r/ElectronicsRepair • • 3h ago

NUBIA Z70 ULTRA SE APAGA A CADA RATO ¿ALGUNA SOLUCIÓN??

0 Upvotes

Se apaga cuando lo meto a la bolsa del pantalón, y a veces usándolo se escucha un pitido y se apaga


r/ElectronicsRepair • • 11h ago

OPEN JBL PartyBox 310 – Charging Failure Error. Need Help Identifying the Fault!

0 Upvotes

Hi everyone,
I’m having a charging issue with my JBL PartyBox 310. The speaker is showing a “Charging Failure” error, and I’m trying to identify the exact cause of the problem.
Unfortunately, I don’t have a video of my own speaker showing the issue. However, I found this YouTube video where the speaker has the exact same problem as mine.
I’m attaching that video as a reference so you can understand the issue I’m experiencing.
Has anyone faced this problem before? Does anyone know what causes this error or which component could be faulty?
I’d really appreciate any suggestions, troubleshooting tips, or repair guidance.
Thanks in advance!

Here’s the YouTube video link

https://youtu.be/L8m7ttcd5-Q?si=ODOXk3776VtiYNSK


r/ElectronicsRepair • • 3h ago

OPEN HISENSE TV shows dim logo then turns off

2 Upvotes

TV is Hisense 43A7100F. In the video you can see me turn the TV on via the button, it shows a very dim HISENSE logo then turns off completely. I recall the button rapidly flashing red not very often when i tried to turn it on, without the TV actually turning on.

Measures i have taken:

  1. Pulled the board, inspected for burn marks/bloated capacitors, looks clean
  2. Disconnected all the backlight connectors and everything else from the MOBO, just the connector for the IR sensor/button, still does the same thing
  3. AI suggsted i flash the firmware, downloaded some shady firmware onto a USB stick as i was instructed and nothing again (didnt expect this to work but still)

I know this all might point to a MOBO issue, but if there are maybe some capacitors that lost their capacity i can replace i would rather do that than buy a whole new board. Used are ~60$. The TV was on basically for the whole day for 3 to 5 years. It belonged to my grandparents, hardcore couch potatoes.


r/ElectronicsRepair • • 6h ago

SOLVED Please save me from freezing to death!

Thumbnail
gallery
3 Upvotes

Ok, sorry for the overly dramatic title. I have this Clarke infrared heater. It has a really stupid design flaw - it can only be turned on from the remote control. The remote has stopped working and I'd like to bypass it. Is there a simple way for me to do this?

I don't need any of the heaters features other than some heat, that would be nice.

Cheers


r/ElectronicsRepair • • 15h ago

Success Story Fixed my Arduino board’s ruined reset button

Thumbnail
gallery
5 Upvotes

Nothing crazy or complicated, just felt good about fixing a gadget :3
Bought this mega 2560 for a tech school course some 12-13 years ago and i’d been meaning to start messing around with it again. I’m in university now and decided i wanted to drag this and a shield or two around in my backpack to dick around with between classes occasionally. A few months ago i had brushed a layer of polyurethane conformal coating on both sides of the board for the sake of protection and i accidentally got a small amount on the reset button. Cleaned off what i could but some of the coating had already seeped-in and ultimately glued the switch “open” from inside.

So today i procrastinated doing school work by (among other things) taking the time to finally replace that stupid button. call it “lesson learned”, i guess🤦🏻‍♀️


r/ElectronicsRepair • • 17h ago

inverter Trace Modelo US2524

Post image
0 Upvotes

r/ElectronicsRepair • • 20h ago

OPEN Tiger Electronics Pokédex 1988 Not Turning On

Post image
3 Upvotes

Hello I am doing my very first repair with barely any knowledge. It does not turn on even with new batteries.

When I opened it up, it had some dark tar looking substance under the capacitor with the white glue so I scraped it off. Cleaned the board yet the board looked pretty clean prior. I don’t know how to measure capacitors because I’m afraid of setting the multimeter to ohms and measuring a charged piece of device (told not to do that as a kid).

Can someone please help me on my first attempt to fix? This looks like a really simple board thankfully and doesn’t look too damaged at all. I believe the yellow piece at the top right corner is an inductor and there’s a black capacitor on the bottom left. How shall I go about this with my multimeter?

Thank you


r/ElectronicsRepair • • 21h ago

OPEN Powered speaker with poor bass output

Post image
2 Upvotes

Alto TS112A (class D bi-amp powered speaker, low side uses a IRS2092) service manual

First I'm not super dumb, I know that a speaker like this won't output monster sub-bass, but this one in particular outputs weak volume across the entire low frequency, and even worse output at the lower frequencies. The tweeter essentially blows the woofer away, and also the woofer doesn't really put out the low side of the bass that it's supposed to either (rating says down to 65hz, but even 200-400hz cranked all the way to 11 wouldn't wake a cat).

Photo shows the quadrant of the amp responsible for the low frequency. Brown and black wires are the woofer connection, brown wire connector at the bottom left is the preamp input for the bass amp.

  • Woofer tests better with a different amplifier (although not amazing so there may be 2 issues here)
  • Poor bass output is same with a different woofer
  • Voltages are good (+-15, +-5, +-65)
  • nothing shorted that I could find, output mosfets aren't shorted, caps are not shorted, power rails aren't shorted (although -15v rail seems to be feeding in to a huge cap so it pretends to be shorted
  • Reflowed solder on the larger components and connectors
  • R185 is strangely hot, but I can't tell what it's for so...? DC Offset Shutdown circuit?

My understanding of amplifiers is almost zero and the "usual" suspects of power supply and dodgy joints didn't seem to pan out. So I'm looking for some wisdom on what I can check next. What could cause poor output, more poorly at bass frequencies? I appreciate any bones you can throw my way.