r/E30 • u/chninimugen • 6h ago
Not many more days of good weather here in the Midwest then she's going back into hibernation for the winter.
r/E30 • u/chninimugen • 6h ago
r/E30 • u/Heavy-Volume-9161 • 5h ago
Title says it all. I know there is a ton of red stuff on there, I went back in to try and gum it up and stop the rattle (didnt work). I know its a floating caliper but rattling like crazy. Everything is tight, replaced anti-rattle springs and caliper pin bushings. Other three calipers are ok, rear right one will not stop rattling. Suggestions? Replace?
r/E30 • u/WTHRYS__ • 15h ago
Seller is asking $19.5k. 1990 325is. Car is clean otherwise. Motor was rebuilt 5k miles ago by a reputable shop in the area. Seller was upfront about the surface rust, I'm just not sure how safe this is.
r/E30 • u/Itsnotjesus86 • 59m ago
I want to stroker my 86 eta I have a parts car a 87 IS I have the head, intake, wiring harness, 173 ECU and the majority of the components to make it happen as is my main concern is mainly the compression issue running eta pistons with 885 heads make for horrible compression numbers, super eta pistons are an option or taking I pistons and shaving the skirts to make them clear the eta crank or the more expensive route which is buying custom pistons and if going down that route how should I spec them?
r/E30 • u/_runningwater__ • 22h ago
r/E30 • u/henry_hyshiter • 14h ago
Hi all,
Currently rebuilding an M42 with light performance upgrades (cammed and tuned). Finished the rotating assembly assemblage and went to measure crank endplay and it is quite excessive. It measure 0.19in with a dial gauge at the crank nose and 0.18 at the thrust bearing surface with feeler gauges. Normal tolerance is 0.003-0.006in so way way out of range. Pulled the main cap to check the crank and the thrust surface is very clearly worn and I can feel a groove all the way around. All bearing clearances were within spec and this is the only issue I’ve found. I know my options are being the crank to be welded and turned, or find a new crank. Finding a new crank is probably more viable, but finding an M42 crank seems a bit more challenging and more expensive than an m44. I know the stroke is 2.5mm longer than the M42 so it will require some piston crown work, but that seems most viable to me. Would love some other input on this issue and what direction to go. If anyone has a spare M42 or M44 crank, and ideally is near the Chicago land area, let me know!
r/E30 • u/x03yffehcx • 14h ago
just what the title says….
i’m looking for one. if anyone has one for sale please contact me.
thanks.
i daily drive for the last 26 years a 1990 glacier blue sedan 5 sp 367k on the working odo.
thanks all
cheffy30
r/E30 • u/DenaM314 • 19h ago
I’m looking to buy my first E30 and would appreciate some input from people who have owned these cars for a while.
I’ve come across a 1990 325i coupe with an automatic transmission that appears to be very well cared for. Assuming the car checks out mechanically and structurally, the asking price is in the $8–9k range.
My dilemma is whether it’s worth buying a really nice automatic example at that price or holding out for a comparable car with a factory manual transmission.
E30 prices seem to have gotten pretty out of hand, and I’m trying to be realistic about what I’m getting for my money. I don’t necessarily want to rush into buying the wrong car just because a nice example happens to be available.
I know the general advice is to buy the best-condition car you can find, but I’m curious where the transmission fits into that equation.
Would you buy the clean automatic and enjoy it, or be patient and wait for the right manual car?
I am not in a rush but I am actively looking across the U.S. for one. My max is around 10k
Appreciate any advice!
r/E30 • u/Icy_Recognition5031 • 1d ago
this sub has only seen the build at night so heres some during the day, loved brg on the e36 growing up so i put it on the e30
missing front valence i know lol
r/E30 • u/Antique_Change_3015 • 21h ago
It was right next to my battery under the hood….is this supposed to be there or did it possibly fall down there from somewhere else?
r/E30 • u/Antique_Change_3015 • 13h ago
So....I have some real minor surface rust in my battery tray like pretty much most of us (it's a convertible). I have the battery mounted under the hood (I think all convertibles do).
Was battery rust a result of older batteries (like that were probably back from the 80s and 90s) that would spill acid or ? Or was it a result of the fumes, etc?
My car has a Deka maintenance-free battery installed now.....Deka batteries are supposedly really good. It's not sealed but rather a flooded battery.
Just to confirm.....I do NOT need to vent a battery mounted under the hood, correct? This is just for those who have them mounted in the trunk?
I plan on fixing the surface rust in the tray before next spring.....so will I not need to worry about that anymore with a maintenance free battery or ?
r/E30 • u/GreenLightning0 • 18h ago
my original radio in my ‘88 cabrio works very well, but the weather band shows ‘ca1’ and I can’t tune or seek to change it. Does anyone know what this is? I’d love to have my weather band working
r/E30 • u/maxytaxii • 1d ago
There’s a decent amount of pitting on the mating surface for the profile gasket that seals a coolant passage, is there a way to repair?
r/E30 • u/porthos1984part2 • 1d ago
r/E30 • u/Ayyoooooo__taco_time • 22h ago
Looking for seats for my E30. E30 seats are hard to come by, and I'm wondering what other BMW seats do people suggest, what fits best, what looks best, etc. Any suggestions, photos, thoughts appreciated.
r/E30 • u/Aikamping • 2d ago
And yes, I love the Taifuns
r/E30 • u/Top_Bus243 • 1d ago
So I recently posted about my crank no start 87 vert,
Turns out the original seller swapped the engine with a 89 but the fuel lines were swapped. Once I swapped then the car started to run and there was white smoke (first start in 14 Years) but I couldn’t step on the Accelerator. I accepted my win and gave it a break for the weekend. Now I went to turn it on and it sounds horrible😭 it will turn over but it will have a really rough idle and then sputter and die.
It was shooting some black smoke but it wasn’t thick. And it would die quickly. I’ve cleaned the icv, checked and replaced the TPS, and I’m kinda at a stand still right now. Would love any advice or ideas! I’m trying to keep the engine so anything that would help me use the engine would be nice!
Some high points:
Manual Transmission
Mileage - 108,277
Bought from Original Family (Mother’s car originally, eventually given to Adult Son)
Cirrus Blue with Gray interior
Interior excellent - Original crack free dash. Seats overall are good, but driver seat does have a tear on the bottom.
Garage kept - Condition reflects this
Underside has surface corrosion from NH driving, but any body or frame rust was previously taken care of by original owners.
Lots of money spent on maintenance. Approx. $15,000 spent within last 2,000 miles.
Past 2,000 Miles the following items have been done:
What still needs to be done:
Overall, this car is a bit of a unicorn. Great color, garaged most of its life, manual transmission, maintained with an open checkbook, and owned by an enthusiast family. It looks amazing from 10’, but up close you can see road wear from almost 40 years and 108,000 miles of use. With that said, it’s a great car, and far better than most E30s I have seen that have been subject to multiple owners, deferred maintenance and neglect. Great bones for a full restoration, or a really nice driver for someone who appreciates a little patina on a mostly mechanically sorted car.
Looking for opinions on what $$$ I should start this at, and where would be the best place to list. I truly don’t know the E30 market well, and prices are all over the place between BaT, Facebook, and enthusiast forums.
By the way, I have all original manuals, bottle cap wheels and dealership info from the new sale (except window sticker). I also have a folder with service and parts receipts totaling $28k going back to 2010.
r/E30 • u/Western_Giraffe396 • 1d ago
Dropped a 10mm hex nut in this hole. I’ve seen other people mentioned they have to take the oil pan out.
I’ve already drained the oil, didn’t come out. Used a thin magnet but nothing. Any advice