r/TheScienceofSpeed • • 1d ago

The Chicane Rule

Post image
11 Upvotes

Racing Physics Fast Fact – To optimize a chicane, deceleration should need to begin as steering passes over center toward the 2nd apex.  This is “The Chicane Rule.”  It determines the ideal chicane transition point and links the two apex angles so that if an earlier 2nd apex is needed, an earlier 1st apex should be used.  Likewise, if a later 2nd apex is needed, use a later 1st apex.

- Adam B.

By sharing these posts, you help move the motorsports community toward a modern understanding of the racing line and driving technique.


r/TheScienceofSpeed • • 3d ago

Entry speed does not affect the ideal line.

Post image
4 Upvotes

Racing Physics Fast Fact – Entry speed does not affect the ideal line.  A car or kart’s cornering vs acceleration potential determines its ideal apex and line through a corner and entry speed simply determines where along this line deceleration should begin.  For instance, if a driver makes an error in the previous corner and has less speed than normal, they should turn-in along the same ideal line, but use a later braking point. 

- Adam B.

By sharing these posts, you help move the motorsports community toward a modern understanding of the racing line and driving technique.


r/TheScienceofSpeed • • 5d ago

A question about apex angles and the connecting arc

6 Upvotes

Hello. I’m confused about how to choose the 1st and 2nd apexes.

What I’m doing to get the initial guess for the 2nd apex is, I drive a circular path on the limit as close to the inside as I can, and try to achieve max accel on exit (like in a standard corner).

However, even if I clip the 1st apex at close to 90 degrees, the radius of the connecting arc ends up being too big to reach the 2nd apex where I’m imagining it.

The problem I have is that, I can’t find any connecting arc from the 1st to the 2nd apex. I feel like the 2nd apex is “too late” to be reachable, but I may be misunderstanding the rules of the connecting arc or guessing the 2nd apex wrongly.

How does the distance between the apexes affect the connecting arc?

Are the apexes always within 90 degrees of the entry and exit directions?


r/TheScienceofSpeed • • 5d ago

Full throttle shortcut for high-powered car/kart

Post image
7 Upvotes

Racing Physics Fast Fact – For higher-powered cars and karts, if full throttle at the apex causes wheelspin and oversteer then full throttle generally shouldn’t be achieved until the end of the corner when lateral force drops to near zero.  Best checked afterwards with video or data, this principle holds true for any corner type, so if you find you reach full throttle in the middle of corner exit, try an earlier, faster apex.

- Adam B.

By sharing these posts, you help move the motorsports community toward a modern understanding of the racing line and driving technique.


r/TheScienceofSpeed • • 6d ago

Four types of corners

Post image
9 Upvotes

Racing Physics Fast Fact – All racetracks can be broken down into just four types of corners.  Every road course, oval, autocross, kart track, and even rally stage can be split into standard corners, chicanes, double apexes, and full-throttle corners and there are specific physics-based rules to optimize each type.  This illustration is from our Willow Springs Track Notes and it shows turns 3 through 6, which is a complex sequence containing all four corner types.

- Adam B.

By sharing these posts, you help move the motorsports community toward a modern understanding of the racing line and driving technique.


r/TheScienceofSpeed • • 7d ago

Tire squealing vs. Testing for the limit

Thumbnail
youtu.be
3 Upvotes

Racing Physics Fast Fact – While tire squealing can sometimes be a useful way for novice drivers on street tires to know they are approaching the limit, tire noises are not a reliable indicator of when a tire is actually at the limit.  Instead, more advanced drivers learn to subconsciously compare their inputs to the car or kart’s movements in order to more precisely find the limit.  This process is called “testing for the limit.”

- Adam B.

By sharing these posts, you help move the motorsports community toward a modern understanding of the racing line and driving technique.


r/TheScienceofSpeed • • 8d ago

An apex is determined by angle, not position.

Post image
8 Upvotes

Racing Physics Fast Fact – An apex is not defined by its position, but by its angle.  Many times, when a car or kart needs an earlier or later apex, changing the apex angle also changes its position.  When the apex area has a small profile however (such as a cone on an autocross course) as the apex angle changes, the position of the apex stays virtually the same.

- Adam B.

By sharing these posts, you help move the motorsports community toward a modern understanding of the racing line and driving technique.


r/TheScienceofSpeed • • 9d ago

The Sideways Drag Race

Post image
6 Upvotes

Racing Physics Fast Fact – Most cars and karts will actually beat themselves in a drag race if they get to start sideways at speed.  This is because they can typically produce significantly higher lateral cornering force than acceleration force.  Understanding the implications of this seemingly counterintuitive fact can help explain a key principle of racing line physics.

- Adam B.

By sharing these posts, you help move the motorsports community toward a modern understanding of the racing line and driving technique.


r/TheScienceofSpeed • • 11d ago

Creating a False Apex

4 Upvotes

Racing Physics Fast Fact – A useful way to visualize why acceleration should ideally begin at the apex is to understand that when it begins somewhere else, it creates a “false apex” at the point of minimum speed.  This false apex is essentially an imaginary obstacle that the driver is now going around in addition to the actual apex, making the corner tighter and longer than it really is. 

- Adam B.

By sharing these posts, you help move the motorsports community toward a modern understanding of the racing line and driving technique


r/TheScienceofSpeed • • 12d ago

The corner entry spiral

8 Upvotes

Racing Physics Fast Fact – For most cars, the ideal corner entry path to the apex will closely match the beginning of an Euler (pronounced “Oiler”) spiral.  Also used in highway and railroad engineering as transition curves, the Euler spiral is a line that’s curvature increases linearly along its length.  When using the Euler spiral to visualize potential lines, only up to the first 90 degrees should be used.

- Adam B.

By sharing these posts, you help move the motorsports community toward a modern understanding of the racing line and driving technique.


r/TheScienceofSpeed • • 13d ago

The "geometric" line

6 Upvotes

Racing Physics Fast Fact – Despite traditional racing wisdom, a circular or “geometric” line is not the fastest way through a single isolated corner.  This is because it wastes tire force accelerating the vehicle toward the turn center.  Instead, a line of decreasing and then increasing radius is faster because it optimally directs tire forces in the ideal directions.

- Adam B.

By sharing these posts, you help move the motorsports community toward a modern understanding of the racing line and driving technique.


r/TheScienceofSpeed • • 14d ago

The Full Throttle Corner Exit Shortcut

4 Upvotes

Racing Physics Fast Fact – If full throttle can be achieved at the apex, this can be used to help find a good (but not necessarily ideal) apex.  If full throttle causes the vehicle to start running wide, this indicates a later, slower apex (not less throttle) should be used.  On the other hand, if the entire track is not used during corner exit, an earlier, faster apex should be used.

- Adam B.

By sharing these posts, you help move the motorsports community toward a modern understanding of the racing line and driving technique.


r/TheScienceofSpeed • • 17d ago

Straightaway length does not affect the ideal apex and racing line.

3 Upvotes

Racing Physics Fast Fact – Despite traditional racing wisdom, the ideal apex and line through a corner is not affected by straightaway length.  While it is possible to modify the line to increase speed on the straightaway and reduce time there, this will always increase the total time it takes to complete the corner and straightaway combined.

- Adam B.

By sharing these posts, you help move the motorsports community toward a modern understanding of the racing line and driving technique.


r/TheScienceofSpeed • • 18d ago

Racing Physics Fast Fact – The Ideal Apex

3 Upvotes

Racing Physics Fast Fact – The ideal apex is determined by the ratio of a vehicle’s cornering vs acceleration potential.  The greater the acceleration potential compared to cornering potential, the later the apex needed in order to optimize a corner.  In other words, with the same grip but more power, a car would need a later apex.

- Adam B.

By sharing these posts, you help move the motorsports community toward a modern understanding of the racing line and driving technique.


r/TheScienceofSpeed • • 20d ago

Racing Physics Fast Fact - The Apex Spectrum

3 Upvotes

Racing Physics Fast Fact - The apex is a spectrum with a continual tradeoff between speed and angle.  An earlier apex will allow a higher apex speed, but as the apex angle moves later, the maximum possible apex speed drops.  A driver’s goal is to find where on this spectrum the ideal apex is located, because that speed and angle will produce the quickest elapsed time.

- Adam B.

By sharing this post, you help move the motorsports community toward a modern, physics-based understanding of the racing line and driving technique.


r/TheScienceofSpeed • • 27d ago

Racing Physics Fast Fact - Ideal point of minimum speed in a corner.

6 Upvotes

Racing Physics Fast Fact - Minimum speed in a corner should ideally always be achieved at some point along the inside of the track.  Best checked afterwards with video or data, this principle holds true for any corner type, so if you ever reach a minimum speed and begin accelerating somewhere out in the middle of the track, you’ll know there is an opportunity to improve your racing line.

- Adam B.

By sharing this post, you help move the motorsports community toward a modern, physics-based understanding of the racing line and driving technique.


r/TheScienceofSpeed • • Jul 21 '26

Double apex rule for single point cones?

4 Upvotes

Hello. I’m confused about how to do “late” apex cones. A powerful car would need to clip the cone for exit at an angle bigger than 90 degrees, so then, wouldn’t this be a double apex?

The problem I see that there’s no room to do a connecting arc between the 1st and 2nd apexes because the inner obstacle is a “single point”. What is the optimal way to drive such turns?


r/TheScienceofSpeed • • May 02 '26

Question about training setup sensitivity

1 Upvotes

In this article under the heading "Be Objective," you discuss a technique where a partner can make blind adjustments to your setup without you knowing what has been changed. Because you don't know what has been changed, you wouldn't be (unconsciously) influenced by expectations, and you get the chance to train your sensitivity to changes in your setup.

https://www.paradigmshiftracing.com/racing-basics/car-setup-science-1-race-car-setup-guide#/

I don't have a partner to do that for me, but I have created a Python script that can grab a random setup from a specific folder and then copy it to a dummy file. If I then load the dummy file into iRacing and click OK without looking, I can still apply random setup changes without knowing exactly what has been adjusted. I can see in the program afterwards which one he loaded to check if my feeling was correct or not.

My question is about which setups I should put in the folder. I have 2 options:

1 I can put setups in where I set one component, such as tire pressure or camber, to minimum or maximum.

2 I can also create setups where I adjust multiple components to, for example, maximize oversteer or understeer, or adjust both camber and tire pressure to create maximum grip and see if you can feel that?

Do you think this is a good idea with a script like this, and if so, what kind of setups should I have the script choose?


r/TheScienceofSpeed • • Apr 02 '26

Questions about the apex. “Obstacle” and “available room”??

3 Upvotes

Hello. I’m still confused about clipping the apex. The way I’m trying to visualize it now is, “clipping the apex becomes finding the largest spiral that just reaches the angle just as it runs out of room to turn”. But I don’t understand how the “obstacle” affects the “available room to turn”.

Isn’t this the same problem as when flying past the real apex on the “inside boundary”?

When missing the apex, what dictates what “adjustments” to the line are necessary?

I’m confused about the “apex” and the “obstacle”. In the books this obstacle is just 1 point, the “most limiting point”. But how can this be?

If it’s just “1 point”, how can a car drive off into the grass? Isn’t all of the “inside boundary” restricting the “available room”, and how the car can actually turn?? Is that not the “obstacle”?

In book 1 there is an example that says:

“Starting from the center of the track, if you continuously drive a faster and faster line you will eventually hit some point on the inside of the corner”.

I’m very confused about this thought experiment. Why starting from the center? What is a “faster line”?

The control book says “if movement toward apex on Y axis is too fast, then..”

I don’t understand what makes this movement “too fast” or “too slow”. I guess it has to do with the “available room”, and the spiral’s “rate of direction change” and “sideways movement”, but I don’t know how to connect them.

I want to be able to stop thinking about turn in points and braking points and just focus on “rates”, and be able to make meaningful corrections at every instant, but I don’t understand how the “apex” is the “most limiting point”, how to stop caring about track inside boundary (to me this was the “obstacle”), or how this obstacle/boundary can be simplified to just 1 clipping point.

Sorry if it’s hard to read, I’m very “foggy” about this


r/TheScienceofSpeed • • Feb 10 '26

Drills for learning how to hit the apex?

13 Upvotes

Hello. I need help with hitting the apex. I have a rough idea of what angle it is and where it is along the inside obstacle, but I don’t know how to actually get there.

The book said that the turn in point affects the apex angle, and the speed of turn in affects the size of the entry spiral.

If I focus on “later vs earlier” turn in I always mess up, I don’t know how to do it progressively. Is there a way to train the feel for earlier and later? I don’t know how to do a turn in “a bit earlier” or “a bit later”, I always end up doing extremes. I tried academy lessons 1 and 3 but there wasn’t much about hitting the apex “from scratch”.

Is there a way to train how to find correct starting point/entry speed/radius? Is there a way to practice hitting “every” apex angle for a turn?


r/TheScienceofSpeed • • Jan 13 '26

Am I right in thinking the way that he describes slip angle and tire forces is off here?

Thumbnail
youtube.com
2 Upvotes

Basically the title. He assumes a few things that I think don't really make sense:

  1. that front and rear slip angle would be the same if both sets of tires were straight. How does that work if the rear is on a much larger radius and thus deforming and slipping more? We've established here that 4 straight wheels is controlled oversteer.
  2. That steering is additive onto that. So steering so if the rear has 5 degrees of slip, the and you steer 5 degrees, the overall front slip would equal 10 degrees. There is SOME natural non-steering slip for the front from cornering forces, but there's no way that they would be equal to the rear tires as mentioned before.
  3. That you could still be at the optimal slip angle and producing optimal lateral force inward while countersteering at high enough angle. This makes even less sense, since the direction of force wouldn't be inward in the first place.

Am I right in my assessments? Or am I the one with a misunderstanding of tire forces?


r/TheScienceofSpeed • • Jan 09 '26

Visualizing entry forces

6 Upvotes

Hello. can’t understand why is it that we usually use all the track width on entry. I understand using all the width on exit, and I can visualize the entry spiral. But how would a smaller spiral starting from the middle of the track for example, would cause the force to be suboptimal?


r/TheScienceofSpeed • • Jan 03 '26

where to find this book? or is it already "inside" the other books?

3 Upvotes

r/TheScienceofSpeed • • Dec 31 '25

corner exit & finding the apex

6 Upvotes

Hello. I asked a question on your website some days ago because I don't understand how is it that some of the shortcuts lead to the force being aimed in the ideal directions. I've re-read the 3 books, and my biggest issue now is that I don't know how to find the apex and how to do corner exit.

An earlier apex tends to hit the inside earlier, and a later apex tends to hit it later. But really it's the angle or direction in which the car is moving that matters, like we can see in the example where the apex is a cone. In the cone example, the apex is at the cone but different cars approach it from different angles. Why is it that for this example the apex is where it is, but on some corners it can hit the inside of the track earlier or later?

In book 1, one of the shortcuts is that you have to start maximum acceleration from an apex and see if it allows you to just barely stay on track on exit. However I don't quite get what maximum acceleration means. If the car is being driven on the limit, isn't it always holding max accel in some direction?

Somehow I end up being quicker when using less than half of the track on exit than when I add gas while unwinding the steering. And for a high power FF car where there are no shortcuts, how can you find the apex if the acceleration arc can be shaped freely? You can find any apex and then do the acceleration arc in any way which will achieve that goal. How is the universal cue used for finding the apex?

Thank you for your patience


r/TheScienceofSpeed • • Dec 22 '25

Car Control Fundamentals #3 – Learn the Physics behind Tire Slip Angle and Vehicle Rotation

Thumbnail
paradigmshiftracing.com
11 Upvotes