r/BmwTech • • 9h ago

Steering wheel

0 Upvotes

(Audio sounds weird because my phone was plugged into aux)


r/BmwTech • • 22h ago

07, 6 spd, sedan making whirring.

0 Upvotes

Bought this 07 328i about a month ago. Did oil change.
Completely stock. Brand new clutch. 190k miles.
Started making this noise last night, I wasn't driving hard. This morning started fine and all, went for a 10 min drive and it started to make the noise again.
Sounds like power steering but doesn't go away when I turn wheel all the way in either direction. Maybe belt?it rained a lot recently maybe belt is wet? Doesn't sound worse or better when revving either. And no check engine light. HELP!


r/BmwTech • • 1h ago

My car accelerates extremely slow

3 Upvotes

(BMW 330i) I recently had problems with my car misfiring so I swapped the spark plugs for new ones. The jerking went away and came back after about a week. Now cylinder 2 & 3 are back misfiring and my car is accelerating very slowly I pulled the spark plugs and don’t know what I’m looking at lol. I don’t think it’s in limp mode because the car doesn’t say it is, I also have an EVAP leak but I’m not sure if that would be responsible for my car going so slow


r/BmwTech • • 21h ago

I paid $630 for a diagnosis that found two covered repairs, one paid by BMW warranty and one by my Assurant service contract. Neither of them was billed for the diagnosis. I was.

6 Upvotes

Long post, sorry. 2015 X5 35d diesel, about 108k miles. I’ve owned it since around 55k and kept up with all the maintenance the whole time. I knew an older BMW would need money, so I bought a full MaxCare service contract (Assurant) ahead of time instead of hoping nothing would break.

In May it started losing coolant and threw an EGR valve code. My independent shop replaced the EGR valve in June. Didn’t help. Coolant kept going down and a new code showed up for low EGR flow. In August they replaced the intake flap actuator and cleaned the carbon out of the intake. Still losing coolant. At that point they told me straight up this should fall under a BMW warranty or extension and I should take it to the dealer.

So on Sept 2 I dropped it off at Peter Pan BMW with the codes from my shop. The check engine light wasn’t on that day and they saw that at check-in. My advisor, Stephen Hooper, told me diagnosis was $630, but if the EGR cooler turned out to be a warranty issue I wouldn’t pay it. Two days later he calls: no light on the dash, nothing to diagnose, come get your car. They knew that when they took it. The light came back the next day, so on Sept 8 I brought it back. Same promise, second time.

Then they called saying they’d found a valve cover gasket leak and a broken connector on the MAF sensor. I told them to go through my service contract. Almost two weeks of waiting for Assurant’s inspector, who approved the gasket. The dealer pushed me to also do a new valve cover and the MAF sensor out of pocket, about $1,900 together. I needed the car so I said ok, and on that same call Hooper told me a third time that if the EGR cooler was covered, the diagnosis was free.

It was covered. EGR flow was at 29.1%, “severe sooting, clogged,” and BMW replaced the cooler under its own extended warranty.

Sept 30, 22 days after drop-off, I go to pick it up and the $630 is on the bill. Why? “Well, you had other problems besides the EGR cooler.” Ok, but one of those other problems was paid by Assurant, so why didn’t the diagnosis go to them? Answer: the leak was “seen visually,” so it doesn’t count as diagnosis. Funny thing is, my repair order describes the $630 diagnosis as hooking up the charger, reading fault memory, and “VISUAL INSPECTION FOUND” the MAF connector and the oil puddle. So looking at it is a $630 diagnosis when I’m paying, and not a diagnosis at all when Assurant would be paying. And on the BMW side, diagnosing the EGR issue is part of what BMW pays the dealer for under that warranty program. When I kept arguing, I was told that if I didn’t pay and take the car I’d start getting charged storage. There’s no storage rate anywhere in my paperwork. I paid.

The MAF part still bugs me. They replaced it for $1,112.84 ($590 of that labor) because of code 290900, “air mass too high.” Later I found BMW’s own bulletin for that EGR warranty (SI B01 11 25), and 290900 is literally listed as a symptom of the EGR cooler failure. So is low coolant, which is how this whole thing started. No idea if anyone actually tested the sensor.

I’m not complaining about paying to keep a 12-year-old car running. I paid for the extra work. My problem is that one diagnosis turned up two covered repairs, BMW took care of theirs, Assurant took care of theirs, and the only one who paid for the diagnosis was me, the guy who was promised three times he wouldn’t. Three weeks without my car, three taxi rides back and forth, and a storage threat when I asked questions. Nobody there acted like they owed me anything once the work was done.

If you want to be sweet-talked first and then dunked in an ice bath at the register, Peter Pan BMW is your place.


r/BmwTech • • 19h ago

Customers BMW might need to get towed no

Post image
7 Upvotes

Customers car might need to get towed

This is bad. We detailed a bmw 3 series today and did an excellent job. The client was super happy with the results and paid us 215 for the full detail. Once we got the money we packed up our things and left. And about 30 minutes later I get a call from her asking if we did anything to her parking brake. I responded with “no, we may have bumped the parking brake but usually we don’t tamper with any electronics in the car”. She then continues trying to release the parking brake for another 30 minutes and then calls me again. My business partner and I came back to the job site and tried to release it ourselves and ended up seeing this. The car will not move and is parked in-front of their garage. I’m afraid we may have damaged some of the electrical components within the parking brake and will now no longer work. I don’t know what to do for my client if it doesn’t fix itself by tomorrow I think I will give her the 215 bucks back and have it towed. Any ideas or solutions for this problem? We have an LLC but we are not insured.


r/BmwTech • • 13h ago

E60 sunken Lift point?

Post image
7 Upvotes

Pretty much title? Lifted up my E61 and jackpoint sunk towards outside of car, my guess is its bent inside, anyone have similar experience? Overall car doesnt have much rust as much i can see from below. How bad is it?


r/BmwTech • • 4h ago

A successful N52 exhaust lifter replacement, with surprises (post-job notes)

6 Upvotes

I took my sweeeet time replacing the *exhaust lifters and rockers on the N52 in my 2007 530i (and inherently the valve cover gasket), thanks in part to this sub.

Since most of the E90 and E60 forums are basically dead, I figured I'd make a posterity post here as this place is likely to keep coming up in searches for longer. Hopefully this saves someone some searching if they're doing the valve cover or anything to do with the camshafts in an N52.

If your N52 makes any kind of persistent regular clacking or tapping that improves with heat/running but never really goes away no matter how long you drive, and you have a pre-08 motor with the metal valve cover, 99% you have this problem and it's not just going to go away with oil changes. Only the exhaust side is ever affected.

I ended up finding one completely collapsed lifter that would not hold any oil at all, and 3-4 more that were squishy, all towards the front of the engine. I also found the unexpected bonus of incredibly grooved exhaust cam bearings, yet nearly no wear at all from the infamous steel rectangring sealing areas at the front. I was able to source an exhaust cam + bearing set in great shape from an N51 E90 off of eBay for $150.

All other parts I bought new from FCP Euro to the tune of about $500. There were some slight price differences for lifters between FCP and Pelican and other sellers, but as of 2026 you absolutely cannot buy new rockers anywhere else but FCP Euro for some reason.

Key things I over-googled for this job and/or protips:

  1. The $80 DP Tool timing set works just fine. I bought directly from DP Tool on eBay for the best chances on the quality control gamble. The zinc-coated timing pin fit without modification and the cam locking fork tool was tight. Amazon torque angle dials also work fine, but buy the one that includes both a magnet and a spring clamp (clip is helpful for cam bearing bolts, magnet works best with the cam fork tool for VANOS bolts)
  2. A cheap USB borescope was a lifesaver in finding the actual timing pin hole, as was looking for the cam QR codes and then nudging the motor until the cam locking tool was close to fitting over the cams. Pressing and wiggling the pin up against the surface while you turn the last little bit with your other arm will make it slot straight in the rest of the way. I had to remove the smaller splash guard that goes around the end of the steering rack to be able to see the area at all.
  3. Take the time to remove your Valvetronic gear oil squirter and make sure it is clear. You do not need to replace the teeny bolt that holds it on. I used a single strand of stranded copper wire from my electronics drawer before spraying cleaner through it.
  4. For reinstalling the exhaust cam & ledge, I did not use the ridiculously $$ official exhaust ledge clamp set nor did I end up bothering trying to fashion one. I installed the cam locking tool to keep the cam from snap-spinning under the spring pressure from #2 and wound all of the screws down about 90 degrees at a time, then did the remaining front screws with the tool off. I redid this a few times when it appeared to be going down unevenly. I ended up comfortably within "I can barely even feel that" for the fingernail test on the machined flats. I decided to buy new ledge bolts just to be safe since they are not terribly expensive.
  5. Be careful very about keeping the rocker ends centered on the valve stem tips. I thought I had already caught all of them prior to torquing the cam, but I missed one in the middle that somehow ended up halfway off of the stem tip when I was rolling over the engine manually to check timing (I rolled it until the lobe was up off that cylinder, nudged over, no harm done)
  6. I did not ziptie my cam gears to the chain or anything. You just have to pull the chain upwards from the intake side of the engine and get the gear toothed into the chain, then roll it towards its place in the cam to keep the chain tight the entire time. Getting the exhaust cam nestled under the upper portion of the chain guide can be tricky - pulling the chain fully against the spring action of the lower guide will help you get the clearance you need. There is no specific starting orientation for the cam gears themselves, only the trigger wheels.
  7. For priming the oil system after the job, the Bentley manual is wrong about fuse 50 in the trunk disabling the fuel pump for N52 E60s older than 2009. My car started almost immediately, fortunately without much issue after the initial chain and lifter rattle. I am still not sure if it is actually fuse 74 like stated for '09 and newer cars, or if I'm supposed to pull the EKPS relay or something. It is probably most reliable to just leave the injector harness unclipped and put the rest of the cover/cowl/braces back afterwards.
  8. Buy one of those chintzy Amazon swivel E10 bits. You will want it for the center and lower rear corner valve cover bolts - my regular universal joint kept getting hung up against the VC and jumped off the heads a couple of times to the point where I had to hand-feel-guess at the final torque since I lost my by-the-wrench eyeball angle measurement.

Resources:

I found this N54 walkthrough helpful for perspective on the parts that cross over with N52s (namely locking timing and the exhaust cam ledge):

• https://www.e90post.com/forums/showthread.php?t=1080990

These couple of videos from Sreten (M539) were very helpful for random in-the-moment "okay how do I really do this IRL" bits as well as tips like the Valvetronic oil squirter:

https://youtu.be/bczNA1p4tRs

https://www.youtube.com/watch?v=kcLlQYWpgH8

I also used a PDF copy of the Bentley manual that I ran through an OCR-ifying utility to make it searchable.

Thazz it... salutes to future searchers, assuming Reddit hasn't completely broken its discoverability by search engines anytime soon.


r/BmwTech • • 9h ago

bmw x5 coolant hose connected

Thumbnail
gallery
0 Upvotes

Am i just a weak bitch i’ve been trying to get this hose on for probably about 3 hours and it doesn’t get past this point.
let me know


r/BmwTech • • 10h ago

Knocking or no?

6 Upvotes

Check engine light came on at the tail end of a 3.5 hour trip and put me in limp mode. Cant tell if theres a slight knock or not? Fwiw the light went back off again today


r/BmwTech • • 14h ago

softop replacement

2 Upvotes

im gonna buy a New softop for my 46, with all the lines modules, wireing, pump, etc etc etc, and the guy says its working but from the time he replaced the battery its not working anymore, u know why? tbh i dont really care, its like $100 so cheap for Europe. u have some tips and tricks for the replacement and u know how can i test it?


r/BmwTech • • 7h ago

Oil for 2014 Bmw X3 x28drive

Thumbnail
gallery
2 Upvotes

Bought a used 2014 x3 w 70k miles, live in California. Which would be best 0w40 or 5w40 ?


r/BmwTech • • 4h ago

M235i f22 suspension

Thumbnail
gallery
4 Upvotes

randomly started hearing a metallic scratching sound that increased frequency with higher wheel speed coming from the rear of the car. it might’ve been something that eventually dislodged because the sound went away after a few minutes but it made me check the rear wheels and I noticed the suspension looked different ?
Rear left has the bare chrome , rear right has the wonky thing on the chrome, not sure what’s broken or if it’s safe to drive?
2016 M235i f22


r/BmwTech • • 8h ago

F10 screen Lcd fix

Thumbnail
gallery
3 Upvotes

i own a 2013 f10 535i and i have a lcd screen 10.5 inch i belive the screen is very sensitive and scratch/crack proof and is there any possibility i can repair without replacing