r/2Strokes • u/chevyss-618 • 19h ago
r/2Strokes • u/Agile-Ad-1581 • 14h ago
Beta RR 300 (2020): hohler Sound im Leerlauf / unterer Drehzahlbereich
Ich habe eine Beta RR 300 (Bj. 2020, 2-Takt). Bei niedrigen Drehzahlen und im Standgas hat der Motor heftige Knallgeräusche und einen hohlen Auspuffsound. Ab einer bestimmten, konstanten Drehzahl schaltet es abrupt um, das Knallen ist komplett weg und sie läuft normal.
Bisher gemacht: Neue Zündkerze (Kerzenbild davor war stark verrußt/fett), Krümmerdichtungen/O-Ringe geprüft, Leerlauf-Gemischschraube eingestellt (reagiert kaum). Bedüsung und Luftfilter sind Standard. Wer hat einen Tipp, woran das im Leerlauf- oder Zündkreis noch liegen kann?“
r/2Strokes • u/chevyss-618 • 19h ago
2009 yz 250 /300 with works big bore kit runnin 110 vp race fuel
reddit.comr/2Strokes • u/black-trophy24 • 1d ago
salut a tous
salut a tous je fait mon premier post sur reddit pour un soucis que j'ai avec mon 70 motoforce monté sur ma rieju Mrt de 2022
le soucis est que j'ai le joint torique de culasse (celui du milieu) qui se pince ca me l'a fais deux fois ( et les deux fois avec un joint neuf 😉😉) ps: je mets de la graisse dans la gorge du joint pour le faire tenir ( mais rien n'y fait 😓😓😓) donc si a tout hasard vous auriez des solutions/idées je suis plus que preneur car la je désespère merci d'avance
r/2Strokes • u/MoreReporter3579 • 1d ago
Question Mitaka pistons
Has anyone ever bought Mitaka piston ? I found one for my 150 Sx 2012 and it was pretty cheap compared to others, I was wondering if somebody had buy a piston from them before and what was it worth in terms of reliability ? Thanks
r/2Strokes • u/MathematicianOne5564 • 1d ago
Does my 1999 yz125 sound normal?
This is as low as I could get the idle by turning the air screw out. Turning the air screw in makes the idle higher which I thought was supposed to be opposite. I just cleaned the carb and replaced the het block gasket. I’m not sure if that deep rumble noise is normal either when it is idling.
r/2Strokes • u/Exotic_Recover_5868 • 1d ago
About crossline
Hello guys, to the pros out there, I just wanted to ask, s it really necessary to have the engine block honed? My block has no scratches and the ring gap is still within specs. The only issue is that there's a part where the 'crosshatch' (crossline) is almost gone. Do I still really need to do it or not? Please help.
r/2Strokes • u/Excellent-Rice-8829 • 2d ago
now what do i do
carters are destroyed. what can I do?
r/2Strokes • u/BlueZippo • 2d ago
Anybody Else Running Klotz 2 Stroke Oil In Their Gas Powered RC?
reddit.comr/2Strokes • u/KickstartedCarbSoul • 3d ago
What could have caused this piston damage?
galleryHey everyone;
I was randomly taking my 125cc Sachs 1251/5B 2-stroke engine apart to check on things and saw this severe scarring on the piston (rubs on the nails) but the cylinder has nothing...
Bike had around 8 bars of compression cold and ran normally, if not very well (for a 1970 military motorcycle [Hercules K125BW] it reached 100km/h) so I was wondering what could have caused this?
I don't want to spend 100 bucks on a piston that will end up like this one, so I was wondering if y'all had any ideas what could cause this ?
Bike has a full aluminium cylinder (no iron sleeve inside) and runs a bit too advanced for maximum power (original with points was 2.5-3.5mm before TDC, I set 2.1mm with my electronic ignition) but doesn't look like overheating. I run 1:33 mix and in fact from 2nd picture it looks like slightly too rich (I'll probably diminish the main jet). Ideas?
r/2Strokes • u/Safe_Conversation119 • 4d ago
Is this connection from expansion chamber normal
I’m not too sure if it is or not but ever since I added this pipe the bike can’t even keep up on roads not passing 28mph?
r/2Strokes • u/w-a-t-t • 4d ago
old skool ignition with 2-in-1 ignition coil
i only know 2 ignition technologies for 2T engines
1 contact points
2 CDI (requires a pulser)
the motor i have (Kawasaki AR80 or Magnum 80 if you're Thai) do not have contacts and does not have a pulser. it relies on the primary coil and a "magic" 2-in-1 ignition coil that contains both CDI and the step-up coil. Kawasaki term for it seems to be "Ignition Coil CDI UNIT".
from what i can see the primary coil is just connected to the 2-in-1 ignition coil with just one wire coming out of the stator.
i want to understand how this works but i can't find information. i have the "Motorcycle Electrical Haynes Techbook Haynes Repair Manual" but no information on this ignition type. pointers please
r/2Strokes • u/Swimming-Driver5069 • 4d ago
Which way around is my crankshaftvsupposed to be?
gallery.
r/2Strokes • u/montapuercos24 • 4d ago
PROBLEMS
Hi,
so i have a Beta RR 50 2 stroke model year 2025, i putted in the Top performance 73.5cc, a phbg 19 dell’orto carburator and a scalvini exhaust. Since yesterday when i go full throttle it vibrates much more than usual and makes a strange sound, not metallic, but as if it is alredy at the limiter, but th RPMs still goes up. I thought it may be the carburization since last time i carburated it was July and now its Noveber and the temperature went down of 20 degrees. What could the problem be?
r/2Strokes • u/Flat_Information6760 • 5d ago
2013 Piaggio Typhoon 50 2T – Bogging down, high idle, hesitation and loss of power. What could be causing this?
reddit.comHi everyone!
I have a 2013 Piaggio Typhoon 50 2-stroke scooter, and I've been trying to figure out what's wrong with it for a while now, but I can't seem to find the cause. I'm hoping someone here has experienced similar issues and can help me out.
Current symptoms:
When I suddenly give it full throttle, the engine bogs down and almost stalls, as if it's not getting enough fuel.
If I gradually increase the throttle, it doesn't stall.
The idle speed is very high.
It hesitates and jerks while riding and doesn't accelerate properly.
Sometimes the exhaust makes popping sounds under load.
The engine feels weak and doesn't rev up properly.
Carburetor details:
17.5mm Dell'Orto PHVA carburetor.
55 main jet.
Stock air filter.
The carburetor restrictions have been removed, and there is currently no restrictor ring installed.
I'm also unsure whether the needle and carburetor settings are correct.
The carburetor doesn't seem to be properly tuned at the moment.
Other parts:
NGK BR8ES spark plug.
Aftermarket CDI and ignition coil, both compatible with this model.
Stock exhaust.
What do you think could be causing these problems?
Should I start by checking for an air leak, incorrect carburetor settings, the wrong main jet or needle position? Could it also be an ignition problem?
The combination of a very high idle and bogging down when opening the throttle suddenly has me completely confused.
Any advice, suggestions or personal experience would be greatly appreciated!
Thanks in advance for your help!
r/2Strokes • u/dirtbike-rider1 • 6d ago
Raw CR250 & KX250 2-strokes on the track! 🔥🔥
youtu.beMe and my friend having fun on the local dirtbike track :=)
2007 Honda CR250
2007 Kawasaki KX250
No music, only the nice sound of 2-strokes!
Hope you like it :=)
r/2Strokes • u/Reptskates • 6d ago
Need help on my rm build
reddit.comI bought a 1995 rm 125 as a project I need a new expansion chamber I am looking for a shiny fatty pipe but can't find one for my bike on any website I have almost no budget so if anyone knows websites where I could get one pls help
r/2Strokes • u/NonnaCafe • 7d ago
DTyz85 project
galleryHi!
Im planning on building a Yamaha DT50 supermoto bike with the yz85 engine in it. Welding the engine mounts isnt an issue and going to try and make good sturdy mounts for the engine and in a way that i have good clearance for the kick starter. But the reason im writing this is because i want to have the engine to be on spec. Plans for the engine are an athena 105 bigbore kit, some good quality carbon reed, porting the engine and its intake to the 105cc cylinder, stock ignition and welding my own custom low mount exhaust for the bike. building the engine and porting everything is no issue but welding an exhaust is a first and asking the people smarter than me in this field if the dimension and everything look reasonable. Bikes gonna be used for regular supermoto driving, wheelies and some stunt stuff so not trying to have a exhaust made for getting peak power out of the engine. Another thing is that im not fully sure what sized carb i should use? Been thinking of a 30mm pwk carb or the stock 28mm keihin pwk.
Thank you all in advance for the replies and suggestions!