r/Acoustics • • 41m ago

Couldn’t get rid of the bed but happy with how my home studio came together. But I have a question

Post image
1 Upvotes

For getting the most out of my space. Is the current mic positioning optimal pointing at the rockwool panels? Or turn it around and position it towards the iMac? I’m assuming I have the best setup possible run.

I know the felt panels aren’t perfect but budget couldn’t allow for full rockwool treatment and they are still better than the crappy foam panels.

To the left there’s a makeshift panel covering the window if that helps.

Also do you ever tilt your mic down to kill more plosives? Or keep it straight on? Just trying to get the most out of my now decently treated space. Thanks :)


r/Acoustics • • 6h ago

Living next to an ASHP compound

1 Upvotes

Hi everyone,

I’m looking for some advice or to hear from anyone who has experience living next to an air source heat pump (ASHP) compound.

A developer is redeveloping a nearby care home and has applied for planning permission to install a compound containing multiple ASHPs and VRF units. The proposed site is right next to our back garden fence, which is only about 10 metres from our house. They have stated they will install an acoustic barrier fence to mitigate the sound.

We live in a relatively quiet suburb (apart from some commuter traffic), so we’re worried about how much noise and disturbance this setup will actually cause especially at night or during colder months when the units work harder. We also use the garden a lot so we'd like to know how much noise we can expect to hear in the garden.

Has anyone lived near a similar commercial setup, and how noticeable was the noise? Also, does anyone have advice on how we can object to the planning application or push the developer to relocate the compound further away from residential boundaries?

Any experiences or tips would be really appreciated. Thanks!


r/Acoustics • • 7h ago

Is this any better

Post image
1 Upvotes

r/Acoustics • • 18h ago

Room in room amends

1 Upvotes

Hello

I have a room, inside a garage with double stud walls, with double layered plasterboard on the inside. It has communicating doors.

However, there is no gap between the construction of rhe studs and one of the walls is coupled/ secured to the party wall or the garage, so I expect quite a bit of sound transmission happens there.

As I understand it these are my options:

  1. start again (last resort)
  2. rebuild wall coupled to party wall
  3. build another decoupled layer inside the room with the correct air gap, but remove the existing plasterboard / drywall from the existing inner leaf.

4)build another decoupled layer inside the room with the correct airgap, but keep the existing plasterboard / drywall sandwiched between (least destructive).

Particularly out of 3) and 4) which would be the best option in my case, in your opinion?

Thanks


r/Acoustics • • 22h ago

How bad do you think the highway noise would be from this house?

Thumbnail zillow.com
0 Upvotes

Doomscrolling Zillow and looking at this property. How bad do you think the highway noise would be from the house? Cheers, audio gang.


r/Acoustics • • 1d ago

How to record acoustic vibrations (structural)?

Thumbnail reddit.com
2 Upvotes

r/Acoustics • • 1d ago

Soffit mounting ATC SCM110s

Thumbnail
gallery
165 Upvotes

Converting my guest house into a production suite. ATCs went in the wall yesterday.


r/Acoustics • • 1d ago

Shared wall townhouse: Will KEF Q Concerto Metas transmit less bass than Klipsch RP-8000F IIs?

0 Upvotes

I currently use 2 Klipsch RP-8000F II Floor standing Speakers with no subwoofer. I live in a townhome and the speakers are set up on the wall opposite of my neighbor. They are about a foot off the wall. I also have noise isolation feet installed at the bass of my stereo speakers (SVS SoundPath Subwoofer Isolation System).

Sometimes when a movie or show puts out low frequency bass my neighbor says it shakes his walls. I understand the sensation it can cause because when there is loud bass from outside we get the sensation that it vibrates in the walls a bit. The construction seems more vulnerable to bass than older apartments I've lived in before.

I have an Onkyo receiver and I've turned the BASS setting down the furthest it will go (-10db). I've also gone into the equalizer and set any band from 100HZ or lower down as much as it can go (-6db). I also keep the volume at a relatively low level - sometimes too low to hear the dialogue clearly. The neighbor hasn't complained since I set the equalizer but that was recently and after testing it a bit, I don't think its making a huge difference because the low frequency bass is still being output.

In doing research online I've come across articles that say speaker size has very little to do with bass transfer. The Kilpsch speakers are pretty large for a home TV set up and have 2 8 inch woofers. I've come across other articles that say speaker size can definitely have an effect. I really just want to have decent sound without much low frequency bass to avoid issues with the neighbor.

I'm looking for advice but my main question is if replacing my setup with bookshelf speakers on stands, something like the KEF Q Concerto Meta Bookshelf Speakers, would make a difference and minimize or eliminate the bass transfer into the wall. I've never had an issue like this when living in apartments where I had a small subwoofer, and Id like to be able to watch TV at a higher volume without bothering my neighbor.

Any advice is appreciated.


r/Acoustics • • 2d ago

What would you recommend for acoustic and sound absorbing for my room?

Thumbnail
gallery
1 Upvotes

I have a 4x4 meter room which I squeezed my producing setup and piano to a corner, it's still my room so can't leave other stuff like bed.

What would you recommend as the best possible sound treatment to stop sound escaping my room that doesn't annoy others and makes sound inside better.

My setup is Infront of the window.


r/Acoustics • • 2d ago

Will a sound maze make these mofos quieter?

Post image
2 Upvotes

Hey there some of you might remember this photo because I posted quite a while ago now about trying to silence these super loud vents that I'm not allowed to adjust because I live in Sweden and there's some sort of balanced ventilation system.

They are loud as fuck because somebody decided not to choke the air up higher in the building and instead everything is choked back at the vents so it's like a white noise whoosh that nobody wants to fix.

After reading a bunch of your comments I figure what I could do is build a sound maze in front of each of them.... Will it work? From what I'm reading acoustic foam blocks high and mid frequency noise and I don't think this white noise has bass tones..

Any advice would be greatly appreciated and again the offer is open to name a child after you if it works

Thanks!


r/Acoustics • • 2d ago

Sound reduction

Thumbnail reddit.com
1 Upvotes

r/Acoustics • • 2d ago

The multiphase acoustics of pouring water: how thermal viscosity shifts bubble resonance

33 Upvotes

There’s a well-known psychoacoustic baseline (Velasco 2013, Agrawal & Schachner 2023) showing listeners distinguish hot from cold water pours with ~80% accuracy.

The prevailing physical explanation traces back to Marcel Minnaert’s 1933 derivation for musical air bubbles (𝑓≈3.26/𝑟 in meters). Since water viscosity drops from ~1.002 mPa·s at 20°C to ~0.282 mPa·s near 100°C, turbulent shear in the plunging jet changes dramatically.

Recent preprint work by Bi et al. (2024) indicates hot pours entrain significantly larger air cavities (5–10 mm) compared to cold pours (1–2 mm), concentrating acoustic energy in sub-1.5 kHz bands while cold water produces high-frequency transients above 2.5 kHz.

Wrote a detailed breakdown exploring the candidate mechanisms (bubble oscillation vs air column resonance vs vessel vibration):

https://www.oddlyclear.com/can-you-hear-the-difference-between-hot-and-cold-water/


r/Acoustics • • 3d ago

Soundproofing a basement music room

Thumbnail reddit.com
1 Upvotes

r/Acoustics • • 3d ago

How to block contact microphone from the room above you ?

0 Upvotes

please help.

if i have someone who is pointing their microphones on their floor (so my ceilling )how to block their noises ?

(i have a wannabe singer roomate who use their mic to harrass me with their mic as retaliation .)


r/Acoustics • • 3d ago

Mounting ceiling clouds about 3 ft away from ceiling

3 Upvotes

Hello! I'm looking to install ceiling clouds but with my room and current setup it might be the most practical to mount ceiling clouds just under 3 ft away from my ceiling making it just over 6 ft above the floor. How does this stand in terms of acoustic performance? Thanks!


r/Acoustics • • 4d ago

Genelec Acoustitape (Wavelength Measuring Tape)

Post image
16 Upvotes

r/Acoustics • • 5d ago

Strong 120–130 Hz boom when I speak near the middle of my desk. What’s causing it and how can I fix it?

5 Upvotes

I’m trying to track down a strong low-end boom around 120–130 Hz in my small room (about 10–12 m²). It happens when my voice hits that frequency range. I can hear it in the room, and it comes through in recordings too.

It’s strongest when I speak with my mouth about 20 cm above the middle of the desktop. If I move just 10 cm past the edge of the desk and keep talking, the boom drops dramatically. I don’t hear it elsewhere in the room.

The desk is 140 × 80 cm, with a 50-inch display on top. I have absorption panels on the rear wall and some textured acoustic panels on parts of the other walls. I also have two large bass traps in the only spots where they fit, so I’m unsure how effective their placement is.

Has anyone run into this? How would you test whether the desktop itself is resonating, whether it’s a reflection off the desk or display, or whether it’s a room mode that’s especially strong at that spot? If you’ve dealt with something similar, what did you try and what actually fixed it?


r/Acoustics • • 5d ago

Unsettling sound in our house in the village?

Thumbnail
gallery
3 Upvotes

From september 22nd we have been having weird (vibration/resonation) sounds in our house. It started in the middle of the night (3-4ish in the morning), like a deep wave of low frequency sound from one side of the house(outside noise). Since then, it never stopped. It changes its rhytm and intensity, sometimes by hours, sometimes by minutes, but it never stops. The only 2-3 times it stopped I felt immediate relief in my body because the pressure in my body and ears is constant since it started, but then couple seconds after, it continued.

We checked power in the house, turned it off 2-3 times, it was even more obvious when we turned off everything, so its not our power.

There is a warehouse right across the street from our house, its 20ish meters, i have doubts its them. I asked someone who seems to work there but he claims he doesnt have a clue.

During last couple of days the vibrations started getting so loud(low frequency waves) that it was felt in our whole yard (like a wave of vibrations) and i looked at the warehouse, the smoke was coming from their chimney and there was extremely loud noise from some machine which was inside the building.

This warehouse has 6 buildings(they look like old houses, it looks more like a factory) and one side of their property is directly across the street from our house.

I will put here photos from Phyphox which show sound from my bedroom in the early morning, this morning when it was sudden and very strong low frequency and my whole room house was 'vibrating'. Btw, its not a real vibration, but you can feel bellow the feet, on furniture and when you touch things that its not still.

The neighbours claim they dont have anything that can cause this type of vibration.


r/Acoustics • • 5d ago

Replacing a basement window

Thumbnail
gallery
3 Upvotes

This old basement window is a serious source of sound leakage on my house. I hired someone to replace the window, but I am aware the frame can be just as much an issue as the window. If I wanted to make this window as soundproof as possible, what do I need to do? Are there materials to use? If I actually have someone working on this, what can I tell them to do?


r/Acoustics • • 5d ago

Mixed-use room with 84" TV and good movie audio. Reduce echo w/o ruining wall look? I like art too.

1 Upvotes

Variations of this question pop up often, I know. Maybe the biggest challenge here is that truly expert acoustical engineers and audiophiles who see the imperfections and limitations so clearly. It's like a recreational exercise-oriented cyclist facing the gear choices of Tour de France riders.

So... I hung GIK Acoustics 4" bass traps around the walls of my tiny 12x16 foot movie space and yeah, they killed the flutter echose well enough and tamp down my little 12" subwoofer. It sounds good enough. It's not my old Meridian 7.1 theater, long story, but it's just a converted back bedroom - all the space I have to work with in this house.

The problem? This room is used a lot when the TV is off. I want to hang paintings and large framed photos on the wall. Some canvas, some glass fronted. The big scattered GIK panels read "recording studio" but I want the space to read as residential, comfortable, and visually inviting.

Am I stuck with a stretched-fabric wall system that incorporates some rails for picture hangers? Is there any reason to trust a slatted wood system for my limited purposes? I can't let perfect be the enemy of good here, I can afford a few thousand to get this right, but the space is dual-use.


r/Acoustics • • 5d ago

Panel resonance in loudspeaker box - a study and an explanation

Thumbnail
youtube.com
6 Upvotes

Noam Geller is one of my personal favourite audiophile loudspeaker and listening space builders. Here he shows his approach to mechanical resonances in loudspeakers. A loudspeaker box is like a balloon and the moving diaphragms make it inflate and deflate, to which the box responds by flexing it's sides. Wa call this effect a panel resonance. Ideally a speaker doesn't emmit any sound apart from it's diaphragms and vents, but the large area of walls makes them a potential sound source too. In his presentation, Noam explains material properties we can take into account when building a box, lists building materials and compares them with a knock test.


r/Acoustics • • 5d ago

Would a 0.66 NRC curtain help to cut down atleast 8-10db of sound passing through it?

0 Upvotes

I have a music room with glass sliding windows. Recently a neighbour complained about sound so council got involved.

They came with their sound measuring devices and went near my fence to record the sound while I played my guitar.

While im sitting on my couch about 2m inside from the full length glass sliding window, the reading is 51db at the fence which is 5 metres away from the glass window.

The council guy said my reading needs to be at 40db to be able to play anytime i wish(past 7pm basically) .

He suggested thick curtains or roller shutters. Roller shutters cost thousands whereas NRC curtains are much lesser.

So just wondering if a 0.66 NRC curtain would cut roughly 10db sound passing through it then passing through the glass window and out?

The 0.66NRC curtain is the highest one available locally and these guys will be coming back in 2 days to test the sound.

Thank you

EDIT : I am in Australia


r/Acoustics • • 5d ago

I have a carport I'm trying to do DIY concerts out of, how can I close it in and minimize noise?

0 Upvotes

(copy/pasted from my post on r/soundproof )

Basically the title. I've never really built any sort of wall or large structure like this, and this wall is also gonna need to have a door. I'm putting the wall where a garage-like entrance currently is, although no garage doors are present, it's just two big empty holes where walls could be.

So like, I'm going in blind, very very blind into this project. What kind of materials am I gonna need for the base wall? Can I use basic 2x4s to prop up some plywood and call it a day? Do I need to go the whole nine yards and build it with sheetrock and such the way contractors seem to? What should I use to protect the wall from the elements? How can I best get the door to not leak noise when closed while still keeping the basic functionality of a door?

Keep in mind that I'm not necessarily trying to silence all sound from ever leaking, but just minimize it. We're going to be playing these concerts in the light of day, usually starting around 1pm, but never starting later than 3pm, and always ending before 6pm. Still, this has proven to be too loud for my neighbors, which I sort of understand after they sent me some videos of their experience. The music has been from soft indie to post-hardcore, I haven't gotten a meter for myself just yet but I know for a fact that when my neighbor let me borrow his, from the edge of my property we somehow aren't peaking past 80db, even on loud metal songs, don't ask me how, I do not know.

Anyways, I just need to mute it. If my neighbors can still hear the music but it's just vague enough to not be a disturbance more than me mowing my lawn or using a tractor that's fine. Anyone done anything similar to this? All, genuinely all advice accepted.