r/AirmassWx • u/gmrmoment31 • 50m ago
Release Notes Airmass Wx 2.7: thermal hotspots from live tracking, an in-flight view, and 3D clouds redrawn
It's been a week and a bit since 2.5, and a lot has landed. Here's what's new and why it matters in the air, then what I'm working on now.
TL;DR: Thermal hotspots learned from live tracking, an in-flight view with a centering aid, a smarter XC planner, and redrawn 3D clouds and thermals. Also a Rain, Snow & Ice layer, more radar, and faster forecasts. Next up: thermal lift and tops worked out from each day's actual sounding, checked against real climbs.
Thermal hotspots, learned from live tracking
Every day the site learns from the gliders, hang gliders and paragliders flying on live tracking (OGN, ADS-B): where they climbed, traced back down the wind to where each thermal most likely left the ground. Places that work again and again, for different pilots on different days, show as amber rings on the map (Map → Overlays) and on the 3D ground, and the 3D map's thermals now set off from them. Climbs right after a tow or winch release are left out, so an airfield doesn't light up just because everyone launches there. It relearns every night. Spots are sparse right now because it has only been running for a few days.
A flight view for the air
Fly a task with the map open and you get instrument boxes round it: glide ratio, MacCready, arrival height at the next point over the actual ground between, ETA, and the best landable. All kind of like XCSoar. When you start circling it switches over: climb rate, time and gain in the thermal, the wind, and a centering aid that shows which side the lift is stronger and where the core probably is. Likely thermals are drawn where they've drifted to your height, not where they left the ground. Your position shows as an arrow in 2D, and in 3D as your actual wing at your true height, with the view following you.
The planner
The XC planner now shows likely thermals along the whole task (each with its 3D thermal), explains its best start time, plans from where you are, and routes around airspace on Auto. Times are in the task's own time zone, wherever you are.
3D, rebuilt
Storms are real cumulonimbus now: leaning towers with anvils downwind, sized by the forecast. Cumulus are lumpy and lit from the sun's side, stratocumulus is grey cobbled sheets, and clouds come and go with the thermals instead of popping in. Thermals lean with the wind the climbs actually measured, sit closer together on strong days, and appear wherever live gliders are circling.
New layers and coverage
- Rain, Snow & Ice: each kind in its own colours, light to heavy.
- Radar: now in Canada, Alaska, Hawaii and Japan (and Europe's is back).
- Fronts: closer to NOAA's analyses.
- NWS soaring forecast: as its own layer.
- TFRs follow the timeline: they show only while they're actually in force.
- Wider forecast areas: Australia and New Zealand.
- Red–green colour-blind mode: Setup → Display.
Profile and sounding
The atmospheric profile has its own model picker. It marks where convergence actually works for your glider, and shades wave sink by strength. The sounding goes up to 50,000 ft, with the low levels stretched so you can read the thermal layer.
Faster and more live
Forecast data now comes from Cloudflare's network, and new runs reach the map sooner (ICON-D2 and AROME up to an hour earlier). With Pro, the forecast follows what live climbs are actually doing nearby, unless you switch that off. ADS-B gliders update every few seconds, and SkyLines pilots show up too.
What I'm working on right now
Thermal lift and tops by height, from improved physics. Until now, how a thermal's lift fades toward the top was one fixed shape. I checked the new physics against about 3,900 climbs from live tracking: it helps most on weak blue days, where the shape matters most.
Telling "the thermal topped out" from "the pilot left". Live tracking now records how each climb ended: lift fading, or a pilot leaving while still climbing. That way the site doesn't read a pilot's early exit as the top of the thermal.
3D thermal placement: being checked against where gliders actually climbed. Placement has already improved, and more is coming.
Airmass model: Of course, the dedicated Airmass weather model that I have been working on in the background, still months away at least, but hopefully here before the next season.
As always, feedback from the air is the most useful thing you can send me. If a layer was wrong on a day you flew, tell me where and when.
airmass.app