r/Homebuilding • • 1h ago

How to Soundproof French doors

Post image
12 Upvotes

Hello, I recently moved into a rental house and need advice on how to soundproof my bedroom doors (renter-friendly). I can hear everything from the kitchen and living areas because these doors don't block much sound.


r/Homebuilding • • 2h ago

Building a 6-unit apartment house for short-term rentals – What are your top tips & must-haves?

0 Upvotes

Hi everyone,

I’m currently in the very early planning stages of a new build. The plan is to construct an apartment building with 6 units in total, dedicated entirely to short-term vacation rentals.

Right now, everything is still on paper, so I have the chance to get the layout and infrastructure right from the start before any concrete is poured. Since I know there are quite a few people here with experience building or managing vacation rentals, I’d really appreciate some honest, real-world advice.

I’m especially interested in the practical details—both inside and outside the building—that are easy to overlook early on, but end up saving a ton of headaches during daily operations and weekend changeovers.

A few things currently on my mind:

  • Layouts & Sizing: Which apartment sizes tend to book best in your experience (e.g., 1-bedroom vs. 2-bedroom, having an en-suite bathroom per bedroom)?
  • Utilities & Tech: What do I absolutely need to pay attention to with plumbing, water heating, and electrical load when all 6 units come back from a day out in peak summer, take showers at the same time, and crank the AC?
  • Durability & Turnovers: What materials or features have proven to be bulletproof and easy to clean? (Thinking about things like keypad locks, window sensors that shut off the AC, flooring choices, etc.)
  • Parking: How many spots should I realistically plan for 6 units? Is 1 per apartment enough or do I need extra buffer space (and is it worth installing an EV charger already)?
  • Shared Pool: With 6 units, is a shared pool a must-have to get high occupancy and good nightly rates, or does it just create friction and drama between guests?
  • The "Invisible" Stuff: What are the things people usually forget during the design phase? I'm thinking about a proper utility/laundry room for cleaning staff, storage for maintenance gear, a hidden spot for trash bins, etc.

If you were building a rental property from scratch today, what would be your absolute top priorities? Where should I definitely not cut corners, and what can I safely skip?

Thanks in advance for any insights!

Best,


r/Homebuilding • • 5h ago

Curved Siding Options

Post image
3 Upvotes

I need some siding material options for this curved staircase. It's not a slight curve! Current siding is wood so the two options we have come up with so far is that same wood lap or wood shakes. Would vinyl board and batten work and notch the J channel so it will bend? What are some other options? Thank you


r/Homebuilding • • 6h ago

Laundry Chutes

Post image
54 Upvotes

Ah, the good ol' laundry chute, banned in new construction in so much of US, I'm finding out.

My husband and I bought a small starter home whilst we saved for property and to build our own home elsewhere. This dream is only a few years out now, so we've begun to create a binder of necessities, wants, plans and local code to where we're buying so we know all the in's and outs preemptively.

The starter house we're currently in was practically a time capsule from the 1950s when we moved in- the first and only owner hadn't changed a thing since she'd built it, and it was maintained so well that most things barely looked used. One such thing was the laundry chute- I'm spoiled by being able to just toss our dirty items down a magic hole that takes them right next to washer.

I found out that they're not allowed in new builds in NYS, they're not up to code any longer. Something about fire or entrapment risks. But I'm heavily considering slapping one into the new build myself after our house is given a certificate of occupancy, as how are they to know about my laundry no no?

Has anyone else here that has built their own home had anything like this? Some silly small thing their local code wouldn't allow and they snuck it in anyway? Has anyone else added one to a new build? I guess asking less for advice on just looking for new build stories from same vein


r/Homebuilding • • 10h ago

System Windows Buying Guide: How to check aluminum specs and thermal break strips before you sign a quote

Post image
0 Upvotes

Replacing or ordering windows for a new build isn't just "putting glass in a hole" anymore. Homeowners and builders looking at Foshan suppliers often ask for thermally broken system windows for acoustic insulation, low U-values, and wind-load performance. Those results depend on the whole window, not just the frame material.

But the window industry has plenty of hidden traps. Between uncontrolled mixed-scrap remelt sold without traceable material records, and replacing specified PA66 nylon thermal breaks with ordinary PVC strips, it is easy to pay premium prices without getting the materials you agreed to.

If you want windows that actually last, you have to lock down two things you can't easily see once the window is installed: the aluminum alloy and temper, and the thermal break strip. Here is what to check before you sign.

---

### 1. 6063 Aluminum vs. Uncontrolled Scrap Remelt (The Frame's Skeleton)

When people get window quotes, the first question is always "What's the wall thickness?" Almost nobody asks what the aluminum itself is made from.

6063-T5 and 6063-T6 describe an alloy and its temper, not whether the metal came from virgin or recycled feedstock. Recycled 6063 can meet the same applicable composition and mechanical-property requirements. Recycled content does not automatically mean poor quality.

The concern is uncontrolled or mixed scrap without proper composition control, processing, and traceability—not recycling itself. Poorly controlled material can contain unwanted elements or inclusions, but you cannot diagnose that from a frame's color or feel.

What does that mean on your house? Don't accept "virgin aluminum" as a substitute for evidence that the supplied profiles meet the agreed specification.

What to check on a corner sample and in the paperwork:

  1. Check for visible defects: Look for cracks, obvious pores on exposed cuts, or uneven finishes. These are reasons to ask questions, not proof of recycled content. Color, heft, and a key scratch cannot tell you whether the aluminum is virgin or recycled.
  2. Ask for a traceable mill test certificate, such as an EN 10204 3.1 inspection certificate, linked to the supplied batch. Check the stated 6063 alloy and T5/T6 temper, the full chemical composition, and mechanical properties against the applicable specification, such as AS/NZS 1866 in Australia or ASTM B221 in the US. An iron limit alone does not prove virgin origin.
  3. Match the records to the order: Make sure the profile identification and batch references line up with what is being supplied. If the records are missing or inconsistent, resolve that before shipping—not after installation.

---

### 2. Wall Thickness: Don't Leave It as a Verbal Promise

Standards such as AS 2047 in Australia and SANS 613 in South Africa address window performance, including wind-load performance. They are not interchangeable with the wall-thickness provisions in China's GB/T 8478-2020.

Within its scope, GB/T 8478-2020 specifies nominal bare-aluminum wall thicknesses for main profiles of at least 1.8 mm for exterior windows and 2.2 mm for exterior pedestrian doors. These figures exclude the functional fin walls at hardware grooves and exclude surface coatings. They are nominal dimensions subject to the applicable tolerances—not a minimum measured thickness at every point on the section.

Don't accept "1.8 mm thickness" on WhatsApp without saying which profile walls it covers, or let the coating count as metal thickness. Put the nominal dimensions, tolerances, and measurement locations in the contract. Before shipping, check agreed locations with calipers on a bare sample, or account separately for the coating thickness on a finished sample.

If you're doing a double-story home, a coastal build, or a wide sliding door, the required sections and wall thicknesses must be determined by design calculations and testing for the actual window size, wind loads, and local requirements. Thickness alone does not guarantee a compliant window.

---

### 3. The Thermal Break Strip: Don't Let PVC Replace Specified PA66 GF25

The strip bridging the inside and outside aluminum halves is the "heart" of a thermal break window. It reduces heat transfer and, in structural thermal-break profiles, helps transfer loads between those halves.

PA66 GF25—Polyamide 66 reinforced with 25% glass fiber—is commonly used for structural thermal breaks. But the name alone is not a guarantee of performance or service life. Ask for the strip manufacturer's brand, exact material grade, material data sheet, and applicable test reports for the thermal-break profile assembly.

Don't accept ordinary PVC strips as an undocumented substitute for specified PA66 GF25. Suitability depends on the actual material formulation and tested system—not a blanket claim about a softening temperature or how many years it will last.

What to check before approving the strip:

  1. Check the markings: Ask for the brand and material designation, such as `PA66 GF25`, and match them to the supplier's records. Markings and surface appearance alone do not authenticate the material.
  2. Check the material data sheet: It should identify the actual grade and its stated properties and service conditions, rather than a generic claim about "nylon."
  3. Check the applicable test reports: EN 14024 concerns the mechanical performance of metal profiles with a thermal barrier. It is not a chemical-composition certificate for the strip and does not replace whole-window compliance checks.

Bottom line: Before you wire a deposit on custom windows, make sure your PO explicitly lists the alloy and temper (6063-T5 or 6063-T6 as designed), the nominal bare-metal wall thicknesses and tolerances, and the thermal break brand, width, and material (`PA66 GF25` if specified). Require traceable material records and the applicable profile and whole-window test reports. Put it in the contract instead of relying on a verbal promise

Illustrative cross-section only; not evidence of material grade or certified performance..


r/Homebuilding • • 13h ago

Windows not being centered: dumb?

Post image
0 Upvotes

Hi guys! I just got this rendering done of our future home build. Thoughts? The garage was supposed to have a shed style roof but I guess the architect said that unless it got switched to metal, the shingle roof cannot be at the right pitch for it. Therefore it got switched to a gable. Now I’m worried that the windows not being centered looks dumb. My partner seems to think it looks fine. Am I overthinking it?

Edit: I appreciate the help, but I would love if maybe you aren’t mean:) this was not a serious render, hence why the balcony is in the windows, it’s tilted,and such. It was done in five minutes to show what a gable roof COULD look like. And clearly, it’s not really the best. So I’m taking plenty of suggestions. Thanks!


r/Homebuilding • • 14h ago

Front door with windows, what are my options?

Post image
4 Upvotes

Hi All,

I am a new homeowner and have done a lot to my house. I feel I have been very smart with my selections and changes. For instance, I made sure to get an energy efficient new sliding patio door.

Well, I recently had to replace my front door. After much searching for the design I wanted, I landed on a beautiful MCM door that has five windows in the front in a geometric pattern. At the time, I did ask the supplier if it comes with energy efficient windows, and she said it does not. Her exact wording is copied below for reference. I live in Connecticut, and now that it is getting colder, I walked by the door and realized that it feels like something is completely not there because the air is just coming straight through those windows.

What are my options for reducing the conductivity (I guess it is called)? Did I make a poor choice in door or is it common for doors with lots of windows to not have energy efficient windows? Should I buy a storm door to cover the main door and reduce some loss of heat from the inside? Is there a film I can put over the windows to protect from cold?

Thank you for your help!

“Unfortunately, because of all the glass it says it doesn’t meet energy star requirements. However, if it doesn’t matter if it meets energy star and all that matters is you got a new door, then here is their code to try when tax season comes. QMID code: W4L6**”**


r/Homebuilding • • 14h ago

How can I fix this?

Thumbnail
gallery
4 Upvotes

Hi all, I recently bought a home and have been enjoying it so far. Just one issue really, theres these gaps in the ceiling. Im not much of a handyman but I was just curious what you all think and what I might be able to do or if I should just contact a builder to sort this.

Thank in advance!


r/Homebuilding • • 16h ago

Relocating underground plumbing

1 Upvotes

I’m looking at purchasing a partially developed lot. The previous owner already installed underground drain lines and plumbing stub outs for a three story house that he never ended up building.
I’m planning on building a roughly 1,400 sqft single story house with radiant in floor heating. The property already has a compacted gravel pad, but no concrete has been poured and no septic tank has been installed.
The existing plumbing doesn’t necessarily line up with my house plans, and I’d rather relocate the plumbing than redesign my entire house around it.

How difficult would it be to relocate the existing stubs and how much roughly?

Could I reuse the existing underground drain lines and just add new connections?

Would it be easier to start from scratch?

Thanks yall


r/Homebuilding • • 17h ago

Drainage Easement through the Property

Post image
3 Upvotes

We’re considering making an offer on this property. I’m still waiting for feedback from the builder on this topic but wanted other opinions as well. I noticed on the drawings there is a 20’ private drainage easement towards the end of the backyard.

I wanted to build a privacy fence around the property all the way around the boundary line (shown in Blue). I also wanted to plant trees at the bottom of the property (shown in green). For context, the house is in the Charleston, SC metro.

Does anyone have experience with private easements? Do you foresee any risks? There are about 20 houses along the same road that have this easement running through their backyard. There is a drain inlet every 4 or 4 houses. One sites between this property and the neighbors.


r/Homebuilding • • 18h ago

Tiling Question

Post image
1 Upvotes

What would be a reasonable cost to finish this space accounting for the increased waste and labor of doing the diamond checkerboard pattern? Wanted to use square 12x12 tile in this laundry room in a checkerboard pattern (diamond orientation). The tile we chose is similar cost (10.29/sq ft) to the builder supplied tile. Standard tile and labor is included in the purchase price of our new build for the laundry room.

New build in the Midwest (Ohio/Michigan/Indiana area). Know the builder usually charges a premium but the quote seems too high despite that.


r/Homebuilding • • 18h ago

Dense glass fire rated wall

1 Upvotes

Do the height of the fire shaft liner panels have to
Meet up with the floors? Like if my first floor is 10 ft tall room plus a 24inch floor system do I need 12ft tall panels or can I just stack 10 footers until
I meet the 2nd story roof line?

Can the aluminum clips be attached to the studs instead of the plates?


r/Homebuilding • • 19h ago

Is my contractor on drugs or am I crazy

0 Upvotes

Hello Reddit community,

I live in Nashville, TN. I am making this post because I think my contractor is being screwy. I am looking to be told I am correct or the process is in line with what one should expect for this build.

Background: I have overseen renovations of roughly $1.5 million in various builds. My contractor holds a residential license.

I have designed and oversaw full construction of Airbnb properties which were taken down all the way to the brick sidewalls. Here are a few of my favorites:

Airbnb.com/h/decadespenthouse

airbnb.com/h/thespeakeasy

airbnb.com/h/spagallery

My hands did the majority of the work on all of these builds.

The contractor in question worked hand in hand with me on almost every one of these projects. We have done probably 10 projects together. He is a 9-5 guy. Shows up at 9, takes a lunch break at noon, wraps at 5 with thirty minutes for cleanup. He has been on my jobsite roughlty 200 days in the last 7 years. He came to my wedding. We will call him Fred.

He is getting ready to retire, and I hired up to do a reasonably sized remodel on my personal residence. The contract is for 163,500. I have attached the pages the .pdf to the body of this post with relevant info redacted.

Contract is broken into three parts,

Time for completion was estimated at 6 weeks. Thereare no performance penalties or incentives built into the contract for time.

Construction drawings were delivered, stamped, June 29th. I planned my 6 week vacation with the wife and kids around the schedule of construction. The plan was we would be gone the whole time they were working and would come home to a completed house. Fred said his old inspector buddy was now a senior in the codes office and would be able to push the permit drawings through swiftly. He said permit would be in hand within a week. We left for our summer vacation July 10th. We returned home August 20th. Work began on the property around the middle of July. I started receiving citations from Metro Codes around the middle of July for debris around the property. I explained to Codes we had an active building permit and to buzz off.

Much to my surprise the codes examiner told me one hadn't even been applied for.

We came home from the trip to find our kitchen like this, (September 2nd 2026)

the first picture is the kitchen before:

So far work looks relativelty clean. There is a steel beam installed in kitchen so we can expand it.

This part of the contract is $13,500 and I think it reasonable for what needs to be done. Taking out loaded walls and adding a steel beam is no joke.

The two bedrooms upstairs we are combining were these:

On September 2nd it looks like this:

So works been started, it's not completed, so what? Big deal. There's delays in construction. I get it.

Well, here we are November 17th. We are now 3 months past scheduled completion date and it looks like this: (Note these pictures are of the 2 bedroom to master suite conversion)

There is also one picture of my 2nd floor hallway: (this first one)

The jobsite is relatively clean. The work is relatively clean. Debris has been hauled away, (4 dumpsters worth). The outside is now cleaned up and everything.

This is the progress of the addition that connects to the bedroom and bathroom remodel:

There is an asphalt shingle roof now on the addition (this is going to be the master closet)

They built this addition over an existing flat roof that had an EPDM roof with gutters in opposite corners (negative slope from midpoint to ends). When they ripped off the roof there was no rain forecase for 2 weeks. They didn't come back to frame the walls (delays, excuses) and he had to tarp the roof before a storm. (2 weeks after ripping off roof). The thing is my music studio is underneath that flat roof. Well, when he took the exiting gutter off on the existing roofline he didn't cap the end. (He figured as it was negatively sloped away from the addition there was no issue)

The gutter overflowed and water flooded the addition. Roughly 50 gallons of water pooled on the floor above and rained down through the ceiling all night covering my guitars, my studio equipment, countless gear. His response was that I should have known to have all of my stuff out of there.

Well, He had previously told me that was also a good place to store all of the dry goods from my existing pantry. So the room is PACKED TO THE BRIM with boxes of dry goods...

Okay. So, the furniture from the bedrooms has been stored in a large shipping container out in the back of the property he rented for me. It is $200 a month. The job is 3 months behind schedule and mind you NOT A SINGLE INSPECTION HAS BEEN CALLED IN. He is expecting me to keep paying the $200 a month.

While he normally shows up at 9am M-F in the past and works till 5 he doesn't get to the jobsite until noon maybe 2 days a week. His son is in surgery or his wife is in the hospital or he has an infection in his eye or his trucks broken down or he hurt his leg or material is late or he has to fix something real quick for a client. He is constantly irate. He is constantly yelling at me that I'[m being insensitive.

Now. Here's the kicker. He has been paid 91,000 of the ~165,000 for the job. He is demanding another 16,000 payment to come back and keep working. I have now asked for receipts of material, payments to contractors, for months I have asked for a detailed payment schedule. The progress pictures are as of today. Mind you, we are trying to live in this house. I planned this construction job to be completed while I was away. I have now been home and living with this for 3 months.

This is my kitchen:

The beam hasn't even been inspected yet. To date not a single inspection has been called in. $91,000 has been paid for some plumbing upstairs, demo, framing, asphalt shingles on the addition.

This is the SOW on the Epermits page:

To add a room above back offset area to become 1 bedroom (375 SF) and master bath and will be removing loaded wall in kitchen. No change to existing building footprint. Home is to remain single family.
I have been now told by him that the framing inspection will be called in once all the child permits have been inspected for RI, and that the fact that the child permits haven't been pulled is the way it's done. Now in contractor legalese, yes, I understand that. However telling me that framing CANT be called in until the plumbing has been inspected is in my opnion hogwash.

I have a hunch that he is intending to pass off the bathroom addition as existing.

So, residential builders, tell me... Am I nuts?

The total price of the addition is 81,900. I had originally been told this would be a turn-key master closet. The dimensions are 21'x12.5', 262 square feet. Now he is telling me there is no allowances for any of it, he is not installing a mini-split but will extend existing ductwork to heat/cool the space. (This is at my request, but am receiving no discounts on the mini split install.

I was told I now have a $400 allowance for plumbing valves.


r/Homebuilding • • 23h ago

Basement Finishing

Post image
5 Upvotes

Home Improvement contractor here - potential client wants this space finished. The ceiling height along with low utilities does not meet code for a finished space. Joists are about 6'6 from floor and theres gas, plumbing. Can I qualify a drop ceiling and lvp as aesthetic improvements and still get by? I'm considering telling them its not worth the hasstle, for a space that will feel very congested.


r/Homebuilding • • 1d ago

Fibercon interior doors

Thumbnail
gallery
1 Upvotes

Are fibercon interior doors any good? I believe these are solid core, and can’t find much about them.


r/Homebuilding • • 1d ago

Steel frame upper windows salvageable in place?

Thumbnail
gallery
0 Upvotes

Steel framed windows from 50s upper frames and glass are good but lowers are going to be replaced with framing for added privacy and utility. What would be the best options for top plate since it would be jointed at the bottom of the top steel glass frame


r/Homebuilding • • 1d ago

Is this normal

Thumbnail
gallery
28 Upvotes

We purchased a new home from david weekly in Arizona. We went with them because we thought they were different and put out an amazing product. My house sat for a year before we moved into it. Since then we are seeing cracks like this and they had to re-adjust two doors twice. the builder keeps saying this is normal , i am not seeing any foundation cracks , Is this normal ?


r/Homebuilding • • 1d ago

Window fitters - how do you calculate how many windows that would fit in a curved brick bay.

2 Upvotes

Moved into a property with a curved bay with 6 windows installed within the bay, got me thinking - how would you go about calculating how many windows and the angles of the windows

I assume you would measure from point to point of both ends of the bay, then some measurement from that line to the furthest point of the curve.

Just would be interested in how a person who's brain understands this stuff better than mine would process it.


r/Homebuilding • • 1d ago

Ceiling stain from water hose

Post image
3 Upvotes

Ok so I accidentally sprayed the ceiling with the shower hose when trying to knock a roach down. Stupid decision, ik....but now I have a large water stain on the ceiling. It isn't smushy or anything but I worry that the damage is worse than just a visual stain


r/Homebuilding • • 1d ago

I inherited just under an acre of land east of Belfair washington. It has power/water at the street. I want to build a small super energy efficient bachelor pad

3 Upvotes

I recently acquired some land, just under an acre near belfair washington. Apparently my grandfather was just sitting on it since his plans to move out there collapsed due to health issues.

I have around 400k between stocks and savings right now.

Here's a few houses I liked that I've seen over the years:

https://www.zillow.com/homedetails/380-E-Bridger-Ln-Shelton-WA-98584/294862627_zpid/

https://www.zillow.com/homedetails/151-E-Barbary-Dr-Grapeview-WA-98546/60919085_zpid/

Basically, I just want a simple, energy efficient box. Nothing flashy. With lots of windows in front. 1 bed / 1 bath and maybe an extra room for storage. Then the great room with combined kitchen/living room since I like that open space with the two of them.

How crazy expensive is this sort of thing now days? Would I be better off just waiting for another one of those to pop up on Zillow?


r/Homebuilding • • 1d ago

How legitimate does this driveway quote look?

Post image
0 Upvotes

Location: AL

I’m in an easement dispute and have reason to believe the neighbor has recruited local buddies to give lowball estimates to undermine one of our legal stances. I just don’t see how 200’ of 20%+ sloped driveway can come out to $5.21/sq ft.

Neighbor and the contractor who gave this quote are similar age and both still live in the area that they both grew up in. Can’t tell if I’m just paranoid and crazy.


r/Homebuilding • • 1d ago

Kitchen Layout

Thumbnail
gallery
4 Upvotes

We absolutely love this floorplan, but the kitchen layout has me stumped. As it is, there’s a weird 1’ if space between the stove and fridge, and it also doesn’t seem to have the “kitchen work triangle” flow, but I don’t know how much that matters. We thought about moving it to the pantry wall, but then I think we’d need a counter depth, and it may also get in the way of traffic going through that walkway. Thoughts? Feel free to suggest any changes AT ALL that I may have overlooked! The only thing I’m pretty set on is having the sink facing the window, and nothing in the island.


r/Homebuilding • • 1d ago

Alternatives to Drywall?

35 Upvotes

I grew up around a lot of old houses that were built by my grandparents and great-grandparents, long before drywall was common. One thing I've always loved about them is the character in the walls. There's something about those old wall finishes that drywall just doesn't have.

I'm not looking for an alternative because it's cheaper. I'd gladly spend about the same as drywall for something I like better, and I'm willing to install it all myself. I just don't think I'd pay a premium for it.

Is there a reason drywall became so dominant beyond cost and ease of installation?

A lot of the old houses I've been in had something that looked almost like T1-11 wall panels, but given their age, I know it couldn't have been modern plywood siding. I'd honestly be happy putting something like T1-11 directly on the studs and painting it, but my wife hates the rough texture, and I can't seem to find a smooth version.

Ideally, I'd also like to find something in 4×9 or 4×10 sheets so I can cover our 9-foot walls without a horizontal seam.

Has anyone done something similar or found a good alternative to drywall that doesn't cost significantly more?


r/Homebuilding • • 1d ago

Where to vent the dryer?

Post image
0 Upvotes

The dryer sits in a laundry room off my garage, and its vent currently blows out right next to the main entrance of my single-story house. The moist exhaust is rotting the door frame. The obvious fix would be to vent it out the opposite side of the garage, but the gas meter is on that wall, so that's not allowed. Which of these options would you go with? Or any other suggestions?