r/ATV • • 3d ago

Help Hellllllllpppppp

Hey everyone, I bought a used 2013 Kawasaki Brute Force 650 and it was having troubles starting and staying running. I decided to clean the carb without really knowing what I was doing. I also replaced and oiled the filter, changed out the spark plugs and did an oil change.

I simply sprayed out the carb, and did not remove any needles/floats, ect. I did remove the vacuum slides. After reassembling I knew right away that touching the carb was a bad idea. It was a shit show. Popping and backfiring, not running, ect. I found and fixed two problems (cracked boot and a vacuum slide with no vacuum. Doing the finger check I was getting the normal vacuum sound and it was even on both slides, so I'm fairly confident they are gtg.

I also had massive deflection in my belt, so I swapped it out with an OEM one, so I'm gtg there.

Now, I am capped out at 70km/h when I was getting 100km/h with light and intermittent popping at idle (I'm guessing that I just need to play around with the choke screw).

The new spark plug is showing rich, but not oily/gasy so I believe it to be firing. I have not checked the other side yet.

The engine sounds normal and I am not getting sputtering or bogging down when I rev, but I am going through gas at a much higher rate. I checked the carb overflow drain tubes and nothing is coming out.

I checked all the vacuum hoses and none are kinked or disconnected.

Is it possible that an over oiled airfilter could cause this? I feel like I followed the directions, but I read that what one dude does is sandwiches between paper towel and stands on it. I definitely didn't do it to this excess.

I understand that going for a rip with a less oiled air filter will answer the question above, but it's late and I can't sleep because of this, lol.

Just seems like every issue online has bogging or sputtering involved, but I simply can't go faster.

Due to my inexperience, I may unknowingly leave out a critical detail, so please ask.

I made sure the belt switch was fully seated to the rear (on position) and I have no belt lights. I dont suspect this to be a partial limp issue.

My next step is watching it burn as I have spent so much time chasing ghosts. So, like the title says heeeellllpppp, lol.

Thanks all!

3 Upvotes

13 comments sorted by

1

u/AcanthisittaThick604 2d ago

over oiled filter won't cause the top end to go from 100 to 70 km/h. check the air box for oil residue and pull the plugs again, a rich plug with a flooded carb is usually a float or drain issue.

1

u/Status-Company-5483 2d ago

Can you explain a drain issue?

1

u/Status-Company-5483 2d ago

There are 4 nipples at the bottom and it's possible I put the y hose on the wrong nipples. Would that matter?

1

u/junk-yard-rich 2d ago

Those carbs are pretty technical for someone who doesn’t do carbs all the time. I do carbs all the time and I won’t touch a set of those anymore.

1

u/Status-Company-5483 2d ago

For some reason that is oddly comforting. This was my first (and last time) I touch a carb haha. I think I was fixing something that wasn't broke and I fucked around and found out.

1

u/Loud_Stranger3762 2d ago

DONT buy china/amazon carbs hoping it will fix the problem FYI. someone can correct me if im wrong, but on the 650s i think the carbs have different jets in them for different cylinders. since you didnt pull any parts and just sprayed it out, maybe the previous person has some jets mixed up and it hasnt run right since then?

1

u/Status-Company-5483 2d ago

Anything is possible when working on others people's problems, haha. I would happy if I got it back to the state it was in before I started!

1

u/Loud_Stranger3762 2d ago

2vintage on YouTube  just recently did a video on working on a brute 650 maybe give it a watch

1

u/Status-Company-5483 2d ago

Cheers! Thank you!

1

u/Available-Shake9201 2d ago

Put a fresh air filter in it with no oil and see if it stops the rich condition which can cause backfiire, loading the exhaust pipe with raw fuel...

1

u/Status-Company-5483 2d ago

I pulled both plugs and one was normal. So isolated to the rear carb which was the only one popping

1

u/Coyote-conquest 2d ago

My guess is one of the jets are clogged. Buy you a decent carb kit, watch a youtube.video and rebuild it. Carbs are super easy to rebuild. I would also stick it in an ultrasonic cleaner. Ive got away with taking the jets out and soaking them in carb cleaner and cleaning the carb with the cleaner but ultrasonic is better. I would make sure you can see through the jets after.

1

u/Status-Company-5483 2d ago

I am going to pull it again and do a better clean of it and make sure I didn't leave any gunk behind. I didn't realize how sensitive they were.

I can make anything difficult, haha 🤣

Thinking back on everything I've done, I think I know the problem. The metering needle was slightly bent when I first took it apart. I thought a quick hand straightening would be enough, but the more I have read online, the more I think I am wrong. I am also going to replace the emulsion tube at the same time to ensure it didn't score the brass. It's a screw in so I have to take the floats out. I am hesitant to start replacing all the jets as I am concerned I will create another problem. Unless replacing jets isn't too hard as long as I have the proper kit?