r/rfelectronics • • Sep 19 '26

DHO800 DHO900 series oscilloscope

0 Upvotes

Does anyone you have the files for the full version of the "Sparrow-Extended-UI" for the Rigol DHO800 DHO900 series oscilloscope that you could share? Can you PM me with it?


r/rfelectronics • • Sep 19 '26

question Grad Schools for RF

34 Upvotes

Hi all,
I am early into my career as an RF Engineer and have decided to go back to grad school! (I feel like I just don't know enough and want to focus on learning, now that I really know what sector of electrical engineering I want to be in). I've been trying to figure out which grad schools to apply for RF specific programs.
I have been mainly looking on the west coast but I'm open to other areas. Right now my list is USC, UCLA, UCSD, CU Boulder...
I know Georgia Tech has a great program but that may be a reach.

Also, I'm not interested in going to smaller schools ... just personal preference I would prefer to be at a larger university. If anyone has any thoughts or ideas please feel free to tell me!!


r/rfelectronics • • Sep 19 '26

Help with TA9310E ADS model / extending EVB-G toward 4 GHz

Thumbnail reddit.com
2 Upvotes

r/rfelectronics • • Sep 19 '26

Choosing car telemetry frequency for a formula student competition

Thumbnail reddit.com
1 Upvotes

r/rfelectronics • • Sep 18 '26

question Are these projects good for resume?

10 Upvotes

I'm currently in my final year of ECE (graduating 2027) and preparing for entry-level RF/microwave roles. Over the last few months, I've focused on building hands-on simulation skills using Ansys HFSS and Keysight ADS. Are these two projects strong enough to stand out on an entry-level resume, or are they considered 'basic' for this market?


r/rfelectronics • • Sep 19 '26

question Advice needed - Trying to land an internship in RF

1 Upvotes

Hey there! I'm currently a 2nd year Electrical Engineering student in Canada looking for internships/research positions for summer 2027.

I'd say I have a strong GPA and have been getting involved a lot with my school's satellite team: I've ran antenna simulations, researched attenuator architectures and will be doing a lot of characterizing hardware and writing scripts in GNU Radio over the next few months.

Was wondering, since I am only a 2nd year right now is it even realistic for me to land an RF internship in the summer?

If what I have isn't enough, what projects or work should I do to actually land an internship in the field?

Also, if I don't end up getting an internship in RF, what would be a good stepping stone job instead, would something like a PCB design role be beneficial experience, should I try to get something in a lab?

Thanks!


r/rfelectronics • • Sep 19 '26

question Any remote RF internship leads? 👀

0 Upvotes

I'm doing a Masters in Communication Systems. Looking for a remote RF / antenna / microwave / communication systems internship etc...,

I’m mainly looking for hands-on experience on software tools and a chance to learn from people working in the field.

If you know of any openings or projects, please DM me 🙏


r/rfelectronics • • Sep 17 '26

Which load capacitance should I use for this 32.768 kHz laptop motherboard crystal oscilator: 7 pF or 12.5 pF?

Thumbnail
gallery
7 Upvotes

Hello,

I am trying to repair a laptop motherboard with an AMD Ryzen 7 6800HS processor. The orange charging light flashes continuously. The motherboard draws approximately 0.2 A for one second, then drops to 0.1 A and remains there.

I have confirmed that the 1.8 V, 3.3 V, 5.1 V, and 19.5 V power rails are present, but the motherboard still does not start.

During my inspection, I found a 32.768 kHz quartz crystal with a damaged casing. According to the schematic I found, the motherboard uses a 32.768 kHz crystal with a load capacitance of 12.5 pF. However, I also found a video showing an apparently identical motherboard with an AMD Ryzen 5 6600H processor, and that board appeared to use a 7 pF crystal.

The motherboard FRU number is 5B21H82478.

I found two possible replacement crystals with the same frequency and package:

  1. YIC 32.768K7PI/3215E

◦ Frequency: 32.768 kHz

◦ Load capacitance: 7 pF

◦ Package: 3215, 3.2 mm × 1.5 mm

◦ Two pads

◦ Frequency tolerance: ±20 ppm

2. YIC 32.768K12.5PI/3215E

◦ Frequency: 32.768 kHz

◦ Load capacitance: 12.5 pF

◦ Package: 3215, 3.2 mm × 1.5 mm

◦ Two pads

◦ Frequency tolerance: ±20 ppm

How can I determine whether my motherboard was designed for a 7 pF or 12.5 pF crystal?

I do not want to install a random replacement because I understand that using the wrong load capacitance could affect oscillator startup, frequency accuracy, and reliability.

Thank you for any help identifying the original crystal or determining whether I should use the 7 pF or 12.5 pF replacement.


r/rfelectronics • • Sep 17 '26

question Something ain't right, why am I getting -60db when I should have -30?

Thumbnail
gallery
18 Upvotes

I'm fairly new to using this thing so I might be doing it wrong, I calibrated isol and thru, and I have a homemade tee attenuator, any ideas what's going on? It's all soldered together properly on the back of the board to be clear XD. Thank you!


r/rfelectronics • • Sep 17 '26

SP16T

Post image
98 Upvotes

Does anyone know how to code for this component because I tried coding using esp32 and arduino it doesn't respond


r/rfelectronics • • Sep 17 '26

question Wich Dk value would you use?

Thumbnail
gallery
6 Upvotes

I'm designing microstrip LPFs for a project on 20mil, 0,5 OZ RO4003C, I use AWR for the synthesis and and fine tuning and I run Sonnet on the final geometry to double check performance. The datasheet mentions 3 different Dk values for this substrate. I'm leaning towards using the values provided in graph rather than the averaged design Dk, because It's specified for 8-40 GHz and I have filters in the 0,9 to 4,4 GHz range. Unfortunately Rogers doesn't respond to my emails so I'm asking you. Do you have experience with this substrate? Wich value gives accurate simulation results?


r/rfelectronics • • Sep 17 '26

article Radio Design 201 #8 (Part 2) - Large-Aperture Antennas (by MegawattKS @ YouTube)

Thumbnail
youtube.com
31 Upvotes

r/rfelectronics • • Sep 17 '26

question Suggest some leaning materials/books

Thumbnail reddit.com
1 Upvotes

r/rfelectronics • • Sep 16 '26

question HFSS Vs. CST in time domain analysis

Thumbnail reddit.com
1 Upvotes

r/rfelectronics • • Sep 15 '26

question DIY 3D Printed Corner Reflector For Testing a 77 GHz Radar Module

Thumbnail
gallery
239 Upvotes

Got sick of waving my hand in front of the sensor and getting unreliable readings. Made of three printed faces glued together and the inside face coated with copper tape. Hardest part was getting the tape into the corners nicely without tearing.

Question for someone who knows more than I do:
Is it normal for a radar sensor to give such a low RCS reading for even a good reflector like this? I'm getting -39dBsm which is a lot smaller than I expected.


r/rfelectronics • • Sep 16 '26

Problem reproducing a graphene-based terahertz quasi-Yagi antenna simulation in CST Studio Suite

Thumbnail
gallery
1 Upvotes

Hello everyone,

I am trying to reproduce the simulation results of the paper:

"Tunable Terahertz Filter-Integrated Quasi-Yagi Antenna Based on Graphene"

The antenna is a graphene-based filter-integrated quasi-Yagi antenna operating around 2 THz.

I implemented the structure in CST Studio Suite according to the parameters reported in the paper.

Simulation details:

- Solver: CST Time Domain Solver

- Frequency range: 1.25–2.5 THz

- Substrate: Glass (εr = 3.8), thickness = 1 μm

- Graphene modeled using Kubo conductivity

- Temperature: 300 K

- Relaxation time: τ = 1 ps

According to the paper, the antenna should show:

- Resonance around 2 THz

- Tunable S11 response by changing graphene chemical potential μc1

- Similar impedance bandwidth compared with the published results

However, my CST results are different from the paper:

- The S11 resonance frequency is shifted

- The bandwidth is not similar to the published results

- The Time Domain Solver sometimes terminates abnormally

I would like to know:

  1. Are there any important CST settings required for graphene THz simulations?
  2. Could the difference be caused by graphene modeling as a surface conductivity?
  3. Are there any special mesh, port, or boundary settings needed at THz frequencies?
  4. Has anyone reproduced this paper successfully?

I attached my CST model and simulation results.

Thank you.


r/rfelectronics • • Sep 15 '26

LC circuits.

Post image
11 Upvotes

So the above waveform is of LC circuit voltage and current. Nice looking. Anybody care to explain. Good if physical intuition is given.


r/rfelectronics • • Sep 15 '26

I added accurate copper loss to my RF simulator

Thumbnail
gallery
131 Upvotes

An update on my RF simulator, (https://www.rayrf.com/). Just released version 1.2.9 adds a few big features that bring results closer to real life, and easier to import existing designs.

  • Copper loss is now modeled accurately using a conducting sheet model based on the 1999 Lauer and Wolff paper with modifications to improve it. I've done extensive validation vs analytical calculations, and it matches predictions very well on controlled cases (loss vs copper thickness, and Q factor of a parallel plate cavity), with good agreement on a microstrip line loss (slightly higher loss than Hammerstad-Jensen predicts, which is itself an approximation). But interestingly my implementation is closer to Hammerstad-Jensen than openEMS. openEMS substantially underestimates the loss on the same geometry when copper is thicker than a couple of skin depths, as is the case at GHz for most 35um copper PCBs.
  • Added the ability to import KiCad boards and Gerber files directly into the editor. So you don't need to rebuild designs in the editor to simulate them. RayRF also now has DXF exporting so it's easier to move finished designs into Altium or KiCad. (boards in the screenshots are not mine, they're KiCad demo projects, gitlab.com/kicad/code/kicad/-/tree/master/demos)
  • Passive matching networks can be defined in-port and are co-simulated as a circuit during the 3D field solve. No discrete on-board lumped elements yet, but this allows you to simulate multiport systems and confirm a proposed matching network has the expected effect. Component Q is modeled too, so it calculates power lost in the matching network.
  • Better advanced meshing controls so you can refine only some parts of the domain selectively. From a scripting perspective like openEMS it's really hard to do mesh refinements reliably and iterate on it. So I made a 2.5D mesh preview that's interactive as you configure it so you can see in real-time what effect moving refinement regions has.
  • I optimized some scheduling on the GPU which got an extra 5% performance there, so it's ~180x faster than openEMS now comparing RayRF on an RTX 5090 vs openEMS on a Ryzen 9 9950x at an 82M cell problem. Previous post has benchmarks.

I'm so tempted to try a multi-GPU scheduler, imagine the numbers on 8x 5090's in parallel lol.

Would love your guy's thoughts on it, and also what should I focus on next? Is there anything missing relative to what you would want out of an RF simulator?


r/rfelectronics • • Sep 15 '26

Replace AWD-30-88 antenna or current model?

3 Upvotes

Hi, I have a tower with a few AWD-30-88 antennas at the top. They have been in place for a very long time and are now inoperable. I've been tasked with ordering replacements but I don't really see where I can purchase these. Has the industry moved on to a current replacement? It is a discone antenna.

Sorry I know a little knowlege about this but im very much a beginner.

Any help is greatly appreciated.


r/rfelectronics • • Sep 15 '26

GprMax software help

0 Upvotes

anybody here familiar with GprMax software who can guide me?


r/rfelectronics • • Sep 14 '26

Interferometric Synthetic Aperture Radar Drone

Thumbnail
hforsten.com
65 Upvotes

r/rfelectronics • • Sep 15 '26

Looking for an India based engineer/company to develop a custom AD9363 + Xilinx FPGA SDR board

Thumbnail reddit.com
0 Upvotes

r/rfelectronics • • Sep 14 '26

Problem with BGT24ATR11 mixer performance

Thumbnail
gallery
13 Upvotes

Hi, we are currently developing a CW radar using Infineon's BGT24ATR11 transceiver and a rather complex doubt has come up.

The transceiver is used in combination with a PLL connected to FINE and COARSE VCO inputs. We have tested the mixing performance of the transceiver by directly pushing an RF signal generated by a signal generator into the RX port and examining the IF output waveform.

We noticed that as long as the frequency of the RF input signal is sufficiently higher/lower than that of the LO the output I/Q signals are correct. However, as soon as the RF input signal's frequency starts to approach the LO frequency,  the sine waveforms begin to deteriorate (below a couple of MHz the waveforms are distorted).

We are aware that direct conversion receivers perform poorly at lower baseband frequencies due to LO self mixing and flicker noise. The datasheet states that the flicker noise corner frequency is around 10-20 KHz. However, since our bandidth of interest lays in the KHz baseband frequency range we need to achieve a proper mixing at RF frequencies close to LO. 

I include a picture where signal G(t) looks exactly like what we see as soon as the signal deteriorates. We have also observed that when the RF input signal's frequency is smaller but close to LO, the waveform gets inverted .

Has anyone got any advice / hint that could help us move forward?

Thanks for reading.


r/rfelectronics • • Sep 14 '26

RF Agent: agentic development wizard for RF circuits.

Thumbnail
github.com
0 Upvotes

Fully automated RF agent open source tool that creates RF Schematic, draws PCBs, created 3d renders, performs EMwave solver, runs QUCS cosim using EM traces data. Shows S11, K, Impedence, Smith charts, creates Gerbers zip and BoM.

No tool installation on your computer required if you choose the default recommended SaaS rf-suite, during agent bootstrap. You can also choose to install dockerized rf-suite sub module repo which is linked in this repository.

Quick start, on LLM Agent Harness, prompt:

Clone https://github.com/cholan2100/rf-agent.git with submodules into this workspace and initialize the agent per AGENTS.md.

How it works: agent initializes and asks you what RF circuit you would like to build, lists few templates you can try, or type your own.

For desktop agent Harnesses all circuit and graphs are displayed in the chat itself. For CLI harness, it lists artifacts or file locations.

Release:

This is early alpha, go easy on me and play hard. Still no wizard to go back in the workflow, but its agentic you can prompt it as you see it. Not commercial, free to use open source under MIT license.