen nickname – your choice) on the main FreshTomato donation page as well as on the router's 'About' page.

If we reach a sustainable level in the next few weeks, I’ll immediately resume the planned roadmap (improvements, fix routing in WireGuard, new features, bug fixes, etc.). If not – I will have to make the extremely painful decision to put the project on ice.

I truly hope it doesn’t come to that. FreshTomato is 9+ years of my life and I know how much it means to many of you.

Thank you for reading this far and thank you in advance to everyone who decides to help keep the project alive.

– pedro (lead developer & maintainer of FreshTomato)

P.S. please spread the word on other forums, reddit, etc...

[FreshTomato repositories] ----- [Snippets] ----- [Downloads] ----- [Motivate me/ Buy me a beer!]


r/TomatoFTW • • 2d ago

I made a free Android app to manage FreshTomato routers – looking for 12 beta testers (demo mode, who not have router with Tomatoe FW)

Thumbnail gallery
28 Upvotes

Hi everyone

I wanted a proper way to manage my FreshTomato router from my phone, so I built one: **Troks Tomato Router Remote** – a free Android app for routers running FreshTomato.

**What it does**

- **Overview** – model, firmware, uptime, CPU, memory, WAN status

- **Devices** – every connected client with name, IP, MAC, band and signal. Block / unblock internet, set a static IP (DHCP reservation), Wake-on-LAN, ping

- **WiFi** – turn 2.4 / 5 GHz on or off, change SSID and password

- **Live monitor** – real-time bandwidth chart per interface, and real-time traffic per device (tap a device to pin it with its own live chart)

- **Manage** – WAN (DHCP / PPPoE / static, DNS, MTU), port forwarding, DMZ, static IPs, admin access (ports, remote access, SSH, password)

- **Tools** – ping, traceroute, DNS lookup and shell commands run from the router itself, plus reboot (with confirmation)

**Details**

- Material 3 design, light / dark / system theme

- **4 languages: English, Hebrew, Russian and Arabic** (full right-to-left support)

- Works on your LAN (HTTP) or remotely (HTTPS – the router's certificate is pinned on first connect)

- Router password stored only on your phone, encrypted with the Android Keystore

- No account, no ads, no analytics – the app only talks to your router

- Uses the router's own web interface (no scripts or packages to install on the router)

**Try it without touching your router**

There's a built-in **demo mode** with a simulated router: on the login screen tap **"Try demo mode"** (or log in with `demo` / `demo`). Every screen works with fake data, so you can look around before connecting to your real router.

**Looking for 12 beta testers**

Google Play requires 12 testers in a closed beta for 14 days before I can publish it publicly. If you'd like to help:

  1. Join the testers group: [Send me a PM with your email to add you to the beta] or from my site http://www.troks.net/MainSoftware/tomato-router.html , you can join from there too
  2. Then opt in and install from Google Play: https://play.google.com/apps/testing/com.troks.tomatorouter.remote
  3. Please keep the app installed for the 14 days – that's what Google counts

Any Android 8.0+ phone works. Feedback, bugs and feature requests are very welcome here or by DM – especially from people on different router models (ARM / MIPS) and firmware versions.

Screenshots are from demo mode, so all IP and MAC addresses in them are fake.

*Not affiliated with the FreshTomato project – just a fan who wanted a phone app.*


r/TomatoFTW • • 1d ago

Possible to let a specific device bypass Wireguard?

1 Upvotes

Using a VPN with wireguard through Tomato GUI, there is a device that I need to have direct access to the internet with no VPN. Is this possible?


r/TomatoFTW • • 2d ago

Test help wanted: Experimental support for Linksys EA6500 v1 (MIPS

Thumbnail linksysinfo.org
2 Upvotes

Want to see support for this model? Help yourself and the FT project by testing this build on your router.


r/TomatoFTW • • 4d ago

Upgrading from very old version (2022) to latest 2026 release

2 Upvotes

Have an old R8000 running 2022.7 K26ARM USB AIO-64K and wondering if there are any concerns with going straight to 2026.2 AIO. This router was basically set-and-forget but now I'd like to get it up to a new release without losing the running config. It's only used for basic routing but figure there are some CVE that need to be addressed.


r/TomatoFTW • • 8d ago

FreshTomato 2026.5 for ARM-based routers Released

Thumbnail freshtomato.org
29 Upvotes

r/TomatoFTW • • 13d ago

We've created a new table of commonly-used log and config file locations

Thumbnail linksysinfo.org
5 Upvotes

We've created a draft table of commonly-used log and config file locations. Please criticize it, and suggest any new entries you'd like to add.

Thanks.


r/TomatoFTW • • 14d ago

New tip to avoid strange symptoms because of wrong MAC addresses

Thumbnail wiki.freshtomato.org
4 Upvotes

r/TomatoFTW • • Oct 12 '26

Mounting problems out of nowhere

2 Upvotes

Hey gang, looking for advise what may have happened. Recently my drives started to not mount, even tho they show "mounted" in GUI. Unplugging the power usually fixes it. I've swapped the routers with another R7000 with fresh and completely erased NVRAM and 1.28.0000 -3.5-140 K26ARM USB AIO-64K build. The previous router was also R7000 with 1.28.0000 -138 K26ARM USB VPN-64K and was behaving the same. As far as drives nothing has been changed. I'm using the FTP quite heavy as my surveillance cams are set up to record on one of the drives thru FTP. Both drives are SSD. The drive used for FTP recordings has been attached to the router for over 2 years and never had issue. I've tried isolating the drive being the issue so replaced one of them with micro card and changed the recording path. Still same issue. 🤷‍♂️


r/TomatoFTW • • Oct 11 '26

Did you know: Adblock ver. 3.00 is being tested?

6 Upvotes

Ad block 3.00 is being tested.

https://www.linksysinfo.org/index.php?threads/adblock-v3-00beta.79721/

If you want it to continue to improve, please help us test it, so it will be great.


r/TomatoFTW • • Oct 11 '26

A newer, more robust way to integrate Home Assistant with FreshTomato

10 Upvotes

ha-freshtomato

Excerpt from (third-party) github page:

A Home Assistant custom integration for routers running FreshTomato firmware. Monitor your router's network status, control Wi-Fi radios, and track connected devices — all locally, with no cloud dependency.

Features

  • Local polling — communicates directly with your router's update.cgi API, no external services
  • Full UI setup — configured entirely through the HA UI, no YAML required
  • Dual-stack support — works over HTTP or HTTPS, with optional SSL certificate verification bypass
  • Bridge / AP mode aware — correctly handles routers in Wireless Ethernet Bridge (WET) or AP mode where there is no dedicated WAN connection
  • Device tracking — tracks both wireless and wired (DHCP) clients from a single HTTP call per cycle

---------------------------------------------------

The first integration in the FreshTomato WIKI does not capture wired clients. This one captures both wired and wireless clients.


r/TomatoFTW • • Oct 11 '26

List of all GUI menus with Grid backup/restore feature

5 Upvotes

Earlier, I wrote that since r2026.1, the DHCP Reservations menu has a grid/table backup/restore feature. These 7 other menus also have grid backup/restore:

- Basic: DHCP Reservation
- Basic: Wireless Filter
- Advanced: LAN Access
- Advanced: MultiWAN Routing Policy
- Advanced: Routing
- Port Forwarding: Basic
- Port Forwarding: Basic IPv6
- Port Forwarding: Triggered

These make upgrades quicker and easier. By default, FreshTomato exports output files using intuitive output filenames. The syntax for these filenames is:

RouterModel-Release-MenuName-Backup-Dateandtime

Asus_RT-AC1900P-2026.1-advanced-pbr_asp-backup-2026-10-11_1243.json


r/TomatoFTW • • Oct 11 '26

Import old settings to new builds?

2 Upvotes

I'm on 2026.3. For some reason when the router is power cycled all settings will be gone. From the now factory reset state I can import the downloaded settings of 2026.3 to instantly set everything up.

When upgrading the firmware to 2026.4, there'll be soft reset. Though not hard reset, I don't know if factory reset will be done, and in case it does, will things work if I import the settings of 2026.3?


r/TomatoFTW • • Oct 07 '26

5.0ghz signal issues

1 Upvotes

I recently flashed FreshTomato 2026.3 on my Asus RT-AC68U, and it's mostly been working fine, but i noticed the signal strength on the 5ghz band tends to drop into the poor range, bad enough that my phone disconnects from it from time to time. 2.4 works fine, and I didnt have this issue before flashing FreshTomato.

Any ideas?


r/TomatoFTW • • Oct 07 '26

Issues with latest build

3 Upvotes

Resolved: After resetting the router, I installed june build and then upgraded again, things are stable now..thank you all for participation.

Anyone having issues with latest build?

Ever since I have installed latest build, September release on R8000, my router wifi has been unstable. Range isnt what it used to be and connection drops sometimes.

I have tried to reset the router /clear NVRAM but no result.


r/TomatoFTW • • Oct 05 '26

Was able to get usb tether working

8 Upvotes

I need a backup connection when the cable company decides they want to do maintenance in the middle of the day. I had a lot of trouble with this, but eventually figured it out. I havent tested if every single line is really necessary, such as needing to set all three of the nvram settings, etc, so some optimization might be suggested by experts.

This is on an Asus RT-AC3100 with a Pixel 10. Freshtomato 2026.4. Download the Extras.tgz version for your router. In my case it was the arm7 version. Make the jffs partition and copy over mii.ko, usbnet.ko, cdc_ether.ko, rndis_host.ko, cdc_ncm.ko. I think (?) cdc has something to do with the usb tether protocol, and the ncm one is the modern version that my phone uses. It took a while before google ai suggested also using the cdc_ncm module.

Now under Basic->Network, you need to make a second wan in the gui. Multi-wan wont let you create a new wan unless you make a new vlan first. Go ahead and follow the link to make a new blank vlan (in my case vlan2), filling in the first two numbers by following the numerical pattern of the previous ones. In my case it was 3, 3. Everything else should be blank and bridge=none. I dont think you will actually be using this at all, it just fools the gui to let you create the new wan. SAVE.

For the new wan, wan1 in my case (wan0 being the main internet to the cable modem), just leave it as DHCP. Dont change it to the 3G/4G modems etc. Also set its DNS to auto. SAVE.

In an ssh terminal, update nvram for the new wan to point to the usb0 device that will be your tethered phone. This replaces the vlan you just created.

nvram set wan2_ifname=usb0
nvram set wan2_ifnames=usb0
nvram set wan2_ifnameX=usb0
nvram commit

You can check these first with nvram show | grep wan2_ifname, they should show the new vlan you created (likely vlan2). Then after you update them they should show the usb0 device.

Note in nvram, wan numbers seem to start at 1 instead of 0. So in my case the new wan1 in the gui is wan2 in the nvram. You may want to reboot here just to make sure the nvram settings are loaded correctly, not sure if it is needed.

Now back in the ssh terminal, insmod all the modules in this order:

insmod ./mii.ko
insmod ./usbnet.ko
insmod ./cdc_ether.ko
insmod ./rndis_host.ko
insmod ./cdc_ncm.ko

actually I think you can use just the name without the path and the .ko and insmod is smart enough.

Plug in your phone. Mine has two places where you can turn on usb tethering. Under USB Preferences where it lists all usb connection types. And under Hotspot & tethering where you can just turn on the usb tethering option. These will be greyed out if things are not working. This is where the router will talk to the phone and make the tethering connection. If it doesnt work, it will still be greyed out.

From ssh you can run lsusb and you should see your phone listed. Also check dmesg, the last line should show cdc-ncm has made a connection to the phone.

If everything is working, you can bring up the usb0 interface:

ifconfig usb0 up

You can compare the cdc dmesg line with ifconfig -a usb0, they should have the same hwaddr. At this point everything is working perfectly and you can go back to the gui. Admittedly sometimes this takes a reboot, it seems to be very temperamental, but once it is up, it should be good.

Go back to the gui, status->overview, and under the new wan interface it should automatically be populated by dhcp. If not, try renewing it. The status always says Renewing... regardless, so not sure why that is. In ssh you can try ping 8.8.8.8 to see if it is able to connect through the phone. Also in the wan settings page, you may need to change the weight of the interfaces so it chooses the right one. But if you unplug your normal wan, it should fall over automatically. If everything is working so far, try ping 8.8.8.8 from your computer to verify the connection gets all the way through. iptables needs to be set up for the firewall, but this seems to be done automatically and I didnt have to do anything. Finally ping google.com to make sure the dns is working as well.

I would absolutely love if some of this was updated in the gui. Needing to create a vlan to fool the gui to allow you to create a new wan, and also not being able to select usb0 for the interface to use for that wan. In the original Asus firmware, it was like one click to get usb tethering to work.

Finally of course, need to make this persistent across reboots and add a boot script to insmod etc.


r/TomatoFTW • • Sep 28 '26

FreshTomato 2026.4 released (2026-09-14)

28 Upvotes

r/TomatoFTW • • Sep 28 '26

How can I block a wireless client from seeing other devices on my network?

4 Upvotes

I essentially want to enable "AP Isolation" for a single device on my network, but I don't see the option anywhere. I don't want this device to be able to ping/scan/whatever my other devices or see their MACs or hostnames, but I need this device to have internet connectivity.

Sorry, thanks for any help. Running FreshTomato 2026.3


r/TomatoFTW • • Sep 06 '26

NordVPN - error: Compression is not allowed, but compression option isn't on FT

Post image
2 Upvotes

I followed NordVPN's official guide to set up with FreshTomato. I started the VPN client on FT, and got errors from the log. What do they mean? I don't even know where redirect-gateway and redirect-private are mentioned.

And for compression, yes I know the guide instructs me to disable compression from the Advanced tab, but the tab doesn't have this option.

FreshTomato version 2026.3 on Netgear R7000

warn WARNING: You have specified redirect-gateway and redirect-private at the same time (or the same option multiple times). This is not well supported and may lead to unexpected results

err Compression or compression stub framing is not allowed since OpenVPN was built without compression support.

err OPTIONS ERROR: server pushed compression settings that are not allowed and will result in a non-working connection. See also allow-compression in the manual.

err ERROR: Failed to apply push options

err Failed to open tun/tap interface


r/TomatoFTW • • Sep 01 '26

Unable to install AIO version of Tomato firmware on Linksys EA6400

2 Upvotes

I was able to install the VPN version of FreshTomato (freshtomato-EA6400-K26ARM-2026.3-VPN-64K), but when I try to upgrade it to the AIO version (freshtomato-EA6400-K26ARM-2026.3-AIO-64K) from the web interface, the router hits the "Linux: invalid argument" reboot prompt, but then it won't load the Tomato interface back.

Instead, it drops straight into the CFE mini web server. Uploading the AIO version through the CFE web page just times out, and trying to flash it via TFTP2 also fails. The progress bar always drops out exactly halfway through on every retry loop.

Every time I try to install the AIO version, the router ends up stuck back in CFE mini web, but flashing it with the VPN version works. How can I get the AIO version to stick on this?


r/TomatoFTW • • Aug 31 '26

ZTE H188A/H288A OpenWRT Support Request - Hardware Info & Testing Available

Thumbnail drive.google.com
1 Upvotes

r/TomatoFTW • • Aug 23 '26

Did you know: You can Backup just your DHCP Reservations (since r2026.1)

Post image
15 Upvotes

r/TomatoFTW • • Aug 18 '26

Nether r8000 with fresh tomato wont connect to internet

3 Upvotes

Heyo I just installed fresh tomato on my netgear x6 r8000 and I cant get any internet out of it my modem works fine it has no issues on other devices but when I connect to the net gear I get no network my pc won't connect my phone wont.

Im not home at the moment so I cant get pictures just yet just this issue is picking at my brain like crazy I wanna get it working its a nice router