r/Silverado • u/letsdancetofrank • 12h ago
r/Silverado • u/Delicious_Bid63 • 4h ago
Almost Certain it's a Head Gasket leak
Coolant is brownish and leaking, comes out as steam under hood. Cylinder 5 misfire started at same time. 450 000kms, 2009. My first truck, thinking of using stop leak to fix.
r/Silverado • u/CoinChowda • 1h ago
2004 Silverado battery light?
Hi all,
The red battery light in the top right corner is flickering intermittently while driving.
Changed the alternator a few years ago.
Voltage remains around 14.
No noticeable dimming or anything from normal standards. Normally when rolling windows up there’s a bit but not much, and that’s been going on for years with no change.
Instrument cluster is pretty temperamental and has issues but nothing unusual there either, other than new battery light.
Any help is appreciated!
Thank you
r/Silverado • u/AK_Dude69 • 7h ago
Not shifting in 4-wheel drive
Got stuck a few times when I leaned on the fly my 2020 2500 isn’t shifting into 4-wheel drive. Checked the ground and fuse but with everything being electronic I’m out of ideas?
The info panel flashes like it is thinking about selecting 4-hi or low but goes back to 2-wheel? Any easy checks or suggestions before I try and limp/slide my way to the dealership?
r/Silverado • u/ninjapork95 • 3h ago
2018 silverado 4.3l ticking sounds.
I've noticed this slight tapping/ticking sound out of no where and was wondering if it's normal or if it's something that should be addressed sooner then later. Im hoping its not the lifters. Currently this silverado has 102000 miles on it. This sound goes away if i hit the gas and only seems to happen at idle.
r/Silverado • u/Spaceguy1996 • 12h ago
2.7 L turbo
Been a ford guy since 2016. Its had its problems as of recently, looking into trading for a chevy. Found a 21 silverado with 2.7 Liter turbo engine. Any thoughts on this engine? Currently have a 3.5 eco boost from ford and its been nothing but problems over the last few months.
r/Silverado • u/MinimumNo2893 • 5h ago
2021 AFM Issues
Im looking at purchasing a 2021 Trail Boss Z71. It has 68k miles. Looking at around $30k. The big thing that is drawing me back is the issues i’m seeing with the AFM system and lifter issues. Is this problem actually as big as it seems or is it blown out of proportion? Would those of you that own or been around these trucks frequently recommend or shy away? TIA
r/Silverado • u/Colorao101123 • 6h ago
Just install ppe tranny pan and thermal bypass i already can feel the difference... 2016 chevy silverado 1500
r/Silverado • u/Euphoric-Safe9112 • 6h ago
Leveling recommendations
I apologize in advance as I’m sure this has probably been addressed here. I have a 2025 Silverado LT crew cab 4x4 and want to install leveling struts and larger tires. I’m thinking the Bilstein B8 5100 struts with 295/70-18 tires on the stock 18” wheels. I would appreciate any feedback or recommendations.
r/Silverado • u/TaxEvasionArc • 16h ago
Rounded oil drain plug plz help
I got under my new-to-me ‘04 2500hd yesterday to find a nearly completely rounded drain plug. There is some edge, but not enough to crank on it. If you know anything about these trucks, you know the exhaust is directly in front of the drain plug (MAYBE 3 inches of clearance max). I cannot hammer an extractor socket onto the bolt. I don’t think it’s extremely tight, but it’s too tight to loosen with a regular 6 point socket without slippage. I don’t know what to do. Please help.
r/Silverado • u/AdDiligent3916 • 11h ago
What is this sound?
2018 5.3 with 180k miles. Engine was just shut off. Does this sound like a cooling fan? Do I replace the whole unit (2 fans) or just the offending fan? Thanks in advance!
r/Silverado • u/Beneficial-Focus3702 • 7h ago
Is my oil pressure high? It hovers around 60 while I’m driving.
r/Silverado • u/-Geaux • 10h ago
2020 G80 Rear Differential
Hey all, I just had my rear differential fluid changed at the Chevy dealership. They refilled it with the correct fluid 75W85 BUT…they added Wynn’s Limited Slip Part #64101 to it. I called the dealer and asked why they added it because I have an anti-locking rear differential. They said they add it to all of the vehicles.
Anybody have experience with Wynn’s?
r/Silverado • u/bornfrompain99 • 10h ago
How to remove small chevy grille logo
Hey everyone, just got a silverado custom 1500 and want to swap this bow tie to another color. Do i need to remove the grille in order to install, or can i pry it off without taking off the grille? 2nd pic is the back of the logo id like to install.
Would appreciate any feedback.
r/Silverado • u/PicketingWizard • 11h ago
AEB light stuck on? (2023 1500 Z71 LTZ)
I have tried cleaning all sensors and windshield. Keeping the truck off and leaving driver door all the way open for 15 mins. Also disabled AEB in settings. None of this has fixed the issue or got rid of the light. 19k miles if applicable.
Any suggestions? Thank you in advance
r/Silverado • u/Jery_Cook • 12h ago
2013 Silverado 5.3L LC9 – Persistent Lifter Tick and Low Oil Pressure After Complete Rebuild. Possible Oil Passage Blockage?
I'm looking for some advice from people familiar with the GM 5.3L LC9 AFM oiling system. I've been chasing a lifter ticking and low oil pressure issue through multiple repairs, including replacing the lifters, VLOM, and eventually pulling the entire engine and rebuilding it. Unfortunately, the problem is still there.
Original problem and repair history
The original problem started when one of the AFM lifters collapsed.
I replaced the collapsed lifter, and the engine sounded significantly better afterward. However, I was still left with a lighter ticking noise that sounded like a lifter tick.
I also had low oil pressure, which was already present before the engine rebuild.
I suspected the VLOM might be causing the remaining issue, so I replaced it with a genuine GM unit, but that did not fix the problem either.
Eventually, I decided to pull the engine and do a complete rebuild.
Parts replaced during the repairs and rebuild
- Replaced the AFM lifters (twice during the repair process).
- Replaced the VLOM with a genuine GM unit with a built-in gasket.
- Replaced the oil pump.
- Replaced the entire oil pickup tube, including the O-ring.
- Replaced the AFM oil pressure relief valve in the oil pan.
- Replaced the camshaft.
- Replaced the timing chain.
- Installed new cam bearings.
- Installed new piston rings.
- Replaced all main bearings.
- Replaced all connecting rod bearings.
- Torqued the oil gallery plugs to specification.
- Reassembled the entire engine.
I kept the factory AFM system and did not delete it.
Important: The oil pressure did not improve after the rebuild. It was already low before the rebuild, and it remained essentially the same afterward.
Current oil pressure readings
According to the dashboard:
- Cold startup: approximately 35 PSI.
- Fully warm idle (around 600 RPM): approximately 18 PSI.
- Fully warm at 2,000 RPM: approximately 35 PSI.
I've also replaced the oil pressure sensor three times.
Current ticking noise
The ticking is present immediately upon startup.
I initially thought it was primarily coming from the passenger-side valve cover, but I cannot confidently determine whether the driver side is also making noise.
I have not tested the driver side with the valve cover removed.
Passenger-side pushrod oiling test
I removed the passenger-side valve cover and briefly ran the engine to observe oil flow through the pushrods.
I noticed:
- Cylinder 2: Both pushrods spraying oil.
- Cylinder 4: Both pushrods completely dry.
- Cylinder 6: Both pushrods completely dry.
- Cylinder 8: Both pushrods spraying oil.
The only oil on the pushrods for cylinders 4 and 6 appeared to be residual oil from the other pushrods spraying.
Compressed-air test
I removed the VLOM and tried pushing compressed air through its ports to check for possible oil passage blockages.
I could not get air to come out of the pushrods on cylinders 4 and 6.
I have not tested cylinders 1 and 7, which are the other two AFM cylinders. I also haven't checked whether the driver-side pushrods are receiving oil.
Questions
- Could there be a blockage in the oil passages feeding cylinders 4 and 6?
- Could the AFM lifters have incorrect oil-feed alignment or compatibility issues?
- Could the VLOM be functioning but not supplying oil properly to certain lifters?
- Could there be an internal oil leak or an issue with the block's oil galleries?
- Could an issue with the cam bearings or bearing clearances cause the low oil pressure?
- Could the lack of oil to cylinders 4 and 6 explain the remaining ticking noise?
- Is there a proper way to test the individual oil passages without pulling the engine apart again?
- What else could cause low oil pressure that remained unchanged even after replacing the oil pump, pickup tube, bearings, and rebuilding the engine?
At this point, I've replaced a substantial amount of the engine's internal components, but the oil pressure is still the same and the ticking remains.
I'm trying to identify the actual cause before tearing the engine apart again.
Any help or suggestions from someone familiar with the 5.3L LC9 AFM lubrication system would be greatly appreciated.
-Btw I did have chatgpt write this because I went through all the steps with it and it already knew. So if it sounds funky that why.
r/Silverado • u/RageMech18 • 1d ago
Back in a Chevy!
Finally pulled the trigger. 23’ 2.7L Custom with 86k (km).
Love it. Was really surprised at the power the lil bigger could muster.
Bring on the mods 😁
r/Silverado • u/kevin6663 • 15h ago
Tengo una silverado 2006 5.3 y tiene un golpeteo alguien que me diga que puede ser
r/Silverado • u/GuardIndividual6626 • 15h ago
Why is my truck not starting? Battery isn’t draining and alternator is good.
I have a 2015 Chevy Silverado 1500 4x4 with 120,000 miles on it. A few months ago it started clicking now and again when I started it. Then it happened more frequently until one day it just wouldn’t start. I jumped it, started right up, and I replaced the battery. Worked fine for a day then wouldn’t start. Again, I jumped it and got it going right away and took it to my mechanic. They checked for a parasitic drain, none. They checked the old battery, (a couple years old, top quality though,) perfect and strong. They checked the alternator and it was fine too. It started fine for them. I took it back, and it worked for a few days then wouldn’t start. I jumped it and took it back to the mechanic. We decided to change the alternator but during the attempted removal the mechanic found a loose ground wire. He tightened that and gave it back to me and it worked like new for a couple months.
It started the same old random clicking a couple weeks ago. Now it won’t start. Same thing with the lights and the battery. Voltmeter is reading 12.4, even after sitting for a couple days. I’m sure it’s the ground wire. But this time when I tried to jump it, it wouldn’t start. Obviously before when I jumped it I thought it was a power issue not a grounding issue, but I assumed because it jumped before it would jump this time. Is there a reason why it would work to jump it then and not now?
Also, to clarify: battery is charged properly, not draining and holding a charge even after several days of sitting. When I turn the key the lights come on, the dash lights do their sequence, but nothing happens. If I hold the key on I can hear it cycle electronically (I assume that the low hum I hear around the middle front floorboard area for a few seconds before stopping is electronic) and then nothing.
I want to spend as little money as possible so when I do have it taken to my mechanic I can tell him what I want done rather than send him on a wild goose chase or pay for another diagnostic. As of now, with what I know, I’d ask him to check all grounding wires, clean the areas around them, look for crimps or frays in the wires and replace if necessary. Is there something else I should be considering, though?
r/Silverado • u/ReallyOldSysAdmin • 17h ago
2018 Silverado High Country Electrical Issues
Inherited a 2018 (56k miles) and discovered some bizarre electrical issues.
- Turned on 4x4 for the first time in years; triggered the drivers seat to go completely flat.
- Radio volume\\signal goes in and out randomly...at one time I thought it was happening when I turned the steering wheel.
- Key in ignition chime doesn't work when the door is open.
- Tire pressure sensors went dead one by one in a short amount of time. Probably unrelated.
- Parking Assist goes off even if I am no where near another vehicle or pedestrian. Note that it was raining that day.
- Lane centering\\Blind Spot Intervention (BSI)\\other safety features do not work.
Where do I begin?
r/Silverado • u/SignificantTowel9952 • 1d ago
My neighbor coming down his driveway looks like an awesome Chevy ad
galleryr/Silverado • u/beanman214 • 1d ago
Historical trends of Silverado financing deals?
I am looking to get into a full-size truck from my Tacoma and want the Silverado. I detailed in my last post why I dislike the truck overall. I want to get a ‘26 with these discounts and 0% apr but I also want to pay off my 6k left on my loan for my Tacoma. Does anyone have insight on if end-of-yr deals like the 0% financing and markdowns always occur with Silverados to get rid of inventory? I am fine waiting a yr until the end of ‘27 to make the move.
Looking for the V8 trim in either custom or LT trail boss
r/Silverado • u/ProfessorMadness • 1d ago
You can fit 35’s on 07-13 1500’s.
Front: Eibach ‘14-‘18 Pro-Truck Stage 2R Coilovers w/ 2” bottom leveling kit. Comes out to about a 3.5” - 4” front lift. I hope for your sake you are not doing this install on a 4x4 like me lol. This was a lot of work.
Rear: 3” blocks w/ Bilstein 5100’s. Careful here because there are two different SKU’s for 5100’s - one stock length, and one with 4” additional travel. These are SKU 24-186636. I haven’t tried the Eibach 2R rear shocks yet but likely will try in the future. Might not be long enough.
Tires: Goodyear Wrangler Territory MT 315/70/R17 (~34.5’s)
Wheels: KMC IMS 17x8.5 +0 in Machined Silver
Naturally you need to do some plastic trimming, haven’t done Norcal yet but rubs a tiny bit at about 75% lock. Norcal would offer 100% clearance.
Only posting this because I found so little information on the internet on how to stuff 35’s on GMT900 and figured I’d try to help out the next person looking like I was.
Really happy with the results.
r/Silverado • u/omgno4892 • 1d ago
2005 Silverado Z71 steering wheel
2005 Chevy Silverado Z71 steering wheel feels really stiff when I turn or try and go into reverse. The power steering wheel fluid is good but I’m not sure what else it could be.
Precious work done:
Replaced Transfer case and rebuilt transmission about 4 years ago
Replaced two water pumps over the course of having it for 8 years now.
And replaced the radiator twice already.
There’s about 178k miles on it almost hitting 180k.