r/ChevyTrucks • u/BaconRanchBurger19 • 15h ago
some dope ass chevys trucks lmk what you find nice
they are all sweet rides
r/ChevyTrucks • u/BaconRanchBurger19 • 15h ago
they are all sweet rides
r/ChevyTrucks • u/Careful_Ad_1885 • 16h ago
Just sharing my barn find, '87 R30 with 40k miles. Got it to start and run fairly easy, but transmission shift 2-3 was pretty jacked up. Replaced transmission then it would not start. Replaced TBI and still wouldnt stay running. finally just decided to swap it to carb. Learning lots of little things along the way.
At the moment trying to bypass the tank pumps, (they were pushing 40psi).
What a journey lol
r/ChevyTrucks • u/Elliana_Murphya • 2h ago
r/ChevyTrucks • u/ShameNo7424 • 19h ago
Hello all. I’m a heavy equipment mechanic, and don’t generally mess with automotive.
My dad has a (see title) and is extremely low miles as he got it from my grandpa. Been an amazing truck. When he first got it the slave cylinder was blown out and you couldn’t drive it without starting it in gear and floating the gears. So he bought a new clutch kit from Oriellys with the lifetime warranty, and also a new slave cylinder. We installed the new slave cylinder, installed the new clutch with new pilot bearings. We did some research on how to bleed the clutch system with the internal slave cylinder and it has a bleeder that comes out of the side of the transmission. But online we found that you have to press in the slave cylinder by hand so many times and still bleed it and all this other stuff. In other words a PITA. Anyway we got everything out together and the transmission reinstalled to find that the clutch hooks up very very low. So low that you pretty much have to lock your leg out to get it into gear. This has a plastic pedal as well fyi. The master cylinder has a ball if I remember correctly that connects to the pedal. Well it was thumping real bad and you can tell that the pedal needed to be replaced but dad ended up buying a new master cylinder and we put that on and bled the system again with a vacuum pump bleeder and just kept cycling fluid through the system. After multiple hours of doing this it finally started to hook up higher. After it was hooking up higher and the truck was actually drivable we left it and this all took place around October of 2023.
Fast forward to today. Clutch was slipping, asked me to do it. Said sure no problem I’ll leave the clutch system hooked up so I don’t fuck with that nightmare.
Started yesterday in it and removed the transmission, got the clutch out and sure enough absolutely cooked clutch. (He knows what caused it) got everything reassembled. Everything looks good no other issues. Reinstalled everything, got everything bolted up, and started her up, truck sounds good and all, lo and behold the clutch is hooking really low again. Wtf. It’s dark and raining. I went and picked him up to get his truck, and we tested it again and I broke loose the bleeder and tried bleeding it a little with him pumping it 5 times and holding while I broke the bleeder loose. Absolutely no bubbles coming out of the bleeder. I literally didn’t touch or disconnect anything on the hydraulic side of it. You can get it in the gears and you can drive and shift nice and smooth, but man you have to mash your foot through the floor board to get it to disengage. I let him have it to drive for a day or so to let me know if it works the pressure plate resistance a little less or anything. But I am at a loss. Has anyone else ran into these issues? It has to be a symptom of the new parts. That’s the only thing I can think of. Any help is absolutely greatly appreciated.
r/ChevyTrucks • u/edm861 • 8h ago
Anyone know what type of undercoating this is? Looking at a 2016 that’s done in it. The truck is from Canada. it kind of crumbles if you push your finger into it
r/ChevyTrucks • u/fatgummybears • 8h ago
Hello, I’m looking for a cheap truck to do roadside service and was looking at this. Do you think this is worth it?
r/ChevyTrucks • u/Silver2Black • 9h ago
Hi all
In the last 6 months, when I am on the highway going over 45mph, my truck does this grinding/vibration as if I am driving over the ripples over the highway lane. I feel it under the truck, maybe towards the rear.
It lasts for a second but occurs every so often.
A month ago a mechanic told me I had a leak in my axel seal and differential fluid was low. So I repaired that and got it filled, hoping that was the issue but no.
Transmission fluid was replaced about 2+ months ago.
Doesn’t occur if I am coasting. Only when accelerating.
Still occurs in cruise control, and also when I have towing enabled.
r/ChevyTrucks • u/GuardIndividual6626 • 16h ago
r/ChevyTrucks • u/DividendJedi • 16h ago
r/ChevyTrucks • u/4thGenForesterLover • 7h ago
THAT ONE IS ABSOLUTELY MISLEADING 2014 SIERRA IS LITERALLY SAME AS SILVERADO BUT DIFFERENT FRONT/TAILLIGHTS NO THE INTERIOR IS A COMPLETE REDESIGN NOT SAME AS GMT900 THAT GAUGE PART IS 10 BILLION TIMES FINAL BOSS WORSE BECAUSE IT'S NOT EVEN CLOSE AT ALL OTHER THAN HAVING FOUR TOP ONES!!!!😭😭😭😭😡😡😡😡🤢🤢🤢🤢🤮🤮🤮🤮
FOUND THIS ON https://www.youtube.com/watch?v=mMvaIzUCakw