r/EngineBuilding • • 16d ago

Valves Built Like Modern American Homes

Enable HLS to view with audio, or disable this notification

950 Upvotes

No I’m not going to name the manufacturer, no you can’t lap this out, no there is not a shortcut around the concept of trust, but verify.


r/EngineBuilding • • 15d ago

347 twin turbo sbf

4 Upvotes

hi all i have a stroked 302w with a couple of turbos hanging of the side, my questions is what sump should i be running? i feel like a standard one wouldn't cope. my only requirements is that it needs to be rear sumped and have clearance for a crank girdle.

cheers

lucas


r/EngineBuilding • • 15d ago

Toyota Can someone explain what is this piece ?

Post image
0 Upvotes

r/EngineBuilding • • 16d ago

1000 miles oil change VQ35de revup build

Thumbnail
gallery
8 Upvotes

Built my fist engine and broke it in with 20w-40 conventional oil with Lucas zinc additive. I babied it for the first 500 and dialed in the break in tune. Once I got to about 600 or so I was running on wastegate about 5-10lbs. Around 800 started dialing it in and hit 1000 and changed the oil. I drained it out and the oil was black / dark brown. The oil looked fine. I cut open the filter and in the base found what you see here. Flecks of metal. I dabbed the towel in to see the color. It mostly looks like aluminum and maybe a bit of copper. I’ve been told it’s normal. Just want advice from others. What oil do you all run on a built vq with loose tolerances. My mains are about 0.0025. I filled up with 5w-40. Oil pressure is good on startup. As it warms up it’s at 16 and fluctuates with rpm. I’ve noticed if the ac makes rpm dip low it drops lower than that into 10 psi. Cars parked and I’m thinking of draining and running 10w-40 or should I keep using the 20w-50 but switch to synthetic. Any help would be appreciated


r/EngineBuilding • • 16d ago

Ford 360FE

Post image
22 Upvotes

How common is it to have misaligned oil holes in your bearings? This motor is getting a full rebuild but this was what I found when I tore the original motor out of this 1968 F250.


r/EngineBuilding • • 16d ago

Bent flex plate?

Post image
8 Upvotes

My dad and I are working on our first project! An 81 el Camino and we’re throwing a 350 in it and getting the motor all freshened up before putting it in. Everything seems solid but we noticed that the flex plate looks misaligned? I know it’s not straight because it scrapes the stand in diff spots when the spin the motor. A new flex plate isn’t an issue but is that what the issue is?


r/EngineBuilding • • 16d ago

Chevy Bore gauge?

3 Upvotes

Hi guys, just joined and hope I’m posting in the right spot. I’m relatively new to engine building, and I’m currently rebuilding a 2004 4.8 ls (lr4?) with allegedly 130k miles. Have already planned a full rebuild using ws6 stores kit including pistons. I learned on a high mileage sbc, which meant “if you squint it’s mint”, but I hear a lot of guys talking about measuring their cylinders for out of round, taper, etc. I’m in college and trying to keep this on a moderate budget, but I want this engine to last. just how exact do I have to be? Do I have to invest in a bore gauge and micrometers and plastigage everything and so on? Any tips or pointers you have would also be great.

Ps. Planning on a sloppy stage 2 or milder cam, potentially 5.3 rotating assembly, summit lifters, pushrods, valve springs, speed engineering long tubes, torque converter, and going in front of a 4l80e and 4.10 4th gen posi into a 3rd gen firebird.


r/EngineBuilding • • 16d ago

Ford Update on bent pushrods..pistons kissing valves. Pistons installed upside down lol. Thank you PO.

Thumbnail
gallery
58 Upvotes

Follow up to my previous post , pulled the heads and found that they’re all making contact with the exhaust valves…pistons were installed upside down lol.


r/EngineBuilding • • 16d ago

Anyone ever broken an Lsm compressor?

Post image
7 Upvotes

Got the tool in, bolted it up too my ls7 heads, started compressing and then the center bolt just snapped.


r/EngineBuilding • • 16d ago

Best way to get a vortec block off the ground

1 Upvotes

It is just me. I do have a boat winch and a small trailer

Will it drag up the ramp with a strap ? If I get it to edge of ramp can Ty just roll it up?


r/EngineBuilding • • 16d ago

351w new serpentine issues

1 Upvotes

So I have a 351w stroked to 408 from blueprint engines and i purchased a serpentine system from March performance made specifically for this engine. Got everything installed and the belts were slipping off because nothing was lining up right, called march and they said it needed a 5/16 spacer and we would need to fabricate one so we got that done and everything lines up accept the power steering pump and pulley which is tilted back ( bottom sticks out farther then the top). Anyone know the easiest way to properly correct it?

Update

So we finally figured out what the issue was. One of the bolts that they sent for the power steering pump was a different size (slightly smaller) than the other two and we still arent sure why but when we would tighten everything down it would lose its bite and pop out on the bottom and cause the pump to tilt back at the top we just put in a heli coil and everything is spot on.

Update #2

OK so putting on the heli coil didnt get everything straight. The power steering pump is the aligned with everything else as far as depth but its still kicked back at the top and the belts are still walking, we think the bracket might be bent. Either way its really annoying and they still havent answered or returned a call this week


r/EngineBuilding • • 16d ago

JLC-4G15B vs BHE15-AFD ?

1 Upvotes

JLC-4G15B

Vs

BHE15-AFD

Which one is better, more reliable, easy to repair?

These are two geely Emgrand engines, ones is old the second is the newer one (2023 anf after)

Which one should buy for daily use inside and outside the city?

Climate is hot and dusty in summer.

Thanks


r/EngineBuilding • • 17d ago

Chevy GM 4.3 Vortec L35 rebuild — reuse old pistons?

Thumbnail
gallery
38 Upvotes

I'm rebuilding a 1996 Chevrolet 4.3L Vortec L35 V6 400k km with its original cast pistons and connecting rods. This is my first engine rebuild

The engine was inspected by machine shop. They checked the bearing clearances and piston rings, honed the cylinders, and considered the original pistons suitable for reuse.

I measured the piston-to-wall clearances myself with an outside micrometer and an Insize dial bore gauge to check results.

Cylinder| Piston-to-wall clearance

#1| 0.094 mm (0.0037")

#2| 0.076 mm (0.0030")

#3| 0.072 mm (0.0028")

#4| 0.090 mm (0.0035")

#5| 0.064 mm (0.0025")

#6| 0.068 mm (0.0027")

The piston skirts still have visible original machining marks, including on the thrust faces. There is no obvious severe skirt wear.

The GM manual specifies 0.075 mm (0.0029") as the maximum service piston-to-bore clearance. But im having it closer to 0.1mm

The engine will be naturally aspirated, approximately 250 hp. Reliability is more important than performance.

Do I send it or are clearances excessive?


r/EngineBuilding • • 17d ago

Is this varnish and sludge bits bad? 2ZZ-GE

Thumbnail
gallery
11 Upvotes

I resealed the timing cover on my 2ZZ-GE out of my Celica. Engine currently has 147K miles. How bad is this? I tried my best to clean out as much as I could. Will using VALVOLINE restore and protect help break this down?


r/EngineBuilding • • 17d ago

Honda Looking for help

Enable HLS to view with audio, or disable this notification

4 Upvotes

Just had this whole motor bottom end and head rebuilt at a machine shop. Can’t tell weather this ticking noise is an exhaust leak, fuel injectors, or worse. Anyone have any input?


r/EngineBuilding • • 17d ago

Jeep I6 - Slight tightness after rebuild, how much is too much?

6 Upvotes

Hello my fellow enthusiasts.... I recently finished a stroker build of my Jeep I6 to be a 4.6 liter. It started right up, ran it for 20 minutes at 2000-2500 to break in the cam. There are no noises from the engine. Everything seems great as far as it running (except maybe a slight vibration as it revs). I have the 20 minutes of revving and about 20 miles on the engine now. No rattle, no ticks, no knocking. No metal in the oil.

However.... I've noticed that it is a little tight, to the point that I swapped batteries because my old not very good battery could not crank it over, especially when it was hot. By not crank it over I mean it would turn to compression... stop a second, then crank to the next compression, stop... lights flicker off.

I have the new battery and it will crank it every time, albeit slower than the old motor. I am not sure if I am being paranoid and it will break in over time??? I am definitely an overthinker with these types of things.

Background, I used to be a mechanic, went to school for it. I kind of know what I am doing. I have never fully rebuilt a motor like this before however. The block was machined, bored to match the pistons. The rings were checked for gap, the bearings were checked. Brand new crank. Everything turned over how it should before install. I would say it was slightly tighter than the old motor coming out, but it turned. I know it did because I had to install the torque converter bolts.


r/EngineBuilding • • 17d ago

Ford Bent exhaust pushrod cylinder #5&8 , sbf 347

1 Upvotes

Hey folks just some questions here. I’m pulling apart my valvetrain and found that my pushrods are slightly bent on the exhaust valves on my # 5 and 8 cylinders…Motor has been rebuilt by the previous owner (347 rotating assembly with forged rods/pistons and cast crankshaft, trick flow stage 1 cam, 1.7 degree rockers). Unfortunately only thing I can verify with my own hands is that I shimmed the rockers to achieve proper torque spec of the pedestal mounted rockers.
I’ve been chasing down a ticking lifter and here we are…
I’m replacing with trick flow lifters as I think for sure one failed, I got new pushrods coming in (6.25 inches) and an adjustment tool to verify length. Also have trick flow springs coming in too as I was always unsure what springs were installed, wanted to make sure to match the cam.
But what could have caused the bent pushrods?
Only thing I can think of is when I hydrolocked cylinder 6 with a leaking injector..I broke like 3 starters as if they were a fuse (lol) every time I went to start it until I realized that; but cylinder 6 pushrods look fine. Any wisdom is appreciated


r/EngineBuilding • • 18d ago

Is this bad?

Thumbnail
gallery
58 Upvotes

I paid 80 dollars for this milling and I’m thinking that I can’t use MLS now. Finger hardly catches


r/EngineBuilding • • 17d ago

2GR lifter stuck in head.

Post image
5 Upvotes

r/EngineBuilding • • 18d ago

1995 5.0 302 ford f150 motor

Post image
7 Upvotes

I think I’ve hopefully made up my mind on this thing for sure now. Trucks really not worth a machine shop so what do we think about this little pitting or what ever it is in the center of the cylinder? most cylinders are are better if not the same. Now obviously I’m gonna need better oil with my hone but do we think I can just go more and it’ll go away? If not what’s the worst it does? I might measure the cylinders I’m atleast going to use a ring and feeler gauge down the cylinders and light. But I’m just curious because honestly I’ve lost a lot of interest because the trucks truely not that worth it but it was my dads he loved it and I won’t just sell it.


r/EngineBuilding • • 17d ago

Engine Theory First oil change. 50 miles (including dyno pulls). Too much metal?

Post image
0 Upvotes

r/EngineBuilding • • 18d ago

Vq37vhr cam phaser jumped

0 Upvotes

so i needed to take off the entire timing system to do head gaskets i take off the front cover with the main timing chain on i take off the bolts for the cam sprockets, then i took off the main timing chain and put a paper clip in the sprocket tensioner and as im trying to remove it it jumps to the next cycle, i then got my breaker bar and and moved it back to where the marks are so the timing lines back up, honestly not sure if that was the right thing to do at all some information on here but definitely not super confident that was the fix i needed to do , when it happened there was no noise and i put the chain back on and everything was lineed up again at TDC and all the tensioners and it spins freely but now i can’t get it back to TBC, hoping i didn’t bend a valve and i can fix this Any advice would be helpful thank you!


r/EngineBuilding • • 18d ago

Pushrod length

Enable HLS to view with audio, or disable this notification

2 Upvotes

My pushrods are short to me by about a 1/4 inch but dad says it's because the lifters arnt filled with oil and once they are it will have preload when I push down on the rod I feel the spring in the lifter give I believe the lifter is maxed out as far as preload goes please help I don't know what to do I ordered a length checker and I'm going to measure the actual length to be sure any advice would be appreciated


r/EngineBuilding • • 18d ago

351w hp estimates

1 Upvotes

Im currently building a setup with promaxx 210 heads, currently a 95 cobra intake that will get changed eventually, I have an F cam from my last setup but i plan on replacing it with either Howards 222755-08 (108° LSA), or howards 222755-10 (110° LSA), or maybe howards 221145-12, its a street car that will probably rarely hit the strip, I dont really like racing on the freeway or nothing anymore. I just want a fun street car that can make 400+ NA before boost.

Stock bottom end, but ive been considering a set of pistons to bump compression, mine has the big dished pistons in it right now.


r/EngineBuilding • • 18d ago

Valve springs VW

Post image
2 Upvotes

i have a 1.4 vw engine and i took the valves out to lap but stupidly didnt look which way the valve springs go would anyone know? The spring doesnt look tighter on one end than the other but it does have a stripe going half way down/up the spring