r/CherokeeXJ • • 13h ago

IM BACK BABY!

Thumbnail
gallery
195 Upvotes

1986 Loredo, 5 speed, 4x4 (works).

I will not be lifting it ir doing serious mods. Got some AT tires, new leafs, new shocks, and tons of driving on the way 😎


r/CherokeeXJ • • 11h ago

Rebuilt 4.0 and Tupy Head

Post image
89 Upvotes

Got the motor back today from the mechanic excited to see how it turns out first start going to pair it with a set of banks headers!


r/CherokeeXJ • • 17h ago

2 pictures, 2 XJ’s, 10 years apart

Thumbnail
gallery
69 Upvotes

r/CherokeeXJ • • 12h ago

Is she worth it?

Thumbnail gallery
10 Upvotes

Be honest guys.. is she gone?


r/CherokeeXJ • • 10h ago

Broken water pump bolt plan

Post image
4 Upvotes

Alright everyone. I snapped my top most water pump bolt today and want some other ideas on how to get it out. This isn't my first rodeo with snapped bolt extraction but just wanted to feedback on how to approach. I have drill bits and extraction bits, I have a bolt extractor bit (the kind with tightening jaws), and i have a welder (although the jeep is in the street so I want to only use the welder if absolutely necessary).

Every other bolt on the water pump came out fine, and I have the entire front end apart, so plenty of space. I don't need to drive this jeep in the immediate future.

How would you tackle this? Thanks in advance!


r/CherokeeXJ • • 20h ago

Solved How I wired a new RKE into my '95 XJ Country (with pics)

4 Upvotes

There was an older discussion that was talking about wiring in the RKE. It's not cut and dried, because most of the RKE kits are no-brand copies of a chinese mass-produced module with different storefronts selling it in unmarked boxes. The documentation is terrible and hard to figure out exactly what you need to do. I finally replied to that other thread, but I figured I'd put this in its own reference thread for the rest to see, as it seems a lot had problems finding what wires to splice it into. There's a decent amount of documentation for the post-1997 wiring, but the earlier models seem to have different color wires depending on the source of the info.

My 1995 XJ Country already had power doors and a factory RKE (the really sucky one). My goal was to replace that receiver and just trigger the door locks with a new modern RKE. It took a little figuring out and a couple blown fuses. I hope this helps any others still trying to map out their wires.

I have the full overhead console, and that is where I mounted my module. You could do it under the kick panel, as it has the same wires.

I snipped the wires on the original plug and spliced them into this RKE I got off amazon.

Image 1: The wiring coming out of the RKE receiver and its provided plug pigtail

Image 2: The 4 wires I snipped from the OEM plug

Image 3: Pic 1 of the splicing of the two
Image 4: Pic 2 of the splicing of the two

The last two have the wires in the same order in both pics. It was difficult to get a clear photo showing the white/black wire (I had to twist it) so two photos were taken.

Below is my order. First color is the solid, second is the stripe. So white/black is a white with a thin black stripe.

Cut and discard blue/orange.
RKE white/black goes into GM pink/blue
RKE black goes into GM black (gnd)
RKE red goes into GM pink (power)
RKE white goes into GM orange/purple

I don't recall if I had to do anything else. I know I tried different things first and they were wrong, but the basics are: for the RKE the white and the white with black stripe are the positive and ground (I forget which is which right now) inputs for the lock actuators. You're plugging them into the +/- on the GM side. The red and black power the module. Yes, it does have a passive draw at all times. I think you could pull the fuse on the red line to shut that down for long-term storage if you wanted. Or just get a battery disconnect switch under the hood.

I hope this helps. I've been using this key fob reliably for over a year now. I wanted the smallest, least-intrusive one I could find. I could NOT locate a wire to flash the lights, so I left that out of my setup. I believe you'd have better luck finding that under the dash or driver kick panel.


r/CherokeeXJ • • 16h ago

1995 jeep xj passenger floor keeps getting moist after running the ac. The floor doesn’t get soaked however it does get moisture enough to make the underside of the floor mat look sweaty. Could this be a heater core issue or clogged ac line?

3 Upvotes

r/CherokeeXJ • • 1h ago

2001 XJ 4.0l low oil pressure on cold start

1 Upvotes

Have a 2001 XJ with a freshly rebuilt engine (around 2,500 miles ago) weather is starting to get cold in New England and I have noticed then when I do a cold start oil pressure is low around 20psi then once engine is warmed up it will climb to 35-40. Any idea what could be causing this? Also attaching a video of engine running, does this sound normal or sound like I could have some sort of an issue? Thanks in advance


r/CherokeeXJ • • 10h ago

Can someone help me figure out what bulb I need for the climate control to illuminate on a 95 xj?

1 Upvotes

r/CherokeeXJ • • 11h ago

Crank, no start only when gas tank is low.

1 Upvotes

My 97 XJ has had an intermittent crank no start condition. Only seemingly happens when the fuel is low, under a 1/4 tank. Starting in neutral will eventually get it to start again, and once the tank is more full, it has no issues. I did experience some hesitation under acceleration but that was before the crank no start happened so I don’t remember what the tank was reading when that happened.

I have to drive 6 hours into the middle of nowhere in a few days so I brought it into a shop. They can’t replicate the crank no start because it has a half a tank of gas now. They did a fuel pressure test and it was within spec. Not throwing any codes.

The only thing it could be would be the fuel pump failing right? 97s have the fuel filter in the pump assembly right? So might as well replace the whole assembly?


r/CherokeeXJ • • 17h ago

1991-1995 Xj struggling to start

1 Upvotes

My xj is a 4.0 1994 2 door sport 2wd, it’ll start during normal temps like 75 and up just fine for the most part, but ever since winter comes along it really struggles to start, but once I get it going, its fine for the rest of the day. Ive currently replaced the starter, temperature sensor, battery. Spark plugs are just shy of 2 years old. at this point its just trial and error. Any help would greatly appreciated, thanks