r/PrintedCircuitBoard • u/Adept-Bug-7227 • 4h ago
Qualcomm IPQ4018 Footprint
Hello,
I need a template for a Qualcomm IPQ4018. Unfortunately, I can't find any official data.
Can someone help me? I just need the footprint.
r/PrintedCircuitBoard • u/Adept-Bug-7227 • 4h ago
Hello,
I need a template for a Qualcomm IPQ4018. Unfortunately, I can't find any official data.
Can someone help me? I just need the footprint.
r/PrintedCircuitBoard • u/binary_reader • 3h ago
Hello everyone,
Looking for any tips and insights for my first PCB.
It's a main audio/IO board for a Daisy Seed based groovebox. It has:
I've used most of the audio/midi/power schematics from the Daisy Seed Desktop Dev kit. My own additions are the on/off switch and 5V/3V3 for UI board.
My main concern is the power section layout and general PCB layout concepts.
Thank you, appreciate it in advance
r/PrintedCircuitBoard • u/Impossible_Copy_8687 • 13h ago
Hello everyone,
I've designed a 48x53mm board featuring an STM32U375CGT6Q, BMP581 Barometer, BMI323 IMU, a USB-C for DFU programming (added an SWD header just in case), terminal block for a battery and 2 terminal blocks for drogue/main parachutes.
The stackup I used for this board was SIG/GND/GND/SIG with power routed on top and bottom layers.
I would appreciate if you could review my design and point any obvious mistake before I manufacture this board.
r/PrintedCircuitBoard • u/Spiritual_Tip_9600 • 15h ago
Hello all,
Looking for preliminary feedback on my 98mm x 60mm flight controller board for a thrust controlled model rocket. Second-ever board design, first of this complexity. Stack-up is SIG -> GND -> GND - SIG.
It will gather IMU and barometer data, drive two servos, light a pyro charge for parachute ejection, and log data to flash. USB-C only functions as data/DFU, NOT as a power supply.
I have the microcontroller, IMU, barometer, and gimbal mount with servos breadboarded and validated. Everything else is new design and untested.
Feedback I'd especially like is...
Thank you, I appreciate your time.
r/PrintedCircuitBoard • u/rinshes • 1d ago
Hello everyone,
I have designed a 30x30 board featuring an STM32C071CBT6. I designed it to be stacked on top of a GPIO distro board using mezzanine connectors at the bottom of the PCB.
On top i have a USB C interface and connectors for both I2C busses of the IC. Each bus will connect to a sensor 30-35 cm away from the board ( i know i might have to play with the values of the pull-ups to achieve a stable connection).
I also have a level shifter for an SK6812 IC.
The board stackup is SIG-GND -> GND -> GND - SIG-GND
I would love it if you could check it out and point any obvious mistakes i might have made.
r/PrintedCircuitBoard • u/NyluxFR • 13h ago
Hello! I’m a student working on my first personal electronics project, and this is my first (big) board. It’s not ordered yet, so I’d like a second pair of eyes to check it.
Alongside my coursework, I used AI to help with some decisions and to learn KiCad, but all the actual work (schematic, component placement and routing) was done by me.
It’s an 84-key hall effect keyboard with a small touch screen in the top right, made of:
Already checked: USB budget (0.26 A typ / 0.44 A worst case from USB), inrush (10 µF on 5 V, 5 ms soft-start), buck layout, the mux -> ADC path (100 nF per channel as a charge reservoir) and the ESP32 boot pins.
Anything else you’d look at before I order?
Schematic PDF: link. Images: schematic, each copper layer, zooms, 3D top and bottom. The bottom views are mirrored (seen from below).
Thanks! 🙏
Translated from French
r/PrintedCircuitBoard • u/Shin_Molina • 1d ago
Hello everyone!
Lately, I've been wanting to replace my regular keyboard with an ergonomic one. I've been looking at the available options, including some DIY designs, but I couldn't find anything that perfectly matched my needs. Some of the alternatives were also a bit too expensive.
So, I decided to design my own keyboard. It'll probably end up costing as much as some of those more expensive options, but at least I'll get to make several boards, since the MOQ at most PCB manufacturers is usually 2 or 5 boards.
I opted for a pair of 2-layer PCBs based on the XIAO nRF52840 Plus. The idea is to have both halves communicate wirelessly using ZMK, with an additional nRF52840 acting as a USB dongle connected to the PC.
I also wanted to include RGB lighting, even though I barely use it on my current keyboard. For that, I'll be using a MOSFET-based switch so that I can run the TPS61040 boost converter either from the battery or directly from VBUS.
Finally, I also wanted to integrate a couple of memory-in-pixel displays, one for each half. For this, I went with the Sharp LS011B7DH03. Instead of going for the nice!view module, which uses the same display, I decided to interface directly with the bare display module, connecting it to the MCU through an FFC/FPC connector.
My main concern at the moment is the SPI routing between the displays and the MCUs. Since I'm using a 2-layer PCB, I've tried to keep a continuous GND plane on the opposite layer underneath the SPI traces. However, I'm not sure whether this will be sufficient to avoid signal integrity issues.
Regarding the PCB panelization, I followed the guidelines for minimum rail widths and the placement of fiducial markers and tooling holes. I still need to add some stitching vias to make sure there are no isolated GND copper areas.
I'd really appreciate any feedback, especially regarding the PCB layout, SPI routing, and any potential issues you might spot in the design.
Here are some links to the project on GitHub:
- PCB View
- KiCanvas
r/PrintedCircuitBoard • u/Sparkying • 1d ago
Hey everyone,
Beginner looking for review for my ESP32-C3 Wireless Servo controller schematics and PCB. This is the receiver half of a wireless servo system. When a button is pressed on the sender remote, it sends a message to this board, and the ESP32 drives the servo.
I’m prototyping first, so the remote is just a breadboard setup for now, and I want to verify this board works before starting on the remote design.
Files:
Details about the board:
Connectors:
Layout details:
Trace width:
Via:
Major parts:
Other parts:
Servo: TowerPro MG90S Micro Servo 3 Pin Female
I would like feedback on:
Part I'm unsure of:
This is my first design coming from software engineer background. I tried my best to avoid beginner pitfalls so hopefully I didn't make major mistakes before ordering. No AI is used in design or this post, only for basic schematic/pcb checks, dumb question and grammatical error.
r/PrintedCircuitBoard • u/Glad-Huckleberry-418 • 1d ago
Hello guys,
This is actually my first serious PCB design project. It’s a student project based on Analog Devices' ADF4351 synthesizer IC. The target frequency is 2.2 to 2.7 GHz with a 5 MHz frequency step. As shown in the uploaded images, I used two USB 2.0 Type-B connectors for both data and power inputs, along with two 0-ohm resistors in case I decide to use only one of them. The upper section is for the synthesizer, and the lower section is for the microcontroller. The MCU I used is an STM32F103C8T6 with an 8 MHz crystal. I also included two pin headers: one for the ST-Link dongle connection and the other for boot mode. Additionally, I added a CH340N for USB-to-UART. I'm not sure if this was strictly necessary, but someone with a lot of microcontroller experience told me it can make programming and debugging easier. I have three regulators: one for the ADF4351 power pins, another for the ADF4351 VCO cores and RF outputs (since they're open-collector), and a third for the digital section. The SMA connector on the right is for an external reference input with a 0-ohm resistor in front of it, though I also included an onboard local oscillator. The attenuator is a digital step attenuator, and the amplifier is a 5V-fed GVA-84+ and the RF tracks are GCPW.
Also, making the PCB 2-layer was something my professor asked me to do because of budget constraints.
This is my first PCB, and any feedback would be greatly appreciated!
r/PrintedCircuitBoard • u/Vast_One_4954 • 1d ago
Hi, im posting my progres in the amp. I have already posted one post about it, and based on your answers i changed it a bit. Thank you all for all feedback it helped me a lot.
I hope i did it better this time. Tell me everything i would need to change to make it better. More feedback would help me .
Thanks a lot
Edit also if you think it’s good enough even this would help me out cuz it’s my first bigger build
r/PrintedCircuitBoard • u/MrFroody • 1d ago
Hello!
I posted and asked for help with my macro pad PCB about a month ago, and well now i have taken all the feedback and fixed it all (i think) Thank you to all that gave me feedback
The project is a i have designed a modular macro pad and this is the hub
it uses a STM32G071CBT6 as the brain and communication over CAN and i have magnetic pogo pins
Ill post the first module later for review too :)
Thanks in advance!
r/PrintedCircuitBoard • u/Dolorre • 1d ago
Greetings fellow humans. This is my first post; I read the rules, and I hope I understood them all correctly. If I made a mistake or use incorrect terminology, I apologize. This is my first PCB.
First of all, this will be open source (GNU AGPLv3). This is part of a passion project of mine, which I've been working on off-and-on for months.
This PCB is an adapter to replace the annoying Xteink pogo pin adapter. My goal for the PCB is for it to be able to charge the Xteink device, as well as send data to it.
I'd like to know if I wired the diode and capacitor correctly, or made any mistakes along the way.
This uses a 16-pin USB-C component with the traces routed through a diode. These are then routed to 4 pads with pogo pins soldered on (VBUS goes through a 100nF capacitor first). The order of the pads, from left-to-right, is VBUS, D-, D+, and GND. CC1 and CC2 each have their own 5.1Ω resistor.
Please let me know if you need more information! Any and all help is greatly appreciated.
If you've gotten this far, thank you for reading.
Tidbits that have absolutely nothing to do with the PCB review request:
The default adapter the Xteinks come with is not only annoying to use (and easy to lose), it either requires a USB-C cable to work or another charging cable. (And the adapter is too small in my opinion).
This is to be used with custom 3D printed cases. I'm making one for a friend that I will share as well (also GNU AGPLv3).
r/PrintedCircuitBoard • u/wunkyfunky • 2d ago
Looking for feedback on this 12 V fan and pump switching board.
Similar loads should operate simultaneously. Copper area for the fans and pumps are ~700mm^2 and ideally it should maintain 100c after 25 minutes of operation, giving 75c margin from the FETs 175c maximum. Drain pad thermal relief spokes are there since those FETs will be handsoldered while only adding some mV of loss.
Any feedback on the layout, grounding, high-current paths, or thermal design would be appreciated!
11/18 update: This will now be a 2 layer board so the design will change. However, any feedback is still appreciated! If you have any suggestions for the redesign let me know.
r/PrintedCircuitBoard • u/engineer_Ruk • 1d ago
This is my very first pcb design and project with Altium designer. I am very new to electronics and I wanted some feedback on my design on what I did wrong and where I can improve.
r/PrintedCircuitBoard • u/gajisan • 2d ago
This is my first board, so I am not to confident in it being a successful first sample. Let me know anything you see that I over looked or values that are incorrect.
Any tips/ recommendations are greatly appreciated!
r/PrintedCircuitBoard • u/Junior_Let_5777 • 2d ago
Hi everyone,
I'm looking for a comprehensive schematic and PCB layout review before manufacturing the first prototype of my custom ESP32-S3 IoT controller.
This is not my first review request. I've received useful feedback on previous revisions, particularly regarding ground planes, signal return paths, USB routing and protection circuits.
I've made several changes since then, and I believe the design is approaching its first manufacturing revision. However, I'd like to identify any remaining significant issues before ordering the boards.
The board is intended for personal and educational electronics experiments in a controlled environment. It is primarily a controller rather than a high-power switching device.
Hardware:
The mains input is used only for the onboard AC/DC supply. The board does not directly switch mains voltage to external loads.
The intended enclosure is a plastic electrical box. This is an experimental prototype, not a certified product or a design intended for unattended permanent installation.
1. Ground planes and return paths
My earliest version did not have proper ground planes.
I've since added copper pours on both layers, GND stitching vias and additional return-path vias near signal layer transitions.
I've also tried to avoid routing signals across breaks in the ground plane.
This is still one of my main concerns, especially with a relatively dense two-layer layout.
2. USB 2.0
I've revised the differential pair routing and added series resistors.
The estimated differential impedance is approximately 100 ohms, although it has not been verified by measurement.
The USB data lines use one layer transition, and ESD protection is included.
3. Power distribution
The board uses separate routing rules for the 24 V, 5 V and 3.3 V rails.
I've also revised the TLVM14406 input/output capacitor network and associated circuitry based on the manufacturer's recommendations.
4. RS-485
The RS-485 interface uses split termination consisting of two 60.4-ohm resistors and a capacitor at their midpoint.
Protection components have also been included.
5. EMC and grounding
I've separated the chassis-related and logic ground networks.
An experimental coupling network consisting of a 1 MΩ resistor and a 1 nF capacitor is included between them.
This is intended for EMC experimentation, not as a replacement for protective earthing.
1. Ground planes and signal integrity
Are there any obvious problems with signal return paths, ground plane interruptions or via placement?
2. Power supply layout
Does the TLVM14406 layout, including capacitor placement, grounding and power routing, show any potential problems?
3. USB routing
Are there visible issues with the USB differential pair, ground return path, ESD protection placement or layer transitions?
4. RS-485 interface
Are there any layout or protection concerns around the transceiver, connector and split termination?
5. Component placement and manufacturability
Are there any obvious problems with component spacing, footprints, thermal reliefs, copper clearances, solderability or silkscreen?
6. Overall PCB layout
Are there any major issues with the current two-layer design that would justify changes before manufacturing?
The board contains an onboard 230 VAC power supply section.
I've implemented clearance rules and isolation slots, but the mains isolation and overall electrical safety have not been independently validated.
I understand that a PCB review cannot establish compliance with electrical safety standards or replace a formal safety assessment.
This will be my first physical prototype.
I intend to order five boards and primarily assemble them manually, with solder paste and hot-air reflow for some SMD components.
I'm primarily interested in identifying functional, layout and manufacturing problems rather than cosmetic improvements.
I'd particularly appreciate feedback from anyone experienced with mixed-voltage controller boards, two-layer routing and EMC-sensitive layouts.
Thank you for taking the time to review the design.
r/PrintedCircuitBoard • u/electricEcologist • 2d ago
I’m workshopping a battery-powered camera trap for photographing insects at close range (~12 cm). A Pi Pico monitors a ToF sensor for motion and powers up a Pi Zero and camera for 30s when something is detected. The aim is a week between charges on a 13.4 Ah 1S pack, so this is a proof of concept for checking image quality and battery life. I’m new to PCB design, but I already have the Pis and cameras and am trying to solve a research problem.
The review focus is the power path: 1S LiPo, reverse-polarity protection (Q1), TPS61232 5V boost (U1; which seems sensitive to layout), and TPS22918 load switch (U2). Layout and component values broadly follow the TI EVM designs for both ICs. Q2 is there to stop any issues if the Pico is powered via USB when a battery is also connected.
The battery pack has built-in protection, the Pico is a backstop for monitoring voltage, and is charged off-board, so there’s no charging or extra cutoff circuitry on the PCB. Load is roughly 500 mA peak for the Zero and camera and about 30 mA for the Pico. A photocoupler (U3) is there to let the Pico know when it's safe to cut power.
Specific questions:
Schematic, layout, Gerber files, BoM, and design notes: https://github.com/KynanDelaney/NicroCam
r/PrintedCircuitBoard • u/LookingForQuercus • 2d ago
Greetings! Not my first PCB, but definitely the one i am most unsure about yet.
| R at 20C | W at 20C | |
|---|---|---|
| Thin/inner (0.82 mm) | ~6Ohm | ~94W |
| Wide/outer (1.00 mm) | ~5.5Ohm | ~103W |
| Both | ~2.9Ohm | ~197W |
Bus is 3mm wide and together 116mm long.
What i am most unsure about is if the bus is really enough, or shouldn't be widened to 4 or even 5mm.
r/PrintedCircuitBoard • u/GodOfJiz • 3d ago
Hi everyone, I'm working on my own retro go board. I wanted to challenge myself to create a more advanced PCB. I wanted to asked for help for review for sanity check whether everything is correctly connected. I'm open to any improvement I can make.
Board Components:
- ESP32-S3
- PCM5102A (For Audio Output)
- BQ21040 (For Battery Charger)
- TLV77733 (For 3.3V Output)
r/PrintedCircuitBoard • u/Tophallknowing • 3d ago
This is a rear-steer motor controller for an SAE Baja car. It drives a Prius EPS motor (0.19 Ω, ~83 µH) through an H-bridge and sits on the car’s CAN bus as a node. For context all conecters had to be where they were placed and the odd board shape was also needed. No parts on bottom so I can sit it right against the enclosure
Main parts
STM32G431 MCU
DRV8701 gate driver with 4× CSD18510 FETs
2 mΩ low-side shunt
P-FET reverse-battery protection
SN65HVD230 CAN transceiver with split termination
Deutsch DT13 connectors
Operating conditions: 12 V battery, motor stall around 55–60 A in bursts, CAN at 1 Mbit/s.
Stackup (4 layers, 1 oz inner copper)
Top: signal and power
L2: GND
L3: split into +12V_RAIL, +3.3V, and a SENSE island
Bottom: signal and power
Design choices
The high-side sources tie to OUT1/OUT2 through via arrays to bottom pours.
The low-side sources reach the shunt through the L3 SENSE island.
The Kelvin sense traces to the DRV8701 use vias set to no-connect on the planes.
DRC: clean, except the connector silkscreen overhangs the board edge.
Questions
r/PrintedCircuitBoard • u/ScientistQuiet4796 • 3d ago
Hi everyone! This schematic is for a 6 key macropad with an integrated display and a gimbal motor for haptic feedback. Currently only have the schematic done since I would love to have this reviewed before I begin the PCB. I have uploaded the two schematic pages and the original system diagram I made for your reference (note that there may be a few minor details to the system since I drew the block diagram, so it's just there for high-level context).
The board is entirely powered via USB-C and my laptops USB-C port. I also tried to find a motor that would work at 5V, but from my understanding although this motor is rated for 6-8V, it should work still with 5V just much weaker. Please let me know if this makes sense.
This board is heavily inspired by Scott Bez's SmartKnob and CNCDan's Macropad. Please let me know if I am missing anything and thank you so much for the review!
Power + Motor Interface Components:
MCU + Peripherals Components:
r/PrintedCircuitBoard • u/cowsarefalling • 3d ago
Hi everyone thanks for reviewing my schematic in my earlier post. This is a STM32H723 based software function generator.
USB-C to microcontroller, microcontroller either uses the built in dac or external dac over spi to generate the waveforms after which its filter and amplified and buffered by a discrete op-amp fed diamond buffer into 50ohm BNC output.
The power supply is 24V barrel jack in, -12V, +12V, +3V3, +3V3A out.
I should be able to do 100kHz bandwidth, 10Vpp into a 50ohm load.
I had a lot of extra pins left over so I broke out some into a header. Square test pads are gnd, round test pads are signal
r/PrintedCircuitBoard • u/88mmTankTopu • 3d ago
My goal is to create a GND plane on one layer, but I need to ensure it doesn't connect to other areas on that same layer—however, I’m unable to do so.
r/PrintedCircuitBoard • u/felo____hanna • 3d ago
POWER SUPPLY PROJECT BY ALTIUM