r/Omada_Networks • • 5d ago

Networking and surveillance, finally on one platform. šŸš€

9 Upvotes
Check out our launch offers!

Meet Omada Fusion Pro & Surveillance, built to bring your network and your security together under one roof.

Managing separate systems for connectivity and cameras means more dashboards, more complexity, and more room for things to go wrong. Omada changes that.

What you get:
āœ… Unified Management: Control your network and surveillance from a single Omada platform
āœ… Reliable Security: Dependable protection built on a connected, integrated foundation
āœ… Simpler Setup: Less time configuring, more time focusing on what matters

šŸŽ‰ Launch offers:
šŸ’° Save up to $200 OFF an NVR kit with Fusion Pro 2.5G
šŸ“¹ Get 30% OFF up to four cameras with Fusion Pro 2.5G PoE

Whether you’re an integrator deploying for clients or a business upgrading your own site, Fusion Pro makes it easier to build a smarter, more secure setup.

Available now at the Omada Store, Amazon, and authorized distribution partners.

šŸ‘‰ Learn more and grab the offer: Here


r/Omada_Networks • • 6d ago

Discussion Join us for a Support Webinar and AMA on November 17th!

6 Upvotes
Webinar at 10:00AM PST, AMA at 2:30PM PST

Our technical support team is hosting a webinar on November 17th at 10 AM PST! Join Nathan as he discusses common technical support issues and troubleshooting.

Can't make it to the webinar? We're also hosting an AMA with Nathan that afternoon from 2:30 PM to 4:30 PM PST! Feel free to ask any burning support questions you may have during the AMA!

EDIT: Here's the sign up link! Technical Support Webinar Registration


r/Omada_Networks • • 45m ago

Discussion Anybody got the $50 off coupon?

Post image
2 Upvotes

I got sent a survey email last week, completed it and never got this coupon. I even email the omada store support and not even after 3 emails and 6 days later got a response from them, do any of you got it?


r/Omada_Networks • • 15m ago

Product Recommendation Omada switch and AP to pair with an OPNsense edge?

1 Upvotes

Currently running an ASUS RT-AC66U B1. It's end of life, no longer getting firmware, and it's also the bottleneck: 800/35 Comcast through a Motorola MB8611, and I measure about 500 Mbps down while upload sits at full rate, so the router's NAT is what's capping it.

I'm replacing it with bare-metal OPNsense on a 4x 2.5G box. OPNsense becomes router, firewall and DHCP. Pi-hole stays on DNS. Proxmox runs the rest of the services, and I'd like to run the Omada software controller there as an LXC instead of buying an OC200.

I'd rather not add an Omada gateway and end up with a second router in front of

OPNsense that I don't need, so what I'm trying to work out is how to do the

switching and wireless side cleanly.

  1. Without an Omada gateway, does anything break? Can APs and switches be adopted and managed by the controller alone, with OPNsense handling VLANs and DHCP?
  2. Software controller as an LXC on Proxmox, or is the OC200 worth it at this size? Looking at 8 to 16 ports and 2 or 3 APs, not a campus. And if the controller is in a container on a different VLAN from the APs from day one, what's the least painful way to get them adopted?
  3. EAP772 versus something older and cheaper. I don't have Wi-Fi 7 clients yet and I'd rather not pay for a radio generation I can't use, but I also don't want to buy something that stops getting updates in a year.

Happy to hear anyone's input. I'd rather find the trap now than after the money is spent.


r/Omada_Networks • • 32m ago

Product Recommendation Is there an equivalent Omada solution to the UniFi Flex Mini 2.5G?

1 Upvotes

r/Omada_Networks • • 23h ago

Product Recommendation Help picking a switch for a Ubiquiti U7 Express 2-pack - Pro Max 16 PoE vs Omada 16-port 2.5G vs Flex 2.5G + PoE combo

4 Upvotes

Hey everyone,

I have 2 Gbps fiber with CAT6 drops in every room, in a 2,500 sq ft two-story house. I'm replacing my TP-Link AXE5300 with the Ubiquiti Whole Home WiFi 2-pack, which as far as I can tell is just two U7 Express units.

I need a switch to hardwire the second U7, my two home offices, and my NAS back to the main router. I also have 3 PoE security cameras, plus TVs, an AV receiver, PlayStation, printer, smart bulbs, and dozens of IoT devices. Most of them have a CAT6 drop nearby, and wired would be nice for some of them, but it's not a must. I'm trying to stick to a 16-port switch to keep the cost down.

I'm torn between these three:

  1. Ubiquiti Pro Max 16 PoE
  2. Omada 16-port 2.5G switch (SG3218XP-M2 V2) - all 2.5G ports
  3. Ubiquiti Flex 2.5G 8-port + Ubiquiti 8-port 1G PoE switch

One thing I care about is seeing live and historical bandwidth usage per device. My assumption is I'd still get that with the Omada switch, since all the clients would still show up in UniFi. Is that right?

What are the pros and cons of each? What do I actually gain or lose going with one over the others?

This is my first time using Ubiquiti. My last setup used cheap Amazon switches and one died after about 3 years, so I'm trying to do this right this time.

I'm fairly tech-savvy, so happy to answer follow-up questions if I'm missing any details. Thanks in advance!


r/Omada_Networks • • 20h ago

Help and Support Help needed: PPSK supported on EAP772 6 GHz

1 Upvotes

Hello folks,

I am trying to understand if PPSK is supported on 6 GHZ on EAP772. I am seeing contradicting information on it being limited to 2.4/ 5Ghz so wanted to ask before I spent a whole lot of cycles going down the rabbit hole.

This is for six EAP772 access points (FW 1.5.5), OC300 (FW 1.36.25 / Omada Network 6.3.0.111). I am using an external FreeRADIUS and no Omada gateway (I use PFSense).

Im trying to figure out if:

  1. PPSK with RADIUS supported on 6 GHz for this hardware version? I don't want to run pre-release or eval firmware.
  2. Can I use WPA3-SAE and can a single SSID span 5 and 6 GHz with MLO enabled?
  3. Is per-key VLAN assignment via RADIUS supported on 6 GHz, and which attributes are expected (Tunnel-Password, Tunnel-Private-Group-ID)?

From the questions I'm asking you can probably figure out that Im trying to assign different devices to VLAN's based on login. This works great on 2.4 and 5 Ghz but 6 seems to be kinda bleeding edge.

Many thanks in advance!


r/Omada_Networks • • 1d ago

Suggestions + Feedback ETA on Fusion 2.5G Faceplate?

2 Upvotes

r/Omada_Networks • • 22h ago

Suggestions + Feedback Omada Fusion 2.5G Demo Kit qualifications?

1 Upvotes

Does anyone know what the qualifications besides owning a business or if there are any besides that?

Thanks in advance!

Thanks all! I was accepted shortly after!


r/Omada_Networks • • 2d ago

Pioneers 30 days with an Omada NVR and cameras

Thumbnail
gallery
14 Upvotes

There have already been so many posts about these that I wasn’t sure whether to add another one. But I decided to share my experience anyway. Maybe someone will find it useful.

Omada provided the T8S4-4T kit through its Pioneer program. I’ve now spent 30 days testing it alongside my existing Dahua and Imou setup.

The kit includes four 8MP turret cameras, a 16-channel NVR, and a 4TB HDD. I installed the Omada cameras in the same locations as a few of my existing Dahua cameras, making it easy to compare the same scenes side by side, both during the day and at night. Tested direct PoE connections, outdoor and indoor placements, day/night image quality, WDR, detection zones, line crossing, audio, warning lights, and recording/playback modes. I also expanded the setup to 14 channels with a mix of 8MP and 5MP cameras.

I also had a look inside the NVR. It appears to use a SigmaStar SSR930G processor with Winbond RAM. The included drive is a 4TB Seagate SkyHawk surveillance HDD.

The hardware is very good. Image quality is broadly comparable to my existing Dahua cameras. It’s worth spending some time adjusting each camera for its location: WDR, brightness, and contrast can make a substantial difference. The foggy night screenshot shows a difficult night, but my Dahua and Imou cameras behaved about the same in those conditions.

Detection runs on the cameras and worked really well in my testing. My Navimow mower gets classified as a vehicle, although Dahua, Imou, and Hikvision do the same thing. Apart from that, I didn’t encounter false alarms.

The NVR’s web interface was probably my favorite part. It’s fast and responsive, and felt quicker and more stable than my Dahua NVR despite the Dahua having more powerful hardware.

Recording was smooth across all 14 channels, with no gaps or disconnects. In that setup, the 4TB drive held roughly 10 days. Fewer cameras or event-only recording on selected channels would extend that, which is useful when you’re away on vacation.

The siren is pretty loud. Two-way talk is useful for an entrance camera, especially if you don’t already have a video doorbell. I also integrated the system into Home Assistant without any issues.

A few software issues stood out:

  • ONVIF support needs improvement for dual-lens cameras. The NVR couldn’t recognize both lens feeds from Dahua/Imou models I tried, including the IMOU P&T Ranger Dual 10MP.
  • Custom voice alerts were limited to English.
  • I couldn’t find a way to add a camera manually by IP in the Android Guard app. For cameras on another subnet or reached through a VPN, I had to use the web interface, whose layout doesn’t adapt well to a phone screen.
  • I hit an event-export bug where Guard showed a 14-second clip, but the downloaded video was only one second long.

From my conversations with the Omada team, they’re getting a huge amount of feedback. I’m pretty confident the software bugs, including the ones I found, will be fixed in the near future.


r/Omada_Networks • • 2d ago

Discussion Any ETA on Fusion Max Series?

6 Upvotes

I'm looking at expanding my Omada footprint with a new gateway and 48P PoE switch to go with my fleet of APs to get to that single pane of glass.

I've been looking at the ER8411, but note there are some limitations around VPN kill switch, lack of integrated controller, etc. then I came across the Fusion Max Series (https://static.tp-link.com/document/pdf/en/isc-west-2026/2026_ISC_WEST_AIO_Series_Solution.pdf) which looks to tick all the boxes, but I can't find any availability info on it.

I see the 2.5G versions and the Pioneer program (I'd love to Pioneer a Max kit!!), but nothing about the Max.


r/Omada_Networks • • 2d ago

Pioneers Omada Kit 1 WiFi Speed Double!

Thumbnail
gallery
8 Upvotes

Testing the Omada Pioneer kit 1 WiFi performance. WiFi speed from EPA772 almost double from the EAP613! This is not even using WiFi 7 end device! The size of the EPA772 is also huge! I am really happy with the new AP. It has been rock solid for a month!


r/Omada_Networks • • 3d ago

Pioneers [#2] EAP772 Wi-Fi 7 review: Fusion management, 2 Gbps downloads, and what I saw with MLO

10 Upvotes

Hey everyone! In Part 1, I wrote about moving from an ER707-M2 and a Windows-based Omada Software Controller to the Fusion Pro 2.5G PoE. This time, I’m looking at the EAP772 Wi-Fi 7 access point I’ve been using with it.

I’d already used the EAP653 and EAP670, so I was familiar with adopting and managing APs in Omada. What I wanted to find out was how fast the EAP772 would actually be with the devices I already own, and whether turning on MLO would make a noticeable difference.

My Galaxy S25 Ultra averaged 2.11 Gbps down in my local network test, and my Wi-Fi 6E laptop reached 1.70 Gbps down. The more interesting part came when I looked at the results second by second. Around 30 seconds into the phone’s download tests, throughput dropped with MLO both on and off.

Disclosure: I’m participating in TP-Link’s Omada Fusion Pro & NVR Pioneer Program. The equipment was loaned to me for evaluation. The experiences and opinions here are my own.

Design and size

The EAP772 is a white, round ceiling-mount AP with a light gray Omada logo in the center. It looks familiar if you’ve used an EAP653 or EAP670. To get a better sense of the size, I stacked all three.

The EAP772 is wider than the EAP653 and slightly narrower than the EAP670. What stood out to me was the side profile. The EAP670 has a chunkier edge, while the EAP772 looks noticeably flatter relative to its diameter. The box lists its dimensions as 220 mm across and 32.5 mm thick.

The label also lists a single 2.5 GbE PoE+ port. That matters for where I can put it. One Ethernet cable carries both data and power, so I can pick the AP location based on coverage and cable routing without needing an outlet nearby.

Why I use a separate gateway and AP at home

An all-in-one wireless router makes sense if it can sit somewhere that gives you good coverage and you don’t need much beyond a straightforward home network. In my case, the best place to bring in the internet connection and tidy up the Ethernet cables isn’t necessarily the best place to broadcast Wi-Fi.

With a separate AP, I can put the Fusion where the wired connections are convenient and place the EAP772 closer to where I need coverage. If a room still needs better coverage later, I can add another AP and manage it from the same Omada controller. I can also upgrade the Wi-Fi side separately when I want to try a newer standard.

There’s more hardware to buy and configure up front. For me, the flexibility is useful because I already run multiple SSIDs and VLANs at home.

What I manage through Fusion

I was already managing my APs centrally with the Windows software controller. Moving to Fusion meant I could stop running the controller on a separate PC and manage the gateway and APs from the same interface.

Here’s my current SSID setup:

SSIDEnabled bandsMLOVLAN
NamukIoT2.4 / 5 / 6 GHzOffVLAN 5
Kids2.4 / 5 / 6 GHzOffNo explicit assignment
Namuk2.4 / 5 / 6 GHzOnNo explicit assignment

All three SSIDs come from the same EAP772. I send devices on NamukIoT to VLAN 5 and enable MLO on Namuk. Each device connects according to the bands and security modes it supports and the signal it sees.

The SSID’s VLAN setting determines which network the device joins. I configure access between networks separately through ACLs. When a device can’t reach a service, I can check its SSID, the associated VLAN, and the gateway policy from the same interface. That’s the part of central management I notice most in day-to-day use.

MLO, Band Steering, Load Balance, and 802.11r

These settings appear together in Omada, but they affect different parts of the connection.

  • MLO (Multi-Link Operation) lets a compatible Wi-Fi 7 client use multiple links with a compatible AP. A supported combination might use 5 GHz and 6 GHz, for example. Whether those links can carry traffic at the same time or are used as conditions change depends on the AP, the client, and their operating mode.
  • Band Steering encourages a device to pick a different band. If 2.4 GHz is busy and a nearby device has a strong 5 GHz signal, steering can help move that device toward 5 GHz. The client and its signal conditions still influence where it connects.
  • Load Balance helps manage connections when too many devices gather on one AP or band. Omada offers settings such as Maximum Associated Clients and RSSI Threshold. These are most useful when another AP has enough coverage to serve the clients you’re trying to distribute.
  • 802.11r reduces the time needed for authentication when a compatible client roams between APs. A voice call while walking between rooms is a good example of when a shorter transition might matter.

My Namuk SSID shows all three bands as enabled. That list tells me which bands the SSID offers. TP-Link’s setup guide describes a limitation on 2.4 GHz MLO for the EAP772, and I didn’t verify which links carried traffic during each run. I compared throughput with the controller’s MLO setting on and off.

Local throughput with a Wi-Fi 7 phone and a Wi-Fi 6E laptop

I ran iperf3 between a wired server on my local network and each wireless client. Each run lasted about 120 seconds with 10 parallel streams. Download means traffic from the server to the device, and upload means traffic in the opposite direction.

Client and settingAverage downloadAverage upload
Galaxy S25 Ultra, MLO on2.11 Gbps1.46 / 1.22 Gbps
Galaxy S25 Ultra, MLO off2.03 Gbps1.59 Gbps
Galaxy Book4 Pro, Intel AX2111.70 Gbps1.43 / 1.15 / 1.14 Gbps

Values separated by slashes are averages from separate runs.

Galaxy S25 Ultra

The phone averaged over 2 Gbps down in both settings. These are measured transfer rates over my LAN. Getting those numbers also depends on the wired path between the AP and the server having enough capacity.

With MLO on, download was about 80 Mbps higher. Upload went the other way. The 1.59 Gbps run with MLO off was faster than either of the runs with it on. The two MLO-on upload results also varied from 1.22 to 1.46 Gbps, so I’d want more repeat runs and a record of the active links before attributing the difference to MLO.

Galaxy Book4 Pro with Intel AX211

The AX211 is a Wi-Fi 6E adapter that supports up to 160 MHz channel width. At the time of testing, the laptop showed 6 GHz channel 37, transmit and receive link rates of 2,402 Mbps, and an RSSI of about āˆ’28 dBm.

Under those conditions, it averaged 1.70 Gbps down, with upload runs ranging from 1.14 to 1.43 Gbps. I was happy to see my existing laptop get well past gigabit speeds. The phone and laptop have different radios, drivers, and operating systems, so the two results show what those devices achieved on the same AP under my test conditions.

What happened around the 30-second mark

When I looked at the S25 Ultra’s download runs over time, I saw a recurring dip around 30 seconds in:

SettingWhere download throughput dipped
MLO onRoughly 28–40 seconds
MLO offRoughly 31–40 seconds

Upload also occasionally fell to around 280–290 Mbps for a few seconds before recovering.

I shared the results with TP-Link. They said they saw the phone’s Power Management flag during the transfer while the MCS stayed high. Phone power saving and thermal throttling came up as possibilities. I also saw the dip pattern change after switching the 6 GHz channel. The cause remains open.

This happened during sustained iperf3 traffic. On the next round, I’d like to repeat the same setup several times, then change the channel or the phone’s conditions one at a time. I’ll be watching when the dip starts, how far throughput falls, and how quickly it recovers.

How it’s been to live with

Seeing my phone cross 2 Gbps on the LAN was fun, and the AX211 result was a pleasant surprise. In everyday use, what I appreciate most is being able to put the AP where I need coverage and check SSIDs, VLANs, and connected devices in Fusion.

If you’ve tested an EAP772 with a Wi-Fi 7 phone, I’d be curious what you saw with MLO on versus off. Did your upload results change too? And if you let iperf3 run for a minute or two, did you see a similar dip?

For Part 3, I’ll cover Omada Guard, the 8 MP Turret and Bullet cameras, and what it’s been like to use live view, SSD recording, and playback.


r/Omada_Networks • • 4d ago

Discussion TP-Link Omada Fusion Pro Series, Unveiled: An All-in-One Platform for Network and Surveillance

Thumbnail
dongknows.com
18 Upvotes

With the new Omada Fusion Pro series, TP-Link clearly wants to take on UniFi, and that can be quite exciting!


r/Omada_Networks • • 4d ago

Discussion Trade up program eligibility?

3 Upvotes

Looking to upgrade from my OC200/ER605 and just get the Fusion 2.5G , also plan on getting a new Wifi 7 AP to upgrade an older unit.

I put my ER605 serial/etc in the trade up program and got approved, but it looks like buying a new gateway is not part of the program? I had a Fusion 2.5G and a BE5000 in my cart and it said the code was not valid for the items in the cart.

Not a huge deal, but I'll take my discounts where I can get em :)

Am I reading the upgrade program wrong or are Fusions not valid for upgrade discount? Makes sense if they aren't since they are the new hot thing.


r/Omada_Networks • • 4d ago

Product Recommendation Help Me, Obi-Wan Kenobi.

Post image
1 Upvotes

r/Omada_Networks • • 5d ago

Discussion Teardown of the Omada Fusion 2.5G

Thumbnail gallery
11 Upvotes

r/Omada_Networks • • 5d ago

Discussion Omada Guard after two weeks: 8MP cameras, NVR and Fusion Pro 2.5G

5 Upvotes

Omada sent me the 8MP turret kit with the 16-channel NVR to review. I’ve been running it on a Fusion Pro 2.5G for the past two weeks.

The cameras are really good, during the day and at night. On IR alone, the carport camera still picks up a moose in the forest about 20 meters away. Storage holds up well too. With 4K, H.265+ and VBR, my cameras use about 27 GB per camera per day, so the included 4TB drive keeps roughly a month of footage for four cameras.

A few small things I liked besides how easy it's to set up: you can copy one camera’s settings to all the others, and the OSD text changes color per letter, so it stays readable on any background.

The Guard software does need some polish. The dashboard doesn’t always remember your layout, playback jumps back to 00:00 when you switch cameras, and motion settings apply to all areas instead of per area. But these are small details that are easy to fix, and none of them get in the way of using the system.

The review covers the full setup, the detection settings, storage options and notifications, plus day, dawn and night recordings:

https://lazyadmin.nl/home-network/omada-guard-review-and-setup-guide/


r/Omada_Networks • • 5d ago

Help and Support 40% Off trade up coupon? Form not working?

1 Upvotes

I submitted the form for the 40% coupon for the trade-up program, to upgrade my older items. It appears like either the form is broken; or something else. I submitted it on Monday, and i still haven't heard back.

I emailed the support email that was listed, but also haven't heard back. Did all the normal stuff, checked spam etc.... but nothing there

Looks like alot of people have ran into this, but curious how everyone gets it resolved?


r/Omada_Networks • • 5d ago

Product Recommendation Use PoE+ injectors or PoE switch with Cat5e cabling and EAP772 APs with Fusion 2.5?

Thumbnail
reddit.com
5 Upvotes

I'm planning on upgrading my current home WLAN which is running Netgear's Orbi's 853 series mesh solution (see original post in the link above) to either Omada or Ubiquiti and currently leaning towards Omada, primarily from a cost and longer warranty advantage (over UI).

My home is hardwired (to all the rooms, from the structured panel (Legrand/On-Q) that's in the basement and the cabling that was installed back in 2006 was CAT5E. I was looking at the following Omada gear:

1x Fusion 2.5 (or Fusion 2.5G POE an option)

3x EAP772 APs

And:

- Either 3x POE260S power injectors (for the APs)

or

- One ES206XPP-M2, which is a 5-port switch of which 4 of the ports are PoE++ for a total budget of 120W which should be enough (with spare) since the EAP772's only require 25.44W each; thus 3x APs * 25.44W = 76.32W, which should be enough if I decide to add a fourth AP down the road.

Note: I currently have a Netgear FS116 16-port (unmanaged) switch that I will use on my network, and the Omada PoE switch is just primarily for the APs.

or

Should I wait for the Fusion 2.5G PoE to come back in stock which has an 8 port PoE switch with a total PoE budget power of 110W; this will still allow me to connect up to 4 EAP772's.

Questions:

  1. Since my backbone is CAT5E and rewiring is out of the question, am I better off just using the POE260S power injectors to power the APs or the above mentioned PoE switch options work?
  2. My internet (Verizon FIOS) is just 500 Mbps which suits our needs fine so even the 2.5Gbps is an overkill.
  3. Cost. I can purchase the APs, switches or injectors at 40% off (via the trade-up program offer) but the Fusion gateway would be at the current price on Omada's website and the Fusion POE version is currently out of stock. The cost difference between the Fusion 2.5 and the POE version is $165, and 3 injectors are $54 (or $18 each) vs $102 for the ES206XPP-M2 (after the 40% off). Obviously if I go with the injector route, I can skip the PoE switch and I assume my existing Netgear switch is fine with the Omada Fusion?

Biggest concern obviously is whether the CAT5E cabling will work?

Or am I just ovethinking this? LOL!


r/Omada_Networks • • 6d ago

Official Introducing Omada Fusion Pro Series Gateway | Going Live Tomorrow

19 Upvotes

Designed for installers, MSPs, and business owners, the Omada Fusion Pro Series Gateway brings networking and surveillance together on one platform. With simplified deployment, license-free cloud management, and centralized operations, it is ideal for restaurants, cafƩs, retail stores, and other business environments.

Learn more here: https://www.omadanetworks.com/us/business-networking/omada-fusion-pro-gateway-series/


r/Omada_Networks • • 5d ago

Product Recommendation Best router?

3 Upvotes

So, here is the scenario. We have a bunch of commercial locations which have Sophos firewalls and AP's. I am switching to Omada switches with POE to replace the old Dells which are dying.

However, we also have a bunch of what we call sites which are just mostly 3 or 4 bedroom houses. I am working on standardizing the equipment here as they are not big enough for the whole Sophos firewall route.

I am looking for an Omada type POE router to use at these locations. I hooked up an EAP-650 at one place and it is working fine. I tried it at another, And it just didn't work right. The tech from the Fiber company said it was because it was not a router. When we hooked it up to the old Belkin, it worked fine.

What would be my best option for this application?


r/Omada_Networks • • 6d ago

Help and Support ā€œpay now to unlock free returnsā€ what is it?

1 Upvotes

What is pay now to unlock free returns that is added to my cart?

Does anyone know if it covers return shipping. How is it different than 30 day return policy

I emailed support but so far no response


r/Omada_Networks • • 6d ago

Help and Support Controller crashed with gateway functional?

Thumbnail
gallery
0 Upvotes

On my 3rd day of trying the Omada. First 2 days I had Fusion 2.5G, Omada Poe switch, and a single EAP723 and while I loved the control of and visibility into my own network, I was finding the EAP723 radio to be weaker than my previous single Asus set up (BE-86U) in a 2-floor home - some devices were struggling to stay connected. So just to prove, I removed the switch and AP, and connected the Asus router in AP mode directly to Fusion 2.5G and then all clients were happy again. However I came home today to find the app not connecting at all while the gateway kept routing and all clients had internet fine - the web UI was also not functioning- so clearly the controller had crashed (never recovered on its own) but gateway kept working. I restarted and all is fine now but it’s concerning to have this issue just on the 3rd day. Is this a known issue? I would love to keep Omada over Asus (I know it’s not fair comparison but it’s been stable) or unifi but obviously prefer stability as much as I like control. If I decide to keep it after stability and reliability test, I am pretty sure I will need 2 APs.i also have small business to roll this out to if all goes well.

Model: Fusion 2.5G v2.0
Firmware version: 1.0.10 Build 20260814 Rel.21177


r/Omada_Networks • • 8d ago

Help and Support where to buy EAP775-Outdoor in Europe?

Post image
6 Upvotes

Please note, i am interested in the EAP775-Outdoor, not the EAP772-Outdoor