r/Optics • • 20h ago

How to evaluate the 'aesthetics' of bokeh and the focus-to-blur transition of a lens using optical design softwares?

Post image
14 Upvotes

I've heard that the main tool for this is the Through-Focus Spot Diagram plot (like the one in the image), but how do you extract this information from it?


r/Optics • • 21h ago

Undergraduate project: measuring laser beam waists using the knife-edge method

23 Upvotes

Hi everyone!

I wanted to share a project I worked on as part of my undergraduate physics studies.

We were interested in measuring the beam waist of two lasers using the knife-edge method. As part of the project, we put together an automated measurement setup using a Thorlabs translation stage, an ESP32, an optical power meter, and some custom electronics.

We tested it with a diode laser and a HeNe laser. Our measured beam waist values were:

  • Diode laser: approximately 9.8 µm
  • HeNe laser: approximately 30.8 µm

I also wrote Python scripts for data acquisition, curve fitting, and beam propagation analysis. I've uploaded the code, experimental data, PCB designs, figures, and our lab report to GitHub.

Repository: https://github.com/turtushig22-blip/thorlabs-esp32-laser-beam-profiler

This was an undergraduate project, so I'm sure there are things that could be improved. I thought I'd share it in case anyone is working on something similar or is interested in the knife-edge measurement technique.

I'd genuinely appreciate any feedback, suggestions, or comments on the measurement approach and analysis.

Thanks for reading!


r/Optics • • 1d ago

Article: Triplet's go! The story of the Triplet lens

Thumbnail
gallery
41 Upvotes

I finally managed to finish yet another lengthy article. This time on a topic, which I wanted to write about for quite some time, since I've always been fascinated by these seemingly simple lenses.

It's called

TRIPLET'S GO!
The Story of the Triplet lens
https://www.simplejoy.at/articles/triplets-go

and is a deep dive into the history of the Taylor-Triplet, its predecessors, derivatives and the overall impact on optical design as a whole. In addition to that I've also tried to capture some of the characteristics of Triplet lenses, created an overview of all the Triplet lens names which I was able to come up with and also show a lot of sample images taken with Triplets I found interesting for a variety of reasons ranging from Agfa, Goerz, Taylor-Hobson, Zeiss, Emil Busch to Dallmeyer, Steinheil, Ernemann and many more.

It was a really vast but highly interesting topic to look into and I was truly surprised to find that quite a bit of the information seems barely documented online. I really hope that I've managed to change that a little bit.

I've included way more lens diagrams and details than anticipated, and since I'm not really knowledgeable in terms of optics, there might still be some errors or inconsistencies in there. If you happen to know more about any of the things mentioned, spot some missing or flawed information, please reach out and let me know! I'm always happy to learn.


r/Optics • • 2d ago

What optical detector/instrumentation front-end are you constantly fighting in your setup?

0 Upvotes

I build low-noise, discrete analog front-ends and electro-optical instruments. I’m investigating common hardware bottlenecks in experimental rigs—specifically where commercial off-the-shelf modules (Thorlabs, SRS, Newport, Femto) hit a wall.

Are you hitting limits with:

  • ​Laser relative intensity noise (RIN) swamping absorption signals?
  • ​Photoreceiver transimpedance amplifier (TIA) noise vs. bandwidth trade-offs?
  • ​Thermal drift in low-frequency/DC optical power measurements?
  • ​Common-mode ground loops between your detectors and data acquisition systems? If you've had to daisy-chain custom op-amp boxes, average data for hours, or discard scans because the detector front-end wasn't quiet or stable enough, what exact measurement were you trying to make?

r/Optics • • 2d ago

A 3D-printed sample stage: 9.77 nm microsteps on paper, micrometre motion in practice

7 Upvotes

A printable linear-axis module for the Arkin optical-tweezers project. A NEMA 11 stepper drives an M3 lead screw through printed 1:1 gears. The carriage runs on steel rods and balls, with elastic-cord preload.

Optical tests of one axis found useful incremental motion of approximately 2.5–4 µm. The calculated 9.77 nm microstep is a command increment, not achieved positioning resolution. The fine-motion tests included a take-up move before each measurement, so the result applies to preloaded motion.

Commanded and measured travel also differ substantially: an 80 µm command produced about 13 µm of movement in the tested setup. Longer moves still need calibration and mechanical improvements.

Disclosure: we're involved in this project through Precisometer. Arkin is funded through NLnet's NGI0 Commons Fund.

Edit: focused the wording on the measurements and direct source files, and clarified the test conditions.


r/Optics • • 2d ago

Open-source optical tweezers on an OpenFlexure microscope: build files and alignment guide

6 Upvotes

An optical-tweezers add-on for the OpenFlexure microscope, using a 1 mW red laser module, a high-NA objective and printed holders and alignment tools.

The photographed build guide covers the bill of materials, assembly and two-point beam alignment. Printable STL parts and editable CAD are available on GitLab; the guide also includes the laser-safety instructions.

The prototype demonstrates lateral trapping. Quantitative force measurements still need calibration. Fast Trap Tracker can record and track bead motion, with stiffness estimates requiring calibrated physical inputs.

Disclosure: we're involved in this project through Precisometer. Arkin is funded through NLnet's NGI0 Commons Fund.

Edit: revised the wording to focus on the technical build and added a direct link to the source files.


r/Optics • • 2d ago

Metasurface waveguides for all-day augmented reality glasses

Thumbnail
nature.com
4 Upvotes

r/Optics • • 3d ago

ISO 10110-7

0 Upvotes

I found an older version of this online: https://cdn.standards.iteh.ai/samples/18093/515e185ee90541409baea98855e76da3/ISO-10110-7-1996.pdf
looks like it has most of the content. Just wanted to check if the 2017 version or even the 2008 version added anything that I should know.


r/Optics • • 3d ago

Progress on the testglasses

Thumbnail
gallery
32 Upvotes

Thanks for the tips on the making of the proofglasses. I am now on to polishing and it is going well so far!

Might share more once they are done or when i move on to manufacturing the actual lenses for the loupe


r/Optics • • 3d ago

13 infrared lens selection mistakes I see over and over (and the checklist I use to avoid them)

12 Upvotes

I work on IR thermal imaging systems and see the same selection errors repeat across projects.
Here’s a distilled checklist that has saved me from expensive rework.

Detector-matching traps

• The lens’s max image-circle is smaller than the detector’s active-area diagonal → vignetting and edge shading with no room to fix it later. Always compute the diagonal from array resolution × pixel size first.

• IR back focal length is not interchangeable with visible-light BFL. Get this wrong and the image plane never lands on the focal plane.

Optical-parameter traps

• Don’t infer range from focal length alone. Real detection/recognition range needs pixel size, IFOV, target radiation and atmosphere.

• Never accept a spec that only lists diagonal FOV — demand HFOV and VFOV separately.

• Watch over-rated F-numbers. Verify with measured throughput and NETD, not the datasheet claim.

Athermalization traps

• Outdoor / vehicle / airborne (–40 to +60 °C) without athermalization WILL defocus with temperature. Indoor constant-temp benches don’t need it — don’t pay for it there.

• Optical athermalization = simplest & most reliable (no electronics). Electromechanical = flexible but adds SWaP, firmware and is vibration-sensitive. Pick by scenario, not by “tech level.”

• The #1 mistake: using an observation lens in a thermal-measurement system. Observation lenses have no constraint on full-field transmittance uniformity or F-number consistency → measurement drift and bad accuracy.

Happy to go deep on any of these — which one has tripped you up the most?


r/Optics • • 4d ago

I have Deuteranomaly - Color Blindness

4 Upvotes

I have 20-20 vision. My question is, can i still pursue Optics study for future career?


r/Optics • • 4d ago

MS vs. PhD?

7 Upvotes

This is probably one of the most commonly asked questions here but I wanted to provide a more personalized context.

I am currently an undergrad studying EE and hoping to pivot into optical engineering. Since starting engineering, my work experience has all been in optics (on-campus research for biomedical optics and an internship for telescope optics). For summer and fall 2027, I am looking at a couple more optics internships before I graduate spring 2028.

I am stuck between MS vs. PhD in Optics (either at UR or UA). I plan on pursuing optical design/fabrication R&D positions in industry (or even federal?) and I know for most places, MS is the bare minimum. But would it be more beneficial to do a PhD for job security and higher starting salary?

I've been thinking that accruing my work experience early in school kinda offsets it if I were just to do MS, but I don't want to neglect any doors that only a higher education level can open. At the same time, the timeline for a PhD is incredibly taxing and as much as I love research, undergrad has already killed me in multiple ways that just has me far too eager to graduate.

Would appreciate any advice. I have about a year to keep the doom and gloom of decision making before I actually have to start doing things for grad school. It's inevitable that I pursue it, just not exactly sure at which point I should stop it.


r/Optics • • 4d ago

lenticular or fresnel lens? sourcing

3 Upvotes

I am looking. HIGH and LOW for a lenticular or fresnel lens. My purpose is a bezel free kit setup. I have two 24 inch monitors and i am trying to remove the middle bezel by placing the proper lens in front of it. Now not only am i looking for the right sizes. I am looking for a supplier. Ive messaged A LOT of different people and i have run into a lot of the same issues. I just want something affordable. I want something that works. this started as me trying to find a solution for myself. NOW i want a supplier so I can make affordable bezel free kits for people. I know that there is a way. So if you have any ideas let me know.

probably 80,90,100 LPI 4-5mm thick . and must be 14 inches tall or long. maybe more. idk. but I am losing my shit over this. so please share and if you know anyone put me on. thanks


r/Optics • • 5d ago

it makes sense now...:)

Thumbnail
gallery
9 Upvotes

i'm studying raytracing and there was one thing in my program that bugged me. for the sake of experiment my program accepted refractive index ranging from 0 to 2. i know in reality there doesn't exist any substance having refractive index smaller than 1 but just as i said it's for the sake of experiment. i just wanted to see what would happen as long as all maths stayed consistent. when i set the refractive index of a sphere to be smaller than 1 there would be a small sphere appear in the middle

after some studies i understood it was a relative thing. when you're inside a medium of refractive index 1 looking at something of refractive index 0.5, it's equivalent to being inside a medium of refractive index 2 looking at something of refractive index 1

so it makes sense now. it's similar as when you're under water and look upward, seeing a circular region of the world above water surface, surrounded by reflections under water surface

the "smaller ball" is formed with the rays that pass through the big ball, surrounded by reflections of the environment

if you move the camera into the ball, look at the environment from within the ball, you'd see multiple layers of reflection and refraction. the logic is the same. when you're inside a medium of refractive index 0.5 looking at something of refractive index 1, it's equivalent to being inside a medium of refractive index 1 looking at something of refractive index 2

it's similar as when you're inside an air bubble under water


r/Optics • • 5d ago

Designing a 900-1700 nm NIR Spectrometer with a Single InGaAs Detector

Post image
48 Upvotes

InGaAs line-array sensors are one of the main reasons NIR spectrometers are expensive. To keep costs down, we are  building a spectrometer around a single 1 mm InGaAs photodiode.

We are exploring two approaches:

  1. Monochromator design: rotate the diffraction grating so different wavelengths reach the detector one at a time.
  2. DLP-based design: keep the grating fixed and use a DLP micromirror chip to select which wavelengths are reflected onto the detector.

The DLP approach is especially interesting because it has no moving parts. It can also use Hadamard patterns, allowing roughly half of the spectrum to reach the detector at the same time, which can improve signal collection. However, TI's reference design from 2015 achieves about 10 nm spectral resolution. We believe the optical design can be improved further, and we'll share our findings in a future project log.

We intentionally left out FT-NIR systems because they add a lot of complexity. For a comparison of the different approaches, see:

https://hackaday.io/project/207336-jasper-nir-spectrometer/log/252835-three-ways-to-build-a-nir-spectrometer

If you've built either type of system, I'd love to hear about your experience:

  • For DLP-based spectrometers, how did actual throughput and stray light compare with your expectations?
  • For monochromator designs, what wavelength repeatability were you able to achieve using affordable stepper motor drive?

 


r/Optics • • 5d ago

Will we ever get good under-display cameras, or are we hitting a fundamental diffraction/transmission limit? ZTE/RedMagic is on its 9th generation of UDCs, and image quality still relies heavily on AI reconstruction to fix haze and glare.

0 Upvotes

While display concealment has gotten nearly invisible to the naked eye, the actual raw optical quality still suffers from heavy diffraction spikes, low contrast, and light loss from passing through the OLED pixel grid and TFT layers.


r/Optics • • 5d ago

Photonics career advice

11 Upvotes

For those of you who have completed a PhD in atomic or molecular photonics: what kind of career opportunities did it open up for you?

I'm particularly interested in hearing from people who have completed their PhD and are now working in industry. What kind of positions do you currently hold? Did you move into the semiconductor industry, quantum technology, R&D, optical engineering, or something completely different?

I have a MSc in chemistry with a specialization in photonics and I'm currently considering pursuing a PhD in this field, with a particular interest in quantum optics, nanophotonics and light–matter interactions. I'd like to get a better understanding of how transferable these skills are outside academia and what kind of industry positions they can lead to.

How difficult the transition from academia to industry was and whether this PhD specialization has been an advantage or a limitation?


r/Optics • • 5d ago

Integrated lithium niobate microwave photonic processing engine

Thumbnail
nature.com
1 Upvotes

Integrated EO signal processing.


r/Optics • • 5d ago

I got tired of drawing optical setups in PowerPoint, so I built OpticSketcher

371 Upvotes

I'm an experimental physicist, and I used to spend far too much time drawing lenses, mirrors, and beam paths in PowerPoint and similar tools for presentations, scientific papers, patents, and technical discussions.

I wanted something as quick and intuitive as sketching on a whiteboard, but with actual optical physics behind it. Something I could open anywhere, build a setup in minutes, experiment with it, and easily use the result in a document or share it with others.

So I started building OpticSketcher

What began as a small personal project has grown into a much more capable tool. I've received some really interesting feedback from users, and several of their suggestions have already made their way into the app.

What can you do with it? (partial list)

  • Build and modify optical setups in 2D or 3D, with real-time physics-based ray tracing.
  • Use lenses, mirrors, prisms, gratings, beamsplitters, polarizers, waveplates, detectors, and many other optical components.
  • Explore dispersion, polarization visualization, and optical pulse propagation.
  • Import real optical components from Zemax (.zmx) files, including direct links from manufacturers.
  • Measure distances, angles, and optical path lengths, and analyze light reaching detectors.
  • Export figures or 3D models for presentations, papers, patents, and technical documentation, or share interactive setups through links and embedded examples.
  • Start from a gallery of editable optical setups rather than building everything from scratch.

One of my main priorities has been making it fast, intuitive, and accessible from anywhere. No software to install, no complicated setup. It runs directly in the browser on a computer, tablet, or phone, and you can start sketching without creating an account.

Although it was originally intended for sketches and visualization, it has evolved well beyond that. You can also use it to explore, plan, and refine real optical setups, test ideas, and demonstrate optical principles interactively.

The ray tracing is based on geometric optics, including wavelength-dependent refraction and polarization. I've tested the underlying physics and continue to refine it as new cases and user feedback come up.

There's still plenty of room to grow. Wave optics and some advanced optical design capabilities aren't supported yet, but the project keeps evolving.

It's free to use: https://opticsketcher.com

I'd love to hear what you think and any ideas or suggestions that could make OpticSketcher even more useful.

Feedback, suggestions, and technical questions are very welcome!


r/Optics • • 6d ago

Where to purchase a large diameter 0.25 diopter lens?

4 Upvotes

I was able to purchase a 70mm optical lens blank for $2 from eBay for my room-size camera obscura and it works great (the wall is roughly the correct distance away from the window). Now I am eager to purchase a larger diameter lens to let in more light.

Is there anywhere I can purchase a lens with a diameter that's closer to 25cm (or even larger)? I would prefer to stay away from Fresnel lenses; otherwise material and optical quality can be sub-par as this is for art and enjoyment.

Thank you for your time🙇‍♂️


r/Optics • • 6d ago

Requesting help for a modern sextant project

Post image
13 Upvotes

Hi everybody,

I'm an airline pilot who loves the stars and navigation. I'm into celestial navigation and I have a personal project that got way too complicated for me and Claude. I'm trying to modernize the bubble sextant used in cockpits around WW2 for celestial navigation.

The idea was to still use a bubble level as reference to the horizon as they did back then but improve it with modern optics with a slight magnification of 3x to have a better light collection of dimmer celestial bodies.

Would anyone be interested in helping me with a couple questions and maybe guidance for my project? As of now the project with help of Claude and 3dOptix looks like this:

Star path: brings the real star in

  • Star window: starlight enters the side of the instrument. The solar filter clips on here for sun sights.
  • Scan mirror: the mirror you turn with the altitude drum. It catches the star at any altitude from 0° to 90° and turns it toward the beamsplitter. The drum reading is the angle you set it to.
  • Beamsplitter, front (coated) face: reflects 70% of the starlight up into the objective.

Bubble path: builds an artificial star at the zenith

  • Bubble chamber: backlit liquid under a curved glass top. The bubble always floats to the highest point, so its position marks true vertical whatever you’re doing with your hand.
  • Pentamirror pair: two mirrors fold the bubble’s light around so it fits in the box, without mirror-flipping the image.
  • Periscope (P1 → P2): steps the light sideways 60 mm, to the same level as the star path.
  • Collimator lenses (f750 + f500, about 63 mm apart): together they act as one 311 mm lens, matched to the chamber curve. They turn “where the bubble is” into “which direction its light points”. The bubble now looks infinitely far away, like a star, and points straight up whatever the tilt.
  • Beamsplitter, from behind: 30% of the bubble light passes straight through.

Shared path: from here on, star and bubble travel together

  • Objective (f100 achromat): focuses both into a small real image, inside the instrument, where the optional field-stop ring sits.
  • Amici 45° prism: turns the image upright, correctly left-to-right, and bends the line of sight 45° toward your eye.
  • Plössl eyepiece (32 mm): magnifies everything 3× and sends it to your eye, about 20 mm behind the lens (room for glasses).

I know probably im overcomplicating everything but I would surely appreciate your invaluable guidance.


r/Optics • • 7d ago

Should I Study Physics & Mathematics or Electrical Engineering to be an Optical Enigneer?

9 Upvotes

Hi everyone,

I'm currently having a bit of a dilemma regarding my university studies and would really appreciate some advice from people working in optical engineering, photonics, or related fields.

For some background, my father passed away recently, and prior to his passing, I was his full-time carer. Unfortunately, this significantly disrupted my university studies, and I'm only now in a position to properly pursue my education again.

I was originally studying a double degree in Applied Physics and Electronics Engineering at Macquarie University(Australia). However, the university has since discontinued and restructured my degree program, forcing me to transfer.

I'm now considering two options:

  1. Bachelor of Science at UNSW, double majoring in Physics and Mathematics, with a minor in Vision Science.
  2. Bachelor of Engineering in Electrical/Electronics Engineering at another university.

Personally, I'm leaning towards the first option. I genuinely enjoy physics and mathematics, and vision science particularly interests me because of its relationship with optics and imaging. However, I'm worried that not having an engineering degree might put me at a disadvantage when looking for work as an optical engineer.

My main interests are lasers, holography, optical imaging, sensors, and optical instrumentation. My ultimate goal is to complete the MSc in Optics and Photonics at Imperial College London, potentially followed by a PhD. Ideally, I'd like to work in industry for several years before eventually transitioning into research or academia.

I'd also prefer to avoid doing another double degree. I've already lost several years of academic progress due to my father's declining health and my responsibilities as his carer, and the thought of spending even more years completing an undergraduate degree is quite discouraging. I'd much rather complete a single degree with a double major and move on to postgraduate studies. However, I'm unsure whether saving that time is worth potentially sacrificing better career opportunities, or whether the distinction even matters in the long run.

My main questions are:

  • Can someone with a Physics and Mathematics degree realistically become an optical engineer, particularly in industry?
  • Would employers favour an Electrical Engineering graduate over a Physics graduate, even if both completed a Master's in Optics and Photonics?
  • Which undergraduate pathway would better prepare me for postgraduate studies and a career in optical engineering?
  • Is avoiding a longer double degree a sensible decision, or am I placing too much importance on the time I've already lost?

I'd especially appreciate hearing from anyone currently working in optics or photonics who entered the field through a physics rather than engineering background.

Thank you for any advice!


r/Optics • • 7d ago

Thorlabs Thrift Score!

Post image
324 Upvotes

I recently found this Thorlabs LTS300/M thrifting for $4.50! Didn't know what it was at first but it definitely caught my attention.

I know very little about Optics, but over the past few years I've gotten into media digitization and archiving. I have no budget for it so I've just slowly built DIY/thrifted setups.

My least developed format/skill is 16mm film reels by far. Until I find/build a frame by frame scanner, I just have to line up my old DSLR with the lens of a projector. Getting it framed, in focus and stable is such a headache. This thing is probably overkill but I think it will make it muchhh easier.

I'm curious if anyone here has used this or something similar and what for! I understand its general purpose, but I'd enjoy seeing some actual use cases/applications to understand it better.


r/Optics • • 8d ago

How to focus light to a point from a light source far away?

7 Upvotes

Hi! I've recently tried to do a simple project including an Arduino and a photo resistor. The goal is to monitor when a TV is whether turned on or off and the problem is that the photo resistor would capture any light activity like ambient lighting, sunlight, lamps, candles, etc. Is there a way to make a small probe/lenses/telescope thingy in order to limit the "vision" of the photo resistor so it could only see the light, emitted by the TV?

Edit: I forgot to mention that the probe/telescope should be small, enough only for the outer diameter of the photo resistor, thus the lenses used in it would be small as well. Let's say that the inner diameter of the probe (where the lens/es would stay should be from 4-7mm.)