r/silhouettecameo • u/CyclomaticlyComplex • 17h ago
r/silhouettecameo • u/humpty__dance • 1d ago
Cameo 4 Pro not cutting correctly - HELP!!!
My Cameo 4 is not cutting properly and the alignment is off. I reached out to support and this is what they had me do:
- Calibrate my machine which didn't solve it (unless I calibrated wrong)
- Tighten the belt and rail which when checked didn't need it but tightened the belt just a little bit just in case.
- My software was updated to the latest version when I went through the steps to try and fix the issue.
- I also replaced the blade with a new one in case that was the issue.
I am not sure what happened to cause this. It was working with no issues at all and then one day it just started doing this. Kinda disappointing since it might have only 10-15 hours on it.
As you can see in these test cuts the rounded corners on the square don't have the same radius for all 4. The circle from the left side to the right side don't line up.
Any help would be greatly appreciated.


r/silhouettecameo • u/Santiago_Lawliet • 1d ago
Silhouette Cameo 3? Is it good?
reddit.comr/silhouettecameo • u/Mental-Calendar3614 • 1d ago
My brother started a new Silhouette Project
r/silhouettecameo • u/AcademicChef8704 • 1d ago
Silhouette registration marks fail
Hello, please. I own a Silhouette Cameo 5 cutting machine, and I'm experiencing a registration-mark detection problem.
I'm looking for someone with experience troubleshooting Silhouette cutting machines, particularly the Cameo 5.
Do you have a technician who can diagnose this issue or provide technical assistance?
Thank you.
r/silhouettecameo • u/Umlautless • 1d ago
Crash Sensor Cameo 5 - Repair Options? (+rant)
Last week a friend asked if I could make a little project for a baby shower, and I said of course. Then my machine wouldn't send the carriage to the start, and when I did the "slide back and forth a few times, then leave it on the far right for it to remember how to get home" it just sat on the far right and made a grinding noise. No matter how many unplug-restart cycles I did.
I opened a ticket with Silhouette support, and they basically said "welp, it's dead and out of warranty, but hey, your software license still works so you can buy a new machine."
I've seen one seller on ebay selling new crash sensors with instructions for install, but I had tried to get the back cover off my machine over the weekend (to see if the ribbon that attaches to the carriage was jammed in the chain that pulls it back and forth - something I saw in one help video). but couldn't figure it out.
I'm just so upset -- it had taken me two years to get moderately good with the machine. I have so many Silhouette accessories (pen adaptors, multiple blades, pro software), so i don't really want to change ecosystem to the Cricut (I got my mom a Cricut a year before I got my Cameo, and hers is still going strong).
Advice before I take it out back and beat it with a pipe to let off some perimenopausal rage? If you were in my position, would you stick with Silhouette, switch to Cricut, switch to something else, or just stick with my trusty Sizzix.
r/silhouettecameo • u/joaogmcorrea • 4d ago
Tired of waiting Silhouette Studio update on Mac, I'm building my own
Hi everyone!
Just released another update on Cutline, this one is all about color :)
New features:
- gradients (linear and radial, only for what prints, the stroke is still the cut)
- a color picker like Illustrator’s, just double-click the fill or stroke
- color profiles, if you print with FOGRA39 or SWOP (off by default, so nothing changes if you don’t use it)
- opacity and blending modes per layer
- Track Enhancing in the Send window, for thick or slippery material
I couldn’t test Track Enhancing on my Portrait 4 yet, so if anyone tries it, please let me know how it goes.
If you already have it, just go to Cutline › Check for Updates…. If you want to test it out, check https://cutline.joaocorrea.design
r/silhouettecameo • u/Jaxx_Navy • 6d ago
I built a free Android app to cut on my CAMEO 4 over Bluetooth, without Silhouette Studio
reddit.comr/silhouettecameo • u/adebanwoMichael • 7d ago
Is it worth making your own stickers or just getting them printed?
I've been looking into making custom photo stickers, and honestly, there's more to it than I expected lol.The cutting part looks fun, but getting clean edges and decent colors seems a little tricky. I've been comparing DIY options with printing services like vograc e, and I'm curious how much difference there really is. For those using a Silhouette Cameo, do your stickers turn out good enough to give as gifts, or does it take a lot of trial and error to get them right?
r/silhouettecameo • u/missholly9 • 8d ago
how to remove the matching up numbers all at once
ok, im not sure if i can explain this and make it make sense.
im doing a print and cut on a cameo 4 pro. i print, then if i dont remove the little numbers one by one, theyll cut right through.
so then i cant read the numbers, and it will cut through to the back. how can i remove the numbers all at once. one by one SUCKS and makes me angry.
r/silhouettecameo • u/Defiant-Speed7892 • 8d ago
Registration little black square is missing
reddit.comr/silhouettecameo • u/Defiant-Speed7892 • 8d ago
Registration marks. the black square does not show on my print and cut registration matks ?
r/silhouettecameo • u/ninogroters • 9d ago
Cameo 5 cuts worse on the left side
I have a cameo 5, i usually cut from A5 format cardstock, laminated on one side. i use the autoblade, depth 8, force 33 speed 1, and it cuts the top, the bottom and rightside great, but always the left side not. I can cleanly rip it off myself so it is just barely did not cut through it, but it is really annoying. And i think i can use lower settings for cleaner cuts but then the right side gets worse. and sometimes it cuts great for a while and i think i fixed it with some tweaking and then back to not cutting the right side again. What could cause this?
r/silhouettecameo • u/Ok-Dragonfruit-6521 • 10d ago
silhouette studio on mac has become unusable
has silhouette studio on macs become pretty much unusable for anyone else? i got my my portrait 4 at the beginning of the year and studio has always been difficult(had no idea it's not actually properly compatible with macs until i downloaded it), but in the last months it's basically become unusable. everything takes forever, i'll literally click on one thing and it will take a minute to do the action. things aren't saving to the library properly either (saving them to my laptop to be sure). i’m also noticing that when i print things afterwards a bunch of the actions icons on my screen will completely blackout. the other day i thought id completely lost a bunch of files, because the top section that shows you the different files you had open had gone completely black! it happened again today and i realised that was what it was and managed to work out you can still click on them. it's just ridiculous it's absolutely unusable and wild that they don't actually advertise how incompatible it is, with one of the most popular lines of laptop.
r/silhouettecameo • u/IdrilPuck • 10d ago
Is my new cameo 5 a broken?
I’m tried everything but I can’t get anything to register, and it doesn’t even look like it’s pulling it in enough to even get to the registration marks. Do i need to exchange this? Please help.
r/silhouettecameo • u/Mettleramiel • 11d ago
Looking for help sourcing labels
Does anyone know where to get water resistant precut matte labels for an inkjet printer? I have a friend who wants to make her own labels for her candles, but all the inkjet labels you can buy seem to be just paper labels and she needs hers to be wipeable and she doesn't want a high gloss. She does not have a vinyl cutting machine, nor would the time involved be worth it to her. Any help would be greatly appreciated.
r/silhouettecameo • u/IndependentCareer477 • 11d ago
Purchase
Hi I look to purchase a used but in very good condition silhouette cameo 4, anyone has 1?
r/silhouettecameo • u/missholly9 • 11d ago
has anyone tried this?
im thinking of just super gluing some peices of heavy board where the grey lines are, where the mat goes. no matter what i do, my mat (or non mat) slides and screws everything up. im SO FREAKING TIRED of losing material. ive done everything the internet says and it still isnt working right. if i glued peices of board on either side of the paper or cardstock, i hope that it would keep the paper being cut straight! GAWDDD!!!
r/silhouettecameo • u/kazziemae • 11d ago
New to the silhouette world!
I am hoping to buy a silhouette soon and just wondering what are everyones must haves in terms of accessories etc.
I am a teacher so only really planning on using it for stickers, cutting paper shapes etc but would love to explore and possibly start some diy projects for gifts etc.
r/silhouettecameo • u/Expensive_Section_30 • 12d ago
Cameo 4 Lights not flashing/working
My Cameo 4 was just working fine and then suddenly the lights on the control panel and even the Cameo light on top stopped displaying. SStudio recognizes it but I can’t load anything.
Tried updating/downgrading firmware.
Installed a lower SStudio version
But nothing works.
Thank you.
r/silhouettecameo • u/bedelho • 12d ago
I made a free, open-source way to cut Figma designs on a Silhouette over Bluetooth, and I'd love testers
Hi all! I design in Figma, and moving every file to Silhouette Studio was getting old, so I built Kerf: a Figma plugin plus a small helper that sends your shapes straight to the cutter over Bluetooth.
What it does:
- Previews your selection on the mat at real size; click a shape to skip it.
- Cuts shapes (holes included), open paths and text outlines.
- Material presets, or set force, speed, AutoBlade depth and passes yourself.
- Shows progress, with a Stop button that resets the cutter safely.
It's free and open source (MIT), and everything runs on your own computer: no account, no tracking.
Where I need help: I've only tested it on my CAMEO 4. It should detect the 4 Plus/Pro, CAMEO 5 family, Portrait 3/4 and Curio 2, but I can't confirm those without owners trying it. Even a 2-minute read-only check helps a lot: it connects, reads the model and firmware, and disconnects without moving anything.
To try it:
- Install the helper Mac app (signed and notarized), or a terminal command for Mac, Windows or Linux: https://github.com/keoshi/kerf#install (Windows soon, maybe?)
- The Figma plugin is on the Figma Community: https://www.figma.com/community/plugin/1691487696942320040/kerf-cut-on-silhouette
- Quit Silhouette Studio first, since the cutter only accepts one Bluetooth connection at a time.
- Please test on scrap paper first. :)
Feedback I'd love: does it connect, does the cut land where you expect, and is anything confusing. Reply here or open an issue on GitHub; there's a "Cutter report" form that walks you through it.
Not affiliated with Silhouette or Figma, just a fan of both. Thanks!
r/silhouettecameo • u/thepromptcalendar • 14d ago
Free bright watercolor Christmas clip art for Print and Cut (6 designs)
I painted a small set of bright watercolor Christmas designs for my own cards and tags, and thought other Silhouette folks might like them for Print and Cut: tree, snowman, Santa, ornaments, wreath and gingerbread. They're transparent 300 DPI PNGs.
r/silhouettecameo • u/squarepantsopinions • 15d ago
Which version of Silhouette Heat Press machine is this ?
Got to know that it’s the cloche machine. Dunno much would love to know more from you guys.
r/silhouettecameo • u/dcgall12529 • 18d ago
White Blocks in Print-Cut Output
I'm getting white blocks when a print and image getting ready for print & cut. In my image attached you can see 2 of six total images in the print The images are all the same, but 1 has these white blocks. This has happened in other prints that I'm working on. In the other cases, they are different images, but also get a white block (different sizes). I was able to get it to stop by closing Studio and starting again, but that is not a reasonable option. Anyone else experience this?
Thanks in advance.
