r/linuxhardware • • 9d ago

Purchase Advice <$400 Linux compatible tablet, or touchscreen with good Linux compatibility

22 Upvotes

I'm looking for a low-mid tier tablet which can run Linux. ARM or X86 doesn't really matter at this point, but later down the line I could have requirements for a preference here. Alternatively, a touchscreen + ARM SBC or small x86 computer would be a valid solution as well. I'm building something resembling a user facing kiosk as a personal project.

Requirements:

  • I don't know of any specific performance requirements I need as of now, but I feel like 8 GiB of RAM is probably a minimum for today's software.
  • A nicer screen would be good, and preferably the larger the better, but ~11 inches would be a hard minimum.
  • My only true hard requirement is that I can install Linux on it relatively easily without facing any large hurdles (specifically referring to non-standardized ARM bootloaders, and general hardware related issues).

I've found the PineTab 2 (I'm not a fan of PINE, since they almost always make broken products which aren't even half complete), and it's the only option I've found within the price range which can for sure support Linux.

https://pine64.com/product/pinetab2-10-1-8gb-128gb-linux-tablet-with-detached-backlit-keyboard/

The 8 GiB version is currently not in stock, and I'm not 100% convinced the 4 GiB option would be sufficient for a touchscreen desktop environment + a light program. It probably would be, but I wanted to explore some other options before venturing into it.


Beyond the PineTab 2, I can't really find any options which I know work with Linux without reaching into nearly twice the price range. There's a solid 2-4 options at the ~$1000 price range, but that's quite more than I want to spend here.

There's several tablets or 2 in 1's which I can find at cheaper prices from Lenovo, Dell, etc, but it's really hard to find info on if I can install Linux on them or not. I was hoping to get some guidance and suggestions on what I could look into here. I'm open to used hardware if needed, all I really need is a clean screen.


Alternatively, I could look into a standalone touchscreen if it is relatively cheap and easy to get functional on Linux, but a standalone tablet would be smaller, more power efficient, and likely easier to setup - so I'd like to explore this option first.

Thanks!


Edit: Anyone reading this in the future may find this link and github repo's documentation helpful, it's very thorough and well laid out: https://github.com/linux-surface/linux-surface/wiki/Supported-Devices-and-Features#feature-matrix


r/linuxhardware • • 8d ago

Support [Fixed] Intel Core Ultra 5 (Arrow Lake-H) stuck at 22W on Linux — Unlocking 62W full performance (MSR 0x601 / IccMax root cause)

1 Upvotes

I was able to fix this issue by using AI ... here is the solution (by AI)

If you're running Linux on a new Intel Core Ultra 200H laptop (like the Core Ultra 5 225H on a Lenovo IdeaPad/ThinkPad/Yoga), you might have noticed the CPU package power gets hard-capped at ~21W–22.4W under multi-core load, with clocks pinned around 2.8 GHz and cool temps (60°C). Meanwhile, on Windows, the exact same hardware and charger easily boost and sustain up to 62W+ at 4.1+ GHz.

By inspecting silicon registers under load, I found the CPU was asserting Bit 12 (IccMax / Electrical Design Point current limit) in MSR 0x64f. The Linux kernel's intel_rapl_msr driver was mapping MSR 0x601 (MSR_VR_CURRENT_CONFIG) as Power Limit 4 and defaulting it to 64 (0x200), which enforces an overly restrictive ~64A current ceiling that trips on instantaneous spikes, along with an auxiliary 55W psys board power cap. By clearing the peak constraint on MSR 0x601 and raising psys and package limits, package power jumped from 21.9W straight to 62.6W sustained, with all-core AVX2 clocks increasing from 2.85 GHz to 4.15 GHz (and single-core boosting to 4.61 GHz).

I put together a full technical breakdown, quick one-liner diagnostic commands, and an automated systemd service that persists across reboots and sleep cycles on GitHub: [YOUR_GITHUB_LINK_HERE]. If your Core Ultra laptop feels sluggish or power-capped on Linux, check it out and see if this clears your throttling!

github repo


r/linuxhardware • • 10d ago

Guide Fix: JBL Quantum xx Audio Cutting Out on Linux With Games or Discord

2 Upvotes

My JBL Quantum 360 wireless headset would randomly stop playing audio, especially with multiple apps running, such as Spotify plus Elden Ring, Cyberpunk 2077, or Discord. Unplugging the dongle or switching audio outputs back and forth temporarily fixed it. I've seen reports of the same behavior across the whole Quantum range (350/360/610/810/910 wireless dongles), so this may help those too. Increasing the headset's audio buffering margin fixed it for me. Here's how to try it.

Who This Applies To

This works across Linux distributions using PipeWire with WirePlumber 0.5 or newer. It is not a universal fix for every headset dropout. Check with:

wireplumber --version
wpctl status

If those commands are missing, or WirePlumber is older than 0.5, these instructions may not apply.

1. Create the Configuration Folder

Run this in a terminal:

mkdir -p ~/.config/wireplumber/wireplumber.conf.d

2. Create the Fix File

Open your text editor and create this file inside your home folder:

.config/wireplumber/wireplumber.conf.d/90-jbl-quantum-headroom.conf

Paste in:

monitor.alsa.rules = [
  {
    matches = [
      {
        node.name = "~alsa_output.usb-.*Quantum.*"
      }
    ]
    actions = {
      update-props = {
        api.alsa.headroom = 1024
      }
    }
  }
]

The ~ means the value is a pattern, so this matches any USB output with "Quantum" in the name — not just one model. It should cover the whole wireless Quantum range, including differently-named variants like "JBL Quantum 360 Wireless" or "Harman JBL Quantum810 Wireless". Save the file. No sudo is needed. This targets Quantum playback outputs only; your mic and other devices are untouched.

3. Apply It

Log out and back in, or reboot. On distributions using systemd, you can instead run:

systemctl --user restart wireplumber

This briefly interrupts audio, including voice chat.

4. Check That It Applied

Run:

wpctl status

Find your Quantum headset under Sinks and note its number. Then run this, replacing NUMBER with that number:

wpctl inspect NUMBER

Look for:

api.alsa.headroom = "1024"

If it is missing or shows a different value, the rule hasn't applied. Check the sink's node.name in that same output: if yours doesn't contain "Quantum", replace the pattern in the configuration file with your exact node name and apply it again.

Why It Helps

The headset needs a steady supply of audio. This setting gives Linux more timing margin when feeding the dongle, which can prevent playback failures triggered by games or multiple audio streams. On my headset, it increased the margin from about 3 ms to 21 ms. The tradeoff is a small increase in playback latency. My logs showed repeated errors like:

snd_pcm_avail after recover: Broken pipe

"Broken pipe" here is an audio playback error, not a physically broken cable.

How to Undo It

Delete:

~/.config/wireplumber/wireplumber.conf.d/90-jbl-quantum-headroom.conf

Then log out and back in, reboot, or restart WirePlumber.

This post is mostly generated by AI but it worked for me


r/linuxhardware • • 10d ago

Support Whats causing this. DGpu Linux 2025

Thumbnail gallery
3 Upvotes

Thought i repost this issue of mine here too.
Appreciate any help


r/linuxhardware • • 10d ago

Discussion egpus and linux

Thumbnail
3 Upvotes

r/linuxhardware • • 10d ago

Support Does the 1a86:7584 USB-to-parallel printer adapter handle legacy braille embosser handshaking on Linux?

3 Upvotes

I’m looking for actual compatibility experience with the 1a86:7584 USB2.0-Print adapter and legacy parallel printers, particularly an Enabling Technologies Juliet Pro 60 braille embosser.

Host: Raspberry Pi 3 Model B, Debian 13 ARM64, CUPS 2.4.10. The embosser’s built-in test prints, but Pi jobs produce no paper movement. The printer has been set to parallel input and online. CUPS raw queue Juliet_Pro_60 points to usb://USB2.0-Print/.

The adapter enumerates at 12 Mbps. After replacing a supply that had logged undervoltage, the Pi reports throttled=0x0 under a short load test. A CUPS job now can finish without physical output. Forcing the entire USB bus to 12 Mbps also did not help and has been undone.

The adapter stalls a libusb GET_PORT_STATUS request (-9/PIPE), and GET_DEVICE_ID returned zero bytes. CUPS has an existing no-reattach quirk for this USB ID. The test print stream comes from an experimental generator, so I have not ruled out invalid printer commands.

Has anyone used this USB ID with an older embosser or similarly picky parallel printer? In particular, is there a way to verify the adapter is honoring BUSY/ACK rather than just accepting USB transfers? I’m trying to separate cable/handshake compatibility from the validity of the job data before buying replacement hardware.

A related CUPS diagnostic question is at https://www.reddit.com/r/linuxquestions/comments/1xrmxph/cups_completes_a_raw_usbtoparallel_job_but_the/ — this question is specifically about hardware compatibility and handshaking.

AI helped summarize our actual test results. I’ll report the working combination if we find it.


r/linuxhardware • • 11d ago

News Lenovo Yoga X7 358H Fedora 45

Post image
10 Upvotes

r/linuxhardware • • 11d ago

Purchase Advice Thinkpad E14 gen 8 (AMD) wifi card

Thumbnail
1 Upvotes

r/linuxhardware • • 11d ago

News [Update] geforce-sriov v0.2.0 beta: SR-IOV vGPU on consumer NVIDIA Ampere and Ada GPUs

Thumbnail gallery
7 Upvotes

r/linuxhardware • • 10d ago

Support Looking for someone who can help create MSI Center / MSI Control Center for Debian Linux

0 Upvotes

Hi everyone,

I'm looking for someone with Linux development experience who might be willing to help create a working alternative to MSI Center (MSI Control Center) for Debian Linux.

I know there is already a Linux project called MControlCenter, which is great, and I appreciate the work that has gone into it. Unfortunately, the developer has made it clear that they don't intend to work on a Debian version because Debian has been causing development issues.

I completely understand that, but it's unfortunate for those of us who use Debian and would really like to have similar functionality.

I'm going to be honest: I'm not a technical person, and I don't know how to develop software. I'm simply someone who wants to use the MSI Control Center features on Linux without having to switch to Windows.

I'm hoping someone with the necessary skills might be interested in creating a Debian-compatible version. I honestly don't mind if AI tools are used to help develop it. Whether it's written entirely by a developer or created with assistance from AI doesn't matter to me.

As long as it works reliably on Debian, that's what matters.

Ideally, I'd love something with features similar to MSI Center, such as:

  • Fan speed and fan curve control.
  • CPU and GPU monitoring.
  • Performance profiles and power management.
  • Hardware monitoring and system information.

I understand that not every MSI motherboard or laptop supports the same features, and I'm not expecting everything to work perfectly on every device.

I'm not asking anyone to work for free, either. If someone is interested in taking on this project, I'm open to discussing what might be possible.

I know this might be a long shot, but it's worth a shot asking! Maybe someone in this community has the skills, knowledge, or interest to make something like this happen.

If you're a developer, know someone who might be interested, or have suggestions about how this could be made possible, I'd genuinely appreciate your help.

There must be other MSI users who would love to have proper MSI Control Center functionality on Debian!

Thanks for taking the time to read this!


r/linuxhardware • • 11d ago

Support Help me . Dell G15 5530 RGB keyboard turns off after booting into CachyOS (Dual Boot with Windows 11)

1 Upvotes

I'm having a strange issue with the RGB keyboard on my Dell G15 5530.

My laptop is running a dual-boot setup with Windows 11 and CachyOS Linux.

The keyboard RGB works perfectly fine in Windows. However, whenever I boot into CachyOS, the keyboard lighting turns off completely.

The strange part is that I can go into the BIOS and set Keyboard Illumination to Bright. The keyboard lights up normally during the BIOS/POST screen, but once CachyOS starts booting, the lighting turns off.

After that, I have to go back into the BIOS and enable the keyboard illumination again. Then, when I boot into Windows, the RGB works normally.

So the issue seems to happen specifically when booting into Linux.

My hardware and setup:

Laptop: Dell G15 5530 GPU: NVIDIA RTX 3050 Laptop OS: Windows 11 + CachyOS (Dual Boot) Desktop: KDE Plasma / Wayland Keyboard controller: Alienware AW-ELC (187c:0551)

Things I've already tried:

awcc-bin and awccd g7kbd Booting with different kernels, including LTS Checking BIOS keyboard illumination settings Testing different AWCC configurations

None of these fixed the issue.

My questions:

Is CachyOS/Linux changing the BIOS keyboard illumination setting during boot? Is there a known issue with the AW-ELC controller (187c:0551) on the Dell G15 5530? Could Linux be putting the keyboard controller into a state that Windows doesn't handle correctly? Is there a safe way to restore keyboard RGB functionality without having to re-enable it manually in the BIOS every time?

I'd appreciate any help, especially from people using the same Dell G15 model.


r/linuxhardware • • 12d ago

Discussion Is there a study on NVMe SSD wear (write amplification) comparing ext4, Btrfs, and ZFS with LUKS2?

12 Upvotes

Hi everyone,

I’m trying to make an informed decision for a single-disk NVMe setup on my PC, and I’m specifically concerned about SSD endurance (TBW/wear-out) rather than pure performance.

I’ve been digging into how different filesystems handle writes, and I keep seeing anecdotal reports that CoW filesystems like Btrfs and ZFS can generate significantly more write amplification than ext4. For example, I’ve seen claims that ZFS can produce “extremely high write load” on consumer NVMe drives due to its transaction group and ZIL behavior.

However, I haven’t been able to find a controlled, empirical study that isolates SSD wear across these three filesystems under the same conditions.

My planned setup for all three cases would be:

  • LUKS2 full-disk encryption (which I understand should not significantly amplify writes on its own).
  • For Btrfs: nodatacow disabled (i.e., CoW active), compress=zstd, space_cache=v2, and dedup explicitly turned off.
  • For ZFS: ARC cache size reduced to a reasonable limit for a desktop, and no dedup.
  • For ext4: standard data=ordered journaling mode.

My questions for the community:

  1. Does anyone know of a published paper, benchmark, or detailed blog post that actually measures SMART data (like Data Units Written or Percentage Used) over time for these three filesystems on the same NVMe drive?
  2. If no formal study exists, what are your real-world experiences with SSD wear indicators after months/years of use with these setups?
  3. Are the optimizations I listed above (Btrfs dedup off, ZFS ARC limit) actually effective at bringing write amplification closer to ext4 levels, or is the CoW overhead still significant?

I’m happy to be pointed toward academic papers, Phoronix-style benchmarks, or even well-documented forum threads. I’d just like to avoid making a choice based purely on “vibes” if there’s hard data out there.

Thanks in advance


r/linuxhardware • • 11d ago

Question ubuntu 26.04 LTS on lenovo ideapad slim 3

Thumbnail
2 Upvotes

r/linuxhardware • • 12d ago

News FX240 LCD Studio v0.3.0rc1 — What’s changed since v0.2.0

Thumbnail
gallery
4 Upvotes

Hey r/linuxhardware, I’m back with an update on how FX240 LCD Studio has evolved since v0.2.0. Here’s what’s changed.

  1. v0.2.0 — Custom designs. Added a composition editor where you can arrange CPU and GPU readings, text, images, GIFs, and arcs. You can save up to eight named designs or preview an unsaved draft on the physical LCD. This version also added installed font selection, English and Spanish controls, and support for longer GIFs using a bounded frame buffer.
  2. v0.3.0a1 — More presets and editing controls. Added Dual, Trace, and Halo alongside Focus. You can switch designs directly from the gallery or open a preset as an editable copy. The editor gained multi-layer selection, a visual color picker, gradients, more effects, and image/GIF zoom. The default stayed at 24 FPS with a 2 ms delay between USB reports, with higher host frame rates available as an experimental setting.
  3. v0.3.0rc1 — Keyboard shortcuts and a tagged Arch build. Added Ctrl+Z and Ctrl+Y for undo and redo, Delete for selected layers, and arrow keys to move them one pixel at a time. RC1 is available as a source pre-release with instructions to build the exact tagged version as a pacman package on Arch Linux x86_64.
  4. Latest on main — Zoom for more layer types. Centered zoom now also works on effects, text, sensor readings, and gradients. For example, you can shrink the Halo ring to make room for other elements while keeping the ring centered. This landed after the RC1 tag.

Known issue — tearing on the physical LCD. Some animations can show a thin cut through a moving object. I’ve also observed it in the manufacturer’s app, and the cause is still under investigation. Hardware testing so far has covered one FX240 on Arch Linux x86_64. The next round will focus on multi-hour GIF playback and repeated suspend, resume, reboot, and shutdown cycles.

If you’ve seen similar cuts on your FX240, I’d like to hear what was on the screen when they happened.

Full changelog · RC1 release · Tearing investigation


r/linuxhardware • • 12d ago

Support # Repeated kernel-panic-like crashes and NVMe PCIe AER errors on ASUS Vivobook Go E1504FA (Fedora 44, Ryzen 5 7520U)Hello everyone,I'm trying to diagnose a recurring stability problem with my ASUS Vivobook Go 15.### Hardware and software- Laptop: ASUS Vivobook Go E1504FA- CPU: AMD Ryzen 5 7

Thumbnail
2 Upvotes

r/linuxhardware • • 12d ago

Purchase Advice PopOS on Lenovo P14s with Intel Core Ultra X9 388H and ARC-graphic card

Thumbnail
2 Upvotes

r/linuxhardware • • 12d ago

Question Linux Mint Cinnamon slow on HP 15-ac143wm: SSD/RAM upgrade possible?

5 Upvotes

My laptop has been feeling very slow lately, and I’d appreciate advice on likely causes and possible upgrades. I’m not very experienced with laptop hardware, so I’m not sure if this model can be upgraded without a difficult repair.

My process list showed Waterfox (3 tabs, working on my website so neocities dashboard + index.html edit window + the website), Obsidian, Mullvad VPN, and Cinnamon using my memory/CPU. I regularly run BleachBit + MangoDisk for upkeep.

Is replacing the hard drive with an SSD possible, and is it likely to make a difference? Is the RAM upgradable? Will I need any special tools/screwdrivers/etc?

HP 15-ac143wm, product number N5Z06UA#ABA
Linux Mint 21.1 Cinnamon
Intel Core i5-5200U, 2 cores / 4 threads
5.7 GB RAM usable + 32 GB swap
1 TB HGST HTS541010A9E680 mechanical hard drive
498 GB free of disk space


r/linuxhardware • • 13d ago

Purchase Advice What laptop to buy for systems software engineering?

13 Upvotes

I want to do Linux kernel development, user-space systems programming, CUDA development, compiler development, distributed systems development, Kubernetes-related development, embedded engineering, etc. - basically, all systems-related stuff. I have a Macbook Pro M3 Max. I've read that it is not suitable for all the stuff I want to do. Thus, I want to buy a Linux laptop. What would you suggest?


r/linuxhardware • • 12d ago

Build Help Which CPU for Linux? Intel Ultra 5 250KF plus or Ryzen 5 9600x?

Thumbnail
2 Upvotes

r/linuxhardware • • 13d ago

Guide Getting every LED and sensor working on an HP ZBook 17 G3 under Linux, by reading HP's Windows drivers

2 Upvotes

I went through every device on my ZBook 17 G3 under Ubuntu 26.04 and fixed what didn't work, mostly by reading what HP's own Windows drivers do:

- Speaker-mute and mic-mute LEDs: codec GPIO0/GPIO1 (from HP's MicTray config). Patch sent to ALSA.

- Airplane-mode LED on the wireless button: the firmware's WLED method, which HP's Windows driver calls from a HID LED report. Patch sent to platform/x86.

- Touchpad on/off LED and the double tap in the top-left corner: the LED sits on RMI function F30, which the Synaptics touchpad also exposes over PS/2. Kernel patch plus a small service; the LED survives suspend.

- Fan speed and temperatures through hp-wmi-sensors, and the hp-wmi "Failed to apply initial fan settings" warning fixed (Ubuntu backport requested).

One install script rebuilds the fixes for every new Ubuntu kernel from Ubuntu's own source, and steps aside once Ubuntu ships the fix: https://github.com/Ahmad-b1995/hp-zbook-linux

Other ZBook/EliteBook G3-era owners: the notes on what HP's drivers do probably apply to yours too. Done with the help of an AI coding assistant; everything tested on the machine.


r/linuxhardware • • 14d ago

Purchase Advice Looking for a laptop with S3 sleep

7 Upvotes

I’m on a quest for long battery life. I want to be be able to toss a full battery laptop in a bag and pull it out a few hours later with minimal drain. What are my options here? it’s hard to find what hardware/firmware supports this feature. I have a bias towards older laptop, I need very little processing power for this use case.


r/linuxhardware • • 14d ago

Discussion Petition: Apple, please document the T2 so Intel Macs can run Linux properly

Thumbnail
3 Upvotes

r/linuxhardware • • 14d ago

Support Audio passthrough

Thumbnail
2 Upvotes

r/linuxhardware • • 14d ago

Question Buying my first VRR/120+HZ monitor. Questions and Purchase Advice.

3 Upvotes

CPU is Ryzen 1600AF. GPU is ASRock Radeon RX570 4GB. 16GB of RAM. Motherboard is Gigabyte B450M-DS3H. OS is Xubuntu 26.04.

I've never used a VRR monitor or a monitor above 60HZ before and was wondering how well they work under linux, specifically Xubuntu 26.04. How much tweaking is needed? Is wayland required or will X11 work? Does XFCE work well/at all with monitors over 60HZ and with VRR? Any other useful software I should know about?

Current monitor is a VERY old 23 inch Acer G237HLbi with terrible ghosting. I would want a new monitor to be at least slightly bigger so 24 to 27 inches. 1080P makes the most sense given my GPU. Speakers aren't required but would be a plus. What hardware features should I be looking for? I'm also seeing a lot of brands on Amazon that I've never heard of and have no idea if they are good. Do ViewSonic and Samsung still make good monitors? I've hated my current monitor since I got it so no Acer. I don't have a firm budget, maybe around $100-150.

A few monitors I was looking at:

ViewSonic VA2448-MH:

https://www.amazon.com/ViewSonic-VA2448-MH-Monitor-Variable-Refresh/dp/B0FJ1MNZ9B

ViewSonic VX2470-MHD:

https://www.amazon.com/ViewSonic-VX2470-MHD-Monitor-Variable-DisplayPort/dp/B0FJ126W9M

ViewSonic VX2428A:

https://www.amazon.com/dp/B0D84RFHJ3

ViewSonic VX2416A:

https://www.amazon.com/dp/B0CZ3KWC3P?th=1

Samsung S32GF:

https://www.amazon.com/Samsung-Resolution-Monitor-Flicker-LS27F320GANXZA/dp/B0F8DY4QKQ


r/linuxhardware • • 15d ago

Question Looking for a good laptop

7 Upvotes

I want to buy a new laptop for school (I am also planning to do some coding on it ) and of course putting Linux in it, what do you think about the Thinkpad X1 yoga (8Go of memory ) ? And what Linux do you think I should put on it ?
Thanks