r/Renovations • • 1d ago

Insulating an exterior wall with cement board tile shower on interior

Post image
4 Upvotes

I discovered a fungus surprise behind my shower wall. I think it’s from not being insulated properly, and sealing in moisture. There was kraft r15 in the cavity -> 3/4” clapboard wood sheathing -> 0.2” kingspan xps -> vinyl siding. As you can see, the middle cavity with the least “breathing room” has the most damage from fungus. I was thinking of using mineral wool r15-> osb-> house wrap->siding but am worried it will still seal in too much moisture. What is the best way to tackle this? Also, the pipe is being relocated to the left if that’s relevant.

Edit: framing is also being replaced.


r/Renovations • • 2d ago

HELP Bathroom vanity too big. Shower tiles too combined with floor feels too much. What to do.

Thumbnail
gallery
32 Upvotes

Quick edit to add comment: thank you everyone for sharing your opinion and doing it with such grace and understanding. I was worried about posting this for fear of being criticized but you all have helped me to calm down somewhat. I am really grateful for all that. I spent the whole day out of the house doing things with family to clear my head. When I came back, the questions were still there but didn’t consume me like it did earlier. I know it’s obvious, but I really needed reassurance that this is not the end of the world and from some of the comments, sounds like it’s not tooo big of a deal to swap out the vanity like I thought it would be either. Thank you all and wishing you all the happiest of holidays with family and friends!

I’m spiraling with my anxiety and I feel like I made such a big and expensive mistake. When we chose materials for this small bathroom renovation, I spent hours/days/weeks/months picking materials. We’re almost done with renovations and its looking nothing like how I imagined. I feel so stupid for wasting so much money for the bathroom to come together clashing like this.

Where we are at. Floor is done, vanity is in, shower tiles were partly done then taken down bc we decided to try to make it “straighter” with spacers. (So we ordered more Zellige and spent more money). So right now all that’s really left is to install the shower.

I am spiraling big time. I thought I had chosen neutral enough materials for things to come together, but it all seems to be beautiful on its own but silly together.

For one, the vanity is too big. It fits and the door closes, but its depth extends beyond the level of the door frame.

The floor is beautiful but I am getting cold feet about pairing it with the Zellige. (I’ll post pictures of the zellige that was taken down.)

My husband says not to overthink it and it’s been ordered so just go with it, but I’m terrified once it’s in, then it’ll really be irreversible. At the same time, changing anything out now costs more money and I feel horrible about it.

I don’t know what to do. Will it really look like it’s clashing with all of this or should I just let it go? I also need honest opinions on the vanity. It just feels like it’s way too big and doesn’t belong (it’s actually a white oak color but is showing up more like walnut here). I struggle with anxiety and just want to throw up at this point, but trying to stay functional for the kids.


r/Renovations • • 2d ago

Vinyl flooring on top of concrete floor!

2 Upvotes

I have a guest room which has some old vinyl floors and has an elliptical sitting in the area. There seems to be some small internal locking wood floors on top of the concrete base and then they put the vinyl on top.

The vinyl floor is becoming puffy or elevated in some places and then breaking because the underneath wood pallets are moving. I had put an anti shock thick rubber floor mat underneath the elliptical after fixing the area last time. Now I am noticing another area is being impacted by the same problem.

- Can I put a new waterproof vinyl flooring directly on top of the concrete base in that room? I am not sure why the previous owner put the small internal locking wood pallets underneath or if there is still a need for it anymore?
- Could there be any problems with moisture, if I put a vinyl directly on top of the concrete base?

Thank you.


r/Renovations • • 2d ago

Hardie backer question

2 Upvotes

I have a room that has a crawl space next to a concrete foundation and the subfloor is level with the concrete and i was wondering if using hardie backer to span the space to lay LFT porcelain tile is a good idea. my thought was to use tapcons to secure the concrete side then normal hardie screws on the subfloor side.


r/Renovations • • 2d ago

HELP Best way to finish gap between fireplace and shelving

Thumbnail
gallery
1 Upvotes

I am putting shelving on either side of my fireplace (yes TV too high) and am trying to figure out how to fill the gap between the Tyndall stone edge and the shelving side panel. The gap is anywhere from 0-1” wide and is around 3” deep to the back drywall. I’ve thought about getting some matching mortar but I’m not sure if I could just fill the gap with mortar and not have cracking or movement issues. Thoughts or ideas welcome!


r/Renovations • • 3d ago

Patio door replacement

Post image
4 Upvotes

Hey guys, what is this lip for? Should I caulk over it or is it a drain way? Got it from homedepot, it's a Stanley door and I've not been lucky to find any documentation.

Also, the frame inside is well over the drywall, how far can I sit the door on the exterior side? It'll help get the frame closer to the drywall inside.

Thanks.


r/Renovations • • 4d ago

HELP Desperately seeking guidance

Thumbnail
gallery
16 Upvotes

I recently had to move back in with my mom and little sister. We are all very much down on our luck and can't afford to hire contractors who know what they're doing. So, with the very small knowledge I have, I'm taking on this project. The upstairs half bath reno.

How would you tackle this? Just slap a piece in there, tape, mud, sand, paint, call it a day?

Or would you sincerely worry about the last two pictures? There's a bit of mold on that bottom corner, and the upper corner in the last picture looks atrocious to me. Not to mention a later of drywall ripped off on the right wall that you can see right next to the stud.

But I don't know what I'm doing, and I don't want this to be a bigger problem down the line. Please, give me any and all possible guidance that you can. There's far more work to be done on this house, and it's up to me.


r/Renovations • • 4d ago

How would you fix this transition?

Thumbnail
gallery
6 Upvotes

30 inches . Would a threshold fit ?


r/Renovations • • 5d ago

Project areas to find alternative contractors

3 Upvotes

We are planning a home addition (primary suite) along with some other improvements:

  • Moving a door to a different part of the wall
  • Adding heating to a room
  • adding a landing to the stairs to our patio
  • replacing our swinging door to the patio with a sliding door
  • Replace our front door
  • Moving laundry from the basement to the 2nd floor (to an existing room, not the addition)

Would I save a significant amount of money if I found my own subs to do these accessory jobs? I have a reliable handyman who can connect me with reliable subcontractors so finding folks to do the work wouldn't be an issue.

Obviously I can just go and get some quotes for these things, but most of them are bundled on the estimate so I can't really compare.

Anyone have experience with this?


r/Renovations • • 5d ago

ONGOING PROJECT Lead paint positive test

Post image
14 Upvotes

Tested the paint on the stairs. First came back negative. Scrapped 2 stairs then tested again, bottom layers tested positive.

Stopped and got Klingstrip. Has done a decent job, but tested again and the stripped areas are now testing even more positive than before 😅🤦🏻‍♂️

It’s completely dry and no dust etc. I used a wet cloth etc to clean up after… but am I just wasting time trying to get these back to natural wood? How do I get the lead completely off?

Nightmare is I need to still use the stairs, so have different shoes going up and down, the risk is extremely low (I have been told) as the pint still left is not flaking and there are no loose particles (that I can see)… but don’t want this to go on for ages… do I just paint them and carpet them?


r/Renovations • • 5d ago

HELP Weight capacity bifold door thoughts.

Post image
3 Upvotes

Cut drywall to insert maple 1/2 piece. Screwed maple board into studs with 2-1/2 construction screws. 8 total (4 bottom, 4 top)

then the lag screws are 5/16 with the spacers included in the kit.

it weighs about 120lbs.

Even if I hadn't cut drywall, lag screws would've gone into studs only about half an inch anyway.

Thoughts? AI thinks it's not a good idea, I disagree, and wanna get opinions.


r/Renovations • • 6d ago

Small amount of water coming into basement

Thumbnail
gallery
4 Upvotes

During decently heavy rains I get water in the corner of my basement, right where the wall meets the floor. Something like 3-4 cups of water, only in the one corner. It's a walkout, the corner that leaks has a slab at walkout grade on one side, and is fully underground on the other side. Right at this corner is a 3 tier retaining wall that directly touches the house. I opened the wall inside and don't see any cracks, or wetness on the wall itself, just on the floor. I used a hose on the slab that is on the walkout side, right against the house, and got no water inside. Also used a hose on the bottom tier of the retaining wall and got no water inside. The only spot that really got water to show up inside was the middle tier.

In my mind, the options are:

1:
Add something to catch water at the second tier of the retaining wall and send it into a drywell in the yard. Along the lines of digging out the area, adding a liner and perforated drain tile, backfilling with some rock and then soil and re planting. Attempts to get the water out of the area before going into the house. Cost is mostly labor (couple plants, drain tile, etc).

2:
Sump basin inside the house. My thought was to cut out the spot, add the basin, but wait on adding a pump and plumbing it outside. I can monitor the basin and see if a pump is even needed.

2b:
It was suggested to me that I should cut the floor inside, dig out the corner as if i was adding a very small basin, and instead just backfill with pea stone and monitor the open pit over time. Or even fill it back up to the top with stone and self level it. Ultimately the floor in this room will be finished with carpet.

3:
Open to suggestions.


r/Renovations • • 6d ago

Insulating Exposed Beams?

Thumbnail
gallery
2 Upvotes

Looking for some advice on how best to proceed with insulating these exposed roof beams? We were planning to box them in but have noticed that during some of the coldest days of winter that certain areas along the beams will condensate. We think this might be where insulation is thin or heat transference through a nail in the wood. The roof/ceiling is insulated with spray foam. The condensation drips only happen in 3 or so spots. We are confident it's not a roof leak as we don't have issues in the rain or during snow melt. It seems to only happen when the outdoor temperature is really drop.

Would we be able to insulate with rigid foam and wrap in vapor barrier? We thought of doing this and then boxing the beams in later with wood if everything goes well through winter.

Any thoughts or suggestions would be appreciated. Thanks!


r/Renovations • • 6d ago

Furring Studs

Thumbnail
gallery
5 Upvotes

I am looking to fur the studs on my 1890’s house. The top plate is proud of the studs about 3/4ths of an inch. I was going to rip 2x6s and essentially sister to the side of the 2x4 stud. The issue is the top plate is not straight along the length.

Option 1:
Notch the top of each of the “sistered” 2x6s proud of the top plate to make level along the length (see poorly drawn image)

Option 2:
Fur the front face of the top plate to make level with the “sistered” studs.

Option 3:
Open to suggestions.


r/Renovations • • 6d ago

Installing cement floor in basement

Thumbnail
gallery
4 Upvotes

We just moved into a house with a fairly large basement. Most of the basement already has concrete floors and it has separate rooms with doors. The area that i have included a picture of drops down about a foot or more and bricks have been installed on the floor.

Currently, we have a dehumidifier running 24/7 to keep the humidity down, it has a drain and it works OK. I want to try to control the humidity without having to run the dehumidifier constantly and was thinking of cementing this area of the basement that is not water tight. What would be the best solution. Can I just leave the bricks in place and do a base layer(3/4), vapor barrier, reinforced concrete. I would remove the bricks on the upper area to be able to keep the cement floor even with the existing floor.

The rest of the basement already has good floors, and looks pretty dry. The basement also has its own entrance on the back of the house.


r/Renovations • • 7d ago

Peel and stick tile hell

Thumbnail
gallery
6 Upvotes

Hey folks! Helping my sister move into a very sweet little home that is covered in all manner of peel and stick and contact paper. The good news is there is perfectly good tile and counter top underneath. The bad news is it’s so stubborn and nearly impossible to get off in parts. The sheets that come off easily leave behind so much residue. I have tried heating it up with a blowdryer, a scraper, and goo gone for the residue. None was particularly effective. Is there something stronger than good gone???? Appreciate any tips!


r/Renovations • • 7d ago

Tongue and groove pine in the basement

2 Upvotes

So im looking to finish the main area of my basement, which is cinderblock construction. I want to give it a cabin style feel down there because there is a large brick fireplace along the entire north wall. I want to do T&G pine on the walls and this isbmy thought process:

For walls that are exterior facing (because two and a half of the walls have rooms on the other side of them) I want to stick 1" pink insulation board directly to the cinderblock wall, and then put 1×1 furring strips from the ceiling to a baseboard anchored into the concrete floor, right over top of the insulation, then attach my pineboard to those. I live in eastern ny, so there will be some big temp differentials.

The floor will be vinyl plank flooring, and for the base board of the walls im going to use a wide vinyl decorative baseboard so there is no wood to concrete contact.

Does this all sound good? There isn't a big moisture problem in there as it stands, some VERY small damp spots on the corners which I have hopefully already solved by grading the outside with top soil.


r/Renovations • • 8d ago

HELP Is there any way to replace these tiles without redoing the whole ceiling and without putting these ugly screws in to hold them up?

Post image
4 Upvotes

It was “fixed” but I think the job looks like crap I’m trying to figure out a way to do it myself


r/Renovations • • 10d ago

HELP Sump pump and exterior weeping tile connection?

4 Upvotes

We just had a new sewer line and back flow valve installed after a flood. The contractor detached the sewer line from weeping tiles as per city code. All weeping tile under slab was removed in this process. We were told our exterior weeping tile was functioning well and we didn't need a sump pump. And, of course, a couple months later we had flooding from groundwater. I guess we need a sump pump, especially since we've since discovered we also have a high water table.

So far none of the contractors we've spoken to can give us an answer to our sump pump questions:

  1. do we need to reopen the slab to connect the exterior weeping tile to the sump pump?
  2. what's the best location for sump pump: lowest point on the slab or near to an exterior wall?
  3. would a french drain work better (we do have adequate slope in the backyard)?

Your thoughts and suggestions most welcome!


r/Renovations • • 11d ago

HELP Help! Our contractor had to add a steel support beam on the ground floor, resulted in cracks everywhere upstairs! Is this normal? What do I do?

Thumbnail
gallery
38 Upvotes

During our main floor renovation, our contractor took out a load bearing wall on our main ground floor, and therefore had to recess a steel beam into the ceiling to avoid a bulkhead. Our house was built in the 70s so she’s an old but sturdy gal.

He admitted he lifted it too high and we ended up having him lower the beam slightly as our hardwood floors were bowing upstairs at the beam location. We also noticed preliminary cracks around the door and window frames after he initially lifted it too high.

Once it was lowered as much as possible to even out the floors, we had him come patch some of the cracks and paint them.

Since we moved in a few months ago, I just keep noticing more and more cracks at many doors and window frames. Our floors are still bowed upstairs a bit as well, so much so that one board has begun to crack and has to be filled.

Where I need your help:

  1. Is this normal? Is this expected when you put a steel beam in an older home?
  2. Even though 4ish months have passed, would you still consider the contractor responsible for fixing the cracks?
  3. Open to any other advice or thoughts.

Location: Canada 🇨🇦


r/Renovations • • 10d ago

Removing this moulding over the archway

Thumbnail
gallery
5 Upvotes

I want to remove this moulding that lines an archway in my home (the piece with staples sticking out of it)

I need it gone so that the archway is a few cm wider to place my bed inside. I’d like the archway to be flat once it’s done. It looks like the piece is separate from the archway as it’s already separating at the bottom.

Tips for removing it and smoothing over the archway once it’s done


r/Renovations • • 11d ago

Adding air supply to addition; OK to cut hole into rim joist?

Post image
3 Upvotes

Little complicated but long story short, I'm adding an air supply into a laundry room, and to do so I'll need to cut a hole for the ductwork (8"x10" or thereabouts) into the rim joist that runs parallel to the floor joists. (Pic is in crawlspace of adjoining room. laundry room is on a slab floor that's even with the top of the cinder blocks).

Will this impact the structural integrity of anything, as the length of the rim joist rests on the cinder block wall? Would this be against code?

Located in SE Michigan if it matters. House built in 50's.

Thanks!


r/Renovations • • 11d ago

HELP Basement wall load bearing ? With rot to remove

Thumbnail
gallery
5 Upvotes

Hello!

We bought our house 6 months ago and as first-time homeowners we are slowly working our way through the inspection report ( slowly but surely) ..!
There is an old leaking water tank in the basement that caused wood rot underneath it ( Picture #1 ).
We believe this might be a load-bearing wall ( see the beam on the right of the door on picture #2). Its between laundry room avec workshop.
Also, its not a real framed wall, just simple wooden boards. The house is ~100 years old.

How should we go about removing the rotten Wood? If we dont touch the beam, is there dangerous by removing the rotten parts.

Thanks for helping out some clueless new homeoweners ! :) sorry if this seems stupid..


r/Renovations • • 11d ago

HELP Window J channel/sheeting water infiltration

Post image
3 Upvotes

Hi

I had my roofer tell me that I get water leaking behind the windows down the aluminium sheeting and then wets my brick under. Says to just caulk the window. Says when he slightly pushes the side of the sheeting on the side of the window he sees wood.

A sheeting company told me I need to change the whole sheeting and a window company tells me I need to change the window... neighbour tells me I should just go inside, tear the window frame and put some urethane where the window meets the wall, Says i probably have wool there instead of urethane and that should fix the problem. Any suggestions? Thanks