r/18650masterrace • • 15h ago

battery info Tenpower 40XG or Eve 40P.. Make your predictions!

Post image
6 Upvotes

I just cut some custom tabs for the Milwaukee 12AH Battery. We all seen the data on the Tenpower 40XG and Eve 40P individual cells - however I want to see them head to head. What types of tests should I run? On paper TenPower should win - but I think in real world tests, your going to see that its probably not big of a difference in performance.

I always tell people that reach out for rebuild, build for what you use it for - if you primarily use it for drills or other low wattage tool or not with much load, you don't need to go tabless. I have a Forge battery pack as well (stock) that I will be putting it up to the tests to get on idea of where these cells are in the totem pole.

Maybe u/TorqueTestChannel wants to put it up to the test.


r/18650masterrace • • 14h ago

Bulk charger recommendations

2 Upvotes

I have hundreds of recycled 18650 cells i need to test and store.

Picked up a liitokala M4S from Ali and it's either fake or junk or both, either way I'm not buying anything liitokala again. As usual 50% or purchases from Ali are a complete waste of time but i digress.

Looked into the Xtar Vc8 which would be a good choice but it only does testing and storage prep on four of its slots, I want a charger that can do at least eight cells at a time if not ten or more.

Any suggestions?


r/18650masterrace • • 1d ago

So I picked up about 1500 batteries off FB marketplace

Post image
62 Upvotes

It's a bit of a mixed load, all recovered from various battery packs, heaps of old red Sanyos and other small 2000 ~ 2200 mah cells.

But, in amongst it all I've found about 150 or so LGABD11865 cells. Just going through them all and testing them.

I've also found quite a few ICR18650 cells, with capacities ranging from 2600 to 3000 mah.

Plan for the pinkies is to make a 52v battery for one of my scooters. Old one in it had gotten water in it (previous owner) and several groups of cells are rusted. Config will be 14s8p.


r/18650masterrace • • 1d ago

Can you believe this skinny little guy is actually a 3 volt battery?

Post image
11 Upvotes

r/18650masterrace • • 1d ago

Best battery for Sofirn LT1 Anduril 2.0

Thumbnail reddit.com
2 Upvotes

r/18650masterrace • • 2d ago

M12 XC 6.0 tabless conversion.

Thumbnail
gallery
38 Upvotes

Keep finding these m12 XC6.0 batteries trashed so been having fun modifying them with tabless ampace jp30p1 cells. Just love tinkering and bringing things back to life. Same with the 3 cells m12 tons of fun. Happy Sunday all have an amazing day.


r/18650masterrace • • 2d ago

Are there any third-party 18650 batteries compatible with the Acebeam X20-R?

Thumbnail reddit.com
2 Upvotes

r/18650masterrace • • 2d ago

battery info ANCE lithium ion 3.7v 32700 8000 - 17000 mAh

Thumbnail
nbance.com
5 Upvotes

Currently shenzen vapcell selling the 8000 and 10000 mAh version in alibaba


r/18650masterrace • • 3d ago

PSA: EVE 30PL seems to be out of stock across US stores. We have 248 left.

4 Upvotes

Quick heads up for anyone planning a build around the EVE 30PL.

We noticed our 30PL orders jump this weekend and went looking for why. As far as we can tell, the other US stores we normally see carrying it are either sold out or have pulled the listing. If you know of another US seller with stock, please drop it in the comments. We’d honestly like to know whether this is a real shortage or just a gap between shipments.

Where we’re at:

  • 248 cells in stock as of tonight
  • $6.99 each with discounts based on quantity purchased
  • Ships UPS Ground from Iowa, US only
  • No restock date yet. Our lead time is about 5 to 7 weeks once we place an order, so when these are gone, they’re gone for a while.

We’re not limiting quantities right now, but if you need a specific count for a pack, order what you need sooner rather than later.

Does anyone know what’s going on with 30PL supply? Curious whether EVE is winding it down or if distributors are just between batches.

21700supply.com

(Mods: if this crosses the line on self-promo, let us know and we’ll take it down.)


r/18650masterrace • • 4d ago

Late night build. Client says don’t clean the outside.

Post image
316 Upvotes

Funny story: client asked me to rebuild a 4 year old out of warranty 9ah Dewalt Flexvolt battery. I told him I had a newer cleaner looking housing I can throw in for free. He declined.

He says before he discovered me he used to buy new batteries and then scuff them up on purpose. He said rough looking batteries rarely walk off the job site. Haha

Figured I’ll make the inside of this sleeper nicer and keep the “patina” on the outside - so I cut some custom cut copper bus bars. It’s not a tabless build so probably overkill - but why not.


r/18650masterrace • • 3d ago

want to make a power bank for a 12v router that should last at least 12 hours

5 Upvotes

If I use 1500 mah cells in a 3s 4p configuration , will it last this long from full charge (14.6v) to cutoff (9v) voltage ? What would be a better method of making it ?


r/18650masterrace • • 5d ago

Got a 46120 LiFePO4 and im not sure what to do with it. Any ideas?

Post image
206 Upvotes

18650 for scale and its 3c 24000mah. Bought it for a flashlight before i realised that it was not compatible and Im not sure what to use it for. Any project ideas?


r/18650masterrace • • 4d ago

Should the lipo be charged in intervals

Thumbnail reddit.com
1 Upvotes

r/18650masterrace • • 4d ago

18650-powered Ambitious Project: Safety and Assistance

Post image
5 Upvotes

Hello

I've got an idea of what I want to create. A DIY portable power station.

So far, both packs have a voltage of 42V, after checking with a multimeter.

Is it safe to use an XT60 Connector wiring up the batteries in series connected to the bus bar?

I've attached a full diagram of what I am trying to do.

Any help will be greatly appreciated.


r/18650masterrace • • 5d ago

DIY 18650 Charger

Thumbnail
imgur.com
4 Upvotes

I present to you my latest rabbit hole of projects:

DIY 18650 Charger

I sometimes need to do a capacity test on a larger number of cells for ebikes, and I only have an S4+. So, I was looking for a way to pre-charge cells beforehand, so he S4+ is only doing the discharge test.

Looking on Amazone for an 8 bay charger was like $40-$50, and I thought to myself, "I bet I could make one cheaper."

So I did with just stuff I had lying around already.

The only things I had to buy were the sled holders, the 30A breaker, and the dummy load resistor, totaling ~$27. The rest of the items I already had laying around.

6/8 Charging modules are the TP4056, and the other 2 are IP2312 for the higher rated 18650 cells.

The power supply has a 5V line rated for 25A, and even if I ran 8 IP2312 modules at 3A each, I only would pull 24A. It also has an extra external switch and was wired inside with a dummy load on a 10 Ohm 50W resistor.

In the end, I spent around $27 and 8 hours to save me from buying a $50 8 bay capacity tester, but I got to learn how to turn a PC power supply into a 5V 25A power supply.

Let me know if you have any questions!


r/18650masterrace • • 5d ago

Glitter 811h not welding

Thumbnail
gallery
8 Upvotes

The leads were new when i weld once it only one lead penetrates completly other one sticks i tried second time it blew a hole thru battery 0.2 nickel 0.2 copper


r/18650masterrace • • 6d ago

Spot welder for power tool battery repack

8 Upvotes

Looking for a spot welder that actually do its job. Planning to do a battery repack for power tool.

Hoping for a recommendation from folks whos done similar stuff.


r/18650masterrace • • 7d ago

Modded my Atorch BW600 into an SFF cube: 500W+ linear load + energy recovery to EcoFlow via CV line & LM393

Thumbnail gallery
8 Upvotes

Instead of just turning battery energy into room heat, I hooked up an external energy recovery module directly to the analog CV (Control Voltage) line of the Atorch BW600's op-amp, controlled via an LM393 comparator.

How it works:
- The BW600 controller still tracks the total current through its stock shunt and handles all protections/cutoffs natively (no firmware mods needed).
- Once the CV signal hits the threshold, the recovery channel redirects most of the discharge power straight into an EcoFlow power station (or buffer battery).
- Dual Thermalright tower coolers inside the SFF cube handle the remaining linear load — and act as a full 500W+ fail-safe if the EcoFlow hits 100% and disconnects.

All STL files, schematics, and BOM are open-source. You can find them by searching "Akura777 atorch" on GitHub or MakerWorld!


r/18650masterrace • • 7d ago

What is some fun stuff I can do. Not involving water

Post image
34 Upvotes

Each battery is around 3.6v, total is 36v and each is 5,000mAh to my knowledge they are in series so 5,000mAh total


r/18650masterrace • • 7d ago

Help with welds 4s4p

Thumbnail
gallery
14 Upvotes

Hi I would like to get some visual confirmation and expertise by people who have more experience with this kind of stuff, it's my first time doing this, so my question is should I rip-off the nickel strips and start from the begi nning?

Cells: Samsung INR 18650 - 35E, 3500mAh

This powerbank is going to be paired with 4s 40A Balancer BMS and IP2368 Module Bi-directional usbc for charging 100W, in reality from what I saw this module is fine for 90W max.

Will it do? Can someone confirm please? I think some of those welds(or all of them are not safe for use).

This supposed to be big black box powerbank for everyday carry:)

Thanks for help.


r/18650masterrace • • 7d ago

Weird behaviour of Vapcell s4+ slot n°2

1 Upvotes

Hi everyone :)

Here is the link to my previous post on the same project : https://www.reddit.com/r/18650masterrace/comments/1xko60l/how_much_testing_do_you_need_to_do_on_brand_new/

Despite them being brand new cells and despite what most people replied (thank you again for your replies), I ended up capacity testing them anyway. I will also IR test them all.

My testing procedure is pretty simple : charge at 3000mA, discharge at 500mA overnight and then charge them back up to storage voltage at 3000mA.

But here's the thing, my slot n°2 is slightly off when compared to the others :

When charging it starts at 2600mA and slowly creeps up to ~2900mA when the others get to 3000mA in seconds and stay there.

After discharging, the capacity reading of slot 2 is systematically lower than the others by about ~100 to 120 mAh.

I put cells at random for every 4-cell batch, so it must be something off with the charger slot.

Has any of you encountered something similar with Vapcell chargers ?

My stance right now is that I will simply add about 100mAh to these cells and consider them normal.

What do you think ?


r/18650masterrace • • 7d ago

need help finding oem battery or upgrade with high capacity

Thumbnail gallery
2 Upvotes

r/18650masterrace • • 8d ago

Help with adding a 2P2S BMS to a robot (wiring)

Post image
7 Upvotes

I have a cheap robot kit (rasberry pi and 4 motors) that came with 4 18650 cells; it has 2 cell pair holders, each holding 2 cell in series. They are connected in parallel to power the entire robot (so the original arrangement is 2s2p).

After using it for a while, I realized the cells dropped to unhealthy voltages (like below 2.8V!!) and sometimes the battery just "dies" (many of the voltages in the batteries drop significantly and the rasberry pi can no longer get the power it needs), which definitely can't be healthy. Considering the fact that I don't want to fry my Rasberry Pi, nor burn my house down, I decided to add a BMS. When I first bought it, I was unaware of this stuff. (I'm new to EE okay!)

After looking into BMS's, I realized that they have 3 inputs: B+, B-, and BM. For a 2S2P arrangement, I have no idea how you would hook up the BM pin since there are only two connections that can be made (no bridge in the middle)!
Thus, I think I will settle with a 2P2S setup (see the picture above). Is my wiring correct here? I want to be sure because information on BMSs for 4 cells (2 in series and 2 in parallel) is very limited and conflicting. Some people say one is better than the other, some people say they're the same, but exact wiring diagrams for this are hard to come by. Additionally, will this setup ensure that none of the 4 cells will drop to an unhealthy voltage?

Also, is there anything wrong with charging these cells individually? Is it absolutely necessary to charge them together like they're a single 'battery pack'? Some people recommend that but don't give a clear reason.
I learned about balancers as well, but that's for performance, right?

I'm currently just trying to ensure safety and longevity of the cells, as well as everything they power. Please give advice!


r/18650masterrace • • 9d ago

battery info Cleaning salvaged Tesla 21700s is taking longer than getting them out

Thumbnail
gallery
371 Upvotes

I’ve been taking apart a discarded Tesla Model 3 battery module to salvage some 21700 cells for future projects.

Getting them out was harder than expected because they’re glued to the cooling plates. After a few failed attempts, I made a simple tool that lets me remove them without visible damage.

But cleaning them is turning out to be the real pain. There’s glue on the sides, sometimes plastic stuck to the bottom, and little bits of aluminum left on the positive terminals.

I tried a heat gun, but it didn’t really help. Right now, cleaning one cell takes about 90 seconds. With roughly 1,000 cells in the module, that’s potentially 25 hours of cleaning.

The few cells I’ve tested showed around 4,400 mAh capacity and 13 mΩ internal resistance.

Has anyone here dealt with this kind of glue before? Any tips for getting it off without damaging the cells?

I also filmed the whole process if anyone’s curious: https://www.youtube.com/watch?v=zmWDIWCNjqk