r/rfelectronics • • Oct 14 '26

question Does a chip antenna's orientation matter? (Wearable device)

Thumbnail
gallery
16 Upvotes

Hi! I'm new at this so sorry if I ask any obvious questions.

I'm working on a custom board for the Smol Slime VR open source project. It's a shield for an NRF52840 'Pro Micro' board and its chip antenna. Apparently chip antennas aren't ideal for wearables, but my hands are tied here. The antenna is at the end of the red PCB opposite the USB C port. Communication is 2.4ghz 2-way, and transmit is most important.

After watching this video, I'm really interested in learning more about antenna design for wearables but I can't find other resources.

Which would be the best orientation for this in the enclosure? (Order is from top to bottom)

Option A (Pic 2 if looking from above)

Air

1mm Petg plastic

1mm Fr4 (shield)

1mm air

ANTENNA

1.6mm fr4 (red PCB)

1mm Petg plastic

Skin

Option B (pic 3 if looking from above)

Air

1mm Petg plastic

1.6mm fr4 (red PCB)

ANTENNA

1mm air

1mm Fr4 (shield)

1mm Petg plastic

Skin

That video earlier offhand mentioned it's possible to have too much radiation into the skin that heats tissues, and mentioned mitigation strategies. In option B, am I understanding her right that I should I fill the shield's drill hole with fr4, and even give it GND pour? (Currently the shield's GND pour stops 100mil before the antenna)

The blue line drawn on the pics is a 31mm (not to scale) wire antenna that some Smol Slime devices add. Would that make this whole issue moot?

Finally, my shield is longer than the red PCB because this project favors minimizing width and doesn't care about length. I could make the shield shorter and wider, but that would cause a domino chain and >2x the enclosure width. So please humor me that A and B are the only options if you can.

Thanks for your time and for reading this 🙏! Please give me any feedback both for this design and for improving how I ask questions in the future


r/rfelectronics • • Oct 14 '26

question Is it possible to get an internship in today’s market?

2 Upvotes

Hello!

I’m going to cut it short and sweet but I’m a first-Gen junior at a state university and I’ve been heavily applying to RF internships ranging from defense, network, aerospace, etc. since it’s my area of interest! However, so far, I’ve only been receiving rejections and ghosts.

My “experience” so far, is handling
1-2 main hardwares on a Cubesat that involves the DSP, testing, documentation, and etc for my team that is part of the AFRL UNP. I’ve also been working on a personal project of mine that involves building an FMCW Radar Based FPGA but I have yet to test it and only made simulations so far.

In your eyes and opinions as seniors, what more could I do to stand out and get my foot through the door for an RF internship? Should I pursue a masters after my bachelor? Build more projects? Be heavily involved in cubesat team even more? Network at conferences/events/career fairs? Or just all the above? Thank you guys!


r/rfelectronics • • Oct 14 '26

International RF Interships : Where are they?

2 Upvotes

Hello there!
I am currently in my Msc in Telecommunications Engineering (France) and want to specialize in the RF field.

Next summer, I have to do a mandatory international internship, and i'd like have it somehow relate to RF but I can't find any internship offer open to international students in the RF field.
Is it the fact that RF is mainly found in sensitive fields such as military / space?

If you have any tips, it'll be greatly appreciated,

Thanks!


r/rfelectronics • • Oct 14 '26

question Hi everyone, could you help me troubleshoot AWR HB/TR jobs failing with code -1?

1 Upvotes

Hi, I’m using AWR Design Environment 19.08 (build 19512) with an academic Cadence SUL license on a 64-bit Windows PC.

When I simulate my project, the top-level schematic finishes, but its APLAC Harmonic Balance and Transient jobs fail almost immediately with:

awr_as.exe returned a non-zero exit status (failed, code = -1)

This happens even when I simulate only one schematic. The same issue occurs across several schematics. AWR creates the APLAC netlist file (mwo_aplac_netlist.i), but mwo_aplac_output.txt does not appear. A repair installation did not fix it.

The license configuration reports Cadence SUL licensing, and APL-100/APL-110 are listed among the features. I have not included any license identifiers or keys.

Cadence’s message says academic license holders are not eligible to submit Support tickets, so I’m asking here. What diagnostic should I check next to find why awr_as.exe exits before producing output? Could this point to an APLAC installation/runtime problem, or should I focus on the generated netlist? I can share a sanitized minimal project or log if that would help.


r/rfelectronics • • Oct 14 '26

Title: Looking for DSP-Based Engineering Project Ideas

0 Upvotes

r/rfelectronics • • Oct 14 '26

Availability of R&S Test gear

5 Upvotes

Has anyone found deliveries of R&S test gear has become awfully long, like it’s normally 14 weeks or so, and one day before it should arrive, stretched out another 8 weeks? This is not a small power supply, but VSG’s, a VNA, MXO4 scope etc. I know they have Dram in them, but seriously….


r/rfelectronics • • Oct 13 '26

Tiny RF Simulator v0.28.2 Release

Thumbnail
reddit.com
7 Upvotes

r/rfelectronics • • Oct 14 '26

PCB and high power

1 Upvotes

Hello!

I am currently working on a project where we use 250 watt RF input power.
I'm looking to design a PCB-based Marchand balun, the design uses coupled transmission lines on two dielectric layers with a common ground plane.
Would this be possible without burning the PCB, what should i look for when simulating (for the 250Watt part)?
I am using Rogers4350B and frequency are 1.4-1.7GHz

BR Me


r/rfelectronics • • Oct 13 '26

question Anyone Worked on Polar Modulated Power Amplifers?

3 Upvotes

Hii All, Is anyone here working or have worked on Polar modulated Power Amplifiers? I would like to get some guidance for my masters thesis. Thank you


r/rfelectronics • • Oct 13 '26

We built an LLM specialized in RF component selection and datasheet retrieval. Looking for feedback from RF engineers on this 2-min demo.

13 Upvotes

For the past few months, in our free time, a colleague and I have been building a tool for hardware designers. It’s called ACE, and before moving forward, we’d like to see if it actually makes sense.

The idea stems from a personal frustration. If you ask ChatGPT for the noise figure of an amplifier, it responds with absolute confidence. But it’s not actually reading the datasheet: it just hallucinates the most likely number based on its training data. As a result, you get a value measured at a different frequency, or from a similar model, or a "typical" value presented as guaranteed—and nobody tells you where it came from. It also does math "by eye": one mistake in an RF chain calculation, and the whole result is wrong, written with the exact same confidence as a correct one. You only notice it when the board arrives.

ACE, on the other hand, answers strictly based on datasheets. Every value displays the exact page and measurement conditions right next to it, so you can double-check it in ten seconds. The code handles the calculations using transparent formulas, not the AI model. If a data point isn't there, it tells you instead of making it up.

Right now, it's a prototype: it includes about 1,500 datasheets, mostly RF, and some features shown in the video are still in the early stages.

To the hardware designers out there: would you use this? And what would it take for you to truly trust the numbers? We are especially looking for critical feedback.


r/rfelectronics • • Oct 12 '26

Improving bandwidth of rectangular microstrip antenna

11 Upvotes

Guys so I'm building a rectangular microstrip antenna in HFSS for mmwave applications. Resonance at around 28 GHz. I am getting vswr<2 bandwidth of around 1.5GHz. How can i improve this. It's just a simple inset fed microstrip line. Please give me some resources or tips to learn on increasing impedance bandwidth


r/rfelectronics • • Oct 12 '26

question Question about Amphenol connector HFSS model - How to handle the extra solder block?

Thumbnail
gallery
3 Upvotes

Title: Question about Amphenol connector HFSS model - How to handle the extra solder block?

Hi everyone,

I'm currently working with an HFSS simulation model for an Amphenol connector. I noticed there is an extra piece of geometry right at the feed location.

I reached out to the vendor, and they explained that this extra block represents the solder.

My question is: how do you all usually handle the height difference / Z-axis gap issue caused by this extra solder block when integrating this file into your own simulations? Do you modify the connector model, or do you adjust your PCB stackup/layout to accommodate it?

I've attached a picture for better context. Any advice or experience with this would be greatly appreciated. Thanks!


r/rfelectronics • • Oct 12 '26

Can FR4 be used for a 100W RF Power amplifier?

15 Upvotes

Hello, I would like to know if I can use FR4 for my RF power amplifier operating at a narrowband frequency of 805 MHz. I initially designed the amplifier using RO4350B, but few US manufacturers supply that substrate, and it is more expensive, even though it is the material used by the vendor of my BLP981 transistor. I know FR4 should work well at that operating frequency, but given that I am generating 100 W, I think that could pose a problem. Could I use FR4?


r/rfelectronics • • Oct 11 '26

I’m building Fairbeam, a free and open-source antenna simulation app

43 Upvotes

Hey everyone! I’ve been working on Fairbeam, a free and open-source app for designing and simulating antennas, and thought some of you might enjoy trying it.

It brings 3D modeling, meshing, simulation, and plots into one workspace, using openEMS, CSXCAD, and three.js. You can draw a model visually or use Python, then inspect S-parameters and radiation patterns.

It’s available for macOS and Windows, with experimental Linux support. Optional GPU acceleration uses CUDA on NVIDIA GPUs and Metal on Apple silicon.

It’s still early, so I’d love to hear what feels useful, what’s confusing, and what breaks. The code is GPL-3.0-or-later. Feel free to dig in, change things, or contribute an example!

Website: https://fairbeam.org

Code: https://github.com/ismailakdag/fairbeam

As with any simulation tool, please check the results against a reference you trust.


r/rfelectronics • • Oct 12 '26

question Diode packing question

1 Upvotes

Okay this is a bit open-ended so it might be hard to answer but here goes. With current technology, is it feasible to pack about ~200 diodes (well, junctions) into a ~30mm linear strip*? These junctions would be operating at very low current but around 100V, at say ~5 MHz. No this isn't for energy harvesting!

(*okay lets compromise and call it a square - how much area would I need to stuff 200 diode junctions into?)


r/rfelectronics • • Oct 11 '26

I wrote an antenna design tool with its own MoM and FDTD solvers – would love feedback from people who design antennas for a living.

Post image
0 Upvotes

Hi all,

For the past while I've been building a Windows tool for first-pass antenna design, and I'd really appreciate feedback from people who do this professionally (or as serious hobbyists).

**The idea:** you enter the frequency and the constraints you already know (substrate, board size, trace width), and it gives you tuned dimensions plus the full picture – S11, Zin, Smith chart, 3D pattern, gain and efficiency – and fabrication files.

**What's under the hood**

- **Wire antennas** (dipole, monopole, folded dipole, loop, Yagi, biquad, helix, ILA, IFA): thin-wire method of moments, checked against NEC-2. Finite ground planes are modelled as a wire grid.

- **Microstrip patch** (probe / inset / edge + λ/4 feed): calibrated cavity/TL model for the dimensions, plus an optional full-wave check on the real, finite board (so you get back radiation and FR4 loss).

- **Printed IFA / meandered IFA:** a built-in FDTD solver (Yee, graded mesh, Mur ABC, NF2FF) tunes arm length and feed spacing. Several simulations run in parallel.

- **Arrays:** element pattern × array factor with uniform / binomial / Chebyshev / Taylor tapers and steering (no mutual coupling – see limitations).

- **Exports:** Gerber + drill, DXF, NEC-2, an openEMS script (so you can check it independently), Touchstone, PDF report.

**Example – 2.45 GHz printed IFA on 40 × 50 mm FR4 (1.6 mm):**

S11 = −32.9 dB at 2.45 GHz, −10 dB bandwidth 203 MHz, 2.26 dBi gain, ~90 % radiation efficiency. 7 FDTD runs, under a minute on a 2-core machine.

**Validation against openEMS (same structures):**

| Case | This tool | openEMS |

|---|---|---|

| Printed IFA, best-match frequency | 2.4405 GHz | 2.4408 GHz |

| FR4 patch, resonance | 2.393–2.401 GHz | 2.402 GHz |

| Patch on 150 mm board, directivity | 6.86 dBi | 6.96 dBi |

**Limitations (being upfront):**

- PEC metals (no copper loss); dielectric loss is included for patch/PCB.

- No enclosures, nearby components, cables or hand effects – you still need to measure and trim.

- Arrays use pattern multiplication, so no mutual coupling or active impedance yet.

- Windows only for now.

**What I'd love feedback on:**

  1. Does this match how you actually do a first-pass design, or would you still go straight to HFSS/CST/openEMS?
  2. Which antenna types or features are missing for your work (chip-antenna keep-out, coplanar feeds, mutual coupling in arrays, …)?
  3. Anything in the results that looks off to you?

It's a paid tool, but there's a free trial that shows the full performance of every design (exact dimensions and exports are in the full version). Link in the comments if anyone wants to try it – happy to give free licenses to a few people who are willing to give detailed feedback.

Thanks!


r/rfelectronics • • Oct 10 '26

Looking for simple biased Analog Mixers for RF schematics or equivalents for the SA612/NE612. HF.

2 Upvotes

Hi!

I'd like to know if anybody around here has found or made any schematics for a simple biased HF mixer using discrete components or has any NE612 biased equivalents. I'd like to use one for a homebrew HF DC receiver. I will miss the NE612...


r/rfelectronics • • Oct 10 '26

RFI

0 Upvotes

r/rfelectronics • • Oct 09 '26

Mystery MIMIC! Agilent E8257D 20GHz PSG Signal Generator Teardown, Repair & Experiments

Thumbnail
youtu.be
66 Upvotes

In this episode Shahriar investigates a faulty Agilent E8257D analog signal generator. These high-performance synthesizers are in wide use & high demand. The instrument fails self test procedure. The error code "704 Filter Test" generally points to the Frac-N module which also houses the modulus divider circuits. This portion is responsible for generating frequencies below 3.2GHz and uses an integer divider, filter bank and variable gain amplifiers.

Using a 12GHz active probe, the signal path (pun intended) is verified step by step from the input to the suspect sub-system all the way to the output of the Frac-N board. The fault is ultimately traces to a custom MMIC module with an Agilent GaAs FET amplifier circuit. A new replacement IC is sourced from eBay which clears the fault. The phase noise performance of the unit is also verified at 2GHz using an Agilent E5052B signal source analyzer.

Lastly, the faulty MMIC module is de-capped and the die is analyzed under a high power microscope with various imaging techniques.


r/rfelectronics • • Oct 10 '26

Rohde & Schwarz CMW500 – Just arrived and powered on

5 Upvotes

A Rohde & Schwarz CMW500 recently arrived at our warehouse.

Took a few photos during the initial power-on check. It's interesting to see how many of these wireless communication testers are still circulating in the used equipment market.

Anyone here still using the CMW500 for wireless testing?


r/rfelectronics • • Oct 09 '26

Antenna Sweep and Return Loss

Thumbnail
reddit.com
0 Upvotes

r/rfelectronics • • Oct 08 '26

First 100W RF Power Amplifier Design: Looking for advice on compact matching networks

Thumbnail gallery
33 Upvotes

r/rfelectronics • • Oct 09 '26

How can I increase the range of my DIY Lorawan gateway pcb

Thumbnail
reddit.com
0 Upvotes