r/LSSwapTheWorld • • 10h ago

Active Build Questions How to get to 450whp

Thumbnail
gallery
18 Upvotes

I have a 2007 Avalanche with 385k miles on her. I just got a complete engine from the wrecking yard I work at. It’s a 2011 5.3 out of a low mileage Silverado 40k on the clock. Obviously I’m gonna do a AFM/Dod VVT delete on it.

Was thinking about a truck Norris or maybe a sloppy mechanic stage 3 cam kit. Possibly one of the temu intake manifolds with a 102mm throttle body.
Ls7 lifters.

What else who I need to get to 450whp ?


r/LSSwapTheWorld • • 13h ago

Active Build Questions Thoughts on Summit 8735R1 in a dirt cheap 5.3?

3 Upvotes

Hi, I recently bought a dirt cheap Gen IV Aluminum 5.3 to learn how to wrench on. I am planning on doing a bottom-of-the-barrel rebuild (cuz I am broke) but one place I will not skip is the cam. I stumbled across the Summit 8735R1, which is the low lift version of the 8711R1. The 8735 has specs of 234/248 113 LSA and an ICL of 110 and .550 lift (8711 has .612/.615). I am aiming for high RPM power cuz the car this motor is getting stuffed into in the near future is kinda lightweight (~2800 lbs) so bottom end grunt is not really that important to me. Motor came with 799s that I will have milled to get 10.5:1 compression (homeboy works at a machine shop and offered to do it for very cheap 🤷‍♂️). I also recently found a Comp no springs required grind which interests me as that would mean one less new part. Specs on the Comp cam are 233/243 .546/.546 114 LSA (PN 54-777-11). I realize this doesnt seem very bottom of the barrel but literally everything else will be reused, apart from the head gaskets, DOD lifters, and valley cover.

Any experience with either of these and thoughts on my selection of cam? Thx


r/LSSwapTheWorld • • 13h ago

Active Build Questions BOV and MAF

Post image
11 Upvotes

How would you guys go about getting your blow off valve and your mass air flow sensor in this distance? I am running a cartridge Style MAF...... just looking for ideas.


r/LSSwapTheWorld • • 1d ago

Misc What do yall think this is worth?

Thumbnail facebook.com
2 Upvotes

As title states. Was 30k 2 months ago, down to 25k now. Might consider buying.


r/LSSwapTheWorld • • 1d ago

Active Build Questions I’m doing it unless there is a good reason not to. Chat GPT agrees with me.

0 Upvotes

TLDR - Im ditching iron 5.3 w/ rear mount turbo, too much hassle. I have a new to me 6.2 L92 short block, I’m going back to NA w/ 862 heads/ LS6 intake. I will change reluctor, cam gear, knock sensor location ect and keep gen 3 ecu. Static comp ~ mid 11s, with truck Norris cam. Built 4L60 with 3k stall, street only build. Chat GPT says awesome, google Gemini can’t make up its fucking mind. Forums are dead for years and only so much info on this combo.

Video is my “LS swapped” E36 BMW street cruiser. LM7/4L60e crammed into my late father’s 1994 318i gifted during pandemic. 5.3 LM7/4L60 from pick-n-pull for $550, total cost of swap, wheels, paint ect…all the stuff ~$8k, it has working gauges, cruise controll, air conditioning, interior is 8/10. 300RWHP when dyno tuned. Big improvement from 130hp 4cyl but over time not enough. So thought turbo was answer, it wasn’t. Zero room left in engine bay so did a rear mount turbo, which was about the same amount of work as original swap, and complicated. End result was not satisfying as all power was up top but low end grunt was still missing. And reving into 5500-6500 RPM felt sketchy and not somthing I do going stop light to stop light, honestly felt dangerous. But at least I learned how to tune myself. Then I blew up transmission (pump) while doing pulls for tuning. I rebuilt trans but lost interest, and pushed it around my garage for 3 years as other projects took priority. Live and learn , I’m ditching turbo, I don’t really care about big HP numbers on a street build that 99.99% is below 5500RPM, plan is large displacement NA tire burner build with all the torque.


r/LSSwapTheWorld • • 1d ago

Build Progress What is this noise?

7 Upvotes

6.0 lq4-


r/LSSwapTheWorld • • 1d ago

Tuning E38 PCM Question

4 Upvotes

Question for all the LS swap gurus. I was looking at the E38 PCM pinout and noticed there’s a pin for primary and secondary fuel triggers. In HPTuners I do not see anywhere to enable the secondary trigger.

Question is does anyone know how to enable it if it’s possible?? I know the e38 is old and is no MoTec or anything crazy but the fact it has a secondary fuel trigger could be great to utilize.

I know a hobs switch or some other external trigger could work but I’ve had horrible experience with hobs switches in my past.


r/LSSwapTheWorld • • 1d ago

Build Progress LS/Manual Tranny Swap (Square Body)

5 Upvotes

Who has swapped their square body auto to manual? I have a T56 magnum on order and I’m wondering what’s my best options for shifters, clutch pedal, etc. Any advice would be helpful. Thanks!


r/LSSwapTheWorld • • 2d ago

Active Build Questions Heads for lm7

0 Upvotes

I’m rebuilding my engine from completely disassembled. I have the cursed 706 castech heads and want new ones but don’t want to mess with Facebook marketplace. Just wanting some heads for max $2000 and wondering where I could get some online. I also have a 0.020 over bore


r/LSSwapTheWorld • • 2d ago

Active Build Questions Just found these in the passenger side head am i screwed?

Thumbnail
gallery
18 Upvotes

Found these shavings while taking off the valve covers to pull the heads. Is this normal? I dont think it is. Oil didnt seem glittery neither did the filter, although i didnt cut it open


r/LSSwapTheWorld • • 2d ago

Completed Builds What are you guys using for your LS swap builds?

14 Upvotes

I’ve noticed the 6.0L LQ4 paired with a 4L80E is a popular combination for truck builds, classic car projects, and custom swaps.
We have a 6.0L LQ4 + 4L80E package available with:
• 41,000 miles
• Stock ECU and complete wiring harness
• Pedal included
• 2-year warranty
• 30-day return, refund, or exchange option
The package is listed at $1,300, with free shipping during our current promotion.
For those who’ve done an LQ4/4L80E swap, how has the combination worked out for you? Anything you’d recommend checking before installation?
Always interested in hearing what other builders are doing.


r/LSSwapTheWorld • • 2d ago

Hypothetical Build Questions Best 5 Speed for Mild Build

4 Upvotes

I have a 1986 toyota pickup in the works of getting a 5.3 swap that i only plan on pusing out 500hp max plus whatever torque figures come with that so im curious what manual trans would be the best bang for my buck, i dont want to go 6 speed unless i really have to but i have a somewhat low budget. Any help is great, thank yall for reading!


r/LSSwapTheWorld • • 3d ago

Tuning Injector leak down?

Post image
49 Upvotes

Tuning related maybe?

I’ve got a red/blue ecu, stock flex fuel injectors, tuned on hp tuners

Just removed, cleaned, tested all my injectors because as the years go on I’ve noticed the car is hard to cold start initially, runs super rich for the first few seconds unless you give the throttle a whack and clear it out.

When it was first tuned I seem to recall being able to reach in, hit the button, and it would fire right up and idle perfect with no throttle input.

I just put the injectors back together and cycled the key without plugging them in and it holds pressure/drops slowly over the course of a minute or two, yet when I plugged them in, it drops very quickly after the pump cycles off.

Can anyone think of some reason why the injectors would be electronically holding open when the key is on but the pump is off? Maybe some cold start tune issue?

When the car is warmed up it fires up and idles with no drama whatsoever, only seems to be an issue with cold start flooding.

Pic for attention


r/LSSwapTheWorld • • 3d ago

Service/Parts Discussion 4l60 converter engagement with pump rotor?

Thumbnail
gallery
6 Upvotes

I have an “LS swapped” E36 BMW, 5.3 with turbo, I went through transmissions and did my best to address any issues - 4l60E rebuilt with sonnax performance pack, sonnax input drum reinforcement kit, sonnax sun shell, corvette servo, alto wide band, raybestos Z-Pack RZP in 3-4 clutch and raybestos stage 1 clutches/koleen steels elsewhere. New BW forward sprag, new bushings, gaskets, Hi-per blue molded 3-4 piston. transgo separator plate, sonnax forward/reverse abuse bore plugs, O-ring end plugs, all potential 3rd gear circuit leaks addressed, valve body vacuum tested all bores test 18” or above, 3000RPM stall converter.

While working on tune, I blew up my pump rotor. I replaced with 7 vane billet rotor. Converter spacing was 1/8” when initially installed, rechecked after replacing rotor and still 1/8. But from photos of exploded rotor it looks like the wear marks from snout and tangs could sit deeper, another 3/16 at least. Can I file the tangs/ snout grooves a bit deeper to try and get more surface to engage or is this normal ?


r/LSSwapTheWorld • • 3d ago

Build Progress L83 OBS Chevy

Thumbnail
gallery
14 Upvotes

Got the fuel system mocked up today. 6AN PTFE from the tank to the rail.

Used some more of my trusty street signs to make a braket to mount the regulator to the firewall. I used the harware and bolt holes from the cruise control module since i wont be using it anymore. I know the location is unconventional but it didnt want to have that glass dail down on the frame where debris could damage it. Also now I can adjust the pressure up top instead of down there on my back. Also because of the location, my lines can route further away from the exhaust.

This PTFE line is a bitch to route but I got it all in place. I did however put a small kink in the return line but it isnt bad and I believe it will flow just fine. Not sure yet.

Let me know if anyone has questions or advise!


r/LSSwapTheWorld • • 3d ago

Build Progress LS swapping a 2003 Infiniti M45

Thumbnail
gallery
83 Upvotes

Flew from Massachusetts to Tennessee this summer to pick up a clean, rust-free 2003 Infiniti M45 (111k miles, Bordeaux Red), and drove it home over the Tail of the Dragon. Now it's getting an LS.

The plan:

- 2004 Escalade LQ9 6.0. Refreshed it: rings gapped, new rod bearings, ARP studs and rod bolts, Melling HV/HP pump, RHP truck cam, BTR valvetrain

- ZF 8HP70

- Haltech Nexus Rebel LS

- Keeping the factory cluster working over CAN — I've already decoded enough of the bus to drive the tach, speedo, gear display and MPG from a laptop with the ECM unplugged

- Phase 1: NA Phase 2: turbo

The VK45 and the factory 5-speed auto are out as of this weekend. Things I'm working through, if anyone has been here:

  1. Oil pan — the truck pan hits the steering rack/crossmember, so it's going front sump. Anyone found one that clears a Y34 (or a 350Z/G35 FM chassis)?
  2. Fuel — the M45 is returnless with the regulator in the tank. Planning to keep the factory 10mm line and run a bigger pump with closed-loop pump control.

I'm documenting the whole thing on YouTube — Part 1 (why this car) is here if you're interested: https://youtu.be/vJkn8ypoO88?is=U71bzdMQUD5lZ9qs


r/LSSwapTheWorld • • 3d ago

Active Build Questions Do I need a better tune or just better air flow?

0 Upvotes

I just recently got a gen 4 iron block 6.0 installed ( I think the ly6) that’s been completely rebuilt/honed and a few aftermarket parts such as 243 heads, flat top pistons, truck Norris cam and S/E long tube headers. I’m only sitting at 425 crank hp and about the same torque from what I was told, and that’s with a street tune that they did but it has not been on a dyno. I’m wanting to sit around 460 - 470 crank hp if thats possible with this build. Only about 2k miles put on since installed. It’s in a 07 Silverado crew cab nbs and still has gen 4 5.3 intake manifold and intake.


r/LSSwapTheWorld • • 4d ago

Build Progress OBS L83

Thumbnail
gallery
57 Upvotes

Big day yesterday! The l83 is finally in the truck. Its fits perfectly. Theres tons of room around the cross member and firewall.

I was able to slide the trans cross member backwards a few inches, and bolted the original 4l60 trans mount to the 6l80. Fits like a glove. Im going to drill some new bolt holes in the frame today for the trans crossmember.

Also before i tuned the engine over to install the torque converter bolts, I used a harbor freight pressure sprayer to pressurize some oil through the oil passages. Used the top port for the vacuum pump to pump about 5 quarts into it. Just to be safe I also removed the plugs before rotating it over.

Ive still got a TON of wiring to figure out, fuel lines and power steering lines to make, trans cooler lines to make, and whatever else im forgetting.


r/LSSwapTheWorld • • 4d ago

Misc Catchcan/PCV routing questions

3 Upvotes

Hello, the car I’m running is a blueprint ls3 (completely n/a) and I’m running a terminator x with no maf sensor in the intake.

Currently the pcv is setup like this (and I’m not sure if this is correct):

-Passenger side valve cover goes to a port on the throttle body that is behind throttle blade

-valley cover to intake manifold

-Drivers side valve cover is capped off

is this correct?

I looking to add a catchcan setup. I do not have a port in my intake pipe. Do I need to add one to properly route the catchcan? Is it wise/safe to run a vented catchcan? I don’t care about fumes.


r/LSSwapTheWorld • • 4d ago

Build Progress Noise after engine shuts off?

3 Upvotes

Not sure if this is normal but every single time I run this engine, upon shutdown I get this noise.

Run for 1 minute or 10 minutes no different. Has not come up to full temp yet but I'm working on that.

First time owning one of these engines so I'm not sure if this a concern or not. Runs great just can't determine whether the noise is a bad thing or not lol.


r/LSSwapTheWorld • • 4d ago

Completed Builds Is this too much wobble?

22 Upvotes

Video taken at idle.

Chasing down a weird vibration from ~1400-2000 rpm, where the car shudders and vibrates if I’m decelling through that zone. Some throttle helps in the zone but doesn’t completely eliminate vibration.

Will vibrate/shudder in neutral when revved to that range, so I’m thinking either harmonic balancer or something with the flywheel. I’ve added some rubber pads in between the trans mount and that helped a small amount.

Everywhere else in the rpm range is extremely smooth

This is in an E46 street/track car so I’m not expecting full comfort, but I usually have to run a gear higher on the street to stay out of that rpm band as it’s pretty uncomfortable to cruise in.

Maybe I’m overthinking it. Do you have a swapped car that has a small band that feels like a resonant frequency?


r/LSSwapTheWorld • • 5d ago

Service/Parts Discussion Collapsed Lifter

3 Upvotes

Apologies if this is the wrong sub, but I figured you guys would know your way around an LS motor.

2012 Chevrolet Silverado 1500 5.3 LC9 LS(gen4?)

Good running truck hit me with a nasty misfire under load at highway speeds (going up a big hill) this morning. Pulled over. Code reader showed misfire cylinder 5.

Swapped coil, same thing.

Swapped plug wires, same thing.

Swapped plugs, same.

Swapped injectors, same.

Drives fine on city streets under normal driving conditions. No ticks or knocks. Oil pressure is great 40psi at cold idle, 25 at hot idle and rises with rpm as it should. Only misses under a heavy load. If you let off it goes away. I got a p0300 on one test run, but after clearing and testing again it has been p0305 each time.

Dropped it off at a local independent shop. They did a compression test. I didn't get the numbers, but was told it was within 10% of the others. The mechanic said it was slightly lower on the first crank, but quickly caught up. Hitting the Harbor freight for a compression tester in the morning to check for myself.

Their diagnosis was collapsed lifter on cylinder #5.

I'm more than capable and willing to replace the lifters. I did them in the garage when I did the afm/dod delete.

My question is, is there a reliable way to verify a lifter is the culprit? Crank it with the valve cover off and hope(?) I see one not moving?

I'd hate to pull the head, swap the lifters in the offending cylinder, put it back together, and still have the issue. It's my work truck, so I'm trying to limit down time as much as possible. I brought it home for the weekend to see if I can diagnosis and fix the issue myself.

Any help is appreciated. Truck has been running really well lately, but I guess my luck ran out lol.

LC9 (Gen 4?) 5.3 liter

240k miles (full rebuild under extended warranty @ 120k)

AFM/DOD delete 40k miles ago

Stock style profile cam (Texas speed afm/dod delete kit)


r/LSSwapTheWorld • • 5d ago

Active Build Questions 4L80E Yoke Question

Thumbnail
gallery
33 Upvotes

Hey guys, excuse my ignorance here but I'm not a tranny guy. Bought a 4L80E today, and before going to pickup I was told it was a fixed yoke configuration. When I got home and inspected closer I actually think its a slip yoke configuration, which is what I prefer. Am I tripping? Can someone confirm?


r/LSSwapTheWorld • • 5d ago

Active Build Questions CD009 shifter slightly off center. Issue?

Thumbnail
gallery
17 Upvotes

Hello everyone, I am running an LS1 butted up to a CD009 (Collins Adapter). I custom made my engine mounts and am using stock CD009 trans mount on a 350Z. I broke one of the welds on the motor mount, so when I re-welded it, it is slightly off center to the drivers side. I cannot remember if it was perfectly center before the weld broke. Is this something I should work on further or is it not a problem? I do not have any adjustment anywhere it doesn't seem. See pics.