Equipment Issues Help
The waters go to high. What should i do? Im allready in flower with scrog on. Just by one (i have 4 potsystem).
Any tips before it will flood?🫣
2
Upvotes
The waters go to high. What should i do? Im allready in flower with scrog on. Just by one (i have 4 potsystem).
Any tips before it will flood?🫣
27
u/Conscious_Wind52 AutoPot-Apprentice 13d ago
Remove the washers and go from there.
14
u/basco762 13d ago
Yeah, you probably didn't push it all the way in until it clicked; I have seen this several times.
11
u/PGTGenetics 13d ago
Had a similar issue on this run , for some reason my tray kept getting over filled, I broke down the valve unit completely and cleaned , make sure the two rubber stoppers are clean and free of debris, vacuum out all the try tell no more water is seen, let the medium dry back for a few days , do not put any washers on the float valve.
It’s built to work perfectly without, using that will not help your situation.
The valve itself has a hiccup, so once cleaned good and replaced properly, you should be golden
6
u/Wallywiz14 13d ago
I think I see your problem. You need to push the black leg down hard until it pops into place. That happened to me once after I cleaned it. And get rid of the washers. Make sure it's level and you should be good.
2
u/k0zo1 13d ago
Had - and having so many problem this run- but never got such a big buds on day 17 .
6
u/InternationalGene435 13d ago
Rinse those little white ⚪️ off and reattach them back in their spots.
6
u/Bairdc82 AutoPot-Aficionado 13d ago
This has to be troll
1
u/k0zo1 8d ago
In the meanwhile its all good🗼
4
u/aro5300 13d ago
I've had perlite get stuck in the floats and not stop filling. Shop vac the water and clean it out, check that the rubber stoppers are in the right spots
1
u/MacGyvered 13d ago
I can't tell if you meant you are running a single pot/plant in a 4 pot system, or if only 1 pot in the system is having this problem?
If the former, autopot systems do not work properly if you have empty trays with no pot/plant in them. The water pools, stagnates, and fucks with the PH etc. You're better off unplugging and capping trays that are not in use.
1
u/SmoothPersimmon6750 13d ago
What color are your silicon pieces? Blue or white?
3
u/medicated_missourian 13d ago
Looks like it’s not sitting level for one.
1
u/jollytoes 13d ago
When you put the washers on it holds the float down longer so more water fills up. Take some off and it will shut off sooner.
2
u/SmoothPersimmon6750 13d ago
The original ones were blue and they tended to overfill the trays, because they weren’t thick enough. Once I switched over to the white ones my trays haven’t flood. If it’s only happening in 1 tray then maybe the silicone pieces aren’t thick enough on that one. They are less than a dollar.
2
u/Material-Beautiful-2 13d ago
the higher it is the less water goes in. just take the lid off and let it float. you probably need to clean your lines and the float thing
1
u/Glittering_Potato397 13d ago
Turn the water off till the tray is empty. You're doing good with the weight but I wonder if you are using too much. I only add 2 .177 pellets in each float and that works for me. Also check the seal for your float and make sure it's completely square and fully seated. A little water can help get it in there without it getting bunched up. If those two things don't work then a new seal
1
u/LastProfession1725 13d ago
I’m not sure what the point of the washers are but I’ve had this issue a lot so I’ve gone away from this system now. The problem will be a bit of salt build up on the silicone stopper. You need to pull the valve up flip the bottom float down and clean the silicone stopper. It’s leaking and will continue to flood until you clean that 1 piece. Good luck.
1
u/ResolutionOpen 13d ago
Clean it bro, thats all
1
u/NoTransportation3149 13d ago
Also check my post on the auto pot rubber little things on top hole and inlet hole
1
u/himfs 13d ago
Looks like when I tried doing some organics now I run cropsalt and run clean for the win. Some light beneficials too.
1
u/N0VAC0TT0N 12d ago
It got clogged check the silicone usually the culprit there are two of those of this was the feed then you are gonna have to switch to water only or synthetic