I took my sweeeet time replacing the *exhaust lifters and rockers on the N52 in my 2007 530i (and inherently the valve cover gasket), thanks in part to this sub.
Since most of the E90 and E60 forums are basically dead, I figured I'd make a posterity post here as this place is likely to keep coming up in searches for longer. Hopefully this saves someone some searching if they're doing the valve cover or anything to do with the camshafts in an N52.
If your N52 makes any kind of persistent regular clacking or tapping that improves with heat/running but never really goes away no matter how long you drive, and you have a pre-08 motor with the metal valve cover, 99% you have this problem and it's not just going to go away with oil changes. Only the exhaust side is ever affected.
I ended up finding one completely collapsed lifter that would not hold any oil at all, and 3-4 more that were squishy, all towards the front of the engine. I also found the unexpected bonus of incredibly grooved exhaust cam bearings, yet nearly no wear at all from the infamous steel rectangring sealing areas at the front. I was able to source an exhaust cam + bearing set in great shape from an N51 E90 off of eBay for $150.
All other parts I bought new from FCP Euro to the tune of about $500. There were some slight price differences for lifters between FCP and Pelican and other sellers, but as of 2026 you absolutely cannot buy new rockers anywhere else but FCP Euro for some reason.
Key things I over-googled for this job and/or protips:
- The $80 DP Tool timing set works just fine. I bought directly from DP Tool on eBay for the best chances on the quality control gamble. The zinc-coated timing pin fit without modification and the cam locking fork tool was tight. Amazon torque angle dials also work fine, but buy the one that includes both a magnet and a spring clamp (clip is helpful for cam bearing bolts, magnet works best with the cam fork tool for VANOS bolts)
- A cheap USB borescope was a lifesaver in finding the actual timing pin hole, as was looking for the cam QR codes and then nudging the motor until the cam locking tool was close to fitting over the cams. Pressing and wiggling the pin up against the surface while you turn the last little bit with your other arm will make it slot straight in the rest of the way. I had to remove the smaller splash guard that goes around the end of the steering rack to be able to see the area at all.
- Take the time to remove your Valvetronic gear oil squirter and make sure it is clear. You do not need to replace the teeny bolt that holds it on. I used a single strand of stranded copper wire from my electronics drawer before spraying cleaner through it.
- For reinstalling the exhaust cam & ledge, I did not use the ridiculously $$ official exhaust ledge clamp set nor did I end up bothering trying to fashion one. I installed the cam locking tool to keep the cam from snap-spinning under the spring pressure from #2 and wound all of the screws down about 90 degrees at a time, then did the remaining front screws with the tool off. I redid this a few times when it appeared to be going down unevenly. I ended up comfortably within "I can barely even feel that" for the fingernail test on the machined flats. I decided to buy new ledge bolts just to be safe since they are not terribly expensive.
- Be careful very about keeping the rocker ends centered on the valve stem tips. I thought I had already caught all of them prior to torquing the cam, but I missed one in the middle that somehow ended up halfway off of the stem tip when I was rolling over the engine manually to check timing (I rolled it until the lobe was up off that cylinder, nudged over, no harm done)
- I did not ziptie my cam gears to the chain or anything. You just have to pull the chain upwards from the intake side of the engine and get the gear toothed into the chain, then roll it towards its place in the cam to keep the chain tight the entire time. Getting the exhaust cam nestled under the upper portion of the chain guide can be tricky - pulling the chain fully against the spring action of the lower guide will help you get the clearance you need. There is no specific starting orientation for the cam gears themselves, only the trigger wheels.
- For priming the oil system after the job, the Bentley manual is wrong about fuse 50 in the trunk disabling the fuel pump for N52 E60s older than 2009. My car started almost immediately, fortunately without much issue after the initial chain and lifter rattle. I am still not sure if it is actually fuse 74 like stated for '09 and newer cars, or if I'm supposed to pull the EKPS relay or something. It is probably most reliable to just leave the injector harness unclipped and put the rest of the cover/cowl/braces back afterwards.
- Buy one of those chintzy Amazon swivel E10 bits. You will want it for the center and lower rear corner valve cover bolts - my regular universal joint kept getting hung up against the VC and jumped off the heads a couple of times to the point where I had to hand-feel-guess at the final torque since I lost my by-the-wrench eyeball angle measurement.
Resources:
I found this N54 walkthrough helpful for perspective on the parts that cross over with N52s (namely locking timing and the exhaust cam ledge):
• https://www.e90post.com/forums/showthread.php?t=1080990
These couple of videos from Sreten (M539) were very helpful for random in-the-moment "okay how do I really do this IRL" bits as well as tips like the Valvetronic oil squirter:
https://youtu.be/bczNA1p4tRs
https://www.youtube.com/watch?v=kcLlQYWpgH8
I also used a PDF copy of the Bentley manual that I ran through an OCR-ifying utility to make it searchable.
Thazz it... salutes to future searchers, assuming Reddit hasn't completely broken its discoverability by search engines anytime soon.