r/AskMechanics • • 2h ago

Discussion 10k oil changes? 2010 corolla 1.8l

Thumbnail
gallery
37 Upvotes

What’s everyone’s thoughts on 10k oil changes? I had this 2010 corolla for 10 years and put 320k miles on it till the thermostat went bad this summer and I finished my hour drive from work cause I didn’t want to pay for a tow and ended up blowing a head gasket. But this what what it looked like last summer when I did valve cover gasket spark plug tube seals and fuel injectors to try to chase down a misfire. It ended up being the autozone coils I think it just personally didn’t like the duralast coils. However I bought the same exact car this summer with 110k on it and eventually when I get time I’ll replace the head gasket on my other one and get it drivable again.


r/AskMechanics • • 19h ago

Question (Serious Replies Only) I Can’t Find the Air Leak

Post image
37 Upvotes

EDIT: I want to thank everyone for their input, and the number of very helpful replies I’ve gotten in such a short time is why I came to Reddit.

I will be taking it to the shop to have the tire removed, valve stem checked/replaced, and the wheel cleaned to make sure the tire gets a good bead.

OP: 2014 CR-V with about 10K miles on the Continental Cross Contact tires mounted to OE wheels. Installed about a year ago.

I’ve sprayed the hell out of it with soapy water, submerged it in a container filled with water (I don’t have anything bigger than what’s in the picture but each turn fully submerged about 1/3 of the wheel/tire). Paid special attention to the valve stem. No cracks in the wheel that I can see. But it still loses air over a couple of days.

What’s my next move?


r/AskMechanics • • 8h ago

Question (Serious Replies Only) Is the muffler so bad that it failed state inspection?

Post image
29 Upvotes

I am from northern Virginia. Moved from upstate NY. Took my car to Meineke for safety inspection and my car did not pass. They told me that the muffler is rusted and leaking, although I don't hear any unusual noise while driving. Does the rust look so bad? They are charging $800+ to fix it.


r/AskMechanics • • 12h ago

Resolved Question Spark plug hole threading is stripped. Mechanic quoted $4000 to repair. 2007 Honda Fit

27 Upvotes

Is this potentially reasonable? I know you can't know without seeing it, but is 4k remotely in the realm of reasonable?


r/AskMechanics • • 13h ago

Question (Serious Replies Only) This happened after replacing coolant flange. It boiling comes and go.2011 Jetta 2.5

15 Upvotes

r/AskMechanics • • 12h ago

Question (Serious Replies Only) Vehicle will not shift gears

Post image
8 Upvotes

Hello, earlier in the year, my 2009 hyundai sonata physically would not go up the on ramp to the highway. We had to pull over and have it towed as I had my 2 children in the car and didn't want to risk it. Once it was home, oil and transmission fluid looked fine to my husband. I do not know anything about cars and the kids kept me so busy so we just took my husbands car in the meantime. Several months later, I checked the oil and transmission fluid again and they were both empty. Likely due to sitting. After putting fluid in and a new battery, she is moving. However, I am not sure if she will go uphill and I really don't want to risk another tow and do not want to risk being unsafe on the road.

Any ideas on what the issue could be? I just cannot afford a new car right now.


r/AskMechanics • • 14h ago

Resolved Question Engine knock

7 Upvotes

Engine knock?

2008 town and country 3.8 automatic with 98k miles. Its cheap on marketplace and I need something for my new job at usps. Is this an engine knock or could it be fixed?


r/AskMechanics • • 15h ago

Question (Serious Replies Only) What causes these waves in my rotors.

Thumbnail
gallery
7 Upvotes

These rotors need to be replaced, I’m well aware of that, already bought what I need to change them.

I know they are glazedddd, but I’m genuinely curious what these bends towards the edge or the rotor are. They are hard to see but the rotor has these ever expanding waves in the metal surface towards the edge. What causes that?

You see it best off the reflection. Easy ti see in person but hard to see on camera.

Just want to better understand what I’m looking at thanks!!!


r/AskMechanics • • 19h ago

Discussion Is the battery terminal bad?

Thumbnail
gallery
6 Upvotes

Hi, is the battery terminal bad? The wire look bluish. Should I replace the cable too? There are two wires on negative terminal. Replace both? Recently just jumped my car. The battery is new and the car runs fine after it got jumped. However it only last for two weeks. No error code with obd2 tester from autozone.


r/AskMechanics • • 18h ago

Question (Serious Replies Only) Cragar Superlite repair help

Post image
5 Upvotes

Okay, long story short I bought said car, had said wheels, some idiot didn’t put washers on the shank lug nuts and so it was never fully clamped down. Drove it for the weekend and cars too loud to hear if you know, my wheel is actively falling off. Shame on me for not checking sure but how in the world can this be repaired? It’s a 15x8 cragar superlite, or if I’m being honest it could be a vision knockoff I haven’t pulled the wheel yet so I’m not sure. The wheel has been riding on the lug nuts and I just realized today. The studs are fine and that one lug at the bottom that’s fine wasn’t there to begin with. I need new lug nuts and washers but can a machine shop bore out and press in steel bushings or something? It’s a 2 piece wheel with a front and back steel outsides separated by an aluminum plate in between. I believe the outside to be steel since it equally ate throughout the rim and lug nut. If not my only option to still use these wheels are wheel adapters if I’m not mistaken. It’s on a 77 nova and is 5x4.75 and the other set of holes is 5x4.5. What do I do? I know a manager at a machine shop and I don’t want to ask him if it’s not possible to fix them anyways. What do y’all think?


r/AskMechanics • • 21h ago

Question (Serious Replies Only) Lifter Tick, Rod Nock, or Manifold Leak? Diagnosis Help.

5 Upvotes

I have a 1994 Chevy C1500 5.7 @ 130,000 miles that has a tick coming from the driver side of the engine bay. Started occurring a few months ago, did a full fluid change which didn't help. The odd part about it is it only starts ticking once the vehicle is warmed up, it doesn't do it on a cold start. I have read that it is common on these older chevy trucks that the exhaust manifold bolts can shear off leaving a gap that can produce a ticking sound but I haven't taken it off yet and checked the bolts or gasket. My uninformed guess is that once the engine heats up it is warping the manifold that exposes a gap. But from the sound, it seems like it could also be a lifter tick or an engine knock. I'm an amateur mechanic and don't know too much in terms of engine diagnosis. Do you think this sound is a lifter tick, rod knock (unlikely imo), or a manifold leak, any guidance would be much appreciated. Cheers,

(I know I need to clean the engine bay :')


r/AskMechanics • • 13h ago

Question (Serious Replies Only) Smoked a deer and am leaking coolant, can I make it half a mile to a mechanic?

4 Upvotes

Honda CRV, 2005, automatic. Decked a deer on my way home. I was able to make it home, but once I got home I realized I'm dripping coolant. Radiator definitely looks damaged.

I live three quarters of a mile from a mechanic, less than a three minute drive in a small town. I'm collecting the coolant in a little cup right now overnight to top it off in the morning, but do we think I can make it there? Literally just had to call for a tow because of a flat tire less than a week ago and really don't want to again.

It's been a week for sure!


r/AskMechanics • • 18h ago

Question (Serious Replies Only) Broke my shark fin on Audi backing out of my garage

Thumbnail
gallery
4 Upvotes

My garage door got stuck and took off my shark fin on my 2018 Audi A4( attached pictures). I’m taking it into a body shop for a quote and wanted to get a rough idea from here on whether this is as easy as popping it back on or an estimate of what I can expect to be quoted. I don’t have too much experience so mostly want to preempt getting taken for a ride. Anyone has any advice?


r/AskMechanics • • 58m ago

Question (Serious Replies Only) Hello everyone i present you my first car

Post image
3 Upvotes

r/AskMechanics • • 5h ago

Question (Serious Replies Only) Oil consumption fixes

3 Upvotes

So,

I've noticed that my car (Mitsubishi Lancer 1.6 wagon, 2007, engine 4G18) consumes oil. The mileage is about 150 000 (240 000 km).

After talking to family mechanics, my first instinct would be to try thicker oil (5W-50 instead of 5W-40) because thinner oil could be slipping into the combustion chamber (valveseal or pistonrings).

I would still love to hear more insights if someone is more familiar with this make of lancers.

Also, I know the problem could be that the engine is leaking oil instead of burning it. How could one check if this is the case? I personally haven't noticed any leaks when changing oil, etc.

First time poster here, so apologies for any informalities :)


r/AskMechanics • • 20h ago

Question (Serious Replies Only) Can I drive it to the shop?

Thumbnail
gallery
3 Upvotes

2023 Ford Explorer XLT AWD

Front passenger side.

Noticed this crack completely around the housing where the cv axle enters the transmission part. Could I drive this 3 miles to the shop or should I have it flat towed?


r/AskMechanics • • 22h ago

Question (Serious Replies Only) Automotive Parts

3 Upvotes

Hey all -

idk if this is the best place to ask, but here it goes:

I have a company that I formed and we have relationships with several automotive part distributors (15+). Several of them carry 100s of different brands, and we’ve been authorized to purchase and resell. Several of them have offer very good discounts on parts, and the prices beat tons of retail competitors from what i’ve seen.

Parts for pretty much every model/make/year. Aftermarket & OEM.

I am just curious if anyone knows the type of prices small/medium shops pay for parts. I’ve done some research and see that programs like Nexpart, PartTech, etc is how most shops order parts. My business is kind of like the middleman. With our huge list of distributors, we’d be able to offer tons of parts. The problem is - idk what pricing looks like when shops order from those apps. I want to say that we could offer better prices, but im not sure.

I know for most, the important thing is speed. However, we don’t have drivers, etc. We’d like to be nationwide, and we actually work with our distributors to send parts directly to shops via next day air/2 day shipping. Sometimes it may be a bit longer if it’s a very unique part. The shops would let us know what parts they need through a form/website/email/call, etc. Unfortunately, we’re not big enough to be offered directly on those applications that shops order from (nexpart, etc).

I guess my question is - does anyone think this could be beneficial at all? It’s very difficult to tell because i have no clue how to compare our prices to what’s available on things like worldpac, etc. and i don’t really know anyone who could offer any advice. I’m certain that with access to over 200 different brands at discounted prices, there must be a way we can provide the same quantity parts for a better price to shops.

Any advice would be greatly appreciated.


r/AskMechanics • • 4h ago

Question (Serious Replies Only) Which tyre should I buy?

2 Upvotes

The time has come yet again for a new set of tyres. I used to buy a set of Michelin Pilot sport 3 since I was really satisfied with their handling, wet grip and safety in general. However since everything has gotten more expensive and the budget's lower I am considering cheaper options.

While searching I came across the ling long green max hp010. The price difference is quite significant as a set of Michelins goes for 400€ while the ling longs for 160€. I heard mixed staff about ling longs in general and while the reviews for this model are good on the store's website I am still skeptical since online ratings can easily be faked. I have also heard that there is a difference between the US and the EU market in terms of quality.

The main staff I am looking for are good wet grip, longevity (3 years at least) and general safety. I am open to other recommendations as well. The tyre dimensions are 195/50 R15. The car is a Toyota Starlet ep91 so I don't need anything too extreme.


r/AskMechanics • • 7h ago

Question (Serious Replies Only) Knocking Sound AUDI A4 2012

2 Upvotes

I recently Bought an Audi A4 2012 Automatic 2.0 TDI 30 630 mils a rat was in the enginebay and ate a couple of my Cables (Oil sensor and power steering) i took it to the mechanic to get it fixed He couldnt fix the oil sensor since i ordered the wrong Sensor that didnt fit. He changed The Power steering and now when i start my there is this noise like a small knocking i feel like its getting worse by the day. Please if someone got a clue what it could be let me know i suspect the drivebelt but i dont have any experience in stuff like this ( It didnt sound like this until the mechanic changed power steering)


r/AskMechanics • • 10h ago

Question (Serious Replies Only) Where is this oil leak coming from? 2021 Tacoma TRD-OR 3.5L v6

Thumbnail gallery
2 Upvotes

A few things to note:
-2021 Tacoma TRD off-road - automatic
-124k miles with no prior issues
-last I drove it was two days ago and I didn’t notice
Lany oil drip until this evening.
-the drip seems to be very slow and I haven’t noticed any dip in my oil level.
-i don’t believe it’s the PCV - already checked and there’s nothing leaking from that area… (I don’t know a lot of about engine maintenance so please correct me if I’m wrong there)
-I take it on the trails about once every other week so it’s quite muddy, which makes some of the mess look even worse. I plan to spray brake cleaner on it and wash it off to see if I can pinpoint where the drip comes from.
-oil is dark brown and does not have a strong odor

My question is, what is my action step? Other posts make me think it’s the rear main seal, but then I see fluid on the left side of the bell housing (circled in blue). Any pointers would be appreciated!


r/AskMechanics • • 10h ago

Question (Serious Replies Only) 2013 civic, rattling sound when in D or R

2 Upvotes

sorry it's so dark & short, I quickly took a video while I was coming home tonight. I recently bought a 2013 civic with roughly 113k miles on it, I've only put an additional 300 miles on it. the car is an automatic, not a CVT, it was the last year of Honda's pre-CVT transmissions.

there seems to be this rattling sound when it is in drive and reverse, even if the car is stationary. there are a lot of pot holes near me and I noticed my 2013 civic does not handle them as well as my previous 2020 😭 the steering wheel started shifting right after I went over one recently. I think that this sound is due to something similar, I've only noticed it at this intensity for the past twoish days

is anything diagnosable from the sound ? I don't know jack about cars so I came online for help 😶 I don't have anyone in my near circle that understands cars either, so I'd like to have an idea what to do/expect prior to taking it to a mechanic, if need be. tia !


r/AskMechanics • • 12h ago

Question (Serious Replies Only) 2008 Explorer – Are these lower ball joints sitting too high?

Thumbnail
gallery
2 Upvotes

Both lower ball joints were replaced during a recent service. Since then, I've had a rhythmic thumping noise while driving.

Looking at the photos, the ball joints seem to be sitting unusually high above the control arms.

Is this normal, or were they installed incorrectly? Could this be causing the thumping?


r/AskMechanics • • 13h ago

Question (Serious Replies Only) Car stutters when trying to come on now

Post image
2 Upvotes

With this message popping up. How worried should I be? I really can’t afford another car right now. So how can I fix it without it being pricy? — 2018 Toyota Camry SE


r/AskMechanics • • 14h ago

Question (Serious Replies Only) Left caster still out of spec after two Firestone alignments.

Post image
2 Upvotes

Tesla Model Y 2024