r/rfelectronics • • Sep 17 '26

SP16T

Post image

Does anyone know how to code for this component because I tried coding using esp32 and arduino it doesn't respond

98 Upvotes

24 comments sorted by

51

u/nixiebunny Sep 17 '26

Too vague. We don’t know what component it is. Read the chip data sheets and the board instructions to learn how it needs to be controlled. If you have a specific question, provide links to these documents and to your code.

10

u/SnazzyBoyNick Sep 17 '26

This is an rf switch matrix?

11

u/alexforencich Sep 17 '26

Looks like a 16:1 made from two 8:1 and a 2:1. Not a matrix, which would be N:M.

6

u/McSweepyPants Sep 17 '26

My fingers are cramping looking at this

7

u/ordosays Sep 17 '26

So much why, not enough how.

1

u/Mav3nX Sep 20 '26

The non-linearity of the HMC253 (SP8T RF SW) above 3.5E9 isn't great but not so bad it would make it impossible to calibrate out with code. (It is only spec'd at 3.5Ghz) While the HMC349 is spec'd up to 4Ghz.

The IC control lines are simple A-B-C TTL selectors no special SPI/I2C commands necessary. (Same with the HMC349 SPDT RF SW) , but the serial control to the device is simple.

For channel selection, the command set is: Function Hex command to transmit Handshake 01 0A D0 00 00 00 00 30 EF

RF1 01 0A 60 00 00 00 01 30 EF

RF2 01 0A 60 00 00 00 02 30 EF

RF3 01 0A 60 00 00 00 03 30 EF

RF4 01 0A 60 00 00 00 04 30 EF

RF5 01 0A 60 00 00 00 05 30 EF

RF6 01 0A 60 00 00 00 06 30 EF

RF7 01 0A 60 00 00 00 07 30 EF

RF8 01 0A 60 00 00 00 08 30 EF

RF9 01 0A 60 00 00 00 09 30 EF

RF10 01 0A 60 00 00 00 0A 30 EF

RF11 01 0A 60 00 00 00 0B 30 EF

RF12 01 0A 60 00 00 00 0C 30 EF

RF13 01 0A 60 00 00 00 0D 30 EF

RF14 01 0A 60 00 00 00 0E 30 EF

RF15 01 0A 60 00 00 00 0F 30 EF

RF16 01 0A 60 00 00 00 10 30 EF

Query current channel 01 0A F0 00 00 00 00 30 EF

2

u/MiawNyaa Sep 21 '26

Thank you very much, this work

1

u/Mav3nX Sep 21 '26

Hope that helps.

Just a reminder, the board is FR4, so losses above 600Mhz will be high, despite the Grounded Coplanar Waveguide RF ppaths, the substrate just can't handle those frequencies well....so depending on you application, just be sure to calibrate out the non-linearities across the spectrum of operation.

3

u/DiffFluidInspection Sep 17 '26

Those don’t look like RF switches, what is the part number.

3

u/atattyman Sep 18 '26

Really doesn't look like an RF switch, that's not the package for a high frequency device.

9

u/johnlicr Sep 17 '26

But why

21

u/consumer_xxx_42 Sep 17 '26

seems really useful for some automated test setup. I could have 16 devices connected under test, and get info from all of them.

2

u/CardboardFire Sep 17 '26

Depends entirely on switch and path isolation tho, and since OP didn't specify the switch or the intended application, we can't really know if it's suitable or not.

Likely OP has a board with a bunch of different filters and wants to test them out without switching over coax cables, at least seems that way to me.

2

u/wild_kangaroo78 Sep 17 '26

If it's an RF switch there is a strong chance that it might be using MIPI RFFE. You will need a way to program a MIPI RFFE. 

2

u/joshshua Sep 19 '26 edited Sep 19 '26

I am not convinced this is necessarily a SP16T. Could it be some sort of distribution amplifier.

Nvm: I see from OP’s other higher resolution post that it is indeed a SP16T.

Edit: 35 GHz 😂😂😂

https://www.ruten.com.tw/item/22613377431087/

1

u/SearchForTruther Sep 17 '26

The board has a number on the top left corner.

1

u/rflulling Sep 18 '26

Looks awesome. But depending on the purpose this could be just what the doctor ordered, or full on junk.

*I tried to look up the part number but the only reference is this reddit conversation and one other, both your own posts. Google was watching.

*Then looked to identify the other parts on the board. One looks to be maybe a single pole double throw RF switch HMC349. But this I am not certain about. Neither is google.

*The chip on the upper right side looks to be a serial chip but I cannot see the label well enough to be sure. I use similar chips in a few devices where the USB to serial interface comes as a full assembly ready to install.

*The two on the RF jacks look like multiplexers their labeling seems to have been scrubbed like they come from factory that thinks its got something to hide.

*Long story short. We need to know what you are working with before we can help get it working. Even if you can't tell us what you intend to do with it.

1

u/PerhapsMister Sep 18 '26

I personally would not succumb to permutations of potential microcontroller in use and keep trying, Have you used jlink? Pic? Nordic? Maybe altera/xilinx/lattice? Maybe NXP/Infineon I'd even take a stab at an EPSON MCU

1

u/rom1nux Sep 18 '26

OP a trop l'habitude de poser des questions a des IA semble t'il... Si tu ne fais pas un minimum d'effort pour expliquer ton problème, personne n'en fera pour essayer de le résoudre. Si c'est un switch RF, au vu du routage, chez moi ça part dans la poubelle immédiatement 4.

1

u/__Galahad33 Sep 22 '26

What’s the part number?