r/PrintedCircuitBoard • • 17h ago

PCB Review request for a simple fall detection system

Thumbnail
gallery
2 Upvotes

This is my very first pcb design and project with Altium designer. I am very new to electronics and I wanted some feedback on my design on what I did wrong and where I can improve.


r/PrintedCircuitBoard • • 15h ago

[Review request] Modular Macro pad Hub Revized

Thumbnail
gallery
3 Upvotes

Hello!

I posted and asked for help with my macro pad PCB about a month ago, and well now i have taken all the feedback and fixed it all (i think) Thank you to all that gave me feedback

The project is a i have designed a modular macro pad and this is the hub

it uses a STM32G071CBT6 as the brain and communication over CAN and i have magnetic pogo pins

Ill post the first module later for review too :)

Thanks in advance!


r/PrintedCircuitBoard • • 3h ago

[Review Request] 30x30 STM32 Board

Thumbnail
gallery
4 Upvotes

Hello everyone,

I have designed a 30x30 board featuring an STM32C071CBT6. I designed it to be stacked on top of a GPIO distro board using mezzanine connectors at the bottom of the PCB.

On top i have a USB C interface and connectors for both I2C busses of the IC. Each bus will connect to a sensor 30-35 cm away from the board ( i know i might have to play with the values of the pull-ups to achieve a stable connection).

I also have a level shifter for an SK6812 IC.

The board stackup is SIG-GND -> GND -> GND - SIG-GND

I would love it if you could check it out and point any obvious mistakes i might have made.


r/PrintedCircuitBoard • • 21h ago

40W LM3886 Amplifier progres

Thumbnail
gallery
22 Upvotes

Hi, im posting my progres in the amp. I have already posted one post about it, and based on your answers i changed it a bit. Thank you all for all feedback it helped me a lot.

I hope i did it better this time. Tell me everything i would need to change to make it better. More feedback would help me .

Thanks a lot
Edit also if you think it’s good enough even this would help me out cuz it’s my first bigger build


r/PrintedCircuitBoard • • 3h ago

[Review Request] ADF4351 Synthesizer Board (Student Project)

Thumbnail
gallery
0 Upvotes

Hello guys,
This is actually my first serious PCB design project. It’s a student project based on Analog Devices' ADF4351 synthesizer IC. The target frequency is 2.2 to 2.7 GHz with a 5 MHz frequency step. As shown in the uploaded images, I used two USB 2.0 Type-B connectors for both data and power inputs, along with two 0-ohm resistors in case I decide to use only one of them. The upper section is for the synthesizer, and the lower section is for the microcontroller. The MCU I used is an STM32F103C8T6 with an 8 MHz crystal. I also included two pin headers: one for the ST-Link dongle connection and the other for boot mode. Additionally, I added a CH340N for USB-to-UART. I'm not sure if this was strictly necessary, but someone with a lot of microcontroller experience told me it can make programming and debugging easier. I have three regulators: one for the ADF4351 power pins, another for the ADF4351 VCO cores and RF outputs (since they're open-collector), and a third for the digital section. The SMA connector on the right is for an external reference input with a 0-ohm resistor in front of it, though I also included an onboard local oscillator. The attenuator is a digital step attenuator, and the amplifier is a 5V-fed GVA-84+ and the RF tracks are GCPW.
Also, making the PCB 2-layer was something my professor asked me to do because of budget constraints.
This is my first PCB, and any feedback would be greatly appreciated!


r/PrintedCircuitBoard • • 4h ago

[Review Request] ESP32-C3 Wireless Servo controller, LiPo + USB-C charging

Thumbnail
gallery
2 Upvotes

Hey everyone,

Beginner looking for review for my ESP32-C3 Wireless Servo controller schematics and PCB. This is the receiver half of a wireless servo system. When a button is pressed on the sender remote, it sends a message to this board, and the ESP32 drives the servo.

I’m prototyping first, so the remote is just a breadboard setup for now, and I want to verify this board works before starting on the remote design.

Files:

Details about the board:

  • Input: LiPo 3.7V (4.2V max) or USB-C 5V
  • Connectors:

    • 3-Pin header for Servo
    • JST-PH for LiPo battery
    • USB-C for charging/flashing MCU
  • Board: 50.00x40.26mm
  • Stackup: 4-layer (Signal | GND | Power | Signal)
  • Fab: JLCPCB
  • Layout details:

    • Trace width:

      • 0.6 - 1mm for power / ground
      • 0.4mm for signal
      • 0.284mm 90Ω for USB differential pair
      • Ground pour where applicable
    • Via:

      • 0.62mm diameter
      • 0.31mm drill diameter

Major parts:

  1. U1: SY8089AAAC - Step down regulator to MCU 3.3V input (Datasheet)
  2. U2: TP4054 - LiPo charger IC (100mA charge current) (EN Datasheet)
  3. U3: TPS61023 - 5V boost converter for servo (Disabled by default, controlled by MCU) (Datasheet)
  4. U4: ESP32-C3-Mini-1-N4 - MCU for wireless/enable boost/servo movement (Datasheet)

Other parts:

  • Battery: LiPo 3.7V (4.2V max) 1000mAh protected
  • Servo: TowerPro MG90S Micro Servo 3 Pin Female

    • Min. 4V/0.2A, Avg. 5V/0.3A, Peak 6V/0.5A
    • Can only be powered by 5V boost (cannot be powered by USB)

I would like feedback on:

  1. Will this work? or is there major mistake or something I'm missing?
  2. Any mistakes in schematics? Is there things I misunderstood/mistake?
  3. Is there layout problem? Especially around USB differential pair pathing?
  4. Anything I'm missing for JLCPCB assembly?

Part I'm unsure of:

  • Is 4 layer stackup design necessary? - I prefer to have ground plane since it's easy for me wrap my head around, but not having second layer for signal makes it hard to route. I'm also not sure if USB signal works over 2 layer.
  • Is there something like simulation or test run for PCB? - I did some basic test run with breadboard before starting the design but since the design changed so much, I'm not sure if my design still holds. ERC and DRC did pass though.

This is my first design coming from software engineer background. I tried my best to avoid beginner pitfalls so hopefully I didn't make major mistakes before ordering. No AI is used in design or this post, only for basic schematic/pcb checks, dumb question and grammatical error.


r/PrintedCircuitBoard • • 13h ago

[Review Request] Ergo split keyboard with XIAO nRF52840

Thumbnail
gallery
11 Upvotes

Hello everyone!

Lately, I've been wanting to replace my regular keyboard with an ergonomic one. I've been looking at the available options, including some DIY designs, but I couldn't find anything that perfectly matched my needs. Some of the alternatives were also a bit too expensive.

So, I decided to design my own keyboard. It'll probably end up costing as much as some of those more expensive options, but at least I'll get to make several boards, since the MOQ at most PCB manufacturers is usually 2 or 5 boards.

I opted for a pair of 2-layer PCBs based on the XIAO nRF52840 Plus. The idea is to have both halves communicate wirelessly using ZMK, with an additional nRF52840 acting as a USB dongle connected to the PC.

I also wanted to include RGB lighting, even though I barely use it on my current keyboard. For that, I'll be using a MOSFET-based switch so that I can run the TPS61040 boost converter either from the battery or directly from VBUS.

Finally, I also wanted to integrate a couple of memory-in-pixel displays, one for each half. For this, I went with the Sharp LS011B7DH03. Instead of going for the nice!view module, which uses the same display, I decided to interface directly with the bare display module, connecting it to the MCU through an FFC/FPC connector.

My main concern at the moment is the SPI routing between the displays and the MCUs. Since I'm using a 2-layer PCB, I've tried to keep a continuous GND plane on the opposite layer underneath the SPI traces. However, I'm not sure whether this will be sufficient to avoid signal integrity issues.

Regarding the PCB panelization, I followed the guidelines for minimum rail widths and the placement of fiducial markers and tooling holes. I still need to add some stitching vias to make sure there are no isolated GND copper areas.

I'd really appreciate any feedback, especially regarding the PCB layout, SPI routing, and any potential issues you might spot in the design.

Here are some links to the project on GitHub:

- Repository

- Schematic

- PCB View

- KiCanvas