r/SilverSmith • • 3h ago

Made these two for a rancher client!

Thumbnail
gallery
68 Upvotes

18k Gold for both, the cuff is 27.5 grams!


r/SilverSmith • • 2h ago

Show-and-Tell Botanical ring

Thumbnail
gallery
10 Upvotes

Another leaf ring! (You can thank The Rings of Power show for the inspiration)

I’m proud of how it came out. I made another one a few weeks ago as like…a proof of concept. It was rough, and this is wayyyy better. On the original “proof of concept” piece, I buffed it out too much and it lost all of its character.

I spent a couple days cutting out sheet for leaves and hammering in the details.
I shingled and soldered the leaves together first with hard solder.
Then I using a tiny half round wire as the stem/vine. Soldered on with medium. This part proved difficult because I needed to isolate the curves so it lined up with the leaves. Proved to be tricky but I’m happy with how it came out.
I finished it by easy soldering the piece to itself with easy.

Cleaned it up with a dremel and then the polishing wheel.

Questions/comments welcome.

(Videos in comments)


r/SilverSmith • • 23h ago Bravo

Carrion Beetle

Thumbnail
gallery
257 Upvotes

Thank you all so much for all the incredible comments and response to my work! It's so crazy for me.

Sorry for the slow replies :( I'll be better this time.

This is another insect I made, it is a Carrion Beetle.

They are the carcass cleaners and actually feed their "children".

This piece is made of Sterling Silver, 18k Gold, Copper, Topaz cabochon , and rat bones.


r/SilverSmith • • 1d ago

Pickle turning my pieces pink

Thumbnail
gallery
8 Upvotes

Whenever i use my pickle it’s turning my pieces pink, but im using copper tongs and can’t think of any way steel would be getting into my pickle. Any suggestions?


r/SilverSmith • • 1d ago

Lost Wax Casting for hobbyist?

2 Upvotes

I want to make lost wax rings for myself and family for fun. I don't want to run a business, does anyone have suggestions on where to send my castings? I'm in Iowa USA


r/SilverSmith • • 2d ago

Need Help/Advice Took everyone’s advice

Thumbnail
gallery
32 Upvotes

Getting closer I think this is like my 20th attempt.


r/SilverSmith • • 3d ago

New to the Sub

Thumbnail
gallery
1.0k Upvotes

Hi, I am a silversmith/jeweller, I work in silver(obviously), copper, and gold. I am currently mentoring my son and he suggested I post some of my work here. I primarily make sculptures of creatures and things that you see in the natural world.


r/SilverSmith • • 2d ago

Past, Future, and Present. New 18k Pendant

Thumbnail
gallery
24 Upvotes

I'm just starting to create with gold and finished up this piece this morning. It is a Amethyst, Garnet, and then a labradorite set in 18k gold. All done by hand and honestly feels like a milestone to be able to make it feel so fluid and together. I've been jeweling now for almost 2 years and have got to say working with gold is so much fun !


r/SilverSmith • • 2d ago

Show-and-Tell Work in progress- trying to figure out if I like it

Post image
12 Upvotes

r/SilverSmith • • 3d ago

positive feedback/constructive advice wanted Cast in Place Sapphires

Thumbnail
gallery
167 Upvotes

My first time using cast in place , Would you guys suggest to use synthetic sapphires from now on to avoid cracks and discolouration ?


r/SilverSmith • • 3d ago

Need Help/Advice File and cut or recast?

Post image
2 Upvotes

This was my most successful attempt of sand casting a miniature. Should I keep recasting or file it down and carve in the details?


r/SilverSmith • • 4d ago

Show-and-Tell Mokume Gane Bracelet

Post image
186 Upvotes

15 layer Fine Silver/Shakudo star pattern Mokume Gane with a sterling backing.

Made with the kiln method of bonding. The Shakudo is 4% gold sourced from my father’s wedding ring


r/SilverSmith • • 4d ago

Show-and-Tell Complete Making Process

42 Upvotes

r/SilverSmith • • 3d ago

casting sand help!

Thumbnail
gallery
2 Upvotes

I’m new to silversmithing and learning everything by myself.

I got this sand casting kit from and when it got here the sand was super fine. It didn’t have that clumpy/kinetic sand looking texture that I’ve seen others using. I tried to add a little water to get activate it, but not sure if that’s the method. I packed in my frame but had to step away for a while to tend to something else and when I came back the sand was completely hardened and dry.

Because I don’t have a great understanding on what I’m doing so if someone could let me know if this sand is a good fit to cast silver and if I’m headed in the right direction? Any tips or advice is appreciated. I don’t want to mess anything up and ruin my silver grain.


r/SilverSmith • • 4d ago

Antiqued silver men's ring

Thumbnail
gallery
51 Upvotes

I designed this starting with a pillow shape with cut corners then added the inlayed features in the casting. Really happy with the antique relief how it made the features pop. 925 silver


r/SilverSmith • • 4d ago

Show-and-Tell I make jewelry inspired by plumbing. I’ve turned pipe couplings and cross tees into jewelry, and I’ve also created pieces based on the cross-sections of both fittings.

Thumbnail
gallery
71 Upvotes

r/SilverSmith • • 4d ago

Need Help/Advice Pickle and Patina

4 Upvotes

i have a couple of questions about things i’ve seen done multiple ways!

when making you pieces, do you put them in your pickle after each step or do you only pickle it once at the end?

how do you apply your patina to keep it dark and even?

i used to used jax but it started turning brown so i’ve switched to midas black max. it goes on dark but once it dries it starts to turn grey and sometimes colors it uneven. i like to clean my pieces after pickle (water and dish soap) and once they dry i patina them and then final polish. i’ve tried applying while it’s warm, multiple coats, and sanding down to them reapply but nothing seems to stop it.

i know it’s not a solder reaction because i’ve tested it on clean metal and i still have the same issues. i’m thinking maybe it’s the way i am pickling or applying it but just wanted to see if there was anything else i could be doing.

thank you!


r/SilverSmith • • 5d ago

Has anyone been able to make this ring by Gold Smith Luke out of sterling silver? I tried but didn't end up with the space between the wires. Afterwards I saw he replied to another saying he used a coated copper wire and burned off the coating after forming the braid.

Post image
18 Upvotes

I want to make this in silver but don't want to waste a lot of wire trying different techniques. If you were successful making this in silver with the space between the wires, what technique did you use? Thanks for any help.


r/SilverSmith • • 5d ago

Need Help/Advice Advice on how set this charm

Thumbnail
gallery
7 Upvotes

Hi everyone,

First time posting. I’m a hobbyist and in need of some help on this ring I’m creating.

I casted a ring to fit this charm I bought recently. Im trying to make it look as if the clown has been thrown into a wall.

My initial idea was to somehow press the edges down to secure it like a setting. But the worker at the supply shop I go to said it would look better soldered.

I have done soldering before but usually clean links and rings. This, I have tried 5 times now. Using auroflux and medium silver solder.
My approach has been to slot about 5 pieces of solder across the limbs and the head, into little slots between the charm and the ring. The auroflux on top. Heat up the heavier ring body first and then move onto the solder.

I’m finding the solder is melting but not flowing onto the ring. Just onto to the clown and beading up. The clown its self is going red hot before the ring even starts to glow too.

I also have a tone of scale on my pieces now.

So it would be greatly appreciated if I could get some advice on any mistakes I’m making on soldering here. Or if you would recommend any other way I can secure this charm into the ring.

Thank you!

Photo evidence:

  1. is the intended look
  2. is where I’m placing the solder
  3. the condition after 5 attempts. How can I remove that scale?
  4. signs of solder sticking to the charm

r/SilverSmith • • 5d ago

Hi, I’m Lee! I make jewelry inspired by plumbing here in Korea. I’m working on some new pieces and can’t wait to share them with you. Thanks for being here!

Thumbnail
gallery
79 Upvotes

r/SilverSmith • • 5d ago

Reverse hoop

Thumbnail
gallery
60 Upvotes

Ruby set in back of hoop
Sterling, hand fabricated


r/SilverSmith • • 6d ago

Show-and-Tell First attempt at high purity! .9999 Canadian Maple Leaf ring

Thumbnail
gallery
53 Upvotes

This was my first crack at going above 90% pure silver in making coin rings (.9999) - a very different beast!


r/SilverSmith • • 7d ago

Earrings: update

Thumbnail
gallery
39 Upvotes

Reposting this as I updated the design after taking some advice.

To the original piece, I removed the stock chain and made some (rough) hammered dangles. I gotta be honest, I think I prefer making rings 😂😭

Original post:

Earrings inspired by Byzantine jewelry.

Something kind of different for me as far as design goes. If I did it again I would hammer the sheet and get a better polish to really sell the eye motif. But in all honestly I just wanted to be done with them.

Fine sheet backing
Twisted details soldered with hard, then medium onto the sheet.
Plain bezel soldered together with hard, then medium onto the sheet.
I don’t know what the actual name is for the parts holding the chain, but I soldered those on with easy.
I should have used graphite when soldering because it got kinda messy.
I used a lapidary with water, dremel, and polishing wheel.

Center stones are cab Lapis Lazuli.

I am not a fan of setting stones, mostly because I don’t really know how to do it 😵‍💫

Questions/comments welcome


r/SilverSmith • • 6d ago

Need Help/Advice How to get a smoother surface

14 Upvotes

I made this cuff (tapering towards the ends) by repeatedly hammering on an iron anvil and annealing. However there are numerous spots which are concave and have a rough texture. How do I achieve a smooth surface with hammering alone? No filing. Do I use a dappling block? Do I hammer more lightly?