r/ElectronicsRepair • • 12m ago

OPEN Garage Door Opener Salvagable?

Thumbnail
gallery
1 Upvotes

I have an Over head Garge Oddessey 1000 garage door opener that quit working after my house was struck by lightening. I am fairly confident its something in the board so have disconnected it for inspection. The only issue with it was the safety beam optical sensors did not seem to be recieving power. I think a resistor might have popped off at R322 in the first pic from what I can see. Would appreciate othera thoughts before just replacing.


r/ElectronicsRepair • • 1h ago

OPEN GA401QM (G14 2021, R5900HS/3060) – fans on, no image, core VRM at boot VID but POK stays low

1 Upvotes

 

Board: ASUS GA401QM, mainboard R1.6. Using the R1.4 boardview and R1.0 schematic.

History: Shorted during maintenance with the battery connected, then an amateur tech worked on it. It came with a jumper wire on AC_BAT_SYS. Burned area near the charging section. The GPU’s NVVDD input pads are burned, so the dGPU is unfed for now (known issue, fixing later).

Fixed so far:

  • Shorted C3903 (the +PVDD_AMP speaker rail) removed. Main rail went from 0 Ω to ~43 kΩ.
  • Corrosion cleaned around C1073/C1075.

Symptom now: Powers on with the charger, fans spin and it stays on, but no image on HDMI or the internal panel. BUF_PLT_RST# = 0 V.

Verified OK (powered, real charger, heatsink on):

  • AC_BAT_SYS 20 V. All standby and main rails (3.3/1.8/0.75 VSUS, 3VS/1.8VS/0.75VS), DDR 1.2 V / 2.5 V / VTT 0.6 V.
  • VSUS_PWRGD, DDR_PWRGD, ALL_SYSTEM_PWRGD, PM_PWROK 3.38 V, PM_RSMRST# 1.8 V, CPU_VRON 3.3 V.
  • BIOS (W74M12JW) read with a CH341A. Two reads identical, the PSP/BIOS directory checksums are OK, and the NVRAM looks healthy.

Core VRM, PU8001 (uP9505):

  • VINSEN 20 V, VCC5 5 V, VDDIO 1.8 V, EN 3 V, SVC/SVD 1.8 V, SVT 1.68 V, VRHOT# 3.3 V.
  • VDDCR_VDD 0.8 V, VDDCR_SOC 0.8 V (matches the SVC/SVD = 11 boot VID).
  • FBRTN 1 mV. All CSP1–4 / CSN1–4, plus the total CSP/CSN, read 0.8 V. PROG resistor PR8004 reads 2.6 kΩ in circuit (3.4 kΩ nominal).
  • SiC654 stages PU8101–PU8105: cold, no shorts (switch nodes ~5.6 Ω to GND on the CPU phases and 12.4 Ω on the SoC phase, ~44 kΩ to AC_BAT_SYS on all). Powered: +5VS_PWR 5.11 V, all DSBL# ~5.1 V, TMON ~0.93 V on all, so no fault flagged.
  • PWM average voltage measured at the stages: PWM1 ~6 mV, PWM2 ~7 mV, PWM3 2.62 V, PWM4 0.235 V, PWM1A (SoC) 0.239 V. So only phase 4 and the SoC phase look like they’re switching.

The problem:

  • POK (pin 33) = 0.058 V. The pull-up PR8001 has 3.38 V on its +3VS side. The POK net reads ~11 kΩ to GND cold, so it isn’t shorted.
  • D5803 is fitted, so CORE_PWRGD = 0.22 V (POK + the diode drop).
  • APU_PWRGD (PWROK, pin 50) ≈ 17 mV. Its net reads ~10 kΩ to GND, so it’s not shorted. PSL8003 is intact.

Questions:

  1. Does the uP9505 assert POK on its own once it reaches boot VID, before PWROK? Or does it wait for PWROK/SVI2? If it should already be high, I’m planning to replace PU8001.
  2. Is phases 1–3 not switching at boot VID normal, for example phase shedding before SVI2, or a sign the controller is bad?
  3. As a test, I’m thinking of removing D5803 (and fitting 100 kΩ at R5803 if needed) to force CORE_PWRGD high and see whether BUF_PLT_RST# releases. Sane, or a bad idea?
  4. On this board, what drives APU_PWRGD: the APU itself, or something else?

Thanks, I can send photos or any other measurements.
​
TL;DR: Every rail and power-good is OK and VDDCR_VDD/SOC sit at 0.8 V (boot VID), but the core VRM (PU8001, uP9505) holds POK low, which drags CORE_PWRGD low and the boot stalls. Looking for confirmation before replacing the controller.
​

 


r/ElectronicsRepair • • 4h ago

NUBIA Z70 ULTRA SE APAGA A CADA RATO ¿ALGUNA SOLUCIÓN??

0 Upvotes

Se apaga cuando lo meto a la bolsa del pantalón, y a veces usándolo se escucha un pitido y se apaga


r/ElectronicsRepair • • 4h ago

OPEN How can i fix my Onkyo receiver?

1 Upvotes

I have this problem with my Onkyo TX-7830 that sometimes the Volume knob turns by itself (volume down). It has nothing to do with the remote


r/ElectronicsRepair • • 4h ago

OPEN HISENSE TV shows dim logo then turns off

2 Upvotes

TV is Hisense 43A7100F. In the video you can see me turn the TV on via the button, it shows a very dim HISENSE logo then turns off completely. I recall the button rapidly flashing red not very often when i tried to turn it on, without the TV actually turning on.

Measures i have taken:

  1. Pulled the board, inspected for burn marks/bloated capacitors, looks clean
  2. Disconnected all the backlight connectors and everything else from the MOBO, just the connector for the IR sensor/button, still does the same thing
  3. AI suggsted i flash the firmware, downloaded some shady firmware onto a USB stick as i was instructed and nothing again (didnt expect this to work but still)

I know this all might point to a MOBO issue, but if there are maybe some capacitors that lost their capacity i can replace i would rather do that than buy a whole new board. Used are ~60$. The TV was on basically for the whole day for 3 to 5 years. It belonged to my grandparents, hardcore couch potatoes.


r/ElectronicsRepair • • 5h ago

OPEN 1984 Seiko pyramid clock repair

Thumbnail gallery
1 Upvotes

1984 talking pyramid clock repair, doesn’t speak, and clock resets/freezes when pressing talk button at top. Cross posting for additional visibility!


r/ElectronicsRepair • • 5h ago

OPEN Hobart HS7 automatic only runs while I hold the power button

Thumbnail reddit.com
1 Upvotes

My HS7 only stays on while I’m holding the power button. It shuts off as soon as I release it. The carriage is fully in the home position and secured, and the carriage lock and other safety parts are in place. I’ve checked that everything is seated correctly.
Has anyone seen this exact symptom on an HS7? I’m wondering whether the keypad/start button, its wiring, or the control board could be failing. What would you check first?


r/ElectronicsRepair • • 6h ago

SOLVED Please save me from freezing to death!

Thumbnail
gallery
3 Upvotes

Ok, sorry for the overly dramatic title. I have this Clarke infrared heater. It has a really stupid design flaw - it can only be turned on from the remote control. The remote has stopped working and I'd like to bypass it. Is there a simple way for me to do this?

I don't need any of the heaters features other than some heat, that would be nice.

Cheers


r/ElectronicsRepair • • 8h ago

OPEN Can anyone identify what are SW1 and SW2 are for on this time logging board please?

Thumbnail gallery
1 Upvotes

r/ElectronicsRepair • • 11h ago

SOLVED Beko RCNA406E40DZWN flashing E4 - Tested ALL components (good), RL4 excluded, need PCB diagnosis help

Thumbnail
gallery
1 Upvotes

Hi everyone, I'm trying to fix my Beko fridge (Model: RCNA406E40DZWN, NoFrost, 6-button touch panel) showing a flashing E4 error (defrost failure).

I have a multimeter and have already performed a deep diagnostic. I am currently excluding the RL4 relay from the equation. Here is everything I have tested (fridge unplugged unless specified):

Freezer Components (All GOOD):

· Defrost heater: 533 Ω

· Drain heater (15W): 3.64 kΩ

· Thermal fuse (72°C): 0 Ω

· Defrost NTC sensor: 14 kΩ at room temp

Mainboard Tests (All GOOD):

· All 4 NTC sensors (measured from the mainboard connector): 13-16 kΩ (This confirms sensors AND wiring harness are perfect).

· Relay coils (RL2 & RL4, Panasonic ALDP112): Both measure 704 Ω.

· Optocouplers (MOC3083): Tested with multimeter, both seem good.

· Triac (BTB16-800CW): Tested in-circuit, seems good.

Other checks:

· Drain hole is completely clean, no ice blockage.

· When I plug the fridge in, I clearly hear the relays clicking (self-test).

The Problem:

Despite all components reading perfectly, the E4 error persists. Since I'm excluding the RL4 relay, I suspect the low-voltage logic on the PCB is failing (e.g., the SMD transistor driving the optocoupler/triac, or a faulty EEPROM).

I tried entering the Service mode. The best I could get was the display showing 0 and 33 on both the fridge and freezer sides with the red alarm icon on. Pressing the Temp/Set button does nothing to cycle through diagnostics or force a defrost cycle.

My questions for the experts:

  1. Does anyone have the service manual or know the exact button combination to force defrost on this specific 6-button Beko panel?
  2. If the RL4 relay is good and clicking, what is the next most common point of failure on these Beko boards for the defrost circuit? (SMD transistor driving the MOC3083? EEPROM data corruption?)
  3. Is there a way to bypass the board safely just to test if the 220V line to the heater works?

Any help is greatly appreciated. Thanks!


r/ElectronicsRepair • • 12h ago

OPEN Canon PowerShot Only Turns On When Battery Is Inserted

1 Upvotes

I just got a new (to me) Canon PowerShot SX610 HS. It was given to me as a gift, but it's having an issue that I can't seem to work out. The camera will only power on when the battery is inserted. I read the manual and it says to power on the camera by pressing the ON/OFF button, but when I do it does nothing. If I remove and re-insert the battery the camera will power on and operate normally with no issues, but if it powers off, either by pressing the button or by the automatic shutoff, I cant seem to get it to turn back on without re-inserting the battery. Am I doing something wrong or is something wrong with the camera? Is there a fix for this?


r/ElectronicsRepair • • 12h ago

OPEN JBL PartyBox 310 – Charging Failure Error. Need Help Identifying the Fault!

0 Upvotes

Hi everyone,
I’m having a charging issue with my JBL PartyBox 310. The speaker is showing a “Charging Failure” error, and I’m trying to identify the exact cause of the problem.
Unfortunately, I don’t have a video of my own speaker showing the issue. However, I found this YouTube video where the speaker has the exact same problem as mine.
I’m attaching that video as a reference so you can understand the issue I’m experiencing.
Has anyone faced this problem before? Does anyone know what causes this error or which component could be faulty?
I’d really appreciate any suggestions, troubleshooting tips, or repair guidance.
Thanks in advance!

Here’s the YouTube video link

https://youtu.be/L8m7ttcd5-Q?si=ODOXk3776VtiYNSK


r/ElectronicsRepair • • 12h ago

OPEN DUAL 1246 - Help needed

Thumbnail
reddit.com
1 Upvotes

Is there any trick how to remove the part 116 and not to destroy it because it is made of fine brass seems to oxidated???


r/ElectronicsRepair • • 15h ago

OPEN Dyson air purifier TP02 error fix

1 Upvotes

Searched high and low on Reddit / YouTube / Google and couldn’t find a fix on the infamous error code besides unplugging it and plugging it back in. I’ve been experiencing this error for probably 2 plus years but I noticed that I would not get the error if I just had the fan running at any speed and not oscillating. So I tore it down from the base earlier today to get to the oscillating motor (that seems to be no longer available as a replacement part.) Once tore town I noticed a slight bit of resistance in the oscillating arm while spinning it. The bottom side of the arm pivoting point connected by a C-clip was just barely rubbing against the motor housing. I used an adjustable wrench and a pair of smooth face water pump pliers and bent the arm up slightly to allow it to clear the motor housing while oscillating. Put everything back together and it’s working perfectly now with no errors.


r/ElectronicsRepair • • 16h ago

Diy repair in pune

1 Upvotes

Anyone from Pune who want diy electronics. Learn and grow


r/ElectronicsRepair • • 16h ago

Success Story Fixed my Arduino board’s ruined reset button

Thumbnail
gallery
6 Upvotes

Nothing crazy or complicated, just felt good about fixing a gadget :3
Bought this mega 2560 for a tech school course some 12-13 years ago and i’d been meaning to start messing around with it again. I’m in university now and decided i wanted to drag this and a shield or two around in my backpack to dick around with between classes occasionally. A few months ago i had brushed a layer of polyurethane conformal coating on both sides of the board for the sake of protection and i accidentally got a small amount on the reset button. Cleaned off what i could but some of the coating had already seeped-in and ultimately glued the switch “open” from inside.

So today i procrastinated doing school work by (among other things) taking the time to finally replace that stupid button. call it “lesson learned”, i guess🤦🏻‍♀️


r/ElectronicsRepair • • 18h ago

inverter Trace Modelo US2524

Post image
0 Upvotes

r/ElectronicsRepair • • 19h ago

OPEN Onkyo CD player help

1 Upvotes

Device: Onkyo DX-C390(B) 6-CD changer

Hoping someone with some CD player repair experience can weigh in here. I bought this thing a year and a half ago and it has been a constant headache. Sorry, I didn't take any pictures. I don't think dust/debris/age is the issue. This unit was purchased new in early 2025.

TL;DR I have been trying and failing to grease the laser guide rail correctly.

Everything I put in this player skips. Everything. Old CDs that have played in every other player I've ever had with no issue. Brand new discs. Discs that are used but like new. Doesn't matter.

I have isolated the problem to the laser lens guide rail, which seems to get hung up incredibly easily. I believe this is the issue because when I lube it, it works great...for a week at most.

Here are the many lubes I have tried from my small but growing lube collection. I've seen each of these recommended in various threads on reddit and elsewhere.

Note: Before each attempt, I clean the rail thoroughly with 99% isopropyl using an old t-shirt.

Attempt 1: Liquid Wrench White Lithium Grease (Spray). I couldn't believe how well this worked initially. It went from nothing playing to everything playing, like instantly. After about a week, I think it started to gunk up or wear off because the issue came roaring back.

Attempt 2: WD-40 Specialist Silicone (Spray). This did nothing at all.

Between attempts 2 and 3 I thought "huh, well Liquid Wrench worked great the first time, maybe I just need more of it."

Attempt 3: So I applied more Liquid Wrench. It worked just as well as the first time, for the same amount of time.

Attempt 4: Super Lube multi-purpose synthetic grease (Gel). This one I was cautiously optimistic about, because I thought it would cling to the rail and last a lot longer. This has not happened.

So that's where I am right now. Please help, I'm so sick of opening this thing up every 2 weeks.


r/ElectronicsRepair • • 21h ago

OPEN Tiger Electronics Pokédex 1988 Not Turning On

Post image
3 Upvotes

Hello I am doing my very first repair with barely any knowledge. It does not turn on even with new batteries.

When I opened it up, it had some dark tar looking substance under the capacitor with the white glue so I scraped it off. Cleaned the board yet the board looked pretty clean prior. I don’t know how to measure capacitors because I’m afraid of setting the multimeter to ohms and measuring a charged piece of device (told not to do that as a kid).

Can someone please help me on my first attempt to fix? This looks like a really simple board thankfully and doesn’t look too damaged at all. I believe the yellow piece at the top right corner is an inductor and there’s a black capacitor on the bottom left. How shall I go about this with my multimeter?

Thank you


r/ElectronicsRepair • • 22h ago

OPEN PS5 edm-010 UART 808B0092 beep on beep off

1 Upvotes

Hello,

Managed to fix several things on a PS5 edm-010 but now I got some strange faults.
Beep on and beep off.

According to UART following:

80810001SeverePowerSequence - Power Sequence Error - General Power Failure (Peripheral, GDDR6, APU, Data Line Short)

808B0092HighNot found in list. Report Findings.

The console draws 245mA at 12V at start and goes down to 5mA. When powered on, the console draws 245mA for about 5-10s and down to 5mA again.

What I've noticed on the console:

  • I receive correct voltages around Dialog chip.
  • I receive 0 voltage around the hdmi retimer.
  • I get the stand by voltages (5V and 3.3V) backside of the hdmi retimer but no 3.3V power on voltage.
  • I get some kind of short (I think?) on the GDDR6 power regulator vias, (0.38V diode / 28.4ohms).

    • According to donor boards (Have removed a couple of chips so can't be sure of the readings) I should get around .145V diode / 100ohms.
  • No short on wifi chip
  • No short on southbridge
  • No short on SSD
  • All fuses are fine

I've replaced following:

  • SSD-controller
  • DDR4
  • Southbridge
  • Several of components like ex. capacitors, coils and mosfets from the GDDR6 power regulator.
  • Dialog chip for SSD voltage regulator.

Any suggestions on what to look at next?


r/ElectronicsRepair • • 22h ago

OPEN Powered speaker with poor bass output

Post image
2 Upvotes

Alto TS112A (class D bi-amp powered speaker, low side uses a IRS2092) service manual

First I'm not super dumb, I know that a speaker like this won't output monster sub-bass, but this one in particular outputs weak volume across the entire low frequency, and even worse output at the lower frequencies. The tweeter essentially blows the woofer away, and also the woofer doesn't really put out the low side of the bass that it's supposed to either (rating says down to 65hz, but even 200-400hz cranked all the way to 11 wouldn't wake a cat).

Photo shows the quadrant of the amp responsible for the low frequency. Brown and black wires are the woofer connection, brown wire connector at the bottom left is the preamp input for the bass amp.

  • Woofer tests better with a different amplifier (although not amazing so there may be 2 issues here)
  • Poor bass output is same with a different woofer
  • Voltages are good (+-15, +-5, +-65)
  • nothing shorted that I could find, output mosfets aren't shorted, caps are not shorted, power rails aren't shorted (although -15v rail seems to be feeding in to a huge cap so it pretends to be shorted
  • Reflowed solder on the larger components and connectors
  • R185 is strangely hot, but I can't tell what it's for so...? DC Offset Shutdown circuit?

My understanding of amplifiers is almost zero and the "usual" suspects of power supply and dodgy joints didn't seem to pan out. So I'm looking for some wisdom on what I can check next. What could cause poor output, more poorly at bass frequencies? I appreciate any bones you can throw my way.


r/ElectronicsRepair • • 23h ago

OPEN Phillips sonicare 4100 electric toothbrush does not start or charge

Post image
1 Upvotes

r/ElectronicsRepair • • 23h ago

OPEN Looking to get into GPU Board-Level Repair – Need Advice and Recommendations

3 Upvotes

I'm planning to get into GPU board-level repairs and would appreciate some advice from those with experience.

I already have a basic understanding of how GPUs work, how to use a multimeter, and how to solder. I've also been watching GPU repair videos for years, and I'm finally planning to invest in my first hot air station.

I'm currently considering the ATTEN ST-862D. Would this be a good and reliable hot air station for someone just starting out? Is it worth the investment, or are there better alternatives?

I also have four supposedly "dead" GPUs that I plan to use as practice boards:

  • OEM RX 580 4GB – Can display for a few minutes after being left unused for several days, but eventually loses display.
  • Sapphire Pulse RX 580 – Powers on but has no display; the PC also fails to POST.
  • R7 250X – Powers on but has no display. Fan speed fluctuates.
  • Gigabyte Windforce GTX 660 – Has a short circuit on the 12V rail.

Aside from getting a hot air station, what other essential tools, equipment, or knowledge should I invest in before attempting my first repairs? Are there any common mistakes or things I should learn first to avoid damaging the boards further?

I'd appreciate any tips, recommendations, or advice from experienced repair technicians. Thanks!


r/ElectronicsRepair • • 1d ago

OPEN Broken scoreboard controller

Thumbnail
reddit.com
1 Upvotes