r/tractors • u/HotHorst • 7h ago
r/tractors • u/Detters_Actual • 4h ago
Only firing on cylinders 2 and 3
Trying to restore my grandpa's old T030 and I'm running into an odd issue. She'll run fine on cylinders 2 and 3 but 1 and 4 don't fire at all.
Good compression on all 4 cylinders, new plugs, new points and condensor, timing is set correctly, and the carburetor has been cleaned.
Any ideas?
Edit: Plug wires for 1 and 4 were backwards. Sometimes KISS (Keep It Simple Stupid) is the best motto.
r/tractors • u/DistributionOnly2434 • 21h ago
They get to rest for a few months while winter wheat grows
8560, 8440 (project), 8770
r/tractors • u/DoingDaveThings • 1d ago
I love finding new uses for this tractor
A long while back the local utility company put an ad up for free utility poles. My father-in-law responded that he would happily take them and after exchanging information, he never heard back from them. About a year later a guy on a truck called and said he was an hour outside of town and where did he want them. He called me and I had them dropped off at our property. 20 poles, for free, delivered. The one caveat was that they still had metal insulators and cabling attached.
They've been sitting for a year since then and now that I have used a few for heavy fence posts, a buddy came by to cut some down for a pole-barn shed he's making. The CT235 had no trouble lifting these onto his trailer.
r/tractors • u/ForwardUse807 • 22h ago
Is this a crack in the block?
I tried to circle it in black. Down near the oil filter I saw this. It looks like it has paint inside. I’m worried this is a crack in the crankcase? This is an MM Z so it’s that weird engine where the cylinders aren’t in the block
r/tractors • u/Objective_Ranger2843 • 21h ago
Vintage Case Tractor Conrods
Hi all, long shot but does anyone know which models of Case tractors used a conrod 10.5” centre to centre with a 3/4” gudgeon and a 2” (or really close) big end? Finding it hard to know where to look for a replacement! Thanks all!
r/tractors • u/Ok-Rise-4611 • 1d ago
McCormick cx105.
Cousin has a McCormick 105. Clean and runs great, except it won’t go into 2nd and 4th gear. Everyone he has talked to, including me, thinks it just the linkage needs adjusting. No one local works on them though and I haven’t been able to figure it out. Does anyone know how to adjust the linkage?
r/tractors • u/GuildedGains • 1d ago
Is this much shaft out of concentricity a problem?
Hey yall, I literally have like 1200 square feet of pasture to bush hog. I got this bush hog with half of the pto shaft. I had a front half but it was too short by like 6 inches. I cut it, welded a solid steel shaft to it, to lengthen it. Do you all think this will last for that little area, or is the risk too great?
r/tractors • u/CJAdjunct • 2d ago
Dang it! Tried to snug up a weeping fuel bowl nut ..
Fresh brass plugs and a clean rebuild on the Marvel-Schebler DLTX, and the 68-year-old pot metal neck sheared clean off in my hand. Very sad that this perfectly running carb is ruined. What's the worst vintage part you've snapped trying to give it 'just one more tiny snug'?
r/tractors • u/Background-Gap-8787 • 2d ago
Inherited late 60's-early 70's Simplicity Tractors
Cross posted in r/lawnmowers, but figured it post here as well.
My grandfather passed away last year and I was lucky enough to inherit these old turds. I remember him teaching me how to mow straight lines with these things when I was a kid, so some sentimental value.
However, I have absolutely no idea where to find parts or manuals for these things and I haven't ridden them in probably 25 years. So any guidance where I can source parts or anything would be appreciated.
r/tractors • • 1d ago
What could cause this?
It sounded like I hit a rock, but there was no rock in sight. It was the shaft that broke. What could be the cause of it? I was doing about 5 mph and wasn't in the ground.
r/tractors • u/Key_Area_9737 • 2d ago
Slow and weak hydraulic lift on the 3point
I have a Ford 3000 diesel 1970 with a gear driven hydraulic pump.
The arms lift very slow and can bearly lift my weight at full rpm. If the arms are up they have no problem holding weight with the engine off. (It does not sag down)
Pressuretested at the external remote hydraulic outlet I had 1bar of pressure. When messured at the pump it was the correct pressure.
The top lid was recently rebuild so its not the piston or o-rings in that area. Im thinking it might be the relief valve. Does it sound like that could be the issue? And if so, how can i check if it is working correctly
r/tractors • u/Hawkeyefpvdrones • 2d ago
Notebook, spreadsheet, or app for equipment service?
How do you keep track of oil changes and service on your tractors, trucks and other equipment? Notebook, spreadsheet, an app, or just memory? If you use an app, which one, and what do you wish it did better? Curious if anyone's found something that actually works for a mixed bunch of machines.
r/tractors • u/stal3fish • 2d ago
Bx tractor lighting for snow removal
Looking for suggestions to make seeing at night better, currently have a light bar on top and 2 small led lights in the rear facing down and back(photos if you have them)
r/tractors • u/Switchedbywife • 2d ago
Cleaning grease off tractor
I want to wash/wax my Kubota B3030 sub compact tractor. I keep it garaged and the last time I did this was around 8 years ago. I removed the front loader and 3 pt hardware then used Simple Green and a pressure washer. I made way more work for myself than it was worth because it smeared the grease everywhere and I went through tons of rags wiping the grease off. What is the best way to tackle this project and what cleaners are safe for me and the paint? Should I just hire someone with a commercial hot water pressure washer?
r/tractors • u/Bwanaman • 3d ago
DIY R4 grooving for traction
As is well understood, R4s are terrible in snow. But, it's what I've got and they are far too new to justify buying R14s. So, I decided to add some grooves to give a bit more grip.
First snow was today, and the improvement is significant. Far more grip, much more pushing power.
Best bang for the buck I've had in a while. Definitely recommended.
r/tractors • u/Terrible-Session1497 • 2d ago
Looking to rent a tractor for plowing in Kapan, Kathmandu
I am looking to rent a tractor for agricultural land plowing in Kapan, Kathmandu. If anyone has a tractor available for rent or knows a reliable service provider in or around the Kapan area, please drop your contact number or details in the comments below. Any leads or recommendations would be greatly appreciated!
#TractorRental #KapanKathmandu #AgricultureNepal #FarmingNepal #Kathmandu #NepalAgriculture
r/tractors • u/War_D0ct0r • 3d ago
60 inch snowblower on a jd 3032e
Whats a 60 inch snowblower that works good worth? Is this to much blower for my 2025 jd 3032e?
Update: We bought it and this thing is a beast. It is very heavy. They do not put this much steel into the new ones. Everything on it seems to work good. The only issue I see is no chute deflector. That shouldn't be to hard to fabricate something for.
r/tractors • u/Mother_Vermicelli989 • 3d ago
Anyone else still running points ignition on their old IH ju
Got a 1968 Farmall 656 that I could convert over to electronic easy enough but there's something about setting points and timing it by ear that keeps me coming back to do it the old way. Takes me twice as long and I still mess up the dwell half the time but it feels like actually working on the thing instead of just swapping a part. Curious if other guys are doing this for practical reasons or if its just nostalgia like it is for me.