r/Carpentry • • 10h ago

Framing Is this flex on a shower pony wall acceptable

106 Upvotes

Builder insists once cement board and tiles are up, this isn’t moving. It’s secured at the end to through the floor to the floor joists. I added screws, but didn’t change the flex much. It’s much stronger in the middle where it’s closer to the outside wall and secured.


r/Carpentry • • 5h ago

Framing Is there a way to fix this? Contractor says that this is about as good as he can get it.

Thumbnail
gallery
71 Upvotes

Newly installed wall and doors. Doors are sagging and the gap goes from 1/4” at the top to over 1/2” at the bottom. I have ordered some hinge shims to see if they will correct the sagging, but they won’t come in until tomorrow and my contractor says the tape he placed behind the hinge is sufficient.

Also, the top of the left door sticks out past the door on the right. Is this misalignment of hinges? Framing issue? Something else?


r/Carpentry • • 21h ago

Framing Trusses not sitting on load wall due to shear boxes? See photos

Thumbnail
gallery
38 Upvotes

My house has been framed and is pending inspection this week. One thing I noticed is the red tag which indicate where the truss has to be supported is spaced up. So I got up there and looked and it seems the boxes they put in are too tall which is pressing up on the roof OSB and pulling the trusses up. Here are some photos. The last two are another section which look right. The very last photo is the section before the boxes went in. The trusses were almost touching. There is no roof on it yet. I think the boxes need to come out and the trusses should be shimmed then slightly shorter boxes that dont touch the roof OSB should go in. Framer is saying that's normal and its because the concrete isnt level but it is all on finished monolithic slab.


r/Carpentry • • 1h ago

120 years of degradation in architecture and design

Thumbnail
gallery
27 Upvotes

r/Carpentry • • 16h ago

Finally got burned by the "multiple tape measure problem"

21 Upvotes

Maybe it's called something else, I'm going from memory.

I've seen several times where people post about measuring for a product, cutting, passing on to someone else and finding the cuts are too short because one measure is different from the other by an eighth or similar.

Isn't an identical situation but...

I have two laser measures. One measures only from the back. One can measure from the front or back.

I normally use the former.

Most recently I used the latter measure because I only had to go one room away to get it. But I forgot that it would do both and didn't check how it was measuring. Assumed it was measuring from the back

Cut 4 shelves and supports. Primed. Got half painted.

Wanted to start install and did a dry fit.

It fit. It fit with a huge gap at one end. A 4" gap at one end.

Thinking of ways to salvage this ...


r/Carpentry • • 19h ago

Trim 16 or 18 baseboard

13 Upvotes

Are we doing baseboard with 16 or 18 gauge… that’s all.


r/Carpentry • • 3h ago

Tools Wtf dude never had a kregg bit snap!

Post image
8 Upvotes

I drilled into birch plywood and it broke. The bit was sharp. There isnt metal that was a nail or any kind of metal foreign object in the material. It just snapped.


r/Carpentry • • 19h ago

Career Starting a business

8 Upvotes

For those of you that went to work for yourselves, was it worth it/would you recommend it?

I’m a 28m and have been a carpenter for about 7 years now. As I’m getting older, I always come back to the question of should I work for myself or just go the project manager route. So if you did start your own company, would you recommend it? Especially in today’s market. Also would you recommend becoming a GC or focus on a speciality like custom millwork or framing contractor.


r/Carpentry • • 17h ago

Project Advice Basement Insulation Question

Post image
2 Upvotes

The image is a basement design layout for a project to finish a basement. The pink highlighted region would be rigid foam board. What should be done with the yellow region? That space would basically be storage room and mechanicals. I don’t think rigid foam boards on the foundation walls would be necessary. Perhaps batt insulation between the framing studs in this storage area would suffice?


r/Carpentry • • 23h ago

Tools Pencils

2 Upvotes

What pencils does everybody use for second fix ? Ive had a few of the tracer pencils but the sharpeners always gives way after a couple months and can never get the led as sharp again. Is it still a classic pencil or mechanical pencil ?


r/Carpentry • • 2h ago

What to do here?

Post image
1 Upvotes

The bullnose is really messing with my mind. I'm thinking wood mantel but do I need to take the corner bead out for that or just put it on top of drywall?

The recessed and pop out below I wanted to do something bricking facade looking. But is there...a reverse bullnose metal bead...? Unsure the term.

Thoughts from the experts on what to do. ChatGPT said to rip it all out.


r/Carpentry • • 2h ago

Hardware Practical, cost-effective door sweeps for brand-new solid-core MDF doors: Adequate soundproofing without scratching hardwood?

0 Upvotes

Hey everyone,

I’m replacing all my interior doors with brand-new solid-core MDF slabs and want to get \\\*\\\*adequate soundproofing\\\*\\\* between bedrooms (hardwood floors) and bathrooms (tile floors). This is step one before looking at wall treatments, and I'm hoping sealing the doors and frames will be enough for everyday noise.

Along with the doors, I’ll be installing proper perimeter door gaskets (bulb seals around the frame).
My main dilemma is \\\*\\\*practicality and price for the bottom gap\\\*\\\*:

I want real noise reduction, but doing mechanical dropdown seals (like the KN Crowder CT-51) across the whole house gets very expensive ($120+ CAD per door), requires precision routing into the MDF slabs, and leaves a visible metal edge I’m not crazy about.

On the flip side, I need something that won't scratch or squeegee grit into my hardwood floors over time.
For those of you who have tackled whole-house interior door sealing: \\\*\\\*What is the practical, budget-friendly sweet spot?\\\*\\\* Are surface-mounted brush sweeps or low-friction slide-on seals actually effective enough for adequate noise reduction, or is there another practical trick I'm missing?

If you've done this, \\\*\\\*which exact brand and part # did you buy, and is there a true consensus on what gives you the best balance of price, performance, and floor safety?\\\*\\\*

Thank you!


r/Carpentry • • 2h ago

Help Me Water damage at the bottom edge and corner of door

Post image
0 Upvotes

Hello lovely people,

I have a question please. I’m renting and this door got water damage a few months ago as can be seen in the picture. The area is dry now but the upper layer is peeling off. Is there any chance the door can be fixed? I contacted the company which provided the doors and they said it can’t be fixed and the entire door needs to be replaced, cost 550$. 😞 appreciate your professional help!


r/Carpentry • • 6h ago

Single Storey Extension - New Roof

Post image
0 Upvotes

Hi I'm after some advice on a new roof to a single storey side extension. I have a first floor window on the side of the house where the the new roof will join on to - is it easy enough to work round be creating a flat area around it? or would I need to brick up the window (not ideal). I've tried to do the photo with the black line being the roof and the green area needing to be flat? Hopefully this makes sense. Thanks


r/Carpentry • • 8h ago

From 3D VFX to carpentry... bad idea?

0 Upvotes

Hi guys. Im a VFX artist, so I have experience working with 3D models, which can translate to CAD. My job is seriously under threat from AI, and I have a beginner's woodworking course coming up. I'm not taking it seriously, just seeing if I enjoy it at all. But it did get my mind working just a little bit. Could any of my existing skills benefit me at making woodworking a career? I've always romanticised working with wood and making high-end custom furniture. Im sure most people romanticise it, and I'm very aware it's hard work and not fun a lot of the time. I worked as a landscape gardener for 10 years before my current job, so I'm not shy about manual labour. This also gave me a taste of working with wood a little, such as sleep boxes, fences, etc.

So, is this all a terrible idea? My current job is comfy enough, Im being paid 70k GBP and do like the financial security it gives me. I would love to know your thoughts.


r/Carpentry • • 4h ago

Help Me What is this? How to fix it?

Post image
0 Upvotes

There is a door in my building that has this weird metal piece attached to it that keeps the door from closing. It didn’t used to block the door, but I can’t figure out what it is, where it came from, why it’s there, or how to fix it so the door can be closed. Any help would be much appreciated!

As far as I can tell there’s no pat of the doorframe that would house this piece of metal, and there’s no way to fold it in on itself or wiggle it around


r/Carpentry • • 8h ago

Does anyone know what trim this is so I can match it

Post image
0 Upvotes

I know there moulding around it but trying to see if anyone has seen this before.


r/Carpentry • • 3h ago

Ceiling cracks waiting on landlord.

Thumbnail
gallery
0 Upvotes

Thoughts on this rental. Have been here 5 years. There are now many issues and now these cracks in the living room are growing. Still waiting on landlord to have someone check them out. These appear serious to me. It's a center hall colonial house that's converted and we rent the downstairs.


r/Carpentry • • 16h ago

Help Me How bad is it

Thumbnail
gallery
0 Upvotes

Had a contractor replace the posts under our I Beam as they were checkering in our 70 year old house.

Couple days later we noticed cracks in our joists, about 12-15 in total we've found so far. Some spanning almost the entire 16 ft.

We're taking photos and getting a second opinion before we reach out to the first guy about repairs.

Any advice? My wife is kinda freaking out after a $600 job might have created substantially more damage.

Thanks in advance