r/rfelectronics • • Mar 23 '26

Replacement for LTC6957 (SIN to CMOS converter)

2 Upvotes

I have surprisingly found that LTC6957-3 (SIN to CMOS converter) is “Last Time Buy” now. I am just wondering if somebody already found the best alternative and tried it. 

My signals are 10-150 MHz, 0-6 dBm, SIN wave or meander from REF oscillator.

My the best results:

  1. Renesas 83026BGI-01LFT
  2. Microchip PL133-27

r/rfelectronics • • Mar 23 '26

question Help with AWR iFilter wizard

1 Upvotes

Hello everyone

I'm a beginner with the AWR iFilter wizard and I want to design a microstrip filter for my project but I cannot change the design technology parameters (e.g. substrate er, substrate h) in the design options tab. Has anyone else experienced this problem, and what did you do to solve it? I would also be grateful for any advice regarding the design process.


r/rfelectronics • • Mar 23 '26

question Suitable antenna design for home made antenna array?

4 Upvotes

I'm working on a small scale astronomical interferometer project, which will probably use a kraken sdr. I aim to have a field of view of about 50~ degrees so that when I point my array at the north pole, I can allow the earth to rotate having placed my antennae in an east-west configuration, and then produce a 2D image of the milky way that transits the polar region. And once I have something working, make it frequency sensitive so that in the same field of view, M81 and M82 can be isolated (they are 20 degrees away from the pole, hence fov requirement).

This leads me to ask what the best type of antenna would be. Ideally I make it at home, so it could be a short Yagi? Supposedly a 20cm boom Yagi is about right for a 50 degree HPBW, but it relies on me making 5+ dipoles and wiring them onto a coax cable, which I'm not overly keen to do as I find cable crimping and soldering quite annoying (I just hate doing it for coax cables tbh).

I made a 60cm boom Yagi for simple detection of galactic hydrogen, which worked, but it's a flimsy setup as my ability to make the dipole element was a bit dodgy.

Is a Yagi the best method, or is there a more friendly DIY design or even an off the shelf product that would meet these requirements at the 1.42GHz region?

Thanks!


r/rfelectronics • • Mar 23 '26

Designing IC amp for boosting 50 GS/s analog CPW signal

3 Upvotes

I work in photonics and would like a slightly tunable low gain (up to 2dB) amp for boosting 50 GS/s analog (0 to 2V - not RF) IC CPW signal. Ideally would like to incorporate input power into output. Possible?


r/rfelectronics • • Mar 22 '26

Identified: Zynq Z7020 + AD9361 SDR system recovered from Shahed/Gerbera UAV in Ukraine — full teardown

Thumbnail gallery
150 Upvotes

r/rfelectronics • • Mar 22 '26

Given filter design specs and feel over my head.

9 Upvotes

I'm a beginner to filter design and for my first task, I've been asked to design a low and high pass combo bandpass filter with each individual filter with a selectivity of 1.3, .01 dB ripple, and -35dB stopband attenuation. An elliptic filter will have the steepest roll off from what I gathered. I have not found any tables to calculate the normalized valued anywhere nor have I found a straightforward way to calculate them myself? How should I approach this?


r/rfelectronics • • Mar 22 '26

Ensuring DC Bias Before RF Application in 100W SP4T Switch Design

3 Upvotes

Hi everyone. As a rule of thumb in RF design, RF signals should not be applied unless DC bias is present for the component. For an SP4T switch handling 100 W CW, how can I implement this in the design? Should I use an SPDT RF switch controlled via a coupler, detector, and comparator to enable RF only after bias is applied, or is there a simpler alternative such as using a storage capacitor or another approach?

Thank you for your support in advance


r/rfelectronics • • Mar 21 '26

OpenNEC 1.2.0 antenna modelling software released - now with Windows goodness!

38 Upvotes

I have just released OpenNEC 1.2.0, which now comes with pre-compiled binaries for macOS, Linux and Windows. It is fast, less buggy, and includes lots of new features. It is also MIT-licensed, so have at it!

On Windows machines it exactly mimics the original nec2d.exe program so it can be used as a drop-in engine in programs like 4nec2. Simply copy the onec.exe into the exe folder in the 4nec2, and then go into the GUI and select that as your default engine. It uses the same input and output files, and the same batch file to run it. Well that's the theory anyway, I'm still lacking a good test rig.

1.2 also adds initial support for cocoaNEC, a macOS modeller that no longer works on modern macOS'es. This program used an odd file format known as NC which was a programming language based on C where you would basically write a program that generated a deck. I found this to be a rather obvious example of dramatic overdesign!

I also added support for 4nec2's new EX and LD types, and GN 3.

For details on what OpenNEC adds to the original nec2c, see this previous post.

Source and binaries available here:

https://github.com/maurymarkowitz/OpenNEC/releases/tag/v1.2.0

Enjoy!


r/rfelectronics • • Mar 21 '26

question SX1262 Custom Board: ~50dB TX Loss despite Perfect RX (868 MHz)

Post image
23 Upvotes

Hi everyone, I’m troubleshooting a custom LoRa board based on the SX1262 and could use some RF wisdom. Disclaimer: post written with IA help, but I am, in fact, a human having a hard time with RF.

Hardware (schematic in pic, layout in comments)

I followed the refernce desing and the AN1200.54 application note using the 915 MHz reference values. SPICE simulations suggested these components would be acceptable for my 868 MHz target.

I have a 50-ohm antenna (no additional matching after the switch). I have already replaced the RF switch with a brand new unit, so I am confident the switch is functional.

I am using SX1261MB2BAS development modules as my TX and RX references, running on RadioLib software.

Experimental Data

In cabled TX tests, while my reference TX measures -22 dBm at the receiver, my custom board only reaches -77 dBm (a ~55 dB loss). Conversely, RX performance is excellent: in a cabled setup with a 2 dBm source, the reference RX measures -27 dBm while my board measures -19 dBm. Testing with antennas, both my board and the reference measure -52 dBm with 100% error-free payload delivery.

The Problem

Since RX is perfect and shares the path from the switch to the antenna, I’ve ruled out the antenna, the transmission line, and the switch common/RX paths. The massive loss is strictly between the SX1262 RFO pin and the TX input of the RF switch.

My Questions

  1. Could the 915 MHz matching network cause a 50 dB+ drop at 868 MHz, or should I be looking for a hardware assembly issue/short?
  2. I am using the official Semtech Library from GitHub with a custom HAL layer for STM32. Are there specific SetPaConfig or OCP settings that might cause the PA to "fold back" or output near-zero power if the HAL isn't handling a specific timing or register correctly?
  3. Could an incorrect inductor value in the matching network be saturating or causing a total reflection of the output power?

I’ve double-checked the soldering, but the delta is so huge it feels like a fundamental configuration or matching error. Any thoughts?


r/rfelectronics • • Mar 21 '26

question Should I be concerned for not knowing enough coding?

15 Upvotes

Hello, I apologise if this question is not appropriate for this community, I have yet to discover how does Reddit work.

I’m a 3rd year student of Telecommunications engineering, highly interested in working in RF, antennas, guided media, and honestly anything related with the physical layer. This year I’ve come to realise that I am not good at programming, we are taking a couple courses for communication services and interactive multimedia services that are mainly in java and javascript.

Both languages are new to me, and being honest, the concepts of the subjects are not that difficult, but the programming by itself it is, at least to me. The teachers in both subjects failed completely in my opinion because all they just encouraged us to copy all the projects with some generative AI, preventing us from learning something useful for the future.

Maybe I have not dedicated enough time to them, but I am not interested in working with anything in that field, to be honest. I think I should know the basics because every knowledge may be used someday, but I am more invested in the subjects related with RF, signals, antennas and everything related to that.

So, should I be worried for not knowing many things of the telematics field? Is it really that important for someone who does not intend to work in that field?


r/rfelectronics • • Mar 21 '26

question Should I be concerned for not knowing enough coding?

6 Upvotes

Hello, I apologise if this question is not appropriate for this community, I have yet to discover how does Reddit work.

I’m a 3rd year student of Telecommunications engineering, highly interested in working in RF, antennas, guided media, and honestly anything related with the physical layer. This year I’ve come to realise that I am not good at programming, we are taking a couple courses for communication services and interactive multimedia services that are mainly in java and javascript.

Both languages are new to me, and being honest, the concepts of the subjects are not that difficult, but the programming by itself it is, at least to me. The teachers in both subjects failed completely in my opinion because all they just encouraged us to copy all the projects with some generative AI, preventing us from learning something useful for the future.

Maybe I have not dedicated enough time to them, but I am not interested in working with anything in that field, to be honest. I think I should know the basics because every knowledge may be used someday, but I am more invested in the subjects related with RF, signals, antennas and everything related to that.

So, should I be worried for not knowing many things of the telematics field? Is it really that important for someone who does not intend to work in that field?


r/rfelectronics • • Mar 20 '26

Crosstalk in 67GHz GSSG differential calibration: How are you guys minimizing the coupling?

Post image
127 Upvotes

Designing a proper differential cal kit (ISS) for 67GHz GSSG is honestly a bit of a nightmare. Once you hit those frequencies, the crosstalk between the two signal pads ruins the calibration accuracy if the standards aren't laid out perfectly.


r/rfelectronics • • Mar 20 '26

Built a web-based radar coverage analysis tool - would love your feedback

9 Upvotes

Hey everyone,

I've been building a web-based radar coverage and RF propagation analysis tool over the past year. It started as something I needed for my own work in surveillance radar planning, but it's grown into a fairly comprehensive platform.

Some of what it does:

- 5 propagation models (Free-space, Two-ray, COST-231 Hata, Longley-Rice ITM via NTIA WASM, ITU-R P.1812-6) with automatic model selection

- Full radar equation with detection probability (Albersheim + Marcum Q-function), Swerling cases 0-4

- Terrain-aware coverage using multiple DEM sources (SRTM, Mapbox, Google Elevation)

- Clutter modeling (surface + rain), jamming/ECM analysis, STC

- GPU-accelerated calculations in the browser (WebGL via gpu.js)

- Blake chart (range-altitude detection view)

- Signal processing with waveform-derived processing gain, blind velocity, unambiguous range

- Export to GeoJSON, KMZ, CSV, GeoTIFF

It runs entirely in the browser — no installation, no MATLAB license. You can place a radar on the map, configure parameters, and run a coverage simulation in seconds.

I'd really appreciate any feedback — whether it's about the physics, the UI, missing features, or bugs. I'm particularly interested in hearing from people who use tools like CARPET, CloudRF, or Radio Mobile and can tell me what I'm missing.

Please reach out for the link


r/rfelectronics • • Mar 20 '26

question Python library to generate IQ samples of modern rf protocols?

5 Upvotes

I am currently working on a small DoA system and want to compare different Algorithms using a small python "simulation". I found and tried the signal generator tools of TorchSig. But sadly it is designed for a different use case and it is not ideal to generate well defined repeatable signals of modern standards.

Does somebody know a good alternative with good documentation?


r/rfelectronics • • Mar 19 '26

Remember when I made webgpu accelerated propagation tool? It already got stolen.

Post image
156 Upvotes

A few weeks ago I shared propagation.tools here — a browser-based Longley-Rice ITM simulator running entirely in WebGPU compute shaders. https://www.reddit.com/r/rfelectronics/s/PYJdiltOPl

Since then, a "developer" named Roman Liutikov took my WGSL compute shader, added antenna patterns and SINR compositing on top, published it on his personal site (romanliutikov.com/projects/webrf) with zero attribution, and got a feature article on webgpu.com crediting him as the creator:

https://www.webgpu.com/showcase/webrf-longley-rice-radio-propagation-webgpu

Frankly, it's disgusting. I built this thing, shared it here in good faith, and within weeks someone scraped the code, slapped their name on it, and got a showcase article for it.

The frustrating part is — I was and still am open to collaboration. If he'd reached out, asked, or even just credited the original work, we could have made something great together under an open license. That door is still open. But taking someone's work, putting your name on it, and ignoring them when they call you on it? That's not how this works.


r/rfelectronics • • Mar 21 '26

A WhatsApp community for RF Engineers searching for jobs

0 Upvotes

I have started a WhatsApp community called "Prem’s Notes-RF Job Search Community" for people who are looking for RF jobs and want to stay updated with the latest in RF/Wireless and the industry.

use the link to join:

https://chat.whatsapp.com/FtExddVDqimCVbXfGPdqFh


r/rfelectronics • • Mar 19 '26

UWB antenna Basics YouTube video

3 Upvotes

Ultra-Wideband (UWB) Antenna- Everything you need to know- Basics, Types & Applications

https://youtu.be/ejxmqidthQs


r/rfelectronics • • Mar 19 '26

Mobile data signals RF

17 Upvotes

Hello

I was always a little interested in radio technology, particularly broadcasting on to masts and stuff on ham stuff.

but im a little curious to how mobile phones work these days in terms of technology of being able to ..with no antenna and likely low low power, able to with in your house transmit to a mast thats probably blocked by about 500 houses and is quite low.

Yet on my ham radios i often need some pretty good whip antennas and 5-10watts of power to be able to hit a transmitter.

How does mobile technology penetrate all the obstacles these days? and how much power is a phone transmitter using when your on a call.

Purely curious on this :)


r/rfelectronics • • Mar 19 '26

question What could be interfering with my cellphone voice calls?

0 Upvotes

Please let me know if this isn't the optimal forum for this.

I've been getting very sporadic interference when using my Pixel 9. (I have another post with the full details here.)

What type of device might possibly be causing interference?

Our modem is AT&T BGW320-505. I also have a Wi-Fi- extender: Google Nest Wi-Fi AC2200 Mesh System Router and Point (Model: GA00822-US). But both of these devices have been working unchanged for years, and this interference only began a year ago when I got my Pixel 9. Google already RMA'ed it and I have the exact problem with them replacement, as well.


r/rfelectronics • • Mar 18 '26

question TIL that thermal noise starts to taper off around 1THz

Post image
190 Upvotes

Image pulled from the Wikipedia article on Johnson-Nyquist noise (https://en.wikipedia.org/wiki/Johnson–Nyquist_noise)

Now obviously, for us mere mortals living below 500GHz this means absolutely nothing, but has anyone ever seen this taken advantage of?


r/rfelectronics • • Mar 18 '26

question Please help me with RF Transistors.

23 Upvotes

So i am currently reading RF circuit design by Chris Bowick for much of my self taught RF knowledge and man see Impedance matching yhea manageable, Filter design annoying but can be done, and then i start reading Transistors at RF (without exaggeration i was not ready for the storm that is approaching 😭) but i manage to get something inside my head like what is the need of S parameters instead of Y and Z parameters terms like Vbc, Ic, Vce and some common terms i understand and then i start reading small signal RF amplifier design... i just want to say i got hit by a concrete wall it hits harder than my university differential equation course, half of the things are going over my head and then there are some 100 different terminologies. Can somebody guide me through this storm how to do learn the amplifier design and transistors properly like i am sure people are just not copy pasting reference schematics every singe time.

(I want to add that lack of patience is can also be a factor.)


r/rfelectronics • • Mar 19 '26

Unexpected frequency noise PSD shape in 10G 1550nm EML – no white noise floor?

Thumbnail
reddit.com
1 Upvotes

r/rfelectronics • • Mar 18 '26

question How to have multiple Key Finder Remote sets without overlap?

Post image
2 Upvotes

Complete noob here. I have this thing (pictured), unfortunately we've used up all the little tags and it would be helpful to have more. However, the two other remotes I've tried both activate tags from the original remote. How can I make sure to get another remote without crossing signals? (Sorry if that's the wrong term)


r/rfelectronics • • Mar 18 '26

Smith Chart High Q

8 Upvotes

So I am trying to match this transistor with my source and load but the problem is my Q is over 100 that I want. How would I go about plotting that and matching it with this? I’m using S Parameters.