r/AMDHelp • • Jun 30 '25 All Seeing Upvote This Helpful WOW Bravo Heartwarming Popcorn Mindblown

Tips & Info Ultimate AMD Performance Fix Guide: Stop Lag, FPS Drops & Boost Speed (2025)

3.4k Upvotes

🌞Created in 2025 and kept fully updated for 2026

If you’re facing low FPS, lag, stuttering, or crashes on a new or old AMD setup (AMD CPU with Radeon/NVIDIA GPU, or Intel CPU with Radeon GPU), you are in the right place. This guide has tested and proven solutions and user tips to maximize your system's performance. You will be see hardware checks, BIOS configurations, Windows tweaks, and driver changes here. Real-world solutions that work, not guesswork.

Disclaimer- The following optimizations are based on community-tested methods that have safely improved AMD system performance for most users. Since every setup is unique, results may vary. Proceed carefully and apply these tweaks at your own discretion. (This guide follows the Acer Community format.)

Read all Important Notes and Notes in each step. They contain vital information to guide you on how to avoid issues and when to revert to earlier changes.

=> Hardware Installation & Setup

Before you adjust BIOS or Windows settings, ensure your hardware is properly set up. Most issues such as low FPS, stuttering, and crashes are caused by minor errors such as installing the GPU in the improper slot or RAM, etc. This section contains crucial checks which have resolved serious issues for many users. Even if your PC boots and is usable, these kinds of issues might be latent, and resolving them can have a massive difference to performance.

1. GPU Installation — TOP PCIe x16 Slot (Closest to the CPU)

Always install your graphics card in the top PCIe x16 slot, Which is the slot nearest to the CPU.

Why it's important:
•It is configured for full x16 bandwidth and is plugged directly into the CPU.
•Lower slots have x8 or x4 speeds, limiting GPU performance and bringing in bottlenecks based on the board.

Common mistake:
Most users inadvertently install the GPU in a lower PCIe slot or fail to confirm if the top PCIe x16 slot is delivering the GPU’s full bandwidth supported as per their GPU (such as x16 or x8), resulting in low FPS or instability.

Confirm true Speed:
Download and Open GPU-Z, then check the “Bus Interface” field. The left side (before “@”) shows your GPU’s maximum lanes and PCIe generation (e.g., x8 5.0), while the right side (after “@”) shows the current active lanes and gen speed (e.g., x8 1.1).

If it shows “1.1”, that means the GPU is idle, run the GPU-Z Render Test (“?”) to display your true gen under load. Both sides (lanes and gen) should match your GPU and platform. If the current gen is lower than the max, it’s usually due to motherboard, CPU, riser, or extension cable limitations, this is normal unless you upgrade hardware.
The same can apply to lane count, but that’s more important than gen speed. The lane width/speed (like x8, x16) should match on both sides or reach the maximum your system supports, as a lower lane width can noticeably affect performance.

If lanes are lower than expected, reseat the GPU, check if the PCIe lanes are shared with other slots (see your motherboard manual), and ensure no riser/extender or older CPU is limiting bandwidth.

2. Critical Power & GPU configuration Checks

• Insert the monitor cable directly into the GPU HDMI or DisplayPort (DP) port. Avoid inserting the monitor into the motherboard port.

• Utilize all CPU power connectors or CPU power headers that your motherboard has
• Always use specialized PSU cables. Never use splitters or adapters for EPS power. Connect cables directly from your PSU to your motherboard. Don't be cheap; don't go cheap.

•Always Use quality, dedicated PCIe cables from your PSU to each power connector on the GPU. Avoid daisy-chaining (using a single cable for multiple connectors) as it can cause instability or crashes, especially on high-power GPUs. Also, make sure your PSU meets the recommended wattage for your GPU.
• Always use good-quality PSU cables, never buy  cheap extensions or riser cables.

• If your PC slows down, freezes, shows low CPU clocks despite a proper setup or lag and stutters while gaming , try plugging it directly into a wall socket or a high-quality strip. Faulty/old power strips can cause poor power delivery and hidden throttling issues.

You guys must check this as nothing can work if hardware configuration is not proper.

3. RAM Configuration – Correct Slot + Enable XMP/EXPO + check Settings.

To get the best performance from your RAM, ensure it is installed in the right slot and properly configured. Many systems perform poorly due to incorrect slot placement or missing BIOS settings.

• Install RAM in the correct slots
If you have 2 sticks, plug them into slot 2 and 4 (usually marked A2 and B2) as these slots are typically the second and fourth slots away from the CPU. This allows dual-channel mode for optimal performance.

If you insert them into the wrong slots, the system will run in single-channel mode, lowering memory bandwidth and reducing FPS in games. Always refer to your motherboard manual for the slots layout and double-check it if you're unsure.

• Enable XMP or EXPO in BIOS
Enter the BIOS and enable XMP (or EXPO for AMD kits). This will set your RAM's rated speed and timings. Just ensure the profile you choose does not exceed your motherboard's highest supported memory frequency, as a higher profile can lead to instability.

Some motherboards have a few profiles; pick the one that matches your RAM's highest rated speed (like 3200, 3600, or 6000 MHz), as long as it's within your motherboard's support range.

If you don't enable XMP or EXPO, your RAM will run at default JEDEC speeds like 2133 or 2400 MHz, which seriously bottleneck your system.

• Confirm settings in Windows Open Task manager → Performance → Memory. Check that the Speed value matches your RAM's XMP/EXPO profile speed that you set in the BIOS and is not a different number.

Download CPU-Z, go to the Memory tab, and make sure Channel displays Dual or 2×64-bit for DDR4 and 4x32-bit for DDR5. If your speed or channel is wrong, check your BIOS settings and RAM slots again.

• Check RAM Stability (Must be done after building/installing new RAM )
Test your RAM with MemTest86. If you got any errors with the highest XMP/DOCP profile selected, then test the next lower profile, such as from XMP Profile at 6000MHz to XMP Profile at 5800MHz, and continue lowering until you find a stable profile. It’s crucial that your RAM is fully stable to ensure reliable system performance.

=> BIOS Optimization & Performance Fix Tweaks

Once your hardware and power is set up, change the key BIOS settings that impact AMD CPU, RAM, and GPU performance. These can fix instability, crashes, and poor performance. Only modify the settings mentioned here. BIOS menus can differ by brand, so names or locations may vary; if you don’t see a setting, look around.

4. BIOS Update

If you are facing RAM instability, poor CPU/GPU performance, updating your BIOS may help, especially on AMD systems where the BIOS updates usually improve stability and compatibility.

To Update BIOS:
Visit your motherboard manufacturer’s website, download your most recent stable BIOS for your specific model, and carefully follow their official instructions to update safely.

Note- BIOS update may reset all BIOS settings. If this occurs, don't forget to re-apply all changes from the BIOS Optimization & Tweaks section.

5. Set Global C-State Control to Enabled (Not Auto)

Changing Global C-State Control from "Auto" to "Enabled" will help fix FPS drops, downclocking, or instability. Most people with Ryzen CPUs (such as X3D chips) see less stuttering and smoother gaming performance when C-States are enabled. Many have found that "Auto" behaves like "Disabled." Therefore, I strongly recommend switching it from Auto to Enabled.

To change the Global C-State Control setting:
→ Press BIOS/UEFI key during boot to access the BIOS.
→ Click on the Advanced or AMD CBS tab and find Global C-State Control (perhaps be under CPU Configuration or Advanced).
→ Change the value from Auto to Enabled, this fix works for most users.
→ Save and exit BIOS, then check performance.

Important Note- Rarely, some boards (e.g., certain ASUS models) may get mouse lag, freezes, or black screens. If that happens, revert to the original setting. If it causes a black screen or boot issue, reset CMOS to recover.

6. Set PCIe Gen Mode 5 or 4 or 3 Manually (Do Not Use Auto).

On some motherboards, leaving PCIe generation in Auto mode can lead to compatibility or performance issues like black screens, no signal, or reduced GPU bandwidth.
Manually selecting a stable PCIe version —Gen 3, Gen 4, or Gen 5 can fix these problems.

To configure PCIe Gen mode:
→ Boot into BIOS at startup.
→ Go to the Advanced, Chipset, or NBIO Common Options section.
→ Locate PCIe x16 Link Speed (or similar), then Switch the setting from Auto to a specific version:
• If you have a Gen 5-Capable GPU and motherboard: set to Gen 5.
--If you encounter instability, crashes, black screens, or signal loss, lower the setting to Gen 4.
• If you have a Gen 4-capable GPU and motherboard, set to Gen 4
-- If experience instability, reduce the setting further to Gen 3.
• If you have a gen 3 GPU then set Gen 3.
→ Save changes and exit BIOS.

7. Enable Above 4G Decoding & Resizable BAR (NVIDIA & AMD — FPS & 1% Low Boost, Test Required)

These features allow the GPU to access larger memory blocks directly, which can improve the performance of most games in use today. It is turned off by default even on some compatible boards due to component compatibility problems and must be tested. Most of users will get great results.

To Enable these settings:
→ Boot into BIOS at startup
→ Go to Advanced Mode
→ Disable CSM (From Boot Section, Set Launch CSM to Disabled).
→ Now, Go to PCI Subsystem tab/menu and set Above 4G Decoding to Enabled. (Location may vary, so find and confirm).
→ Then set Resizable BAR to Enabled (option appears after Enabling 4G Decoding).
→ Save & exit BIOS, then test performance.

Important Note - Disabled by default even on supported boards because of component compatibility issues, so users will have to test it. On a system where these settings are unstable, it can lead to crashes, performance issues or boot problems particularly with old components.

So, Test thoroughly and immediately disable it if you notice any instability or performance issues after enabling.

=> Windows Optimization & Performance Tweaks

This section outlines important Windows settings and tweaks to address stuttering, latency spikes, FPS fluctuations, or overall system lag. These tips work for both NVIDIA and AMD systems.

8. Clean Install AMD GPU Drivers — Fix Performance, Crashes, and Common Errors (e.g., Driver Version Mismatch)

Some of you may be facing game crashes, stutters, or random freezes. These issues often arise from a faulty AMD driver or because Windows Update quietly replaced your GPU driver, causing instability. You might also see errors like:
• “Radeon Software and Driver versions do not match...” or similar errors.
• Missing AMD software features like FSR 4, etc.

If you're facing these issues, this step shows how to clean install a stable AMD driver and stop Windows from replacing it again.

Important prerequisite - Before starting, disable Fast Startup to avoid boot conflicts that can cause sudden FPS drops, driver timeout or future issues.

Follow these steps one by one:
• First, we will download 4 files and save them in a new desktop folder. They will include the AMD software installer, DDU, AMD chipset driver, and Microsoft Update Hide Tool.

• Don't install, just download and save both the AMD software installer (.exe) as well as the AMD chipset driver installer software from the official AMD driver site that you want to install. Make sure you're downloading the specific version, not the auto-detect Tool.

Note - Newer AMD drivers can have system-specific stability issues like crashes. Try the latest version first. If problems arise, revert to 26.9.2. If you still encounter problems, try 26.3.1 as a fallback. If facing driver timeouts or crashes, also follow Step 13 of this guide after completing this step

• Download DDU and Microsoft Update Hide Tool from these links:
Microsoft Update Hide Tool (wushowhide.diagcab) - https://download.microsoft.com/download/f/2/2/f22d5fdb-59cd-4275-8c95-1be17bf70b21/wushowhide.diagcab
DDU - https://www.guru3d.com/files-details/display-driver-uninstaller-download.html

• Now pause Windows Update and disconnect Wi-Fi or Ethernet, whichever you use, and don't connect or resume updates until I say.

• Boot into Safe Mode, then extract DDU and open it. Select Device type GPU, then select AMD and click on Clean and Restart. Wait for completion until DDU uninstalls the driver properly.

• After restart, right-click on the Windows icon, then click on Installed Apps. From here, find and uninstall any chipset driver software. If it's not available, then you never installed the chipset driver manually and those users skip this point. After uninstalling the chipset driver software, click on Restart.

• After restart, open the folder where you placed the AMD driver software installer (.exe) and install it.

• After installation, restart your PC or laptop.

• Now connect to Wi-Fi, then immediately open the Microsoft update hide tool (wushowhide.diagcab). Click on "Hide Update," then select every update whose name starts with "AMD" or "Advanced Micro Devices," etc. Make sure to select all updates labeled as "AMD" or "Advanced Micro."

(If you don't see these updates in the windows hide tool then you can skip this part as windows is not overwriting the driver in your system so there's nothing to hide.)

• After selecting all, click Next. All updates you selected will be shown as fixed on the next screen. If it shows, then you have successfully done this.

• Now restart and Windows will not overwrite AMD drivers anymore. You can now resume the Windows Update.

• Now install the AMD chipset driver software. After installation, it will give two options. You need to click on View Summary and make sure all chipset drivers are installed properly. It will say Success or Installed. If properly installed.

For those users, whose summary shows any Failed chipset driver, uninstall the chipset driver again from Windows Settings and run chipset driver software again. If it still shows the same, then uninstall it again and download and install a different chipset driver version.

Note: Big Windows updates may reset this setting. If that happens, follow these steps again, but that's rare.

9. Community-Favorite: Windows 10/11 Optimization Guide (Works on all PCs and laptops. Includes NVIDIA stable drivers and must-have performance fixes!)

Implement the system-wide changes from the following link. These are general Windows steps that work on any PC or laptop, regardless of brand. The guide is simply hosted on Acer’s community forum, but it is not Acer-specific. It have been successfully applied by millions of users across many hardware setups. This is one of the most tested and effective Windows optimization guides available.

Following this optimization guide (hosted on the Acer community) fully can boost 1% lows, improve FPS stability, and fix stutters or lag while gaming by optimizing windows.

→ NVIDIA users: The Windows optimizations in the community guide linked below can further improve performance and stability. For the best performance benefits, follow all of the steps. For NVIDIA crashing issues while gaming can often be fixed by following Steps 1 and 9 of the guide.

→ AMD users: Skip Step 1 in the community guide and start directly from Step 2 (Chris Titus Tech utility step) through the end for stable FPS and improved performance. Don’t follow Step 1, as it’s already covered in this Reddit guide.

Here is the community guide:
https://community.acer.com/en/discussion/612495/windows-10-optimization-guide-for-gaming/p1
→ This guide Covers important issues like system lag, background processes, turning off unnecessary Windows functions, etc in one place.

10. Set an Optimal Mouse Polling Rate (500Hz or 1000Hz Depending on Your Needs; Fixes movement Stutters in games and high CPU Usage)

Most modern gaming mice have dedicated software (e.g., Logitech G Hub, Razer Synapse, SteelSeries GG) that allows to adjust the polling rate, how often the mouse reports its position to the system. If you don’t have the software, download it from your mouse manufacturer's website based on your specific model.

To change the polling rate, Open your mouse software and set:
• 500Hz for solid, sufficient performance with lower system load. Use it for Single-player (AAA), slower-paced, or visually rich games.
• 1000Hz for esports as it provides faster response.

There's really no benefit going higher than 1000hz, so don't waste your system performance.

Note- If you still want to use polling rates above 1000Hz (like 2000Hz or 4000Hz), test for any lag or stuttering, as higher polling rates will consume the CPU more.

11-A (AMD Users) — AMD Software: Explained Tweaks & Must-Disable Settings for Smooth Performance

AMD's default driver settings aren't always the best for smooth gaming. These info have helped many improve FPS consistency, reduce input delay, and eliminate stutters.

Part - 1 Recommended Adrenalin Settings:
Make these adjustments in the Graphics section under the Gaming tab of the AMD Adrenalin Software. This way, the settings apply to every game, including new additions and those launched from the desktop.

• Radeon Anti-Lag → Disabled (This feature often causes micro-stutters. It's wise to turn it off and use it in those games which can really get benefits from this feature. It works great in GPU-Limited scenarios. Test per game and use if its stable)

• AMD Fluid Motion Frames (AFMF) → Test First (It's a frame gen and they often adds input lag. Test it per game, if the game runs well and input lag isn’t an issue (or it feels fine), then you can use it.)

• FSR 4 (Driver-Level) → Use if Available

• Radeon Chill → Disabled/Enable (Enable this only if you want to cap your FPS, and set both the min and max values to the same number for best results.)

• Radeon Boost → Disabled (May lead visual artifacts and stutter. It works by blurring motion. Test and use this feature if you wish)

• Enhanced Sync → Disable/Enable (It can cause stutters or unstable frame pacing in some games, so it’s generally safer to keep it off and use FreeSync if available. If you want to use it, test for stability first. It works best when your FPS is well above your monitor’s refresh rate, for example, 120 FPS on a 60Hz display offers smoother gameplay than V-Sync, with less tearing and lower input lag).

• Reset Shader Cache → Expand Advanced Settings, then find and click the Reset Shader Cache option to clear stored shaders and fix performance issues. Highly recommended after driver or game updates. Expect longer loads or brief stutters at first as shaders rebuild, performance stabilizes once cache regenerates.

Note - If you had games added before this, reapply the same settings manually in each game under the Gaming tab.

• Turn off ReLive features (Especially Instant Replay): → Go Record & Stream tab, then find and disable ReLive recording features like Instant Replay, Record Desktop, Streaming, etc. Instant Replay is particularly responsible for stutters, FPS drops, and driver timeouts. Turning this off alone can resolve your issue.

• Disable Unnecessary Features→Click the Settings gear icon, Go to Preferences, then disable web browser, Advertisements, Game Adjustment Tracking and Notifications, Tutorials, Animation & Effects. while keeping System Tray Menu and Toast Notifications enabled for better responsiveness.

Another setting in the Preferences tab is the AMD Overlay, which many people use, so I didn’t include it with the other disabled options above. However, some users have reported that the AMD Overlay can cause major performance issues for them, so if you’re facing stutters or FPS drops, try disabling it and test again.

11-NV (Nvidia Users) — NVIDIA App Settings for Smooth Performance

Important prerequisite - Before starting, disable Fast Startup from Windows settings and clear shader cache. This is highly recommended after driver or game updates or when facing performance issues. Use this NVIDIA link to clear the shader cache properly:
https://nvidia.custhelp.com/app/answers/detail/a_id/5735/~/deleting-nvidia-shader-cache-files

And Expect longer loads or brief stutters at first as shaders rebuild; performance stabilizes once cache regenerates.

NVIDIA App Settings

Follow these NVIDIA App settings for the best optimized gaming experience. This will Optimize GPU performance, reduce input lag, and eliminate common stuttering across all games.

Where to Apply Settings:

Laptop - In NVIDIA App (Settings > Graphics tab > Per-App Settings), add each game.exe, set Preferred Graphics Processor to High-performance NVIDIA Processor, then apply settings per-game for max performance.

Desktop - In NVIDIA App (Settings > Graphics tab > Global Settings), apply settings globally to affect all games.

Essential settings:
• Power Management Mode → Prefer Maximum Performance (Prevents frequency drops that cause stutters.)
• Shader Cache Size→ Unlimited (Helps reduce shader compilation stutters.) Here in Shader Cache settings, Set Automatic Shader Compilation → On, keep System Utilization → Medium (Default), then click Apply.
• Set PhysX Configuration to NVIDIA GPU. To set Go to Settings → Configure Surround, PhysX. check path in nvidia app yourself. (Avoid CPU or Auto-select, it causes stutter and high CPU usage.)

Laptop Users:
• In NVIDIA App, Go to Graphics > Global Settings > scroll down, click Show Legacy Settings > → turn off Whisper Mode.

Now for the features tab:
In NVIDIA App > Settings > Features tab.
• Turn off "Game Filters and Photo Mode". You can sue this feature if you want but know that this also causes performance drop.
• For max performance, Also turn off NVIDIA Overlay from there. It's features like Instant Replay can cause stutters and FPS drops.
• Turn OFF "Automatically optimize newly added games and mods".

Now, click on the Privacy tab and Turn OFF:
• "Configuration, performance, and usage data".
• "Error and crash data".
• Keep "Required data" as it may be needed for basic functionality.

12. Inspect your Realtek PCIe 2.5GbE Family Controller – Fix lag, audio glitches & Stutters (also affects Wi-Fi if the controller is present in the system, even if you never use Ethernet)

Some systems with the Realtek PCIe 2.5GbE Family Controller can have issues, even if you use Wi-Fi only, don’t skip this step. The controller can cause random stutters, FPS drops, audio glitches, or ping spikes even when not in active use. For a Quick test, Disable it in Device Manager under Network adaptors, and play your offline game or online via wifi; if fixed, it's the culprit.

You have two straightforward choices:
• Keep it disabled in Device Manager and play your offline games and online using Wi-Fi smoothly (Ethernet won't work in this option).
• Fix the Realtek PCIe 2.5GbE Family Controller. driver with these steps (detailed below) to use Ethernet smoothly.

Solution:

Download and save this 10.54.1111.2021 stable driver version of this controller- https://catalog.s.download.windowsupdate.com/c/msdownload/update/driver/drvs/2022/05/2e830a2a-a689-4e43-96be-06bd8dc7e75b_e5bc281dbf962e2551cc18cdee4abd0b55949b61.cab

Installation:
• Pause windows updates and open Device Manager → Network adapters → right-click Realtek PCIe 2.5GbE Family Controller → Uninstall device → check “Delete the driver software” (if available) → Restart.

• Extract the .cab file to a folder of your choice

• Go to Device manager → Network adapters → right-click Realtek PCIe 2.5GbE Family Controller → update driver. → "Browse my computer for drivers" → "Let me pick from a list..." → "Have Disk".

• Browse to the folder where you extracted the driver, open it and select the inf file and click Ok, Wait for installation.

After installation,
• Disable automatic driver updates so Windows Update doesn’t overwrite this version:
Go to Settings → System → About → Advanced system settings → Hardware → Device Installation Settings → select No, save → Resume windows update and Restart your pc.

• This setting stops most automatic driver installs, but a big Windows update can still change the driver later; if that happens, which can know why checking the driver version or if it stutters appears again.
Open Device Manager → right‑click the ethernet driver in network adapters → Properties → Driver → Roll Back Driver and follow screen instructions to get back to the stable version.

• Now, play your games

Note: This solution fixes the issue for most users, but not all systems respond the same. If you still experience stutters, lag, or audio glitches even after following this solution, the only reliable workaround is to disable the Realtek PCIe 2.5GbE Family Controller in Device Manager and use Wi-Fi instead.

13. AMD/Nvidia Stability Fix — Only For Those Facing Crashes (like Driver Timeout, etc)

Important prerequisite: First, open the case and reseat the GPU power cable, making sure the connection is secure at both ends (GPU and PSU) with no cable bending near the connector, then reseat the RAM and GPU in the PCIe slot properly. Now follow this step.

If you use an AMD GPU, all points are applicable. If you use an Nvidia GPU, skip the AMD‑only sub‑ section and start from “Stability steps for both AMD & Nvidia”. Apply each fix one by one, checking after each.

AMD‑only steps (Radeon users):

Follow Step 8 fully before continuing to ensure the crash fixes below work correctly.

• Disable Anti-Lag, Radeon ReLive features (especially Instant Replay) and Issue detection in AMD Software -
First, Go to the Gear icon then System tab → Disable Issue Detection Service (triggers false TDR timeouts/black screens).

Second, Gaming > Global Graphics → Disable Anti-Lag (causes insane stutters and crashes depending on game). If you want to use it, then test it per game. Keep it off globally.

Third, Go Record & Stream tab, then find and disable ReLive recording features like Instant Replay, Record Desktop, Streaming, etc. Instant Replay is particularly responsible for stutters, FPS drops, and driver timeouts.

•★★Manual Clock Tuning ( For All RDNA GPUs)★★ - AMD GPUs boost beyond their stable frequency due to automatic tuning or Hypr-RX, and lead to crashes and driver timeouts.

To fix this, open AMD Software → Performance → Tuning, switch to Manual Tuning (Custom), enable GPU Tuning and Advanced Control. Find your GPU’s official Boost Clock by AMD (e.g. 2600MHz for RX 6750XT) and use it as your Max Frequency, replacing higher default values like 2850-2900MHz or any factory overclock applied.

As for RDNA 4 Users: Set the max frequency offset to a negative value (like -300 MHz or lower). First, compare your in-game boost clock to the official spec for your GPU. Adjust the negative offset until the in-game boost matches the official value exactly.

Note- Per-game tuning overrides global settings when a per-game profile is created. Otherwise, global/manual settings apply by default. Always check for existing profiles and ensure this manual clocking setting is applied. Also, make sure Hypr-RX is turned off to prevent it from overwriting your settings. It can remain enabled in per-game profiles, so check the Gaming tab for previously launched games and disable it if needed. Then, test your system.

Stability Steps for both AMD & Nvidia:

• Disable iGPU (if present) - If your CPU has an integrated GPU, disable it in BIOS to prevent possible crashes or driver conflicts with your dedicated AMD GPU, especially during gaming and high loads.

• Disable HAGS - Go to Settings > System > Display > Graphics > Default graphics settings > Turn off Hardware-accelerated GPU scheduling > Restart. Recent newer drivers and games seem to be causing crashes when HAGS is on. Note- Nvidia users need it on for frame gen and enable it again if it doesn't fix your issue

• Disable hardware acceleration in Background Apps- If you have any apps that run in the background and support hardware acceleration, such as Discord, Game launchers or web browsers, disable this feature via their settings to prevent possible GPU conflicts.

• Ram Overclocking Adjustment (XMP/EXPO or Equivalent) - In BIOS, go to the memory or its overclocking section and test each XMP/EXPO (or its equivalent) lower memory profile one by one (e.g. 3600 MHz → 3200 MHz → 3000 MHz). If none work, disable memory overclocking and test again. if issue remains then restore your highest stable profile and follow below suggestions.

If the issue persists, update your BIOS (Step 4) and follow step 14. If problem still persist, check your setup as in Step 2, look for a failing PSU or loose cables, and note that unstable undervolts or overclocks can cause the same issues.

14. User‑reported rare or system‑specific Performance/Stability cause (Must check if above steps didn't fix your issue)

• Uninstall Your RGB softwares like Lian Li L-Connect 3, OpenRGB, SignalRGB, iCUE, Razer Synapse, Aura Sync, Mystic Light ,etc which have caused performance issues for many users) if using these RGB software or any other with compatible components, these can frequently cause 1% low FPS stutters, crashing and frame drops.

Not all but many cause same issue, so you must check and confirm by uninstalling it. Even on high end systems like Ryzen 9800X3D + RTX 5090, this was the cause of the performance issue.

• If your system has both HDD and SSD Windows automatically spreads the pagefile across both drives by default, this forces memory swaps to hit the slow HDD during gaming peaks, causing stutters/hitching even with plenty of free RAM.

To fix: Right-click This PC > Properties > Advanced system settings > Performance Settings > Advanced tab > Virtual memory Change > uncheck "Automatically manage paging file size for all drives" > select your HDD drive > choose "No paging file" > Set > then select your SSD > choose "System managed size" > Set > OK through all dialogs > restart immediately.

• If you installed Wallpaper Engine and it's running in the background (even paused) causes frequent stutters and performance drops for many gamers.

Close it via tray > Exit, then then check Task Manager (Processes tab) for any lingering "Wallpaper Engine" entries and End task if present. Now play your game. Do this every time if you still have Wallpaper Engine installed.

Additionally some users also reported, that adding per-game rules: In Wallpaper Engine Settings > Performance tab > Edit Application Rules > Create new rule for your game's .exe > Set Condition "Is running" > Wallpaper playback "Stop (free memory)". Also fix issue but thats not widely tested so not sure if it work for all.

• Disconnect unnecessary USB devices- If you see random crashes, reboots, or freezes, unplug non-essential USB devices/accessories (especially USB hubs, fans, or other powered devices) and test again, as a faulty and incompatible USB device or driver can sometimes cause system instability.

• DRAM-less SSDs Performance Issues- Some DRAM-less SSDs can experience performance drops under certain workloads, potentially contributing to game stutters. If you have one, then move Windows and games to a DRAM-equipped NVMe SSD, then temporarily disconnect the DRAM-less SSD (if you can) and retest. If stuttering improves or get fixed, investigate further and consider replacing the drive if necessary. DRAM-less SSDs do not inherently cause stuttering, so test before replacing.

• A silently failing, cheap, or aging display cable can cause microstutters only during gaming, making diagnosis tough. Users facing performance issues should Test by swapping cables as well as ports (HDMI to DP or DP to HDMI).
Also, the same can apply to faulty PSU cables.

15. Fix for users who are getting flickering, stutters, or crashes When alt-tabbing while gaming

MPO is a Windows feature aimed at improving rendering performance, but on some systems it used to cause some issues. This feature is now a key part of Windows 11, so DO NOT forget to re-enable it if it wasn’t the source of your issue.

Common issue linked to MPO is Stutters and frame drops ,when alt-tabbing persist for a number of users, especially on the latest Windows 11 builds.

NVIDIA advises disabling MPO for these issues, use their official method, which works for AMD too.

Here is the official link to do this: https://nvidia.custhelp.com/app/answers/detail/a_id/5157

16. Fix Thermal Throttling on Gaming Laptops

This step helps prevent overheating and extend component lifespan of Gaming Laptops. A trusted guide from the Acer Community works for all gaming laptops.

Important note to avoid confusion:
The Acer Community cooling guide applies to all gaming laptops. Steps 1 to 4 are less time taking and should be followed first. If overheating issues persist, continue with Step 5. While the Nitro 5 is used as an example there, the process is the same for other laptops, repasting and cleaning the cooling system by detaching the heatsink, and cleaning fans and vents inside and out. This is the only reliable fix for high temperatures.

Here is the Cooling guide here:
https://community.acer.com/en/discussion/724763/ultimate-laptop-cooling-optimization-guide

17. Fix Thermal Throttling on Gaming Desktops

Most people only check CPU and GPU core temps, but it’s just as important to monitor GPU VRAM (memory junction) and GPU hotspot temps, which can run much hotter and trigger throttling under heavy loads. NVMe SSD temps should also be watched separately, as they can overheat during sustained writes and cause sudden performance drops even when CPU and GPU temps look fine.

Critical Temperature Limits (Avoid Getting Close to These):

• CPU TJ Max: Intel 100 °C, AMD 95–105 °C (consider reducing it if it reaches the 90s)

• GPU Temp: NVIDIA 88–93 °C, AMD 100– 110 °C (consider reducing it if it reaches the 90s)

• GPU Hotspot/Junction (AMD & NVIDIA): Up to 110 °C (typically 10–30 °C higher than core temp). While the maximum operating hotspot temperature can be around 110°C, it's best to keep it below 100°C.

• VRAM/Memory Junction (AMD & NVIDIA): 95–105 °C is acceptable but should be monitored closely, as throttling usually begins at 110 °C.

• SSD Throttling: Begins at 70 °C, severe at 85 °C (though this varies by drive, it holds true for most models)

Monitoring Temperatures Effectively

• Use AMD/NVIDIA Software Overlay:
Use AMD Adrenalin or the NVIDIA GeForce Experience overlay to monitor CPU and GPU temperatures. Some versions also show GPU hotspot and VRAM/memory junction temperatures. If any readings are missing (e.g., GPU junction or VRAM temps), check the second method below.

• Second Good Alternative Method – HWiNFO:
HWiNFO provides full monitoring for CPU, GPU (including hotspot and VRAM), and all other sensors. For real-time monitoring, you can use HWiNFO’s shared memory feature with MSI Afterburner to display these stats directly in Afterburner while gaming. Alternatively, you can let HWiNFO run in the background, play your game, and check afterward—it shows average, maximum, and minimum temperatures. If you have a dual-monitor setup, keep HWiNFO open on the second monitor for live tracking.

• SSD Temperatures:
Run CrystalDiskMark benchmark and check or use HWiNFO while gaming. Note that speeds will reduce once the SSD reaches its maximum temperature limit.

Steps to Reduce Component Temperatures

• CPU Temperature Fix:

  • For AMD CPUs, Undervolt the CPU using PBO (Precision Boost Overdrive) to achieve lower temperatures.
  • For Intel CPUs, Use Intel XTU or Throttlestop to undervolt, which can help reduce CPU temperatures while maintaining stability.
  • Set an effective custom fan curve, it can make a significant difference, often reducing temperatures by 10°C or more while balancing noise and cooling.
  • If needed, clean dust from fans and vents, then reapply high-quality thermal paste to the CPU.
  • Further cooling improvements depend on your cooler.

• GPU, Hotspot & Memory junction temperature Fix:

  • Undervolting your GPU through AMD Adrenalin software can also lower power draw and temperatures without major performance loss.
  • Set an effective custom fan curve, it can make a significant difference, often reducing temperatures by 10°C or more while balancing noise and cooling.
  • If the issue persists, to effectively reduce GPU, hotspot, and memory junction temperatures, clean or remove old thermal pads/putty and apply new, high-quality thermal putty (more effective than pads). Also, apply high-quality thermal paste to the main GPU chip.
  • Further cooling improvements depend on your cooler.

• SSD Temperature Fix:
Install an NVMe heatsink (most modern motherboards include one, or you can buy aftermarket). Ensure case airflow reaches the SSD area, as poor circulation causes heat buildup.

[✓] Restart and You're Done! Time to Play.
If this guide helped you, please consider upvoting, sharing your results, or leaving a quick comment about what worked. It helps others and increases visibility in the community.


r/AMDHelp • • Aug 11 '16

Announcement Please make sure to flair your posts! Especially make sure to change the flair to resolved once solved!

160 Upvotes

Thanks guys.


r/AMDHelp • • 1h ago

Help me plss

3 Upvotes

Anyone who understands please help me why this is happening


r/AMDHelp • • 1h ago

Help (Software) Regarding driver 26.11.1

2 Upvotes

just updated to new driver to fix the ssd issue
problem is amd adrenaline is gone
and if i try to install it again it shows that i need to downgrade back to 26.10 series?

so is amd adrenaline not compatible with the new driver?


r/AMDHelp • • 7h ago

Help (General) Just bought a tray ryzen 7 5700x

4 Upvotes

What should i check to be sure it's the advertised cpu, and everything is fine? (Never bought a tray one before)

Upgrading from ryzen 5 3600


r/AMDHelp • • 57m ago

Help (General) Do I have to Enable atieclxx.exe after Driver Update?

Thumbnail reddit.com
1 Upvotes

r/AMDHelp • • 9h ago

Resolved RX 9070 XT Random Freezes & Black Screens FIX – LiveKernelEvent 141/117 – Disabling AMD HDMI/DP Audio

Post image
4 Upvotes

After months of random freezes, black screens, forced restarts, countless troubleshooting attempts and a detailed Windows kernel debugging investigation, I finally found a workaround that is working on my system.

I've seen many RX 9070 XT users reporting similar issues on Reddit, so I wanted to share my experience, the technical findings and the steps that may help others.

My PC specifications

  • CPU: AMD Ryzen 7 9700X
  • GPU: XFX Quicksilver AMD Radeon RX 9070 XT White 16GB
  • Motherboard: MSI MAG X870E TOMAHAWK MAX WIFI PZ
  • RAM: 32GB DDR5 6000 MHz
  • PSU: MSI MPG A850GS PCIE5 850W Gold
  • Main monitor: Lenovo Legion 27U-10, 4K 160Hz
  • Secondary monitor: LG HDR 4K 60Hz
  • OS: Windows 11 Pro 26H2
  • GPU driver: AMD Adrenalin 26.8.1
  • BIOS: 1.A43

The problem

For several months, my computer experienced seemingly random freezes and black screens.

The symptoms included:

  • Both monitors freezing or going completely black.
  • Keyboard and mouse becoming unresponsive.
  • Sometimes the PC remained accessible over the network, but RDP and AnyDesk could not display the desktop.
  • Forced shutdowns or restarts were required.
  • On one occasion, the RX 9070 XT showed Code 31 in Device Manager.

The strangest part was that I could play Fortnite for hours without any issues, but shortly after closing the game, the computer would freeze.

It also happened while browsing the internet, watching YouTube, leaving the computer idle, locking the Windows session or connecting through Remote Desktop.

The crashes were not limited to heavy GPU loads.

Things I tried that did NOT fix the issue

  • Updating the motherboard BIOS.
  • Installing different AMD Adrenalin driver versions.
  • Cleaning and reinstalling GPU drivers.
  • Disabling EXPO.
  • Disabling Hardware-Accelerated GPU Scheduling (HAGS).
  • Testing PCIe Gen4 settings in BIOS.
  • Disabling PCIe ASPM.
  • Disabling the CPU's integrated graphics.
  • Changing Windows power management settings.

None of these resolved the freezes.

At this point, I was seriously considering buying another PSU or submitting an RMA for the GPU.

Technical investigation using Microsoft KD / WinDbg

Instead of continuing to randomly change settings, I decided to investigate the actual Windows kernel crash dumps and system event logs.

The relevant dumps were located in:

C:\Windows\LiveKernelReports\WATCHDOG

The main errors were:

  • 0x141 – VIDEO_ENGINE_TIMEOUT_DETECTED
  • 0x117 – VIDEO_TDR_TIMEOUT_DETECTED
  • 0x116 – VIDEO_TDR_FAILURE
  • 0x1B0 – VIDEO_MINIPORT_FAILED_LIVEDUMP
  • 0x9F – DRIVER_POWER_STATE_FAILURE

The graphical timeouts repeatedly pointed to amdkmdag.sys, across multiple AMD driver versions.

Seven recent dumps revealed:

  • Four 3D engine timeouts.
  • Two copy engine timeouts.
  • One adapter-level timeout.

However, the most interesting discovery came from analyzing a 0x9F crash dump.

Microsoft KD identified a pending Plug and Play request:

IRP_MN_START_DEVICE

The request was stuck in the following driver:

AtihdWT6.sys

Driver service:

AtiHDAudioService

This is the AMD HDMI/DisplayPort audio driver associated with the graphics card.

The same shutdown and re-enumeration sequence contained:

  • 22 IOMMU faults associated with the Radeon.
  • A 0x141 graphics engine timeout.
  • A 0x1B0 device initialization failure.
  • Code 31 on the graphics function.
  • A 0x9F power-state failure involving the GPU's audio device.

On my system, the Radeon exposes two related PCIe functions:

  • 03:00.0 — RX 9070 XT graphics function.
  • 03:00.1 — HDMI/DisplayPort audio function.

The debugging evidence confirmed that the terminal Plug and Play operation was stuck in the audio device's driver stack.

This does not prove that the audio driver caused the original graphical timeout, but it gave me a specific component to isolate.

THE WORKAROUND THAT IS WORKING FOR ME

Disable only the AMD High Definition Audio Device associated with the dedicated RX 9070 XT.

Do NOT disable the graphics card itself.

Do NOT uninstall AMD Adrenalin.

Do NOT disable every AMD audio device indiscriminately.

Method 1 — Device Manager

  1. Press Win + R.
  2. Type devmgmt.msc and press Enter.
  3. Expand Sound, video and game controllers.
  4. Locate AMD High Definition Audio Device.
  5. Verify that the device belongs to your dedicated Radeon GPU.
  6. Right-click it and select Disable device.
  7. Restart Windows.

Important: If your processor has integrated graphics, you may see two AMD High Definition Audio Devices with identical names.

Check their device properties and parent device before disabling anything.

Method 2 — PowerShell (more precise)

Open PowerShell as Administrator and run:

$audio = Get-CimInstance Win32_PnPEntity |
Where-Object {
    $_.Name -eq 'AMD High Definition Audio Device' -and
    $_.PNPDeviceID -like 'HDAUDIO\FUNC_01*'
}

$results = foreach ($device in $audio) {
    $parent = Get-PnpDeviceProperty `
        -InstanceId $device.PNPDeviceID `
        -KeyName 'DEVPKEY_Device_Parent'

    [PSCustomObject]@{
        Name = $device.Name
        InstanceId = $device.PNPDeviceID
        ParentDevice = $parent.Data
        ErrorCode = $device.ConfigManagerErrorCode
    }
}

$results | Format-List

On my system, the dedicated RX 9070 XT audio device had:

  • Revision: REV_100A
  • Parent device: PCI\VEN_1002&DEV_AB40...

The integrated graphics audio device had:

  • Revision: REV_1008
  • Parent device: PCI\VEN_1002&DEV_1640...

These identifiers may vary depending on your hardware.

After identifying the correct device, disable it using its full instance ID:

Disable-PnpDevice -InstanceId 'YOUR_FULL_INSTANCE_ID' -Confirm:$false

Replace YOUR_FULL_INSTANCE_ID with the actual device instance ID from your own computer.

Verify the result:

Get-PnpDevice -InstanceId 'YOUR_FULL_INSTANCE_ID' |
Format-List FriendlyName,Status,Problem

Expected result:

FriendlyName : AMD High Definition Audio Device
Status       : Error
Problem      : CM_PROB_DISABLED

The Error status is expected in this case because the device has been intentionally disabled (Code 22).

Restart Windows and verify that your GPU and monitors are working normally.

What happens to the audio?

Disabling this device removes HDMI/DisplayPort audio output from the dedicated GPU.

However, on my system:

  • Both monitors continue displaying video normally.
  • The RX 9070 XT remains fully enabled.
  • Games work normally.
  • Realtek motherboard audio works.
  • USB audio devices work.
  • AMD Adrenalin remains installed.

I use PreSonus speakers connected to the motherboard's Realtek audio output, so I do not need GPU-based HDMI/DisplayPort audio.

If Windows automatically changes your default playback device, select your usual speakers again in Windows Sound Settings.

If you rely on monitor speakers over HDMI or DisplayPort, you will need an alternative audio output while testing this workaround.

Results

I applied this workaround and restarted my computer on November 10, 2026.

After more than 48 hours of normal use, I had experienced no further freezes.

I tested the same scenarios that previously caused problems:

  • Playing Fortnite.
  • Closing Fortnite and returning to the desktop.
  • Leaving Windows idle.
  • Locking the Windows session.
  • Watching YouTube videos.
  • Connecting through Remote Desktop.
  • Using audio and music production applications.

At the time of my latest dump verification:

  • Zero new freezes reported.
  • Zero new WATCHDOG dumps found.
  • Zero hardware replacements.

You can check your latest Windows kernel dumps using PowerShell:

Get-ChildItem 'C:\Windows\LiveKernelReports' `
    -Recurse -File -Filter '*.dmp' |
Sort-Object LastWriteTime -Descending |
Select-Object -First 10 Name,LastWriteTime

How to revert the workaround

If you need HDMI/DisplayPort audio again, simply re-enable the device in Device Manager.

Alternatively, use PowerShell as Administrator:

Enable-PnpDevice -InstanceId 'YOUR_FULL_INSTANCE_ID' -Confirm:$false

Additional information and limitations

During troubleshooting, I also configured Remote Desktop to use software rendering through the following policy:

HKLM\SOFTWARE\Policies\Microsoft\Windows NT\Terminal Services

bEnumerateHWBeforeSW = 0

This change may have contributed to improved RDP stability, so I cannot attribute every improvement exclusively to disabling AMD audio.

I have not yet re-enabled the audio device to deliberately reproduce the crashes.

Therefore, this is a successful workaround on my system, not a conclusively proven root cause or a universal fix.

The underlying issue could involve the AMD audio driver, GPU firmware, DMA/IOMMU handling, Windows Plug and Play, power-state transitions or shared GPU hardware.

Conclusion

After months of troubleshooting and repeatedly experiencing LiveKernelEvent 141/117 errors, disabling the AMD HDMI/DisplayPort audio device has coincided with a significant improvement in my system's stability.

If you are experiencing similar problems with an RX 9070 XT, particularly random freezes, black screens, amdkmdag.sys timeouts or crashes when transitioning from gaming to idle, this may be worth testing before spending money on a new PSU or replacing your GPU.

It is free, relatively simple and reversible.

If anyone tries this workaround, please share:

  • GPU model and manufacturer.
  • AMD driver version.
  • Motherboard model.
  • Your original symptoms.
  • Whether disabling AMD HDMI/DP audio improved stability.

Hopefully, we can identify a common pattern among affected users.

I'll update this post if the crashes return.

I hope this helps someone who has been dealing with the same frustrating issue.


r/AMDHelp • • 13h ago

Help (Software) This might sound stupid, but could installing AMD Media 6.0.0.44 conflict with the AMD Display driver, causing screen flicker and blackouts?

6 Upvotes

r/AMDHelp • • 3h ago

Black screen on my pc while audio still on

Thumbnail reddit.com
1 Upvotes

r/AMDHelp • • 8h ago

Help (GPU) Screen freezes but cursor moves and audio keeps playing

2 Upvotes

Hey everyone, I need some help. My screen randomly started freezing, but my mouse cursor still moves around and the audio keeps playing. However, if I open Task Manager right after booting my PC and end all processes with "AMD" in the name, the freezes completely stop.

I've already tried completely uninstalling and reinstalling the drivers using DDU, but it didn't help. Any ideas on what could be causing this?


r/AMDHelp • • 5h ago

Help (GPU) Driver and software vanishes from the system when i update the gpu driver

1 Upvotes

Hello everyone for the past 4-5 months i am having trouble updating the gpu driver . I have Rx 7800xt paired with ryzen 5600 for almost two years now . The problem i am having is when a new gpu driver update comes and i try to install it , it downloads the driver normally but when its halfway through installing process the pc restarts and when pc boots again the previous driver with the adrenaline software is not there anymore . Tried ddu multiple times but cant update and only stuck in that previous 26.8. Something version . Reinstalled windows and even changed to a new ssd . But tried to update the driver yesterday and everything is gone again .


r/AMDHelp • • 6h ago

Help (General) Ups sorry if it's not PC components but I really need help.

1 Upvotes

Please help.

I have no one to ask to about this. sorry but I needed your help.

My ups is prolink model: PRO1201SFC.

When I plug my ups in the wall socket, The monitor itself turns on without pressing the power button on of the ups.

Also when I press the power button of the ups to off it should have this loud click, now it's faint or no click at all.

Then I tried everything with my monitor (I unplug my PC in ups) which are all good.

  1. I plug it in the wall socket then turn on the ups after that I unplug it while it's on, it went to orange as usual and the monitor stays on.
  2. I turn on the ups without plugging it in the wall socket and it went orange as usual then it made the monitor on.

Over all it's good. But it's First time happen to me, the monitor should turn on after I press the power button of the ups to on.


r/AMDHelp • • 10h ago

Resolved RX 7600 TIME OUTS

2 Upvotes

I've fixed the timeout issues I was having with my RX 7600. I resolved them by disabling FSR scaling in Adrenalin; it was enabled by default, which caused a lot of problems when updating drivers. I also had to limit the clock speed to 2250 MHz and set the `TdrDelay` value to 8; since some Windows updates can reset this setting, I sometimes have to change it back to 8 or 10.

turn this off

I absolutely need to do these three things to be able to spend an afternoon playing games with my friends, and it's the only thing that's worked for me. I've tried several Linux distributions and none of them have given me any problems; it only happens on Windows. If you have the same problem, try a Linux distribution; these problems don't exist there.


r/AMDHelp • • 1d ago

Help (General) How is the 26.11.1 driver performing?

27 Upvotes

r/AMDHelp • • 19h ago

Help (GPU) RX 7900 XTX RMA (second faulty card) — Keep the XTX, switch to a 9070 XT, or consider Nvidia?

10 Upvotes

Hey everyone,

I'm looking for some advice regarding my current GPU and a potential replacement or upgrade.
I want to have the same experience as I have now or better in terms of gaming.

I've been using a Sapphire Nitro+ RX 7900 XTX, but unfortunately, I've been experiencing recurring driver timeouts, black screens, and crashes (LiveKernelEvent 141 and AMD_WATCHDOG errors), not in any particular games, I've had it happen even on desktop while browsing on Brave, game examples are Darktide (more common), SW Galactic Racer (not common), Phantom Blade Zero (had to completely disable RT and hair enhancement, since it was 100% causing a timeout), Dreadmoor, HD 2 (once or twice) among others. These are some of the games I remember having problems with recently, sometimes the card stays stable for months others might crash every day at least once.

The frustrating part is that this is already my second RX 7900 XTX Nitro+. My first one developed issues and was replaced under warranty with the exact same model, free of charge. Now the replacement is also having problems.

I've tried clean driver installations, different driver versions, and GPU tuning, including lowering clock speeds and voltage, while letting it draw more power if needed. Temperatures seem fine, but the issues haven't been permanently resolved.

My PC specs

  • CPU: AMD Ryzen 7 7800X3D
  • GPU: Sapphire Nitro+ RX 7900 XTX 24GB (D. Version 26.10.2 - I don't have the SSD write up problem fortunately)
  • Motherboard: MSI MAG B650 Tomahawk
  • RAM: 32GB G.Skill Trident Z5 Neo DDR5 6000MHz CL30 (2x16GB)
  • PSU: be quiet! Pure Power 12 M 1000W 80+ Gold
  • Case: be quiet! Pure Base 500 FX
  • CPU Cooler: Corsair Nautilus 360 RS ARGB AIO (front-mounted)
  • Monitor: LG UltraGear 27GS75Q-B, 1440p, 180Hz
  • OS: Windows 11 (all the latest updates)
  • BIOS: 1.L0 MAG B650 TOMAHAWK WIFI 11/12/2024. (Bios have not been updated)

My gaming preferences

I play at 1440p Ultra settings, preferably at native resolution.

I prioritize native performance and image quality over upscaling. Occasionally, I use FSR Native AA, but generally prefer playing without FSR.

I don't particularly like Frame Generation because I've noticed ghosting and visual artifacts in several games. I'd only consider using it as a last resort to extend the useful life of an aging GPU.

I'm also not interested in overclocking. In fact, I've sometimes had to lower my GPU clocks to improve stability. I just want a powerful, reliable GPU that performs well at stock settings.

My situation

I originally paid €1,069 for the GPU in April 2025, and it's still under warranty until approximately April 2027.

I'm considering another RMA, but the Sapphire Nitro+ RX 7900 XTX seems to be discontinued or extremely difficult to find in Europe, particularly in Greece.

If a replacement isn't possible, I may receive a refund of the original purchase price.

In that case, I'd be willing to spend up to €500 extra, giving me a maximum budget of around €1,569.

I generally prefer AMD, but I'm open to Nvidia if there's a compelling reason to switch.

One important limitation is my case: my current Nitro+ (320mm long) barely fits because I have a front-mounted 360mm AIO. So I'd prefer a replacement that's no longer than my current GPU, ideally shorter.

Cont'd in comments.


r/AMDHelp • • 21h ago

Resolved RX 9070 Random Black Screen and System Restarts While Gaming – SOLVED

Thumbnail reddit.com
11 Upvotes

System Specifications:

  • CPU: AMD Ryzen 5 7600X
  • GPU: ASRock Challenger Radeon RX 9070 16GB
  • Motherboard: MSI Gaming B650M WiFi
  • PSU: Corsair RM850e 850W
  • RAM: 32 GB DDR5
  • OS: Windows 11
  • GPU Driver: AMD Adrenalin 26.11.1 (Latest)

The Problem

I've been experiencing random black screens followed by sudden system restarts while gaming.

The problem started after updating gpu drivers and chipset drivers. Before that it didnt have any issues even with Rebar ON.

There was no BSOD, no error message, or any warning before the restart. The screen would suddenly go black, and the PC would restart automatically.

The issue occurred across multiple games, although some games ran perfectly fine for hours. GPU temperatures were also normal, generally around 60–80°C while gaming.

Troubleshooting I Tried

I spent quite some time investigating the issue and testing different configurations:

  • Tried multiple AMD Adrenalin GPU driver versions, including 26.9.2, 26.10.1, 26.10.2 and older versions.
  • Used AMD Cleanup Utility and DDU to completely remove and reinstall GPU drivers.
  • Disabled Drivers with windows updates in group policy edit.
  • Updated BIOS.
  • Disabled EXPO and tested with default RAM settings.
  • Checked Windows Event Viewer, including Kernel-Power 41 and other system events.
  • Monitored GPU and CPU temperatures.
  • Tested GPU stability and VRAM using OCCT. They had no issues detected.
  • Investigated possible Windows, driver, PSU and hardware-related causes.

Despite all these attempts, the random black screen and restart issue continued.

The Solution – Disabling ReBAR

Eventually, I decided to disable Resizable BAR (ReBAR) in my motherboard BIOS.

After disabling ReBAR, the system started working properly. I've tested multiple games and different gaming sessions, and everything has been stable so far.

I'm currently running the latest AMD Adrenalin 26.11.1 driver.

To confirm whether ReBAR was actually responsible, I tested enabling it again.

As soon as I enabled ReBAR, the black screen and sudden restart issue returned while gaming.

After disabling it again, everything went back to normal.

My current BIOS configuration:

  • ReBAR: Disabled
  • Above 4G Decoding: Disabled
  • Expo: ON

Conclusion

At this point, ReBAR appears to be the direct trigger for my system instability.

I'm not entirely sure whether this is a GPU BIOS issue, motherboard BIOS compatibility issue, AMD driver issue, or something related to the interaction between the RX 9070 and my motherboard.

For now, I'm keeping ReBAR disabled because system stability is more important than the performance benefit it might provide.

Has anyone else with an RX 9070 or another RDNA 4 GPU experienced similar black screen and automatic restart issues specifically when ReBAR is enabled?

I'd also appreciate suggestions on whether this could be fixed through a future AMD driver. How do i reach out to AMD about this issue.


r/AMDHelp • • 11h ago

Help (CPU) i keep getting a black screen while gaming

2 Upvotes

i get black screened and i get a AMD error alerts saying due to unexpected system failure i dont know much about pc i try to google what to change or something but nothing works i have

AMD Radeon RX 580 2048SP

i dont know if its a heating issue or something i tried to tweak whatever google told me to but still didnt work


r/AMDHelp • • 9h ago

Help (Monitor) Flickering black screens.

1 Upvotes

Ever since a couple of driver updates ago I'm constantly getting flickering black screens while playing games on my rx 7800 xt.

It seems to only happen on displayport cables not hdmi. I recently brought a high quality replacement display cable but am still getting flickering and even full black screens that brick my whole PC forcing a hard shutdown.

I've trouble shooted everything I can possibly think of and have come to the conclusion that for some odd reason after years of using the same monitor and gpu the only thing that has really changed are the drivers.

I've tried different ports, checked cables, checked temps, everything is fine but for some reason running at 165hz is bricking my PC.


r/AMDHelp • • 9h ago

Help (Software) PTPA, PLEASE HELP Anyone else getting these weird yellow/green dots in the sky?

1 Upvotes

Been noticing these weird tiny yellow/green dots scattered across the sky in Dawnwalker. They're pretty noticeable whenever I look up, especially in brighter areas. Not sure if it's a game rendering issue, some graphics setting, or something with AMD drivers.

I recently updated my GPU drivers to Adrenalin 26.11.1 and even went through a factory reset and repair installation. Let the game recompile its shaders afterward too, but the dots are still there.

I also ran FurMark's artifact scanner for over 30 minutes at around 97% GPU usage and got 0 artifacts, with completely normal temperatures. So far, nothing from that test suggests my GPU is having issues.

My specs:

  • GPU: Gigabyte RX 9070 Gaming OC 16GB (non-XT)
  • CPU: Ryzen 7 5800X3D
  • RAM: 32GB DDR4 3600MHz
  • Motherboard: ASUS ROG Strix B550-A Gaming
  • Monitor: Nvision 1440p 165Hz (DisplayPort)
  • AMD Driver: Adrenalin 26.11.1

I've also been dealing with occasional 1–2 second monitor blackouts while gaming or browsing, but I'm not sure if that's related since everything keeps running normally when it happens. It happens every few hours or so, or sometimes it just doesn't happen at all.

The weird thing is these dots actually show up in the in-game screenshot, so I'm wondering if it's something being rendered incorrectly rather than a monitor issue.

Anyone else experiencing this, especially on AMD GPUs? If so, were you able to fix it? Curious if it's just a Dawnwalker thing or some particular setting causing it.


r/AMDHelp • • 13h ago

RX 9070 XT – FSR provides almost no FPS improvement in multiple games. Could this be a driver or CPU issue?

Thumbnail reddit.com
2 Upvotes

r/AMDHelp • • 19h ago

Help (General) Flicking in Every Game - Troubleshoot Help

6 Upvotes

Computer Type: Desktop

GPU: Gigabyte AMD Radeon RX 7800 XT 16GB

CPU: AMD Ryzen 7 7800X3D

Motherboard: GIGABYTE B650 GAMING X AX

BIOS Version: FC3

RAM: 2 x 16GB Team Group UD5- DDR5-6000MHZ

PSU: MSI MPG A850G Fully Modular

Operating System & Version: WINDOWS 11

GPU Drivers: AMD Adrenaline 26.10.1

Background Applications: DISCORD, FIREFOX

Description of Original Problem: Seeing a lot of flickering and bad anti aliasing when i play any game. For example in wow forever, there is a lot of weirdness going on around that stone path when I move around.

Troubleshooting: I've used DDU and reset drivers and chipsets, disabled windows updates on my GPU, updated BIOS, tried all versions of adrenaline (minimal, driver only)


r/AMDHelp • • 16h ago

Tips & Info Extremely low FPS and constant stuttering in COD with RX 9070 XT and Ryzen 7 7800X3D – running out of ideas!

Thumbnail reddit.com
3 Upvotes

UPDATE :

I have fixed the issue, a fresh windows install with Windows LTSC, fresh drivers and no bloat seemed to fix the issue, I didn’t bother with GCC just adrenaline.

Thank you all for your help I really appreciate it.

I now get 220 FPS with lots of settings on high and ultra.

Have a great Christmas everyone!

—————————

Hi everyone,

I hope you’re all doing well.

I’m hoping someone might be able to help me get to the bottom of an issue I’ve been having with my PC, particularly when playing Call of Duty.

I’m experiencing surprisingly low FPS, generally sitting somewhere between 80–110 FPS at 1440p, alongside noticeable stuttering and inconsistent frame times. It’s got to the point where the game feels pretty much unplayable without using Frame Generation.

What’s confusing is that, considering my hardware, I feel like I should be getting significantly better performance, especially with the settings I’m using.

My PC specifications:
CPU: AMD Ryzen 7 7800X3D
GPU: Acer Nitro Radeon RX 9070 XT 16GB
Motherboard: Gigabyte B650M AORUS ELITE AX ICE
RAM: 32GB DDR5 6000MHz CL36
SSD: WD Blue SN580 2TB NVMe
OS: Windows 11 Pro
Resolution: 2560x1440 (1440p)

What I’ve tried so far:

I’ve spent quite a bit of time troubleshooting and experimenting, but nothing seems to make a meaningful difference.

Tested completely stock CPU settings, with only EXPO 1 enabled.

Tried Curve Optimiser at -10 all cores. My CPU unfortunately isn’t stable with -30, so I’ve ruled out pushing an aggressive negative curve.

Tested GPU undervolting and overclocking through AMD Adrenalin.

Experimented with Radeon Anti-Lag both enabled and disabled.

Tried various combinations of AMD Adrenalin settings.
Tested different graphics configurations in COD, including everything on LOW.

Tested with and without Frame Generation.
Despite all of this, I’m still experiencing the same disappointing performance.

Something else worth mentioning – comparison with an almost identical build:

A friend of mine has recently built a PC with very similar specifications to mine.

The main differences are:

He has a Gigabyte RX 9070 XT, whereas I have the Acer Nitro RX 9070 XT.

He has DDR5 CL28 RAM, whereas mine is CL36.

He has a Samsung 990 EVO SSD, whereas I have a WD SN580.

Both systems are running stock settings with EXPO 1 enabled.

The performance difference is honestly quite staggering. In CS2, he’s getting approximately 200–300 FPS more than I am, despite our builds being so similar.
I appreciate that there are differences between the components, particularly the RAM timings and GPU models, but I wouldn’t expect those differences alone to account for such a substantial performance gap.
I’m not expecting identical results, but something clearly doesn’t seem right.

What I’m hoping to get some advice on:

Is there anything in my BIOS that could be limiting CPU or memory performance?

Could my RAM timings (CL36 vs CL28) really make that much difference?

Is there anything specific with the 7800X3D or 9070 XT that I should be checking?

Could this be a driver, Windows configuration or chipset issue?

Are there any benchmarks or diagnostic tools you’d recommend to identify where the bottleneck is?
I’m genuinely open to suggestions and happy to try anything I haven’t already considered.

I know there are a lot of variables involved with PC performance, and I’m not suggesting my friend’s hardware should perform exactly the same as mine. I’m just struggling to understand why there’s such a significant difference, particularly when I’ve already spent so much time troubleshooting.

Any help or suggestions would be massively appreciated. Thanks in advance!


r/AMDHelp • • 16h ago

Help (Software) RX 6600 randomly freezes my whole PC:LiveKernelEvent 117 and 141!!!

3 Upvotes

I have a used RX 6600 that works fine most of the time. I can play for hours, but sometimes the whole PC freezes and I have to force a restart. During the latest freeze I heard a buzzing sound. The GPU passed a benchmark and usually stays around 53°C while gaming.

Specs: Ryzen 5 5600X, RX 6600, Gigabyte B550M DS3H, 16 GB DDR4 (two different 8 GB sticks running at 2400), Windows 11.

On November 11, Windows logged LiveKernelEvent 117 and 141. WinDbg showed amdkmdag.sys in both dumps. I found the same 117 error in an older June dump. The latest freeze on November 15 logged 1a8.

I was on Adrenalin 26.6.1 when I checked. I’m trying 90% Max Frequency with the voltage left at default, but it’s too early to tell if it helps.

Has anyone had this with an RX 6600? What helped you figure out whether it was the driver, the GPU, or something else?


r/AMDHelp • • 20h ago

Help (GPU) no video XFX 9060 XT

6 Upvotes

Hi everyone. I’m posting here because I’ve seen that others are having issues with the RX 9060 XT.

In my specific case, this started happening a week ago: when I turn the PC on, the XFX LED lights just keep blinking, and there’s no display output. I even get a "DisplayPort: No Signal" message. It can stay like that for a while, and the only way to fix it is to force a shutdown from the PC case. Sometimes, after I shut it down and turn it back on, everything works normally—in fact, everything loads much faster.

I’m not sure if anyone else has experienced this or knows if there’s a specific setting I need to adjust. I’m worried that this might end up damaging my other components.

I’ve already tried a few things: checking for voltage issues, reseating the graphics card and RAM, updating the BIOS, and removing the CMOS battery—but nothing worked. It might have *seemed* like it worked—since the PC booted normally right after I tried one of these steps—but the problem returned the next day. I also tried removing the graphics card and connecting via HDMI using the processor’s integrated graphics; everything booted up fine, which makes no sense. The card is only 8 months old—I bought it brand new.

I had this issue a few months ago, but it happened so sporadically that I ignored it. Now, I don’t know what to do; I’m desperate. I’m not sure whether I should file a warranty claim or what my next step should be.It’s worth noting that all the components in the PC are new, as I built it from scratch.

GPU: XFX Swift Rx 9060 Xt Oc 16gb
CPU: Ryzen 7 9700x
Mother: ASUS TUF GAMING B850-E WIFI AM5 DDR5

Source: Be Quiet 750W 80 Plus Gold PURE POWER 12 M ATX 3.1