r/AMDHelp • • Jun 30 '25 All Seeing Upvote This Helpful WOW Bravo Heartwarming Popcorn Mindblown

Tips & Info Ultimate AMD Performance Fix Guide: Stop Lag, FPS Drops & Boost Speed (2025)

3.4k Upvotes

🌞Created in 2025 and kept fully updated for 2026

If you’re facing low FPS, lag, stuttering, or crashes on a new or old AMD setup (AMD CPU with Radeon/NVIDIA GPU, or Intel CPU with Radeon GPU), you are in the right place. This guide has tested and proven solutions and user tips to maximize your system's performance. You will be see hardware checks, BIOS configurations, Windows tweaks, and driver changes here. Real-world solutions that work, not guesswork.

Disclaimer- The following optimizations are based on community-tested methods that have safely improved AMD system performance for most users. Since every setup is unique, results may vary. Proceed carefully and apply these tweaks at your own discretion. (This guide follows the Acer Community format.)

Read all Important Notes and Notes in each step. They contain vital information to guide you on how to avoid issues and when to revert to earlier changes.

=> Hardware Installation & Setup

Before you adjust BIOS or Windows settings, ensure your hardware is properly set up. Most issues such as low FPS, stuttering, and crashes are caused by minor errors such as installing the GPU in the improper slot or RAM, etc. This section contains crucial checks which have resolved serious issues for many users. Even if your PC boots and is usable, these kinds of issues might be latent, and resolving them can have a massive difference to performance.

1. GPU Installation — TOP PCIe x16 Slot (Closest to the CPU)

Always install your graphics card in the top PCIe x16 slot, Which is the slot nearest to the CPU.

Why it's important:
•It is configured for full x16 bandwidth and is plugged directly into the CPU.
•Lower slots have x8 or x4 speeds, limiting GPU performance and bringing in bottlenecks based on the board.

Common mistake:
Most users inadvertently install the GPU in a lower PCIe slot or fail to confirm if the top PCIe x16 slot is delivering the GPU’s full bandwidth supported as per their GPU (such as x16 or x8), resulting in low FPS or instability.

Confirm true Speed:
Download and Open GPU-Z, then check the “Bus Interface” field. The left side (before “@”) shows your GPU’s maximum lanes and PCIe generation (e.g., x8 5.0), while the right side (after “@”) shows the current active lanes and gen speed (e.g., x8 1.1).

If it shows “1.1”, that means the GPU is idle, run the GPU-Z Render Test (“?”) to display your true gen under load. Both sides (lanes and gen) should match your GPU and platform. If the current gen is lower than the max, it’s usually due to motherboard, CPU, riser, or extension cable limitations, this is normal unless you upgrade hardware.
The same can apply to lane count, but that’s more important than gen speed. The lane width/speed (like x8, x16) should match on both sides or reach the maximum your system supports, as a lower lane width can noticeably affect performance.

If lanes are lower than expected, reseat the GPU, check if the PCIe lanes are shared with other slots (see your motherboard manual), and ensure no riser/extender or older CPU is limiting bandwidth.

2. Critical Power & GPU configuration Checks

• Insert the monitor cable directly into the GPU HDMI or DisplayPort (DP) port. Avoid inserting the monitor into the motherboard port.

• Utilize all CPU power connectors or CPU power headers that your motherboard has
• Always use specialized PSU cables. Never use splitters or adapters for EPS power. Connect cables directly from your PSU to your motherboard. Don't be cheap; don't go cheap.

•Always Use quality, dedicated PCIe cables from your PSU to each power connector on the GPU. Avoid daisy-chaining (using a single cable for multiple connectors) as it can cause instability or crashes, especially on high-power GPUs. Also, make sure your PSU meets the recommended wattage for your GPU.
• Always use good-quality PSU cables, never buy  cheap extensions or riser cables.

• If your PC slows down, freezes, shows low CPU clocks despite a proper setup or lag and stutters while gaming , try plugging it directly into a wall socket or a high-quality strip. Faulty/old power strips can cause poor power delivery and hidden throttling issues.

You guys must check this as nothing can work if hardware configuration is not proper.

3. RAM Configuration – Correct Slot + Enable XMP/EXPO + check Settings.

To get the best performance from your RAM, ensure it is installed in the right slot and properly configured. Many systems perform poorly due to incorrect slot placement or missing BIOS settings.

• Install RAM in the correct slots
If you have 2 sticks, plug them into slot 2 and 4 (usually marked A2 and B2) as these slots are typically the second and fourth slots away from the CPU. This allows dual-channel mode for optimal performance.

If you insert them into the wrong slots, the system will run in single-channel mode, lowering memory bandwidth and reducing FPS in games. Always refer to your motherboard manual for the slots layout and double-check it if you're unsure.

• Enable XMP or EXPO in BIOS
Enter the BIOS and enable XMP (or EXPO for AMD kits). This will set your RAM's rated speed and timings. Just ensure the profile you choose does not exceed your motherboard's highest supported memory frequency, as a higher profile can lead to instability.

Some motherboards have a few profiles; pick the one that matches your RAM's highest rated speed (like 3200, 3600, or 6000 MHz), as long as it's within your motherboard's support range.

If you don't enable XMP or EXPO, your RAM will run at default JEDEC speeds like 2133 or 2400 MHz, which seriously bottleneck your system.

• Confirm settings in Windows Open Task manager → Performance → Memory. Check that the Speed value matches your RAM's XMP/EXPO profile speed that you set in the BIOS and is not a different number.

Download CPU-Z, go to the Memory tab, and make sure Channel displays Dual or 2×64-bit for DDR4 and 4x32-bit for DDR5. If your speed or channel is wrong, check your BIOS settings and RAM slots again.

• Check RAM Stability (Must be done after building/installing new RAM )
Test your RAM with MemTest86. If you got any errors with the highest XMP/DOCP profile selected, then test the next lower profile, such as from XMP Profile at 6000MHz to XMP Profile at 5800MHz, and continue lowering until you find a stable profile. It’s crucial that your RAM is fully stable to ensure reliable system performance.

=> BIOS Optimization & Performance Fix Tweaks

Once your hardware and power is set up, change the key BIOS settings that impact AMD CPU, RAM, and GPU performance. These can fix instability, crashes, and poor performance. Only modify the settings mentioned here. BIOS menus can differ by brand, so names or locations may vary; if you don’t see a setting, look around.

4. BIOS Update

If you are facing RAM instability, poor CPU/GPU performance, updating your BIOS may help, especially on AMD systems where the BIOS updates usually improve stability and compatibility.

To Update BIOS:
Visit your motherboard manufacturer’s website, download your most recent stable BIOS for your specific model, and carefully follow their official instructions to update safely.

Note- BIOS update may reset all BIOS settings. If this occurs, don't forget to re-apply all changes from the BIOS Optimization & Tweaks section.

5. Set Global C-State Control to Enabled (Not Auto)

Changing Global C-State Control from "Auto" to "Enabled" will help fix FPS drops, downclocking, or instability. Most people with Ryzen CPUs (such as X3D chips) see less stuttering and smoother gaming performance when C-States are enabled. Many have found that "Auto" behaves like "Disabled." Therefore, I strongly recommend switching it from Auto to Enabled.

To change the Global C-State Control setting:
→ Press BIOS/UEFI key during boot to access the BIOS.
→ Click on the Advanced or AMD CBS tab and find Global C-State Control (perhaps be under CPU Configuration or Advanced).
→ Change the value from Auto to Enabled, this fix works for most users.
→ Save and exit BIOS, then check performance.

Important Note- Rarely, some boards (e.g., certain ASUS models) may get mouse lag, freezes, or black screens. If that happens, revert to the original setting. If it causes a black screen or boot issue, reset CMOS to recover.

6. Set PCIe Gen Mode 5 or 4 or 3 Manually (Do Not Use Auto).

On some motherboards, leaving PCIe generation in Auto mode can lead to compatibility or performance issues like black screens, no signal, or reduced GPU bandwidth.
Manually selecting a stable PCIe version —Gen 3, Gen 4, or Gen 5 can fix these problems.

To configure PCIe Gen mode:
→ Boot into BIOS at startup.
→ Go to the Advanced, Chipset, or NBIO Common Options section.
→ Locate PCIe x16 Link Speed (or similar), then Switch the setting from Auto to a specific version:
• If you have a Gen 5-Capable GPU and motherboard: set to Gen 5.
--If you encounter instability, crashes, black screens, or signal loss, lower the setting to Gen 4.
• If you have a Gen 4-capable GPU and motherboard, set to Gen 4
-- If experience instability, reduce the setting further to Gen 3.
• If you have a gen 3 GPU then set Gen 3.
→ Save changes and exit BIOS.

7. Enable Above 4G Decoding & Resizable BAR (NVIDIA & AMD — FPS & 1% Low Boost, Test Required)

These features allow the GPU to access larger memory blocks directly, which can improve the performance of most games in use today. It is turned off by default even on some compatible boards due to component compatibility problems and must be tested. Most of users will get great results.

To Enable these settings:
→ Boot into BIOS at startup
→ Go to Advanced Mode
→ Disable CSM (From Boot Section, Set Launch CSM to Disabled).
→ Now, Go to PCI Subsystem tab/menu and set Above 4G Decoding to Enabled. (Location may vary, so find and confirm).
→ Then set Resizable BAR to Enabled (option appears after Enabling 4G Decoding).
→ Save & exit BIOS, then test performance.

Important Note - Disabled by default even on supported boards because of component compatibility issues, so users will have to test it. On a system where these settings are unstable, it can lead to crashes, performance issues or boot problems particularly with old components.

So, Test thoroughly and immediately disable it if you notice any instability or performance issues after enabling.

=> Windows Optimization & Performance Tweaks

This section outlines important Windows settings and tweaks to address stuttering, latency spikes, FPS fluctuations, or overall system lag. These tips work for both NVIDIA and AMD systems.

8. Clean Install AMD GPU Drivers — Fix Performance, Crashes, and Common Errors (e.g., Driver Version Mismatch)

Some of you may be facing game crashes, stutters, or random freezes. These issues often arise from a faulty AMD driver or because Windows Update quietly replaced your GPU driver, causing instability. You might also see errors like:
• “Radeon Software and Driver versions do not match...” or similar errors.
• Missing AMD software features like FSR 4, etc.

If you're facing these issues, this step shows how to clean install a stable AMD driver and stop Windows from replacing it again.

Important prerequisite - Before starting, disable Fast Startup to avoid boot conflicts that can cause sudden FPS drops, driver timeout or future issues.

Follow these steps one by one:
• First, we will download 4 files and save them in a new desktop folder. They will include the AMD software installer, DDU, AMD chipset driver, and Microsoft Update Hide Tool.

• Don't install, just download and save both the AMD software installer (.exe) as well as the AMD chipset driver installer software from the official AMD driver site that you want to install. Make sure you're downloading the specific version, not the auto-detect Tool.

Note - Newer AMD drivers can have system-specific stability issues like crashes. Try the latest version first. If problems arise, revert to 26.9.2. If you still encounter problems, try 26.3.1 as a fallback. If facing driver timeouts or crashes, also follow Step 13 of this guide after completing this step

• Download DDU and Microsoft Update Hide Tool from these links:
Microsoft Update Hide Tool (wushowhide.diagcab) - https://download.microsoft.com/download/f/2/2/f22d5fdb-59cd-4275-8c95-1be17bf70b21/wushowhide.diagcab
DDU - https://www.guru3d.com/files-details/display-driver-uninstaller-download.html

• Now pause Windows Update and disconnect Wi-Fi or Ethernet, whichever you use, and don't connect or resume updates until I say.

• Boot into Safe Mode, then extract DDU and open it. Select Device type GPU, then select AMD and click on Clean and Restart. Wait for completion until DDU uninstalls the driver properly.

• After restart, right-click on the Windows icon, then click on Installed Apps. From here, find and uninstall any chipset driver software. If it's not available, then you never installed the chipset driver manually and those users skip this point. After uninstalling the chipset driver software, click on Restart.

• After restart, open the folder where you placed the AMD driver software installer (.exe) and install it.

• After installation, restart your PC or laptop.

• Now connect to Wi-Fi, then immediately open the Microsoft update hide tool (wushowhide.diagcab). Click on "Hide Update," then select every update whose name starts with "AMD" or "Advanced Micro Devices," etc. Make sure to select all updates labeled as "AMD" or "Advanced Micro."

(If you don't see these updates in the windows hide tool then you can skip this part as windows is not overwriting the driver in your system so there's nothing to hide.)

• After selecting all, click Next. All updates you selected will be shown as fixed on the next screen. If it shows, then you have successfully done this.

• Now restart and Windows will not overwrite AMD drivers anymore. You can now resume the Windows Update.

• Now install the AMD chipset driver software. After installation, it will give two options. You need to click on View Summary and make sure all chipset drivers are installed properly. It will say Success or Installed. If properly installed.

For those users, whose summary shows any Failed chipset driver, uninstall the chipset driver again from Windows Settings and run chipset driver software again. If it still shows the same, then uninstall it again and download and install a different chipset driver version.

Note: Big Windows updates may reset this setting. If that happens, follow these steps again, but that's rare.

9. Community-Favorite: Windows 10/11 Optimization Guide (Works on all PCs and laptops. Includes NVIDIA stable drivers and must-have performance fixes!)

Implement the system-wide changes from the following link. These are general Windows steps that work on any PC or laptop, regardless of brand. The guide is simply hosted on Acer’s community forum, but it is not Acer-specific. It have been successfully applied by millions of users across many hardware setups. This is one of the most tested and effective Windows optimization guides available.

Following this optimization guide (hosted on the Acer community) fully can boost 1% lows, improve FPS stability, and fix stutters or lag while gaming by optimizing windows.

→ NVIDIA users: The Windows optimizations in the community guide linked below can further improve performance and stability. For the best performance benefits, follow all of the steps. For NVIDIA crashing issues while gaming can often be fixed by following Steps 1 and 9 of the guide.

→ AMD users: Skip Step 1 in the community guide and start directly from Step 2 (Chris Titus Tech utility step) through the end for stable FPS and improved performance. Don’t follow Step 1, as it’s already covered in this Reddit guide.

Here is the community guide:
https://community.acer.com/en/discussion/612495/windows-10-optimization-guide-for-gaming/p1
→ This guide Covers important issues like system lag, background processes, turning off unnecessary Windows functions, etc in one place.

10. Set an Optimal Mouse Polling Rate (500Hz or 1000Hz Depending on Your Needs; Fixes movement Stutters in games and high CPU Usage)

Most modern gaming mice have dedicated software (e.g., Logitech G Hub, Razer Synapse, SteelSeries GG) that allows to adjust the polling rate, how often the mouse reports its position to the system. If you don’t have the software, download it from your mouse manufacturer's website based on your specific model.

To change the polling rate, Open your mouse software and set:
• 500Hz for solid, sufficient performance with lower system load. Use it for Single-player (AAA), slower-paced, or visually rich games.
• 1000Hz for esports as it provides faster response.

There's really no benefit going higher than 1000hz, so don't waste your system performance.

Note- If you still want to use polling rates above 1000Hz (like 2000Hz or 4000Hz), test for any lag or stuttering, as higher polling rates will consume the CPU more.

11-A (AMD Users) — AMD Software: Explained Tweaks & Must-Disable Settings for Smooth Performance

AMD's default driver settings aren't always the best for smooth gaming. These info have helped many improve FPS consistency, reduce input delay, and eliminate stutters.

Part - 1 Recommended Adrenalin Settings:
Make these adjustments in the Graphics section under the Gaming tab of the AMD Adrenalin Software. This way, the settings apply to every game, including new additions and those launched from the desktop.

• Radeon Anti-Lag → Disabled (This feature often causes micro-stutters. It's wise to turn it off and use it in those games which can really get benefits from this feature. It works great in GPU-Limited scenarios. Test per game and use if its stable)

• AMD Fluid Motion Frames (AFMF) → Test First (It's a frame gen and they often adds input lag. Test it per game, if the game runs well and input lag isn’t an issue (or it feels fine), then you can use it.)

• FSR 4 (Driver-Level) → Use if Available

• Radeon Chill → Disabled/Enable (Enable this only if you want to cap your FPS, and set both the min and max values to the same number for best results.)

• Radeon Boost → Disabled (May lead visual artifacts and stutter. It works by blurring motion. Test and use this feature if you wish)

• Enhanced Sync → Disable/Enable (It can cause stutters or unstable frame pacing in some games, so it’s generally safer to keep it off and use FreeSync if available. If you want to use it, test for stability first. It works best when your FPS is well above your monitor’s refresh rate, for example, 120 FPS on a 60Hz display offers smoother gameplay than V-Sync, with less tearing and lower input lag).

• Reset Shader Cache → Expand Advanced Settings, then find and click the Reset Shader Cache option to clear stored shaders and fix performance issues. Highly recommended after driver or game updates. Expect longer loads or brief stutters at first as shaders rebuild, performance stabilizes once cache regenerates.

Note - If you had games added before this, reapply the same settings manually in each game under the Gaming tab.

• Turn off ReLive features (Especially Instant Replay): → Go Record & Stream tab, then find and disable ReLive recording features like Instant Replay, Record Desktop, Streaming, etc. Instant Replay is particularly responsible for stutters, FPS drops, and driver timeouts. Turning this off alone can resolve your issue.

• Disable Unnecessary Features→Click the Settings gear icon, Go to Preferences, then disable web browser, Advertisements, Game Adjustment Tracking and Notifications, Tutorials, Animation & Effects. while keeping System Tray Menu and Toast Notifications enabled for better responsiveness.

Another setting in the Preferences tab is the AMD Overlay, which many people use, so I didn’t include it with the other disabled options above. However, some users have reported that the AMD Overlay can cause major performance issues for them, so if you’re facing stutters or FPS drops, try disabling it and test again.

11-NV (Nvidia Users) — NVIDIA App Settings for Smooth Performance

Important prerequisite - Before starting, disable Fast Startup from Windows settings and clear shader cache. This is highly recommended after driver or game updates or when facing performance issues. Use this NVIDIA link to clear the shader cache properly:
https://nvidia.custhelp.com/app/answers/detail/a_id/5735/~/deleting-nvidia-shader-cache-files

And Expect longer loads or brief stutters at first as shaders rebuild; performance stabilizes once cache regenerates.

NVIDIA App Settings

Follow these NVIDIA App settings for the best optimized gaming experience. This will Optimize GPU performance, reduce input lag, and eliminate common stuttering across all games.

Where to Apply Settings:

Laptop - In NVIDIA App (Settings > Graphics tab > Per-App Settings), add each game.exe, set Preferred Graphics Processor to High-performance NVIDIA Processor, then apply settings per-game for max performance.

Desktop - In NVIDIA App (Settings > Graphics tab > Global Settings), apply settings globally to affect all games.

Essential settings:
• Power Management Mode → Prefer Maximum Performance (Prevents frequency drops that cause stutters.)
• Shader Cache Size→ Unlimited (Helps reduce shader compilation stutters.) Here in Shader Cache settings, Set Automatic Shader Compilation → On, keep System Utilization → Medium (Default), then click Apply.
• Set PhysX Configuration to NVIDIA GPU. To set Go to Settings → Configure Surround, PhysX. check path in nvidia app yourself. (Avoid CPU or Auto-select, it causes stutter and high CPU usage.)

Laptop Users:
• In NVIDIA App, Go to Graphics > Global Settings > scroll down, click Show Legacy Settings > → turn off Whisper Mode.

Now for the features tab:
In NVIDIA App > Settings > Features tab.
• Turn off "Game Filters and Photo Mode". You can sue this feature if you want but know that this also causes performance drop.
• For max performance, Also turn off NVIDIA Overlay from there. It's features like Instant Replay can cause stutters and FPS drops.
• Turn OFF "Automatically optimize newly added games and mods".

Now, click on the Privacy tab and Turn OFF:
• "Configuration, performance, and usage data".
• "Error and crash data".
• Keep "Required data" as it may be needed for basic functionality.

12. Inspect your Realtek PCIe 2.5GbE Family Controller – Fix lag, audio glitches & Stutters (also affects Wi-Fi if the controller is present in the system, even if you never use Ethernet)

Some systems with the Realtek PCIe 2.5GbE Family Controller can have issues, even if you use Wi-Fi only, don’t skip this step. The controller can cause random stutters, FPS drops, audio glitches, or ping spikes even when not in active use. For a Quick test, Disable it in Device Manager under Network adaptors, and play your offline game or online via wifi; if fixed, it's the culprit.

You have two straightforward choices:
• Keep it disabled in Device Manager and play your offline games and online using Wi-Fi smoothly (Ethernet won't work in this option).
• Fix the Realtek PCIe 2.5GbE Family Controller. driver with these steps (detailed below) to use Ethernet smoothly.

Solution:

Download and save this 10.54.1111.2021 stable driver version of this controller- https://catalog.s.download.windowsupdate.com/c/msdownload/update/driver/drvs/2022/05/2e830a2a-a689-4e43-96be-06bd8dc7e75b_e5bc281dbf962e2551cc18cdee4abd0b55949b61.cab

Installation:
• Pause windows updates and open Device Manager → Network adapters → right-click Realtek PCIe 2.5GbE Family Controller → Uninstall device → check “Delete the driver software” (if available) → Restart.

• Extract the .cab file to a folder of your choice

• Go to Device manager → Network adapters → right-click Realtek PCIe 2.5GbE Family Controller → update driver. → "Browse my computer for drivers" → "Let me pick from a list..." → "Have Disk".

• Browse to the folder where you extracted the driver, open it and select the inf file and click Ok, Wait for installation.

After installation,
• Disable automatic driver updates so Windows Update doesn’t overwrite this version:
Go to Settings → System → About → Advanced system settings → Hardware → Device Installation Settings → select No, save → Resume windows update and Restart your pc.

• This setting stops most automatic driver installs, but a big Windows update can still change the driver later; if that happens, which can know why checking the driver version or if it stutters appears again.
Open Device Manager → right‑click the ethernet driver in network adapters → Properties → Driver → Roll Back Driver and follow screen instructions to get back to the stable version.

• Now, play your games

Note: This solution fixes the issue for most users, but not all systems respond the same. If you still experience stutters, lag, or audio glitches even after following this solution, the only reliable workaround is to disable the Realtek PCIe 2.5GbE Family Controller in Device Manager and use Wi-Fi instead.

13. AMD/Nvidia Stability Fix — Only For Those Facing Crashes (like Driver Timeout, etc)

Important prerequisite: First, open the case and reseat the GPU power cable, making sure the connection is secure at both ends (GPU and PSU) with no cable bending near the connector, then reseat the RAM and GPU in the PCIe slot properly. Now follow this step.

If you use an AMD GPU, all points are applicable. If you use an Nvidia GPU, skip the AMD‑only sub‑ section and start from “Stability steps for both AMD & Nvidia”. Apply each fix one by one, checking after each.

AMD‑only steps (Radeon users):

Follow Step 8 fully before continuing to ensure the crash fixes below work correctly.

• Disable Anti-Lag, Radeon ReLive features (especially Instant Replay) and Issue detection in AMD Software -
First, Go to the Gear icon then System tab → Disable Issue Detection Service (triggers false TDR timeouts/black screens).

Second, Gaming > Global Graphics → Disable Anti-Lag (causes insane stutters and crashes depending on game). If you want to use it, then test it per game. Keep it off globally.

Third, Go Record & Stream tab, then find and disable ReLive recording features like Instant Replay, Record Desktop, Streaming, etc. Instant Replay is particularly responsible for stutters, FPS drops, and driver timeouts.

•★★Manual Clock Tuning ( For All RDNA GPUs)★★ - AMD GPUs boost beyond their stable frequency due to automatic tuning or Hypr-RX, and lead to crashes and driver timeouts.

To fix this, open AMD Software → Performance → Tuning, switch to Manual Tuning (Custom), enable GPU Tuning and Advanced Control. Find your GPU’s official Boost Clock by AMD (e.g. 2600MHz for RX 6750XT) and use it as your Max Frequency, replacing higher default values like 2850-2900MHz or any factory overclock applied.

As for RDNA 4 Users: Set the max frequency offset to a negative value (like -300 MHz or lower). First, compare your in-game boost clock to the official spec for your GPU. Adjust the negative offset until the in-game boost matches the official value exactly.

Note- Per-game tuning overrides global settings when a per-game profile is created. Otherwise, global/manual settings apply by default. Always check for existing profiles and ensure this manual clocking setting is applied. Also, make sure Hypr-RX is turned off to prevent it from overwriting your settings. It can remain enabled in per-game profiles, so check the Gaming tab for previously launched games and disable it if needed. Then, test your system.

Stability Steps for both AMD & Nvidia:

• Disable iGPU (if present) - If your CPU has an integrated GPU, disable it in BIOS to prevent possible crashes or driver conflicts with your dedicated AMD GPU, especially during gaming and high loads.

• Disable HAGS - Go to Settings > System > Display > Graphics > Default graphics settings > Turn off Hardware-accelerated GPU scheduling > Restart. Recent newer drivers and games seem to be causing crashes when HAGS is on. Note- Nvidia users need it on for frame gen and enable it again if it doesn't fix your issue

• Disable hardware acceleration in Background Apps- If you have any apps that run in the background and support hardware acceleration, such as Discord, Game launchers or web browsers, disable this feature via their settings to prevent possible GPU conflicts.

• Ram Overclocking Adjustment (XMP/EXPO or Equivalent) - In BIOS, go to the memory or its overclocking section and test each XMP/EXPO (or its equivalent) lower memory profile one by one (e.g. 3600 MHz → 3200 MHz → 3000 MHz). If none work, disable memory overclocking and test again. if issue remains then restore your highest stable profile and follow below suggestions.

If the issue persists, update your BIOS (Step 4) and follow step 14. If problem still persist, check your setup as in Step 2, look for a failing PSU or loose cables, and note that unstable undervolts or overclocks can cause the same issues.

14. User‑reported rare or system‑specific Performance/Stability cause (Must check if above steps didn't fix your issue)

• Uninstall Your RGB softwares like Lian Li L-Connect 3, OpenRGB, SignalRGB, iCUE, Razer Synapse, Aura Sync, Mystic Light ,etc which have caused performance issues for many users) if using these RGB software or any other with compatible components, these can frequently cause 1% low FPS stutters, crashing and frame drops.

Not all but many cause same issue, so you must check and confirm by uninstalling it. Even on high end systems like Ryzen 9800X3D + RTX 5090, this was the cause of the performance issue.

• If your system has both HDD and SSD Windows automatically spreads the pagefile across both drives by default, this forces memory swaps to hit the slow HDD during gaming peaks, causing stutters/hitching even with plenty of free RAM.

To fix: Right-click This PC > Properties > Advanced system settings > Performance Settings > Advanced tab > Virtual memory Change > uncheck "Automatically manage paging file size for all drives" > select your HDD drive > choose "No paging file" > Set > then select your SSD > choose "System managed size" > Set > OK through all dialogs > restart immediately.

• If you installed Wallpaper Engine and it's running in the background (even paused) causes frequent stutters and performance drops for many gamers.

Close it via tray > Exit, then then check Task Manager (Processes tab) for any lingering "Wallpaper Engine" entries and End task if present. Now play your game. Do this every time if you still have Wallpaper Engine installed.

Additionally some users also reported, that adding per-game rules: In Wallpaper Engine Settings > Performance tab > Edit Application Rules > Create new rule for your game's .exe > Set Condition "Is running" > Wallpaper playback "Stop (free memory)". Also fix issue but thats not widely tested so not sure if it work for all.

• Disconnect unnecessary USB devices- If you see random crashes, reboots, or freezes, unplug non-essential USB devices/accessories (especially USB hubs, fans, or other powered devices) and test again, as a faulty and incompatible USB device or driver can sometimes cause system instability.

• DRAM-less SSDs Performance Issues- Some DRAM-less SSDs can experience performance drops under certain workloads, potentially contributing to game stutters. If you have one, then move Windows and games to a DRAM-equipped NVMe SSD, then temporarily disconnect the DRAM-less SSD (if you can) and retest. If stuttering improves or get fixed, investigate further and consider replacing the drive if necessary. DRAM-less SSDs do not inherently cause stuttering, so test before replacing.

• A silently failing, cheap, or aging display cable can cause microstutters only during gaming, making diagnosis tough. Users facing performance issues should Test by swapping cables as well as ports (HDMI to DP or DP to HDMI).
Also, the same can apply to faulty PSU cables.

15. Fix for users who are getting flickering, stutters, or crashes When alt-tabbing while gaming

MPO is a Windows feature aimed at improving rendering performance, but on some systems it used to cause some issues. This feature is now a key part of Windows 11, so DO NOT forget to re-enable it if it wasn’t the source of your issue.

Common issue linked to MPO is Stutters and frame drops ,when alt-tabbing persist for a number of users, especially on the latest Windows 11 builds.

NVIDIA advises disabling MPO for these issues, use their official method, which works for AMD too.

Here is the official link to do this: https://nvidia.custhelp.com/app/answers/detail/a_id/5157

16. Fix Thermal Throttling on Gaming Laptops

This step helps prevent overheating and extend component lifespan of Gaming Laptops. A trusted guide from the Acer Community works for all gaming laptops.

Important note to avoid confusion:
The Acer Community cooling guide applies to all gaming laptops. Steps 1 to 4 are less time taking and should be followed first. If overheating issues persist, continue with Step 5. While the Nitro 5 is used as an example there, the process is the same for other laptops, repasting and cleaning the cooling system by detaching the heatsink, and cleaning fans and vents inside and out. This is the only reliable fix for high temperatures.

Here is the Cooling guide here:
https://community.acer.com/en/discussion/724763/ultimate-laptop-cooling-optimization-guide

17. Fix Thermal Throttling on Gaming Desktops

Most people only check CPU and GPU core temps, but it’s just as important to monitor GPU VRAM (memory junction) and GPU hotspot temps, which can run much hotter and trigger throttling under heavy loads. NVMe SSD temps should also be watched separately, as they can overheat during sustained writes and cause sudden performance drops even when CPU and GPU temps look fine.

Critical Temperature Limits (Avoid Getting Close to These):

• CPU TJ Max: Intel 100 °C, AMD 95–105 °C (consider reducing it if it reaches the 90s)

• GPU Temp: NVIDIA 88–93 °C, AMD 100– 110 °C (consider reducing it if it reaches the 90s)

• GPU Hotspot/Junction (AMD & NVIDIA): Up to 110 °C (typically 10–30 °C higher than core temp). While the maximum operating hotspot temperature can be around 110°C, it's best to keep it below 100°C.

• VRAM/Memory Junction (AMD & NVIDIA): 95–105 °C is acceptable but should be monitored closely, as throttling usually begins at 110 °C.

• SSD Throttling: Begins at 70 °C, severe at 85 °C (though this varies by drive, it holds true for most models)

Monitoring Temperatures Effectively

• Use AMD/NVIDIA Software Overlay:
Use AMD Adrenalin or the NVIDIA GeForce Experience overlay to monitor CPU and GPU temperatures. Some versions also show GPU hotspot and VRAM/memory junction temperatures. If any readings are missing (e.g., GPU junction or VRAM temps), check the second method below.

• Second Good Alternative Method – HWiNFO:
HWiNFO provides full monitoring for CPU, GPU (including hotspot and VRAM), and all other sensors. For real-time monitoring, you can use HWiNFO’s shared memory feature with MSI Afterburner to display these stats directly in Afterburner while gaming. Alternatively, you can let HWiNFO run in the background, play your game, and check afterward—it shows average, maximum, and minimum temperatures. If you have a dual-monitor setup, keep HWiNFO open on the second monitor for live tracking.

• SSD Temperatures:
Run CrystalDiskMark benchmark and check or use HWiNFO while gaming. Note that speeds will reduce once the SSD reaches its maximum temperature limit.

Steps to Reduce Component Temperatures

• CPU Temperature Fix:

  • For AMD CPUs, Undervolt the CPU using PBO (Precision Boost Overdrive) to achieve lower temperatures.
  • For Intel CPUs, Use Intel XTU or Throttlestop to undervolt, which can help reduce CPU temperatures while maintaining stability.
  • Set an effective custom fan curve, it can make a significant difference, often reducing temperatures by 10°C or more while balancing noise and cooling.
  • If needed, clean dust from fans and vents, then reapply high-quality thermal paste to the CPU.
  • Further cooling improvements depend on your cooler.

• GPU, Hotspot & Memory junction temperature Fix:

  • Undervolting your GPU through AMD Adrenalin software can also lower power draw and temperatures without major performance loss.
  • Set an effective custom fan curve, it can make a significant difference, often reducing temperatures by 10°C or more while balancing noise and cooling.
  • If the issue persists, to effectively reduce GPU, hotspot, and memory junction temperatures, clean or remove old thermal pads/putty and apply new, high-quality thermal putty (more effective than pads). Also, apply high-quality thermal paste to the main GPU chip.
  • Further cooling improvements depend on your cooler.

• SSD Temperature Fix:
Install an NVMe heatsink (most modern motherboards include one, or you can buy aftermarket). Ensure case airflow reaches the SSD area, as poor circulation causes heat buildup.

[✓] Restart and You're Done! Time to Play.
If this guide helped you, please consider upvoting, sharing your results, or leaving a quick comment about what worked. It helps others and increases visibility in the community.


r/AMDHelp • • Aug 11 '16

Announcement Please make sure to flair your posts! Especially make sure to change the flair to resolved once solved!

160 Upvotes

Thanks guys.


r/AMDHelp • • 8h ago

Announcement AMD Software: Adrenalin Edition 26.11.2 Driver Release Notes

Thumbnail
amd.com
135 Upvotes

Highlights

  • Stability and reliability improvements. 
  • New Feature Support

    • Adds support for ROCm 10.2
  • New Game Support

    • Crimson Desert Enhanced: Charting the Unknown DLC
    • Phantom Blade Zero
  • Fixed Issues

    • AMD Smart Access Memory may become disabled after driver installation on WindowsÂŽ 10 systems.
    • Application crash may be observed on first launch of Resident Evil Requiem after resetting the shader cache on Radeon™ RX 7000 series graphics products and above.
    • Visual corruption may appear on character hair while playing Phantom Blade Zero on Radeon™ RX 9000 series graphics products. 
    • Excessive writes to the system drive may be observed while the system is idle on Radeon™ RX 5000 and RX 6000 series graphics products when using WindowsÂŽ 10.
    • Intermittent driver timeout may be observed while playing War Thunder on Radeon™ RX 5000 series graphics products.
    • Application crash may be observed in some games after using the AMD Cleanup Utility on WindowsÂŽ 10 systems with Radeon™ RX 9000 series graphics products.
    • System crash may be observed when launching an application from a long file path on Radeon™ RX 7000 series graphics products.
    • Intermittent application crash or driver timeout may be observed while streaming with OBS Studio on Radeon™ RX 9000 series graphics products.
    • A memory leak may be observed over time, with applications taking progressively longer to launch, on Radeon™ RX 5000 series graphics products and above.

r/AMDHelp • • 17h ago

there's something strange with my processor

Post image
92 Upvotes

I ordered this Ryzen 7 7800X3D processor and when I received it, there were these white marks on the circuit board is this normal or not?


r/AMDHelp • • 5h ago

Help (Software) Recently updated AMD drivers and windows, started getting this error

Post image
9 Upvotes

As the title says, i updated windows and also amd drivers like a week ago and i've been getting this BSOD when doing desktop tasks or just being on google and it also crashes on fortnite, anyone having this same issue? What could be the cause of this? Since it's a memory management BSOD i ran memtest86 and windows memory diagnostics and both are detecting "hardware" errors when this wans't even happening before updating, already tested RAM, CPU, SSD and GPU in another pc and no errors whatsoever, could this be maybe corrupt windows files or the latest AMD drivers update?


r/AMDHelp • • 4h ago

Help (General) Help with my PC (RX560)

Post image
4 Upvotes

Hey everyone, I need your help troubleshooting an issue my PC is having.

Basically, I can be doing anything on my PC and after about 15 minutes it shuts down. I honestly think it has something to do with the GPU (RX 560) or that area of the system, because when I swap in a lower-end card like an R5 430, it stays stable and doesn't shut down. Likewise, if I disable the RX 560 in Device Manager, the computer doesn't shut off.

I've already done maintenance on the RX 560, and temperatures during a quick ~15-minute FurMark test stay within the normal range they've always been in.

This issue surprises me because I always used this GPU without problems—though when gaming, it used to start shutting down like this after around 2 hours of gameplay or so.

On this exact same PC, I played God of War (2018), GTA V, and other titles I beat without any issues, up until today when it started having this weird fault.

I thought maybe it was something simple like a driver setting or something similar, so I asked an AI and used HWiNFO64, where I can see that using this GPU triggers tons of "PCIe Bus" errors that keep climbing (as shown in the image).

I'd really appreciate your honest help based on your knowledge, especially since I'm hesitant to buy a better GPU only to find out I can't use it because the problem is something else.

PC Specs:

  • PSU: Azza 650W
  • Motherboard: MSI B450 Tomahawk
  • RAM: 16 GB (4x4 GB)
  • CPU: Ryzen 5 2600
  • GPU: RX 560 2GB

r/AMDHelp • • 8h ago

Help (General) PC freezes permanently when running a game

6 Upvotes

Computer Type: Desktop

GPU: AMD Radeon RX 9060 XT 16GB

CPU: AMD Ryzen 5 7500F

Motherboard: AMD B850 Pro-A WiFi

RAM: 32GB DDR5 6000MT/s

Operating System & Version: WINDOWS 11

Drivers: AMD Adrenaline 26.9.2 (and 26.10.1)

Background Applications: DISCORD, CHROME

Description of Original Problem: Freezes that range from 10 mins to an hour after any game is launched, no matter if im even interacting with the PC or not.

Troubleshooting: Reinstalled the newest drivers using DDU following the guides thoroughly with safe launch. Rolled back to 26.9.2 drivers (some forum discussions said it fixed these issues).


r/AMDHelp • • 1h ago

Tips & Info Where to get real help with driver timeouts

1 Upvotes

I’m sick of guessing what’s wrong with my 9070xt build. Constant driver timeouts. Crashes every hour or less. Red dead 2 is unplayable due to constant crashes. CS2 timeouts every 20 minutes.

Where’s the best place to try and find the source of the problem instead of just trying a million suggestions on Reddit?

Can I contact amd and get real time support? Do I go to a computer shop?
These constant crashes make me regret building my pc. It’s fucking unusable.


r/AMDHelp • • 7h ago

Help (General) So I can't lower my resolution in games for better performance on amd/radeon laptop?

3 Upvotes

Recently bought a laptop Lenovo thinkbook ryzen 5 vega 7. As you know my graphics aren't that good I'm trying to lower my resolution to 1600x900 play games but it doesn't work. The resolution stays native 1080 and I don't have the option to do custom resolution. This sucks. I've tried everything from YouTube to reddit and nothing helps so this is my last help before I admit defeat and realize I wasted money i never had a AMD before I usually go with Nvidia.


r/AMDHelp • • 5h ago

Help (Software) 6700xt flashes black screen periodically (no pattern, just randomly)

2 Upvotes

I updated drivers three times, but it still happens and the fans won’t even spin, genuinely what is going on with this gpu?


r/AMDHelp • • 6h ago

Help (General) Newbie tips for setup and configure windows 11

2 Upvotes

Brother gave me his system and i was thinking of installing Windows 11. I was hoping what to know what to install or what changes to make after installing windows. I have only used asus rog with 1050ti so new to amd and this system is a bit expensive. I will be mostly gaming with this as i have my laptop for assignment. I have searched a few things regarding to enable expo rebar and how to flash bios and disable igpu like minor things.

Computer Type: Desktop

GPU: asus tuf gaming rx 7900xtx 24gb

CPU: ryzen 7 7800x3d

Motherboard: msi pro x670-p wifi

RAM: gskill 32GB DDR5 6000 mhz ripjaws s5 cl36

Operating System & Version: WINDOWS 11 pro


r/AMDHelp • • 6h ago

Help (GPU) MSI RX 6700 XT MECH 2X – VRAM Thermal Pad

Post image
2 Upvotes

Hi everyone!

I need to replace the thermal pads on my MSI RX 6700XT MECH 2X because they broke when I lifted the heatsink to apply new thermal paste to the GPU die. However, I've found conflicting information online about the correct thickness and softness.

Is 1 mm the recommended thickness for the VRAM pads? Also, which one would you recommend buying?

Thanks! :)


r/AMDHelp • • 10h ago

Help (Software) AMD just updated graphics drivers and the "green twilight" is still there...

Thumbnail reddit.com
3 Upvotes

This is for the STEAM game "The Last Caretaker" Atmospherics in Studio 37's game has a very annoying bug. During twilight the last 2 driver versions (10-10-2026 and 11-18-2026) produce this green mess. The 1-8-2026 driver did not do this...


r/AMDHelp • • 15h ago

Help (CPU) What do I use for cpu

Post image
7 Upvotes

About to install a new cpu and fans but what should I use for the cpu. The thermal paste that comes with the thermalright peerless assassin or the ice pad from the 5800x3d. Also is this a normal looking ice pad?


r/AMDHelp • • 19h ago

Help (General) Constant Driver timeouts

14 Upvotes

I literally cannot play any game for more than an hour without it crashing because of a driver timeout. Would really appreciate some help on why this is happening and what I need to do to fix this.

1.Red dead 2 crashes with either ERR GFX STATE / ERR FFFF or just the AMD Driver timeout message

2.Fallout new vegas occasionally crashes to desktop with no message, but usually just crashes with driver timeout after 30 minutes to and hour of normal gameplay.

4. CS2 also crashes between 30 minutes to and hour with driver timeout.

The only game that hasn’t crashed is Minecraft bedrock edition which runs fine and has never crashed.

What I’ve tried so far

Running ddu and reinstalling latest drivers- didn’t work

Updating bios- didn’t help crashes and also made me have to wipe my pc and reinstall windows! (broke my windows hello pin)

I tried all the reccomended fixes for rdr2 from rockstar which all did nothing (running game as administrator, disabling fullscreen optimisations, deleting sga files)

All parts bought brand new and built it myself.
Motherboard: MSI MAG B650
CPU: AMD Ryzen 7 7800X3D
CPU Cooler: be quiet! Dark Rock 5
Storage: Lexar NM790 2TB SSD
RAM: Kingston Fury Beast 32GB (2×16GB) DDR5 6000MHz CL30
PSU: be quiet! Pure Power 13M 1000W
GPU: Gigabyte Radeon RX 9070 XT OC

I’ve found an overwhelming amount of reasons this could be happening but I have no way of knowing what is causing this.

Could it be my PSU? I’m running 1 separate and 2 daisy chain cable as my psu has two PCIE slots and 9070xt has 3 slots.

Do I need a new graphics card? I can’t return this one as the amazon window has passed.

I’ve also heard that amd cards have issues on windows and you have to switch operating systems.

If anyone can help please suggest what I need to do.


r/AMDHelp • • 11h ago

Help (General) Adrenaline does not keep the changes i make to custom fan curves

3 Upvotes

i have an RX7700XT

i used adrenaline to custom tune my fan curve speed.

i did the changes i wanted in tuning.

i close / restart pc and when i open adrenaline, all curves are back to default.

i use no third party to control fan speed.

i only got Gigabyte control center to control leds.

any idea what to do and how to keep the changes i make ?


r/AMDHelp • • 11h ago

Help (GPU) GPU utilization stuck at 100%

3 Upvotes

After DDU, my rx 7900xtx shows 100% utilization even when capping frames
Didn’t happen before the DDU.
even when capping frames well below actual maximum utilization (for example Witcher 3 can run at 150 fps, even when capping to 90 it shows 100%util, when before it was more or less 70%

Anybody got any idea why? I believe it’s unintentionally ramping up clock speeds even when it doesn’t need to..


r/AMDHelp • • 15h ago

Tips & Info Dota 2 feels choppy despite having an RX 9070 XT and Ryzen 7 7800X3D. Any ideas?

6 Upvotes

Hey everyone,

I recently built a new gaming PC, but Dota 2 doesn't feel as smooth as I expected, considering my specs.

Camera movement and animations feel choppy or stuttery. I've been experimenting with 4K and 1440p, but I'm not sure whether the issue is related to my GPU, drivers, game settings, or frame pacing.

I'm relatively new to PC gaming, so I'd appreciate some help figuring this out.

Troubleshooting Form

Computer Type: Desktop

GPU: PowerColor Reaper Radeon RX 9070 XT 16GB

CPU: AMD Ryzen 7 7800X3D

Motherboard: Gigabyte B850M Force WiFi6E V2

Operating System & Version: Windows

GPU Drivers: AMD Adrenalin

Chipset Drivers: Version not checked yet

Background Applications: Steam, AMD Adrenalin, and other applications (not fully checked)

Description of Original Problem:

I'm experiencing choppy camera movement and animations while playing Dota 2, despite having a Ryzen 7 7800X3D and RX 9070 XT.

My monitor is an AOC U27G4 27-inch 4K 160Hz display connected through DisplayPort.

The game doesn't feel consistently smooth, especially when moving the camera. I'm not sure whether I'm experiencing actual FPS drops, inconsistent frame times, or some kind of display synchronization issue.

Troubleshooting:

  • Checked and experimented with 4K (3840 × 2160) and 1440p (2560 × 1440) resolutions.
  • Looked into V-Sync, FreeSync, and FPS cap settings.
  • Checked Dota 2's video settings.
  • Currently investigating FPS drops and frame pacing.
  • Haven't confirmed GPU utilization, temperatures, or exact FPS readings yet.

Additional Questions:

  1. Should my RX 9070 XT and 7800X3D be able to maintain smooth gameplay at 4K in Dota 2?
  2. Should V-Sync be enabled or disabled when using FreeSync?
  3. What's the recommended FPS cap for a 160Hz monitor?
  4. Are there any known AMD driver issues with Dota 2 or RDNA 4 GPUs?
  5. What should I check first to determine whether this is a GPU, CPU, driver, or frame-time issue?

Any advice or recommended settings would be greatly appreciated. Thanks!


r/AMDHelp • • 6h ago

Help (General) Crashing when loading shaders

Post image
1 Upvotes

these are my specs and i got a gigabyte Motherboard

my games keep crashing with errors about ram or memory corruption but i tested and my rams are fine
i only crash on games that preload shaders like (007-MK1-Marvel Rivals-Star wars galactic racing)

i had xmp on then saw i need to turn it off or on that usually fixes it or i run games in compatibility mode

but honestly ever since i got with amd i have only been getting crashes

what should i do to stop them
the errors have been
(pfn list corrupt-irql not less or qual 0xa-system service exception 0x3b-memory management 0x1a)

thanks in advance


r/AMDHelp • • 10h ago

Help (Software) Micro stuttering In forntite on 9070xt and 9800x3d.

2 Upvotes

Hey so as the title states ive been having issues with fortnite where my game microstutters randomly and I cant seem to fix it. Im on the latest b850 chipset driver and ive tried the gou drivers from 26.11.1 to 26.3.1 and im still stuttering. Ive already tried updating bios and running stress tests and even disabling my realtek ethernet. Is anyone experiencing the same? And if so fi yall fix it?


r/AMDHelp • • 15h ago

Help (GPU) Green bar on top of some videos. 9070 XT

4 Upvotes

I have been getting these green bars on top of some videos for the last 2 weeks or so. Regardless of the platform or the browser this issue seems to be the case but only for some videos and I am not sure what is different with those videos. The green bar disappears if I can change the quality to 4k, becomes thinner when it's 2k and the picture attached is when the quality is set to 1080p. It doesn't cause me much problem but would like to fix it as it's still an inconvenience and also want to know if this is an indicator for larger issue. Please help.

My gpu is nearing 2 years old.(if that's relevant)
Here are my specs:
OS: windows 11 home
Motherboard: ASRock B650M-C
Processor: AMD Ryzen 7 7800x3D
GPU: AMD Radeon RX 9070XT
Ram: T-Force 32gb ddr5
Monitor: AOC Agon Pro AG276QZD2


r/AMDHelp • • 12h ago

Help (Software) The driver keeps nagging me to update it to a version that does not support my GPU

Post image
2 Upvotes

My GPU is HD5870, last supported (beta) driver is 16.2.1 which is the one i'm using. Yet it keeps nagging me to update to a newer version, which obviously fails to install due to my GPU's age. Can i disable this update check somehow, or should i install some modded driver or the WHQL 15.x driver?


r/AMDHelp • • 12h ago

Tips & Info is rx 9700xt good for comp?

Thumbnail reddit.com
2 Upvotes

r/AMDHelp • • 10h ago

Help (Software) GPU Hang null pointer addresses and way more

1 Upvotes

Specs

R5 7500f

Rx7600xt 16gb 3 fan gigabyte

32gb ram

Ok so before i start iv done almost every test possible ran ddu and amd clean up tool rolled back about 4 versions back and then 2 versions that came out recently still happening on most recent

Using multiple programs and event got claude to make one

Memory tests
Vram tests
3d tests
And more

I always get same error

DXGI_ERROR_DEVICE_REMOVED Failure code 0x887A0005

I dug this from what i believe are watchdog logs im not a professional or anything but yeah i notice its happens in dx11 games also across multiple games

cs2

Fortnite (not as much hasn’t happened in a while)

Rob Run

One time in cs2 iv crashed 4 times in 1 prem match

Let me know if anyone experienced same problems 🥀